Fatih Celik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Fatih Celik has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Hanifi Canakci
Faculty of Engineering, Department of Civil Engineering, The University of Gaziantep , Gaziantep, Turkey
8 shared publications- Ersin Aydin
Niğde Ömer Halisdemir University
2 shared publications - Seyma Teberik
Civil Engineering Department, Nigde Omer Halisdemir University, 51240 Niğde, Türkiye
2 shared publications - Andaç Batur Çolak
Niğde Ömer Halisdemir University
1 shared publication Aram Al-Kaki
1 shared publicationAram Aziz
1 shared publication
Latest Publications
- Open Access
- 15 April 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (2) , 791-802
Sismik yükler altında yapı-kazık-zemin etkileşimi kapsamında kinematik ve eylemsizlik etkileşim analizlerinin Plaxis-3D sonlu elemanlar programıyla modellenmesi-Bir vaka analizi
Kazıklı radye temel sistemleri yardımıyla üst yapıdan gelen yükler güvenle sağlam zeminlere aktarılmaktadır. Deprem kuvvetleri altında kazıklı radye tasarımları Yapı-Kazık-Zemin etkileşimi (YKZE) analizleriyle yapılmaktadır. Bu çözüm yaklaşımı çeşitli yazılım ve bilgisayar donanım imkânlarına bağlı olarak yarı sonsuz modelleyen yaklaşımlarla çözülebilmektedir. Bu yaklaşımlar zemin ortamı ile yapının birlikte modellendiği ortak sistem modeli veya zemin temel sistemi ile yapının ayrı ayrı çözülerek entegre edildiği alt sistem modelidir. Zemin modelinin daha gerçekçi tanımlanabildiği bir sayısal ortamda kinematik ve eylemsizlik analizlerinin yapılması yeni bir yaklaşım olarak değerlendirilmiştir. Bu çalışmada bu durum amaçlanarak bir vaka analizi olarak Gaziantep ilinde yapılması planlanan toplam 13 katlı yapının kazıklı radye temel sistemi TBDY-2018 (Türkiye Bina Deprem Yönetmeliği) kapsamında Alt sistem Yöntem-III durumu dikkate alınarak tasarlanmış ve gerek kinematik analiz gerekse de eylemsizlik analizi gelişmiş bir sonlu elemanlar analiz programı olan Plaxis-3D yazılımıyla yapılarak alternatif bir hesap yöntemi sunulmuştur. Bu çalışma ile rjitlik farkı çok yüksek olmayan zemin profilleri arasında kinematik etkileşimin etkin olmayacağı gösterilmiştir.
- 15 April 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (2) , 791-802
Open AccessSismik yükler altında yapı-kazık-zemin etkileşimi kapsamında kinematik ve eylemsizlik etkileşim analizlerinin Plaxis-3D sonlu elemanlar programıyla modellenmesi-Bir vaka analizi
Kazıklı radye temel sistemleri yardımıyla üst yapıdan gelen yükler güvenle sağlam zeminlere aktarılmaktadır. Deprem kuvvetleri altında kazıklı radye tasarımları Yapı-Kazık-Zemin etkileşimi (YKZE) analizleriyle yapılmaktadır. Bu çözüm yaklaşımı çeşitli yazılım ve bilgisayar donanım imkânlarına bağlı olarak yarı sonsuz modelleyen yaklaşımlarla çözülebilmektedir. Bu yaklaşımlar zemin ortamı ile yapının birlikte modellendiği ortak sistem modeli veya zemin temel sistemi ile yapının ayrı ayrı çözülerek entegre edildiği alt sistem modelidir. Zemin modelinin daha gerçekçi tanımlanabildiği bir sayısal ortamda kinematik ve eylemsizlik analizlerinin yapılması yeni bir yaklaşım olarak değerlendirilmiştir. Bu çalışmada bu durum amaçlanarak bir vaka analizi olarak Gaziantep ilinde yapılması planlanan toplam 13 katlı yapının kazıklı radye temel sistemi TBDY-2018 (Türkiye Bina Deprem Yönetmeliği) kapsamında Alt sistem Yöntem-III durumu dikkate alınarak tasarlanmış ve gerek kinematik analiz gerekse de eylemsizlik analizi gelişmiş bir sonlu elemanlar analiz programı olan Plaxis-3D yazılımıyla yapılarak alternatif bir hesap yöntemi sunulmuştur. Bu çalışma ile rjitlik farkı çok yüksek olmayan zemin profilleri arasında kinematik etkileşimin etkin olmayacağı gösterilmiştir.
