Shelby L. Peterie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Shelby L. Peterie has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Julian Ivanov
Kansas Geological Survey
8 shared publications - Richard D. Miller
Kansas Geological Survey 3 , Lawrence, Kansas, .;.
7 shared publications - Steve Sloan
US Army Corps of Engineers, Vicksburg, MS, USA
5 shared publications - Dmitry Borisov
Kansas Geology Survey , 1930 Constant Ave, Lawrence, KS 66047
3 shared publications - Harley Cudney
U.S. Army Engineer Research and Development Center 2 , Vicksburg, Mississippi, .;;
2 shared publications - Jeroen Tromp
Department of Geosciences, Princeton University , Princeton, NJ 08544
2 shared publications
Latest Publications
- 20 July 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (6) , EN63-EN75
Passive multichannel analysis of surface waves using 1D and 2D receiver arrays
We use the seismic multichannel analysis of surface waves (MASW) method, which originally used active sources (i.e., controlled by users), to present a new alternative technique for surface-wave analysis of passive data (i.e., seismic sources not controlled by users). Our passive MASW technique uses two types of receiver arrays, 1D and 2D, for two different purposes. The 2D square array is used for assessing the number and directionality of passive seismic sources to help identify optimal time window(s) when such sources are of sufficient quality and aligned with the 1D receiver spread. Then, these time windows are used to selectively extract passive seismic data recorded by the 1D receiver spread for subsequent MASW analysis. In such a manner, this hybrid 1D–2D passive MASW approach can approximate the higher quality advantages of the active MASW method. This technique is successfully applied at a test site in southcentral Kansas taking advantage of train energy as the passive sources monitoring and assessing the potential development of vertically migrating voids that could endanger groundwater and infrastructure. The 1D–2D passive MASW method has proven beneficial for optimizing passive-data dispersion patterns and accurately assessing relative velocities for investigations with reduced labor costs and minimal added processing time and can be considered as a contribution to the surface-wave analysis tools.
- 20 July 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (6) , EN63-EN75
Passive multichannel analysis of surface waves using 1D and 2D receiver arrays
We use the seismic multichannel analysis of surface waves (MASW) method, which originally used active sources (i.e., controlled by users), to present a new alternative technique for surface-wave analysis of passive data (i.e., seismic sources not controlled by users). Our passive MASW technique uses two types of receiver arrays, 1D and 2D, for two different purposes. The 2D square array is used for assessing the number and directionality of passive seismic sources to help identify optimal time window(s) when such sources are of sufficient quality and aligned with the 1D receiver spread. Then, these time windows are used to selectively extract passive seismic data recorded by the 1D receiver spread for subsequent MASW analysis. In such a manner, this hybrid 1D–2D passive MASW approach can approximate the higher quality advantages of the active MASW method. This technique is successfully applied at a test site in southcentral Kansas taking advantage of train energy as the passive sources monitoring and assessing the potential development of vertically migrating voids that could endanger groundwater and infrastructure. The 1D–2D passive MASW method has proven beneficial for optimizing passive-data dispersion patterns and accurately assessing relative velocities for investigations with reduced labor costs and minimal added processing time and can be considered as a contribution to the surface-wave analysis tools.
- 1 May 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (3) , WA59-WA68
Shallow tunnel detection using converted surface waves
Seismic surface waves that were likely converted from incident body waves were used to detect a 3 m deep tunnel using two novel processing methods. In data acquired at a tunnel test site, a unique forward-propagating wave (traveling away from the tunnel and seismic source) was identified as an early-arriving surface wave converted at the tunnel from an incident body wave. To our knowledge, our research represents the first time converted surface waves have been observed originating from a tunnel. We have developed two novel processing methods targeting this unique wavefield component for detecting tunnels, cavities, or other shallow anomalies. The first is a time-domain imaging method that takes advantage of the unique kinematic characteristics of converted surface waves to produce a cross section with a coherent, high-amplitude signature originating from the horizontal location of the tunnel. The second method uses frequency-domain analysis of surface-wave amplitudes, which reveals increased amplitudes (primarily from converted surface waves) at locations expected for the tunnel. These proposed approaches for analysis of converted surface waves were successfully used to detect the tunnel and accurately interpret its horizontal location in real-world data. These novel methods could be the key for detecting shallow tunnels or other subsurface anomalies and complement existing seismic detection methods.
