Thomas H. Fletcher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Thomas H. Fletcher has a total of 97 co-authors. Here are the top co-authors by number of shared publications:
David R. Weise
US Forest Serv, USDA, PSW Res Stn, Fire & Fuels Program, Riverside, CA 92507 USA
5 shared publications- David R. Weise
Pacific Southwest Research Station, USDA Forest Service, Riverside, USA
5 shared publications Ronald J. Pugmire
Chemical Engineering Department, University of Utah, Salt Lake City, Utah 84112, United States
5 shared publicationsAaron D. Lewis
Department of Chemical Engineering, Brigham Young University, Provo, Utah 84602, United States
4 shared publicationsMark S. Solum
Department of Chemistry, ‡Department of Chemical Engineering, University of Utah, Salt Lake City, Utah 84112, United States
4 shared publicationsTroy Holland
Los Alamos National Laboratory
4 shared publications
Latest Publications
- Open Access
Pyrolysis of Foliage from 24 U.S. Plant Species with Recommendations for Physics-Based Wildland Fire Models
Pyrolysis of 24 samples of foliage from three U.S. regions with frequent wildland fires (Southeastern U.S., northern Utah and Southern California) was studied in a fuel-rich flat-flame burner system at 765 °C (for Southeastern U.S. samples) and 725 °C (for northern Utah and Southern California species), with a heating rate of approximately 180 °C/s. These conditions were selected to mimic the conditions of wildland fires. Individual plant samples were introduced to the high temperature zone in a flat-flame burner and pyrolysis products were collected. Tar was extracted and later analyzed by GC/MS. Light gases were collected and analyzed by GC/TCD. The estimated range for the average yields of tar and light gases were 48 to 62 wt% and 18 to 31 wt%, respectively. Apart from Eastwood’s manzanita (Arctostaphylos glandulosa Eastw.), aromatics were the major constituents of tar. The variations in the concentrations of tar compounds likely resulted from differences in biomass composition and physical characteristics of the foliage. The four major components of light gases from pyrolysis (wt% basis) were CO, CO2, CH4 and H2. Tar contributed more than 82% of the high heating value of volatiles. These data can be used to improve physical-based fire propagation models.
Open AccessPyrolysis of Foliage from 24 U.S. Plant Species with Recommendations for Physics-Based Wildland Fire Models
Pyrolysis of 24 samples of foliage from three U.S. regions with frequent wildland fires (Southeastern U.S., northern Utah and Southern California) was studied in a fuel-rich flat-flame burner system at 765 °C (for Southeastern U.S. samples) and 725 °C (for northern Utah and Southern California species), with a heating rate of approximately 180 °C/s. These conditions were selected to mimic the conditions of wildland fires. Individual plant samples were introduced to the high temperature zone in a flat-flame burner and pyrolysis products were collected. Tar was extracted and later analyzed by GC/MS. Light gases were collected and analyzed by GC/TCD. The estimated range for the average yields of tar and light gases were 48 to 62 wt% and 18 to 31 wt%, respectively. Apart from Eastwood’s manzanita (Arctostaphylos glandulosa Eastw.), aromatics were the major constituents of tar. The variations in the concentrations of tar compounds likely resulted from differences in biomass composition and physical characteristics of the foliage. The four major components of light gases from pyrolysis (wt% basis) were CO, CO2, CH4 and H2. Tar contributed more than 82% of the high heating value of volatiles. These data can be used to improve physical-based fire propagation models.
