Eran Socher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eran Socher has a total of 117 co-authors. Here are the top co-authors by number of shared publications:
Samuel Jameson
School of Electrical Engineering, Tel Aviv University, Tel Aviv, Israel
15 shared publicationsY. Nemirovsky
Dept. of Electr. Eng., Technion-Israel Inst. of Technol., Haifa, Israel
15 shared publicationsO. Bochobza-Degani
11 shared publicationsSai-Wang Tam
Electrical Engineering Department, University of California Los Angeles, Los Angeles, CA, USA
7 shared publicationsBassam Khamaisi
School of Electrical Engineering, Tel Aviv University, Israel
6 shared publications- Mau-Chung Frank Chang
Department of Electrical and Computer Engineering, University of California, Los Angeles, Los Angeles, CA, USA
6 shared publications
Latest Publications
- Open Access
- 1 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 6 (3) , 675-688
A Compact CMOS W -Band Transmitter Front-End With 7-Bit Phase Shifter Resolution
Vector modulation circuits such as cartesian phase shifters and IQ modulators are integral components of mm-wave transceivers, relying on quadrature signal summation. This work analyzes conventional quadrature summation techniques and provides an in-depth study of the widely used current-summation method, identifying its limitations and the resulting distortion of the output constellation. Guided by these insights, we present a W-band 65 nm bulk CMOS transmitter front-end that integrates a voltage-summation vector modulator (VM) and a power amplifier. The VM features a transformer-based combiner with a single secondary inductor that performs a weighted summation of the quadrature fluxes generated by two primary inductors. Using a low-complexity predistortion algorithm, a linear and predictable 1024-point constellation is achieved with 9% Error Vector Magnitude (EVM). Additionally, phase shift keying (PSK) constellations were measured, demonstrating true 7-bit phase resolution across the 95–97.5 GHz range with minimum 1° phase RMSE.
- 1 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 6 (3) , 675-688
Open AccessA Compact CMOS W -Band Transmitter Front-End With 7-Bit Phase Shifter Resolution
Vector modulation circuits such as cartesian phase shifters and IQ modulators are integral components of mm-wave transceivers, relying on quadrature signal summation. This work analyzes conventional quadrature summation techniques and provides an in-depth study of the widely used current-summation method, identifying its limitations and the resulting distortion of the output constellation. Guided by these insights, we present a W-band 65 nm bulk CMOS transmitter front-end that integrates a voltage-summation vector modulator (VM) and a power amplifier. The VM features a transformer-based combiner with a single secondary inductor that performs a weighted summation of the quadrature fluxes generated by two primary inductors. Using a low-complexity predistortion algorithm, a linear and predictable 1024-point constellation is achieved with 9% Error Vector Magnitude (EVM). Additionally, phase shift keying (PSK) constellations were measured, demonstrating true 7-bit phase resolution across the 95–97.5 GHz range with minimum 1° phase RMSE.
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 16 (5) , 583-596
A 6 × 6 Stitched Array of 320 GHz CMOS Active Pixel Detectors
This article details the design and characterization of a 6x6 detector array fabricated with 65 nm complementary metal-oxide-semiconductor (CMOS), where the pixels in the array are stitched together with wirebonds as opposed to monolithic integration. Each pixel contains an on-chip loop antenna and baseband chopper amplifier with 32 dB gain. The design focuses on maintaining detector performance under array scaling and baseband integration. Measurement results of the chopper breakout, standalone pixel, and array are presented, where the standalone pixel achieves an RV (voltage responsivity) of 120 kV/W and record noise-equivalent power of 6 pW/√Hz with the baseband amplifier; and the mean array RV is 80 kV/W. The chip pixel area is 950 μm × 600 μm.
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 16 (5) , 583-596
A 6 × 6 Stitched Array of 320 GHz CMOS Active Pixel Detectors
This article details the design and characterization of a 6x6 detector array fabricated with 65 nm complementary metal-oxide-semiconductor (CMOS), where the pixels in the array are stitched together with wirebonds as opposed to monolithic integration. Each pixel contains an on-chip loop antenna and baseband chopper amplifier with 32 dB gain. The design focuses on maintaining detector performance under array scaling and baseband integration. Measurement results of the chopper breakout, standalone pixel, and array are presented, where the standalone pixel achieves an RV (voltage responsivity) of 120 kV/W and record noise-equivalent power of 6 pW/√Hz with the baseband amplifier; and the mean array RV is 80 kV/W. The chip pixel area is 950 μm × 600 μm.