- Open Access
Influence of Bracing Systems on Pile Design Parameters: A Structure–Soil–Pile Interaction Approach
Structural damages occurred during any earthquake arise not only from structural design flaw but also from the variability of sub-base soil behavior and the foundation system. For this reason, structure–soil–pile interaction has an important place in evaluating the behavior of a structure under dynamic effects. Bored pile application, which is one of the deep foundation systems, is a widely used method in the world to transfer the loads coming from the structure to the ground safely in problematic grounds. For this reason, in pile foundation system designs, how bored pile foundation systems will affect the structural design under earthquake loads is considered an important issue. In particular, how diagonally braced steel structures with piled raft foundation systems will behave under earthquake effects has been evaluated as a subject that needs to be examined. For this reason, this situation was evaluated as the main purpose of this study. The effect of the bored pile systems designed in different orientations on the behavior of diagonally braced steel structures during an earthquake under kinematic and inertial effects was investigated in detail within the scope of this study. Numerical analyses, based on data from shake table experiments on a scaled superstructure, examine various pile design scenarios. Experimental base shear force measurements informed the development of numerical scenarios, which varied pile lengths and inter-pile distances while maintaining constant pile diameters. This study analyzed the kinematic and inertial effects on the piles, offering insights into their structural behavior under seismic conditions. The increase in pile length and the increase in the distance between the piles caused a significant increase in the bending moment and shear force, which have an important place in pile design.
Open AccessInfluence of Bracing Systems on Pile Design Parameters: A Structure–Soil–Pile Interaction Approach
Structural damages occurred during any earthquake arise not only from structural design flaw but also from the variability of sub-base soil behavior and the foundation system. For this reason, structure–soil–pile interaction has an important place in evaluating the behavior of a structure under dynamic effects. Bored pile application, which is one of the deep foundation systems, is a widely used method in the world to transfer the loads coming from the structure to the ground safely in problematic grounds. For this reason, in pile foundation system designs, how bored pile foundation systems will affect the structural design under earthquake loads is considered an important issue. In particular, how diagonally braced steel structures with piled raft foundation systems will behave under earthquake effects has been evaluated as a subject that needs to be examined. For this reason, this situation was evaluated as the main purpose of this study. The effect of the bored pile systems designed in different orientations on the behavior of diagonally braced steel structures during an earthquake under kinematic and inertial effects was investigated in detail within the scope of this study. Numerical analyses, based on data from shake table experiments on a scaled superstructure, examine various pile design scenarios. Experimental base shear force measurements informed the development of numerical scenarios, which varied pile lengths and inter-pile distances while maintaining constant pile diameters. This study analyzed the kinematic and inertial effects on the piles, offering insights into their structural behavior under seismic conditions. The increase in pile length and the increase in the distance between the piles caused a significant increase in the bending moment and shear force, which have an important place in pile design.
- Open Access
- 29 December 2023
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 11, 42-54
COMPARISON OF NUMERICAL ANALYSIS OF A SINGLE-SPAN STEEL PROTOTYPE STRUCTURE AND A SCALE MODEL STRUCTURE UNDER THE EFFECT OF SEISMIC LOADS
One of the biggest problems encountered in many experimental studies is examining a real-size structure in the field or in a laboratory environment. With today's technological opportunities, it is possible to experimentally examine a real-sized structure in the field or in a laboratory environment. However, to do this, the manufacture of a large, real-size structure, experimental setup and measuring devices are required, which are costly. For this reason, it is not always possible to reach such a laboratory environment. It is very difficult to experimentally examine large-scale structures both economically and in terms of time saving. In this context, in this study, a scaling factor (λ) widely accepted in the literature was used to design a scaled model to represent a real-size structure. λ=10 was used in this scaling approach. A real-size three-story single-span steel prototype building was scaled to a laboratory-scale model structure and analyzed digitally with the Sap2000 program. The natural period/frequency values of the real-size prototype structure and the scaled model modeled in the Sap2000 program were examined. Later, Time history analyzes were performed using real earthquake records from El Centro (1940), Kobe (1995) and Northridge (1994). While real earthquake records were used as they were in the analysis of the prototype structure, these real earthquake records were used by scaling them depending on the scaling factor λ in the analysis of the scaled model. Subsequently, the digital analyzes of the prototype and scaled structure were compared by looking at the acceleration and displacement values of each floor. It was observed that the results were close to each other when scaled according to the scaling factor (λ). This situation demonstrated the accuracy of the scaling rates applied within the scope of the study. Thus, it has been shown that a real-size structure can be scaled to a model in a laboratory environment with correct scaling methods and that this prototype structure can be analyzed with more economical and simple methods.