- Open Access
- 27 August 2024
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 33 (9)
Comparing gas composition from fast pyrolysis of live foliage measured in bench-scale and fire-scale experiments
Background: Fire models have used pyrolysis data from oxidising and non-oxidising environments for flaming combustion. In wildland fires pyrolysis, flaming and smouldering combustion typically occur in an oxidising environment (the atmosphere). Aims: Using compositional data analysis methods, determine if the composition of pyrolysis gases measured in non-oxidising and ambient (oxidising) atmospheric conditions were similar. Methods: Permanent gases and tars were measured in a fuel-rich (non-oxidising) environment in a flat flame burner (FFB). Permanent and light hydrocarbon gases were measured for the same fuels heated by a fire flame in ambient atmospheric conditions (oxidising environment). Log-ratio balances of the measured gases common to both environments (CO, CO2, CH4, H2, C6H6O (phenol), and other gases) were examined by principal components analysis (PCA), canonical discriminant analysis (CDA) and permutational multivariate analysis of variance (PERMANOVA). Key results: Mean composition changed between the non-oxidising and ambient atmosphere samples. PCA showed that flat flame burner (FFB) samples were tightly clustered and distinct from the ambient atmosphere samples. CDA found that the difference between environments was defined by the CO-CO2 log-ratio balance. PERMANOVA and pairwise comparisons found FFB samples differed from the ambient atmosphere samples which did not differ from each other. Conclusion: Relative composition of these pyrolysis gases differed between the oxidising and non-oxidising environments. This comparison was one of the first comparisons made between bench-scale and field scale pyrolysis measurements using compositional data analysis. Implications: These results indicate the need for more fundamental research on the early time-dependent pyrolysis of vegetation in the presence of oxygen.
- 27 August 2024
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 33 (9)
Open AccessComparing gas composition from fast pyrolysis of live foliage measured in bench-scale and fire-scale experiments
Background: Fire models have used pyrolysis data from oxidising and non-oxidising environments for flaming combustion. In wildland fires pyrolysis, flaming and smouldering combustion typically occur in an oxidising environment (the atmosphere). Aims: Using compositional data analysis methods, determine if the composition of pyrolysis gases measured in non-oxidising and ambient (oxidising) atmospheric conditions were similar. Methods: Permanent gases and tars were measured in a fuel-rich (non-oxidising) environment in a flat flame burner (FFB). Permanent and light hydrocarbon gases were measured for the same fuels heated by a fire flame in ambient atmospheric conditions (oxidising environment). Log-ratio balances of the measured gases common to both environments (CO, CO2, CH4, H2, C6H6O (phenol), and other gases) were examined by principal components analysis (PCA), canonical discriminant analysis (CDA) and permutational multivariate analysis of variance (PERMANOVA). Key results: Mean composition changed between the non-oxidising and ambient atmosphere samples. PCA showed that flat flame burner (FFB) samples were tightly clustered and distinct from the ambient atmosphere samples. CDA found that the difference between environments was defined by the CO-CO2 log-ratio balance. PERMANOVA and pairwise comparisons found FFB samples differed from the ambient atmosphere samples which did not differ from each other. Conclusion: Relative composition of these pyrolysis gases differed between the oxidising and non-oxidising environments. This comparison was one of the first comparisons made between bench-scale and field scale pyrolysis measurements using compositional data analysis. Implications: These results indicate the need for more fundamental research on the early time-dependent pyrolysis of vegetation in the presence of oxygen.
- Open Access
Characteristics of Pyrolysis Products of California Chaparral and Their Potential Effect on Wildland Fires
The aim of this study was to investigate the pyrolysis of selected California foliage and estimate the energy content of the released volatiles to show the significance of the pyrolysis of foliage and its role during wildland fires. While the majority of the volatiles released during the pyrolysis of foliage later combust and promote fire propagation, studies on the energy released from combustion of these compounds are scarce. Samples of chamise (Adenostoma fasciculatum), Eastwood’s manzanita (Arctostaphylos glandulosa), scrub oak (Quercus berberidifolia), hoaryleaf ceanothus (Ceanothus crassifolius), all native to southern California, and sparkleberry (Vaccinium arboreum), native to the southern U.S., were pyrolyzed at 725 °C with a heating rate of approximately 180 °C/s to mimic the conditions of wildland fires. Tar and light gases were collected and analyzed. Tar from chamise, scrub oak, ceanothus and sparkleberry was abundant in aromatics, especially phenol, while tar from manzanita was mainly composed of cycloalkenes. The four major components of light gases were CO, CO2, CH4 and H2. Estimated values for the high heating values (HHVs) of volatiles ranged between 18.9 and 23.2 (MJ/kg of biomass) with tar contributing to over 80% of the HHVs of the volatiles. Therefore, fire studies should consider the heat released from volatiles present in both tar and light gases during pyrolysis.