- Open Access
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (6) , 1293-1307
Temperature-Compensated Multi-Level CMOS Modulators Operating From 10 K to 300 K for Cryogenic Interconnects
This work presents temperature-compensated cryogenic complementary metal-oxide-semiconductor (CMOS) modulators operating over a 10 K to 300 K temperature range, suitable for intra- and inter-thermal cryogenic communications. Conventional metal-based coax cables suffer from a fundamental trade-off between thermal load and frequency-dependent attenuation, where lower thermal load results in higher electromagnetic attenuation. The recent surge in cryogenic high-performance computing and quantum computing has driven the demand for scalable cryogenic interconnect solutions. New techniques in optical fibers and millimeter-wave backscatter transceivers have demonstrated the ability to transport digital data between thermally isolated temperatures without the need for coaxial cables. Our new modulator can integrate (at the package or chip level) with millimeter-wave transmitters co-located on the same thermal condition while supporting bandwidth-efficient modulations such as multi-level pulse amplitude modulations. Based on this motivation, we implemented a current-steering 2-bit modulator in a 65-nanometer (nm) bulk CMOS process. The modulator achieves a data rate of 13 gigabits per second (Gb/s) while consuming 15.4 mW under a 1.2 V supply at 10 K, resulting in an energy efficiency of 1.18 picojoules per bit (pJ/b). In addition to previously demonstrated optical fibers and millimeter-wave backscatter, we implemented a 150 GHz (GHz) transmitter utilizing the same current-steering modulator scheme in a 28-nm CMOS process. We established contactless connections between thermally isolated systems operating at 10 K and 300 K, achieving a data rate of 8 Gb/s.
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (6) , 1293-1307
Open AccessTemperature-Compensated Multi-Level CMOS Modulators Operating From 10 K to 300 K for Cryogenic Interconnects
This work presents temperature-compensated cryogenic complementary metal-oxide-semiconductor (CMOS) modulators operating over a 10 K to 300 K temperature range, suitable for intra- and inter-thermal cryogenic communications. Conventional metal-based coax cables suffer from a fundamental trade-off between thermal load and frequency-dependent attenuation, where lower thermal load results in higher electromagnetic attenuation. The recent surge in cryogenic high-performance computing and quantum computing has driven the demand for scalable cryogenic interconnect solutions. New techniques in optical fibers and millimeter-wave backscatter transceivers have demonstrated the ability to transport digital data between thermally isolated temperatures without the need for coaxial cables. Our new modulator can integrate (at the package or chip level) with millimeter-wave transmitters co-located on the same thermal condition while supporting bandwidth-efficient modulations such as multi-level pulse amplitude modulations. Based on this motivation, we implemented a current-steering 2-bit modulator in a 65-nanometer (nm) bulk CMOS process. The modulator achieves a data rate of 13 gigabits per second (Gb/s) while consuming 15.4 mW under a 1.2 V supply at 10 K, resulting in an energy efficiency of 1.18 picojoules per bit (pJ/b). In addition to previously demonstrated optical fibers and millimeter-wave backscatter, we implemented a 150 GHz (GHz) transmitter utilizing the same current-steering modulator scheme in a 28-nm CMOS process. We established contactless connections between thermally isolated systems operating at 10 K and 300 K, achieving a data rate of 8 Gb/s.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 1964-1974
A Watt-Level, 3.3-V Triple-Stack Switched Capacitor Digital PA in FinFET Technology
This work proposes and analyzes a new circuit topology that enables reliable triple-transistor stacking in the switched-capacitor digital power amplifier (SC-DPA) working from a 3.3-V supply, about three times the process maximum allowed voltage across the transistor nodes ( $V_{D,\text{Max}}$ ). The proposed topology employs capacitive feedback (CF) to meet device voltage constraints. Higher supply voltage usage results in reduced supply ripples and improved memory effects while allowing higher power watt-level SC-DPA. A 5–7-GHz, dual-core Doherty-like combining SC-DPA prototype was implemented and integrated into an all-digital polar transmitter (DPTX) using 16-nm FinFET CMOS technology. The SC-DPA demonstrates a maximum power ( $P_{\text{max}}$ )/power efficiency (PE) of 30.15 dBm/34.7% at 5.2 GHz. An error vector magnitude (EVM)/power consumption of $-$ 38 dB/830 mW is measured at 6.1-GHz and 9-dB BO (dBBO) from $P_{\text{max}}$ , thus meeting MCS13 4096-QAM OFDM Wi-Fi7 requirement. The high-temperature operating life (HTOL) accelerating aging test was performed showing the ability to meet the expected lifetime of the device with only 0.5-dB $P_{\text{max}}$ degradation.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 1964-1974
A Watt-Level, 3.3-V Triple-Stack Switched Capacitor Digital PA in FinFET Technology