- 1 May 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (3) , WA59-WA68
Shallow tunnel detection using converted surface waves
Seismic surface waves that were likely converted from incident body waves were used to detect a 3 m deep tunnel using two novel processing methods. In data acquired at a tunnel test site, a unique forward-propagating wave (traveling away from the tunnel and seismic source) was identified as an early-arriving surface wave converted at the tunnel from an incident body wave. To our knowledge, our research represents the first time converted surface waves have been observed originating from a tunnel. We have developed two novel processing methods targeting this unique wavefield component for detecting tunnels, cavities, or other shallow anomalies. The first is a time-domain imaging method that takes advantage of the unique kinematic characteristics of converted surface waves to produce a cross section with a coherent, high-amplitude signature originating from the horizontal location of the tunnel. The second method uses frequency-domain analysis of surface-wave amplitudes, which reveals increased amplitudes (primarily from converted surface waves) at locations expected for the tunnel. These proposed approaches for analysis of converted surface waves were successfully used to detect the tunnel and accurately interpret its horizontal location in real-world data. These novel methods could be the key for detecting shallow tunnels or other subsurface anomalies and complement existing seismic detection methods.
- Open Access
- 26 April 2021
- Published by U.S. Army Engineer Research and Development Center
Detecting clandestine tunnels by using near-surface seismic techniques
- 26 April 2021
- Published by U.S. Army Engineer Research and Development Center
Open AccessDetecting clandestine tunnels by using near-surface seismic techniques
- Open Access
- 7 December 2020
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Solid Earth
- Vol. 125 (12)
Comment on “Accelerated Fill‐Up of the Arbuckle Group Aquifer and Links to U.S. Midcontinent Seismicity” by Ansari et al. (2019)
Spatiotemporal analysis of Arbuckle Group formation pressures and disposal volumes provides insight into contributing factors underlying the regional trends in formation pressure identified by Ansari et al. (2019, https://doi.org/10.1029/2018JB016926) using statistical analysis. Based on trends in bivariate correlation of reported values, Ansari et al. (2019) suggested that rising formation pressures were a result of fluid injection within 25 km. Our primary concern is that the correlation trends are most likely an artifact of the method used by Ansari et al. (2019), at least in part, and the conclusion that pressure diffusion is limited to within 25 km of the injection point does not necessarily follow from the analysis. We also note that estimated formation pressure depends on the depth of the pressure gauge, which, in some cases, varies from one measurement to the next and should be accounted for to accurately assess measured changes. The spatial relationship of formation pressure changes among wells provides valuable insight into the origin of those changes. For each well, we project pressure to a baseline depth to account for changes in gauge depth and reexamine trends in formation pressure. Spatiotemporal progression suggests post‐2011 formation pressure changes originate from a spatially dense group of high‐rate saltwater disposal wells near the Kansas‐Oklahoma border well beyond 25 km (and as far as 90 km) away.
- 7 December 2020
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Solid Earth
- Vol. 125 (12)
Open AccessComment on “Accelerated Fill‐Up of the Arbuckle Group Aquifer and Links to U.S. Midcontinent Seismicity” by Ansari et al. (2019)
Spatiotemporal analysis of Arbuckle Group formation pressures and disposal volumes provides insight into contributing factors underlying the regional trends in formation pressure identified by Ansari et al. (2019, https://doi.org/10.1029/2018JB016926) using statistical analysis. Based on trends in bivariate correlation of reported values, Ansari et al. (2019) suggested that rising formation pressures were a result of fluid injection within 25 km. Our primary concern is that the correlation trends are most likely an artifact of the method used by Ansari et al. (2019), at least in part, and the conclusion that pressure diffusion is limited to within 25 km of the injection point does not necessarily follow from the analysis. We also note that estimated formation pressure depends on the depth of the pressure gauge, which, in some cases, varies from one measurement to the next and should be accounted for to accurately assess measured changes. The spatial relationship of formation pressure changes among wells provides valuable insight into the origin of those changes. For each well, we project pressure to a baseline depth to account for changes in gauge depth and reexamine trends in formation pressure. Spatiotemporal progression suggests post‐2011 formation pressure changes originate from a spatially dense group of high‐rate saltwater disposal wells near the Kansas‐Oklahoma border well beyond 25 km (and as far as 90 km) away.