- 29 December 2023
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 11, 42-54
Open AccessCOMPARISON OF NUMERICAL ANALYSIS OF A SINGLE-SPAN STEEL PROTOTYPE STRUCTURE AND A SCALE MODEL STRUCTURE UNDER THE EFFECT OF SEISMIC LOADS
One of the biggest problems encountered in many experimental studies is examining a real-size structure in the field or in a laboratory environment. With today's technological opportunities, it is possible to experimentally examine a real-sized structure in the field or in a laboratory environment. However, to do this, the manufacture of a large, real-size structure, experimental setup and measuring devices are required, which are costly. For this reason, it is not always possible to reach such a laboratory environment. It is very difficult to experimentally examine large-scale structures both economically and in terms of time saving. In this context, in this study, a scaling factor (λ) widely accepted in the literature was used to design a scaled model to represent a real-size structure. λ=10 was used in this scaling approach. A real-size three-story single-span steel prototype building was scaled to a laboratory-scale model structure and analyzed digitally with the Sap2000 program. The natural period/frequency values of the real-size prototype structure and the scaled model modeled in the Sap2000 program were examined. Later, Time history analyzes were performed using real earthquake records from El Centro (1940), Kobe (1995) and Northridge (1994). While real earthquake records were used as they were in the analysis of the prototype structure, these real earthquake records were used by scaling them depending on the scaling factor λ in the analysis of the scaled model. Subsequently, the digital analyzes of the prototype and scaled structure were compared by looking at the acceleration and displacement values of each floor. It was observed that the results were close to each other when scaled according to the scaling factor (λ). This situation demonstrated the accuracy of the scaling rates applied within the scope of the study. Thus, it has been shown that a real-size structure can be scaled to a model in a laboratory environment with correct scaling methods and that this prototype structure can be analyzed with more economical and simple methods.
- Open Access
- 1 January 2023
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 19 (1) , 135-158
An Experimental Investigation on Workability and Bleeding Behaviors of Cement Pastes Doped with Nano Titanium Oxide (n-TiO2) Nanoparticles and Fly Ash
In this study, the workability of cement-based grouts containing n-TiO2 nanoparticles and fly ash has been investigated experimentally. Several characteristic quantities (including, but not limited to, the marsh cone flow time, the mini slump spreading diameter and the plate cohesion meter value) have been measured for different percentages of these additives. The use of fly ash as a mineral additive has been found to result in improvements in terms of workability behavior as expected. Moreover, if nano titanium oxide is also used, an improvement can be obtained regarding the bleeding values for the cement-based grout mixes. Using such experimental data, a multi-layer perceptron artificial neural network model has been developed (5 neurons in the hidden layer of the network model have been developed using a total of 42 experimental data). 70% of the data employed in this model have been used for training, 15% for validation and 15% for the test phase. The results demonstrate that the arti- ficial neural network model can predict Marsh cone flow time, mini slump spreading diameter and plate cohesion meter values with an average error of 0.15%.
- 1 January 2023
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 19 (1) , 135-158
Open AccessAn Experimental Investigation on Workability and Bleeding Behaviors of Cement Pastes Doped with Nano Titanium Oxide (n-TiO2) Nanoparticles and Fly Ash
In this study, the workability of cement-based grouts containing n-TiO2 nanoparticles and fly ash has been investigated experimentally. Several characteristic quantities (including, but not limited to, the marsh cone flow time, the mini slump spreading diameter and the plate cohesion meter value) have been measured for different percentages of these additives. The use of fly ash as a mineral additive has been found to result in improvements in terms of workability behavior as expected. Moreover, if nano titanium oxide is also used, an improvement can be obtained regarding the bleeding values for the cement-based grout mixes. Using such experimental data, a multi-layer perceptron artificial neural network model has been developed (5 neurons in the hidden layer of the network model have been developed using a total of 42 experimental data). 70% of the data employed in this model have been used for training, 15% for validation and 15% for the test phase. The results demonstrate that the arti- ficial neural network model can predict Marsh cone flow time, mini slump spreading diameter and plate cohesion meter values with an average error of 0.15%.