This work proposes and analyzes a new circuit topology that enables reliable triple-transistor stacking in the switched-capacitor digital power amplifier (SC-DPA) working from a 3.3-V supply, about three times the process maximum allowed voltage across the transistor nodes ( $V_{D,\text{Max}}$ ). The proposed topology employs capacitive feedback (CF) to meet device voltage constraints. Higher supply voltage usage results in reduced supply ripples and improved memory effects while allowing higher power watt-level SC-DPA. A 5–7-GHz, dual-core Doherty-like combining SC-DPA prototype was implemented and integrated into an all-digital polar transmitter (DPTX) using 16-nm FinFET CMOS technology. The SC-DPA demonstrates a maximum power ( $P_{\text{max}}$ )/power efficiency (PE) of 30.15 dBm/34.7% at 5.2 GHz. An error vector magnitude (EVM)/power consumption of $-$ 38 dB/830 mW is measured at 6.1-GHz and 9-dB BO (dBBO) from $P_{\text{max}}$ , thus meeting MCS13 4096-QAM OFDM Wi-Fi7 requirement. The high-temperature operating life (HTOL) accelerating aging test was performed showing the ability to meet the expected lifetime of the device with only 0.5-dB $P_{\text{max}}$ degradation.
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (5) , 556-559
A Two-Way Power Combined Ka-Band Rectifier for Low Input Power Energy Harvesting
In this letter, we propose an RF power combining approach for energy harvesting at Ka -band frequencies. A two-way 28-nm CMOS rectifier is presented, utilizing ultralow threshold voltage (ULVT) transistors for efficient rectification of low voltage swing input signals. The power combiner is a compact voltage summation design that minimizes the losses associated with transformer-based power combiners at mm-Wave frequencies. The rectifier achieves a record 13% power conversion efficiency (PCE) for $-$ 20 dBm input power per port, and peak PCE of 24% for $-$ 14 dBm input power per port.
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (5) , 556-559
A Two-Way Power Combined Ka-Band Rectifier for Low Input Power Energy Harvesting
In this letter, we propose an RF power combining approach for energy harvesting at Ka -band frequencies. A two-way 28-nm CMOS rectifier is presented, utilizing ultralow threshold voltage (ULVT) transistors for efficient rectification of low voltage swing input signals. The power combiner is a compact voltage summation design that minimizes the losses associated with transformer-based power combiners at mm-Wave frequencies. The rectifier achieves a record 13% power conversion efficiency (PCE) for $-$ 20 dBm input power per port, and peak PCE of 24% for $-$ 14 dBm input power per port.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (7) , 3041-3049
A High Sensitivity CMOS Rectifier for 5G mm-Wave Energy Harvesting
This manuscript details the design and analysis of a CMOS rectifier in TSMC 65 nm for the 5G NR2 band and aims to overcome the challenge of achieving high rectified voltage while optimizing for PCE (power conversion efficiency). Using a frequency-scaled testbench, the transistor currents are investigated, providing key insights on the rectification mechanism that guide the design. The testbench is then used to determine the optimal number, $N$ , of summing rectifiers to be used in a power splitting and voltage summing strategy that maximizes PCE for high target output voltage. In addition, a unit-cell rectifier design highlights how to target a specific output voltage while maintaining dc power matching for optimal PCE. Two rectifiers are presented: a unit-cell rectifier targeting -13 dBm and an $N$ -scaled rectifier targeting $-$ 10 dBm. Both designs achieve a PCE of 15% at 27.5 GHz, while the former achieves 200 mV and the latter achieves 400 mV output voltage, for their respective target input powers. Finally, a survey of rectifiers operating around 30 GHz is presented where a x2 improvement over the current state-of-the-art is ascertained.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (7) , 3041-3049
A High Sensitivity CMOS Rectifier for 5G mm-Wave Energy Harvesting
This manuscript details the design and analysis of a CMOS rectifier in TSMC 65 nm for the 5G NR2 band and aims to overcome the challenge of achieving high rectified voltage while optimizing for PCE (power conversion efficiency). Using a frequency-scaled testbench, the transistor currents are investigated, providing key insights on the rectification mechanism that guide the design. The testbench is then used to determine the optimal number, $N$ , of summing rectifiers to be used in a power splitting and voltage summing strategy that maximizes PCE for high target output voltage. In addition, a unit-cell rectifier design highlights how to target a specific output voltage while maintaining dc power matching for optimal PCE. Two rectifiers are presented: a unit-cell rectifier targeting -13 dBm and an $N$ -scaled rectifier targeting $-$ 10 dBm. Both designs achieve a PCE of 15% at 27.5 GHz, while the former achieves 200 mV and the latter achieves 400 mV output voltage, for their respective target input powers. Finally, a survey of rectifiers operating around 30 GHz is presented where a x2 improvement over the current state-of-the-art is ascertained.