- 1 May 2020
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 39 (5) , 318-323
Time-lapse monitoring of stress-field variations within the Lower Permian shales in Kansas
Azimuthal stress-field variations in Permian shale overlying voids in salt appear related to localized void roof failure based on interpretations of time-lapse recordings of passive seismic surface-wave data. Salt-dissolution voids in south-central Kansas exist within the Hutchinson Salt Member as a result of solution mining operations early in the 20th century. Since shear-wave velocity can be estimated from surface-wave analysis and is directly related to the shear modulus, or material rigidity, it can be used to indicate shale cap-rock competency. Temporal bulk-velocity variations in bedrock acquired over a known void from 2013 to 2018 are consistent with cyclic stress-field behavior expected with repetitive localized failure within the shale cap rock. It was determined that roof failure and associated subsidence began prior to the 2013 surveys along a north–south failure plane with consistent progression from southwest to northeast until 2017. A low-velocity anomaly observed in 2014–2015 on both profiles indicated a load redistribution in the shale cap rock. This low-velocity region was gradually replaced by an increasing velocity field in subsequent years. These bulk-velocity variations are interpreted as representations of stoping, which occurs when overlying roof layers or sidewall segments progressively fail. As of 2018, the velocity trend in the affected area remained lower than the recorded baseline conditions, with no low-velocity anomalies observed since 2015. Shear-wave velocities are not likely to return to 2013 conditions due to loss of roof material and redistribution of load. Annual surveys will monitor for conditions consistent with the beginning of a stress buildup and roof collapse unless monitoring indicates a change in the subsurface that warrants invasive analysis or other actions.
- 1 May 2020
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 39 (5) , 318-323
Time-lapse monitoring of stress-field variations within the Lower Permian shales in Kansas
Azimuthal stress-field variations in Permian shale overlying voids in salt appear related to localized void roof failure based on interpretations of time-lapse recordings of passive seismic surface-wave data. Salt-dissolution voids in south-central Kansas exist within the Hutchinson Salt Member as a result of solution mining operations early in the 20th century. Since shear-wave velocity can be estimated from surface-wave analysis and is directly related to the shear modulus, or material rigidity, it can be used to indicate shale cap-rock competency. Temporal bulk-velocity variations in bedrock acquired over a known void from 2013 to 2018 are consistent with cyclic stress-field behavior expected with repetitive localized failure within the shale cap rock. It was determined that roof failure and associated subsidence began prior to the 2013 surveys along a north–south failure plane with consistent progression from southwest to northeast until 2017. A low-velocity anomaly observed in 2014–2015 on both profiles indicated a load redistribution in the shale cap rock. This low-velocity region was gradually replaced by an increasing velocity field in subsequent years. These bulk-velocity variations are interpreted as representations of stoping, which occurs when overlying roof layers or sidewall segments progressively fail. As of 2018, the velocity trend in the affected area remained lower than the recorded baseline conditions, with no low-velocity anomalies observed since 2015. Shear-wave velocities are not likely to return to 2013 conditions due to loss of roof material and redistribution of load. Annual surveys will monitor for conditions consistent with the beginning of a stress buildup and roof collapse unless monitoring indicates a change in the subsurface that warrants invasive analysis or other actions.
- 26 November 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (2) , EN29-EN37
Shallow tunnel detection using SH-wave diffraction imaging
Clandestine tunnels, used for drug or human trafficking and tactical operations, pose a security threat worldwide and remain elusive targets for detection with geophysical methods. P-wave diffraction imaging is an increasingly common technique for detecting subsurface discontinuities that are smaller than the seismic wavelength (such as faults, pinch outs, and small voids) and has been successfully used to detect shallow tunnels. P-wave diffractions from tunnels typically have very low signal-to-noise ratios and are therefore challenging wavefield components for imaging. Mode-specific amplitude characteristics of theoretical diffractions from a shallow tunnel were evaluated using 9C seismic modeling. Results indicate that SH-wave diffraction has the largest amplitude and coherent phase characteristics along the traveltime hyperbola, making it ideal for diffraction imaging. In real data acquired over a 9.2 m deep tunnel, amplitudes of SH-wave diffractions are 20 dB greater than P-wave diffractions. The tunnel signature on the P-wave diffraction section is of low amplitude relative to the background. The SH-wave diffraction section has a high-amplitude signal focused at the horizontal location and a traveltime consistent with the tunnel location, indicating that the SH-wave may be optimal for diffraction imaging to detect shallow tunnels.