- 3 July 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (14) , 1-17
Mapping investigation based on engineering geology of a developing urban area (Niğde, Turkey)
- 3 July 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (14) , 1-17
Mapping investigation based on engineering geology of a developing urban area (Niğde, Turkey)
- 8 July 2019
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 12 (14) , 429
An Analytical Approach for Piled-Raft Foundation Design Based on Equivalent Pier and Raft Analyses by Using 2D Finite Element Method
- 8 July 2019
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 12 (14) , 429
An Analytical Approach for Piled-Raft Foundation Design Based on Equivalent Pier and Raft Analyses by Using 2D Finite Element Method
- 2 April 2018
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 24 (8) , 1245-1260
Examination of the mechanical properties and failure pattern of soilcrete mixtures modified with rice husk ash
This paper evaluates the unconfined compressive strength (UCS), stability (bleeding), modulus of elasticity and failure patterns of cement-based grout mixtures that were prepared by placing of rice husk ash (RHA) with cement at various water to binder (w/b) ratios. In order to investigate these parameters, UCS and bleeding tests were conducted on the soilcrete samples that prepared at 5, 10, 20 and 30% replacement level of RHA with cement for .75, 1.00 and 1.25 w/b ratios. Test results showed that the UCS values of the samples for 28 day curing are higher than 1 MPa and E/q u ratios obtained from soilcrete mixtures were less than the corresponding value from slurry clay–cement mixes given in the literature. In addition, all bleeding test results are lower than the level of .5%. Finally, most of the mixtures prepared for this study failed along foliations.
- 2 April 2018
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 24 (8) , 1245-1260
Examination of the mechanical properties and failure pattern of soilcrete mixtures modified with rice husk ash
This paper evaluates the unconfined compressive strength (UCS), stability (bleeding), modulus of elasticity and failure patterns of cement-based grout mixtures that were prepared by placing of rice husk ash (RHA) with cement at various water to binder (w/b) ratios. In order to investigate these parameters, UCS and bleeding tests were conducted on the soilcrete samples that prepared at 5, 10, 20 and 30% replacement level of RHA with cement for .75, 1.00 and 1.25 w/b ratios. Test results showed that the UCS values of the samples for 28 day curing are higher than 1 MPa and E/q u ratios obtained from soilcrete mixtures were less than the corresponding value from slurry clay–cement mixes given in the literature. In addition, all bleeding test results are lower than the level of .5%. Finally, most of the mixtures prepared for this study failed along foliations.
- 28 June 2017
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 23 (9) , 1094-1105
Effect of sand column on compressibility and shear strength properties of peat
Peat is found in many countries throughout the world where it can be generally seen in thick layers in limited areas. Peat is an extreme form of soft soil and is considered problematic due to the low shear strength and large compressibility. This project presents laboratory finding on the compressibility and shear strength characteristics of fibrous peat with sand column. The peat used in the study is classified as fibrous peat and H1–H4 in Von Post scale. Its liquid limit is 119%. In all tests, the peat used for the tests passing 2 mm and remain on .15 mm. The rounded sand used for making sand column is poorly graded passing from 2 mm sieve size and retaining on 1 mm sieve size. The tests conducted to investigate effect of area ratio of sand column on shear strength and compressibility of the peat. Three different area ratios were used for both compressibility and shear strength tests. Consolidation test results showed that when the area ratio increases compressibility characteristic of the peat improved. Shear strength of the organic soil was also affected from the sand column.
- 28 June 2017
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 23 (9) , 1094-1105
Effect of sand column on compressibility and shear strength properties of peat
Peat is found in many countries throughout the world where it can be generally seen in thick layers in limited areas. Peat is an extreme form of soft soil and is considered problematic due to the low shear strength and large compressibility. This project presents laboratory finding on the compressibility and shear strength characteristics of fibrous peat with sand column. The peat used in the study is classified as fibrous peat and H1–H4 in Von Post scale. Its liquid limit is 119%. In all tests, the peat used for the tests passing 2 mm and remain on .15 mm. The rounded sand used for making sand column is poorly graded passing from 2 mm sieve size and retaining on 1 mm sieve size. The tests conducted to investigate effect of area ratio of sand column on shear strength and compressibility of the peat. Three different area ratios were used for both compressibility and shear strength tests. Consolidation test results showed that when the area ratio increases compressibility characteristic of the peat improved. Shear strength of the organic soil was also affected from the sand column.
- 18 March 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 42 (9) , 3819-3827
Fresh Properties of Cementitious Grout with Rice Husk Powder
- 18 March 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 42 (9) , 3819-3827
Fresh Properties of Cementitious Grout with Rice Husk Powder
- 1 December 2016
- Published by Elsevier in Soils and Foundations
- Vol. 56 (6) , 965-972
Friction characteristics of organic soil with construction materials
- 1 December 2016
- Published by Elsevier in Soils and Foundations
- Vol. 56 (6) , 965-972
Friction characteristics of organic soil with construction materials