- Open Access
- 21 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (2) , 275-285
A 90-98 GHz CMOS Transmitter Frontend for Concurrent Phase-Coded FMCW Radar Applications
A 90-98 GHz transmitter frontend fabricated in TSMC 65-nm bulk CMOS, capable of concurrent radar-communications applications is presented. A transmitter is proposed that can be used for phase-coded frequency-modulated continuous wave (PC-FMCW) radar as well as for data transmission and interference mitigation. The transmitter architecture is based on an 8-12 GHz IF and ×8 frequency multiplication of a 10-11 GHz local oscillator (LO). Vector IQ summation provides amplitude and phase control, followed by an output power amplifier. Two X-band inputs make the transmitter attractive for a concurrent radar-communication systems as one input is frequency multiplied ×8 while the other is not, allowing upconverting modulated X-band signals. The transmitter achieves full IQ plane control, capable of supporting high-resolution beam steering with ${\mathrm{P}}_{\text{SAT}}$ of 13.7 dBm at 94 GHz. The transmitter consumes 320 mW from a 1.2 V supply ( $\mathrm{V}_{\text{DD}}$ ) and occupies 0.2 mm2 core area. The transmitter also presents excellent spectral purity with >30 dB harmonic rejection and a conversion gain of 28 dB.- 21 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (2) , 275-285
Open AccessA 90-98 GHz CMOS Transmitter Frontend for Concurrent Phase-Coded FMCW Radar Applications
A 90-98 GHz transmitter frontend fabricated in TSMC 65-nm bulk CMOS, capable of concurrent radar-communications applications is presented. A transmitter is proposed that can be used for phase-coded frequency-modulated continuous wave (PC-FMCW) radar as well as for data transmission and interference mitigation. The transmitter architecture is based on an 8-12 GHz IF and ×8 frequency multiplication of a 10-11 GHz local oscillator (LO). Vector IQ summation provides amplitude and phase control, followed by an output power amplifier. Two X-band inputs make the transmitter attractive for a concurrent radar-communication systems as one input is frequency multiplied ×8 while the other is not, allowing upconverting modulated X-band signals. The transmitter achieves full IQ plane control, capable of supporting high-resolution beam steering with ${\mathrm{P}}_{\text{SAT}}$ of 13.7 dBm at 94 GHz. The transmitter consumes 320 mW from a 1.2 V supply ( $\mathrm{V}_{\text{DD}}$ ) and occupies 0.2 mm2 core area. The transmitter also presents excellent spectral purity with >30 dB harmonic rejection and a conversion gain of 28 dB. - 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 11 (1) , 62-69
A Zero Bias J-Band Antenna-Coupled Detector in 65-nm CMOS
An improved topology for sub-THz radiation detection realized in 65 nm CMOS, including an on-chip antenna and using zero biasing is presented in this paper. The topology is based on a differential Colpitts topology working in reverse-mode and leverages the non-linearity with respect to vDS in subthreshold operation to rectify. The use of tuned inductors at the gates and sources of the transistor core create degenerative resonance feedback which further enhances the responsivity while working with zero bias eliminates 1/f noise to improve the NEP. Measurements demonstrated a voltage responsivity as high as 2 kV/W with a 3 dB RF BW of at least 50 GHz centered at 315 GHz and a record NEP of down to 3.5 pW/Hz, verified both at zero-IF and using chopping from 0.5 Hz up to 2 kHz. The chip occupies an area of 0.165 mm2 including pads.