Open AccessCharacteristics of Pyrolysis Products of California Chaparral and Their Potential Effect on Wildland Fires
The aim of this study was to investigate the pyrolysis of selected California foliage and estimate the energy content of the released volatiles to show the significance of the pyrolysis of foliage and its role during wildland fires. While the majority of the volatiles released during the pyrolysis of foliage later combust and promote fire propagation, studies on the energy released from combustion of these compounds are scarce. Samples of chamise (Adenostoma fasciculatum), Eastwood’s manzanita (Arctostaphylos glandulosa), scrub oak (Quercus berberidifolia), hoaryleaf ceanothus (Ceanothus crassifolius), all native to southern California, and sparkleberry (Vaccinium arboreum), native to the southern U.S., were pyrolyzed at 725 °C with a heating rate of approximately 180 °C/s to mimic the conditions of wildland fires. Tar and light gases were collected and analyzed. Tar from chamise, scrub oak, ceanothus and sparkleberry was abundant in aromatics, especially phenol, while tar from manzanita was mainly composed of cycloalkenes. The four major components of light gases were CO, CO2, CH4 and H2. Estimated values for the high heating values (HHVs) of volatiles ranged between 18.9 and 23.2 (MJ/kg of biomass) with tar contributing to over 80% of the HHVs of the volatiles. Therefore, fire studies should consider the heat released from volatiles present in both tar and light gases during pyrolysis.
- 30 September 2021
- Published by Springer Nature
- p. 29-37
Advances in Modeling Coal Pyrolysis, Char Combustion, and Soot Formation from Coal and Biomass Tar
- 30 September 2021
- Published by Springer Nature
- p. 29-37
Advances in Modeling Coal Pyrolysis, Char Combustion, and Soot Formation from Coal and Biomass Tar
- 22 September 2021
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 35 (19) , 16264
Correction to Coal Char-CO2 Gasification Measurements and Modeling in a Pressurized Flat-Flame Burner
- 22 September 2021
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 35 (19) , 16264
Correction to Coal Char-CO2 Gasification Measurements and Modeling in a Pressurized Flat-Flame Burner
- Open Access
Merging of Horizontally and Vertically Separated Small-Scale Buoyant Flames
The purpose of this study was to investigate the merging behavior of small-scale buoyant flames that might be representative of flames from a leaf in a shrub. Zirconia felt pads soaked in n-heptane were suspended on thin rods and spaced both horizontally and vertically. Time-dependent video images from flames from two-pad and three-pad configurations were analyzed to determine merging probability, combined flame characteristics (height, area, and width), and changes in burn time. Correlations of these combined flame characteristics were developed based on horizontal and vertical spacing between the pads. Merging probability correlated with an exponential function that was quadratic in horizontal and/or vertical spacing. Flame heights corrected for vertical inter-pad spacing showed a maximum increase of 50% over single flame heights, and were correlated with an exponential decay function. Flame areas increased by a maximum of 34%, but on average were relatively constant. Corrected flame widths for the merged flames increased by as much as 55% in some configurations, but decreased by up to 73% in other configurations. Burn times for upper pads decreased when there was no horizontal spacing. The limited flame growth observed in these non-overlapping configurations in the horizontal dimension imply that overlapping configurations seem to be necessary for significant flame growth.
Open AccessMerging of Horizontally and Vertically Separated Small-Scale Buoyant Flames
The purpose of this study was to investigate the merging behavior of small-scale buoyant flames that might be representative of flames from a leaf in a shrub. Zirconia felt pads soaked in n-heptane were suspended on thin rods and spaced both horizontally and vertically. Time-dependent video images from flames from two-pad and three-pad configurations were analyzed to determine merging probability, combined flame characteristics (height, area, and width), and changes in burn time. Correlations of these combined flame characteristics were developed based on horizontal and vertical spacing between the pads. Merging probability correlated with an exponential function that was quadratic in horizontal and/or vertical spacing. Flame heights corrected for vertical inter-pad spacing showed a maximum increase of 50% over single flame heights, and were correlated with an exponential decay function. Flame areas increased by a maximum of 34%, but on average were relatively constant. Corrected flame widths for the merged flames increased by as much as 55% in some configurations, but decreased by up to 73% in other configurations. Burn times for upper pads decreased when there was no horizontal spacing. The limited flame growth observed in these non-overlapping configurations in the horizontal dimension imply that overlapping configurations seem to be necessary for significant flame growth.
- 1 August 2021
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 157
Pyrolysis kinetics of wildland vegetation using model-fitting methods
- 1 August 2021
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 157
Pyrolysis kinetics of wildland vegetation using model-fitting methods
- 14 June 2021
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 31 (1) , 24-45
Application of compositional data analysis to determine the effects of heating mode, moisture status and plant species on pyrolysates
Pyrolysate gas mixtures are multivariate and relative in nature. Statistical techniques applied to these data generally ignore their relative nature. Published data for permanent gases (CO, CO2, H2, CH4) and tars produced by pyrolysing 15 wildland fuels were reanalysed using compositional data analysis techniques. Mass and mole fractions were compositionally equivalent. Plant species, moisture status and heating mode effects on compositional balances formed from subsets of pyrolysates were tested. Plant species affected the amount of phenol, primary and secondary/tertiary tars relative to permanent gases and relative amounts of single- and multi-ring compounds. Plant moisture status affected the amount of CO relative to other permanent gases, of H2 to CH4 and tars to phenol. Heating mode and rate strongly influenced pyrolysate composition. Slow heating produced more primary tars relative to multi-ring tars than fast heating convective and combined radiant and convective heating modes. Slow heating produced relatively more compounds with fewer rings and fast heating produced relatively more multi-ring compounds. Compositional data analysis is a well-developed statistical methodology, providing models and methods equivalent to traditional ones, that accounts for the special constraining features of relative data. Future analysis of the compositional data related to wildland fire using compositional techniques is recommended.
- 14 June 2021
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 31 (1) , 24-45
Application of compositional data analysis to determine the effects of heating mode, moisture status and plant species on pyrolysates
Pyrolysate gas mixtures are multivariate and relative in nature. Statistical techniques applied to these data generally ignore their relative nature. Published data for permanent gases (CO, CO2, H2, CH4) and tars produced by pyrolysing 15 wildland fuels were reanalysed using compositional data analysis techniques. Mass and mole fractions were compositionally equivalent. Plant species, moisture status and heating mode effects on compositional balances formed from subsets of pyrolysates were tested. Plant species affected the amount of phenol, primary and secondary/tertiary tars relative to permanent gases and relative amounts of single- and multi-ring compounds. Plant moisture status affected the amount of CO relative to other permanent gases, of H2 to CH4 and tars to phenol. Heating mode and rate strongly influenced pyrolysate composition. Slow heating produced more primary tars relative to multi-ring tars than fast heating convective and combined radiant and convective heating modes. Slow heating produced relatively more compounds with fewer rings and fast heating produced relatively more multi-ring compounds. Compositional data analysis is a well-developed statistical methodology, providing models and methods equivalent to traditional ones, that accounts for the special constraining features of relative data. Future analysis of the compositional data related to wildland fire using compositional techniques is recommended.