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 11 (1) , 62-69
A Zero Bias J-Band Antenna-Coupled Detector in 65-nm CMOS
An improved topology for sub-THz radiation detection realized in 65 nm CMOS, including an on-chip antenna and using zero biasing is presented in this paper. The topology is based on a differential Colpitts topology working in reverse-mode and leverages the non-linearity with respect to vDS in subthreshold operation to rectify. The use of tuned inductors at the gates and sources of the transistor core create degenerative resonance feedback which further enhances the responsivity while working with zero bias eliminates 1/f noise to improve the NEP. Measurements demonstrated a voltage responsivity as high as 2 kV/W with a 3 dB RF BW of at least 50 GHz centered at 315 GHz and a record NEP of down to 3.5 pW/Hz, verified both at zero-IF and using chopping from 0.5 Hz up to 2 kHz. The chip occupies an area of 0.165 mm2 including pads.
- 8 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 454-457
A 280-GHz Digitally Controlled Four Port Chip-Scale Dielectric Resonator Antenna Transmitter With DiCAD True Time Delay
A 280 GHz, fully integrated and digitally controlled multiport coherent radiator is presented. The silicon die acts as a Chip Scale Dielectric Resonator Antenna (CSDRA) and is excited by four differential loop inductors. The chip incorporates a balun for an X band input signal, a 1 to 4 ultra-compact differential Wilkinson splitter and four x27 Active Multiplying Chains (AMC), which drive the four exciting elements. High resolution, digitally controlled True Time Delay (TTD) elements, based on Digitally Controlled Artificial Dielectric Transmission Lines (DiCAD) are used to calibrate the variations between channels to optimize overall broadside radiated power and enable beam steering of ±15∘ High resolution DACs are used to accurately set the bias through a 3 wire SPI module. Fabricated in 65 nm CMOS, the 1.4×2mm2 chip achieves a record EIRP of +21 dBm, a TRP of +8.5 dBm and a power density of 2.25 mW/mm2 with 0.72% total efficiency, without using any external lens, superstrate or post-processing.
- 8 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 454-457
A 280-GHz Digitally Controlled Four Port Chip-Scale Dielectric Resonator Antenna Transmitter With DiCAD True Time Delay
A 280 GHz, fully integrated and digitally controlled multiport coherent radiator is presented. The silicon die acts as a Chip Scale Dielectric Resonator Antenna (CSDRA) and is excited by four differential loop inductors. The chip incorporates a balun for an X band input signal, a 1 to 4 ultra-compact differential Wilkinson splitter and four x27 Active Multiplying Chains (AMC), which drive the four exciting elements. High resolution, digitally controlled True Time Delay (TTD) elements, based on Digitally Controlled Artificial Dielectric Transmission Lines (DiCAD) are used to calibrate the variations between channels to optimize overall broadside radiated power and enable beam steering of ±15∘ High resolution DACs are used to accurately set the bias through a 3 wire SPI module. Fabricated in 65 nm CMOS, the 1.4×2mm2 chip achieves a record EIRP of +21 dBm, a TRP of +8.5 dBm and a power density of 2.25 mW/mm2 with 0.72% total efficiency, without using any external lens, superstrate or post-processing.
- 12 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (12) , 7893-7904
W-Band Endfire 2-D Phased-Array Transmitter Based on ×9 CMOS Active Multiplier Chips
In this work we propose a scalable approach for a W-band 2D beam steering transmitter based on CMOS active frequency multiplier chips. Stacking of PCBs containing linear phased-arrays with end-fire antennas is used with X-band power splitting and phase control. The antenna design is discussed, explaining the choice of the SIW fed antipodal linearly tapered slot antenna (ALTSA). The concept is demonstrated in the 90-100 GHz bandwidth with 1 × 2, 1 × 4 and 2 × 2 arrays, achieving up to 29.4 dBm EIRP and ±10° of beam steering. Measurement results show excellent agreement with simulations, demonstrating the possibility of scalable two-dimensional phased arrays in W-band with low cost small silicon area consumption.
- 12 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (12) , 7893-7904
W-Band Endfire 2-D Phased-Array Transmitter Based on ×9 CMOS Active Multiplier Chips
In this work we propose a scalable approach for a W-band 2D beam steering transmitter based on CMOS active frequency multiplier chips. Stacking of PCBs containing linear phased-arrays with end-fire antennas is used with X-band power splitting and phase control. The antenna design is discussed, explaining the choice of the SIW fed antipodal linearly tapered slot antenna (ALTSA). The concept is demonstrated in the 90-100 GHz bandwidth with 1 × 2, 1 × 4 and 2 × 2 arrays, achieving up to 29.4 dBm EIRP and ±10° of beam steering. Measurement results show excellent agreement with simulations, demonstrating the possibility of scalable two-dimensional phased arrays in W-band with low cost small silicon area consumption.