- 26 November 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (2) , EN29-EN37
Shallow tunnel detection using SH-wave diffraction imaging
Clandestine tunnels, used for drug or human trafficking and tactical operations, pose a security threat worldwide and remain elusive targets for detection with geophysical methods. P-wave diffraction imaging is an increasingly common technique for detecting subsurface discontinuities that are smaller than the seismic wavelength (such as faults, pinch outs, and small voids) and has been successfully used to detect shallow tunnels. P-wave diffractions from tunnels typically have very low signal-to-noise ratios and are therefore challenging wavefield components for imaging. Mode-specific amplitude characteristics of theoretical diffractions from a shallow tunnel were evaluated using 9C seismic modeling. Results indicate that SH-wave diffraction has the largest amplitude and coherent phase characteristics along the traveltime hyperbola, making it ideal for diffraction imaging. In real data acquired over a 9.2 m deep tunnel, amplitudes of SH-wave diffractions are 20 dB greater than P-wave diffractions. The tunnel signature on the P-wave diffraction section is of low amplitude relative to the background. The SH-wave diffraction section has a high-amplitude signal focused at the horizontal location and a traveltime consistent with the tunnel location, indicating that the SH-wave may be optimal for diffraction imaging to detect shallow tunnels.
- 21 December 2018
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 84 (1) , B95-B108
Tunnel detection at Yuma Proving Ground, Arizona, USA — Part 2: 3D full-waveform inversion experiments
We apply time domain 3D elastic full-waveform inversion (FWI) to a known tunnel constructed 10 m below the surface with no distinguishing surface expressions. Multi-component inversion experiments that use an initial model estimated from surface wave methods suggest that vertical sources and the combination of vertical and longitudinal receivers result in the clearest image of the tunnel. We obtain an approximate 3D image of the tunnel using 24 vertical sources and 720 vertical and 720 longitudinal receivers. We find that increasing the number of vertical sources to 216 does not significantly improve the details of the tunnel. Further experimentation shows we can detect the tunnel using a reduced data-set of 6-10 vertical sources and 216 vertical sensors. In addition, calculating the VP/VS ratio helps to remove artifacts from the inverted model and highlights the location of the tunnel. We compare the 3D inversion results in this paper to the 2D FWI results for the same tunnel that are discussed in Part I of the companion paper. The variety of successful inversion experiments suggest that FWI is capable of imaging shallow tunnels in desert geologies.
- 21 December 2018
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 84 (1) , B95-B108
Tunnel detection at Yuma Proving Ground, Arizona, USA — Part 2: 3D full-waveform inversion experiments
We apply time domain 3D elastic full-waveform inversion (FWI) to a known tunnel constructed 10 m below the surface with no distinguishing surface expressions. Multi-component inversion experiments that use an initial model estimated from surface wave methods suggest that vertical sources and the combination of vertical and longitudinal receivers result in the clearest image of the tunnel. We obtain an approximate 3D image of the tunnel using 24 vertical sources and 720 vertical and 720 longitudinal receivers. We find that increasing the number of vertical sources to 216 does not significantly improve the details of the tunnel. Further experimentation shows we can detect the tunnel using a reduced data-set of 6-10 vertical sources and 216 vertical sensors. In addition, calculating the VP/VS ratio helps to remove artifacts from the inverted model and highlights the location of the tunnel. We compare the 3D inversion results in this paper to the 2D FWI results for the same tunnel that are discussed in Part I of the companion paper. The variety of successful inversion experiments suggest that FWI is capable of imaging shallow tunnels in desert geologies.
- 26 July 2018
- Published by Society of Exploration Geophysicists in Geophysics
- p. 1-53
A practical approach to seismic imaging of tunnels using 3D full-waveform inversion
We present a practical approach to seismic imaging of small (1-2m) tunnels using 3D elastic full-waveform inversion (FWI). A field data-set was collected by the Kansas Geological Survey at Yuma Proving Ground over an existing hand-dug, research tunnel constructed 10 m below the surface with no distinguishing surface expressions. Multi-component inversion experiments demonstrate that using vertical sources and combining the vertical and longitudinal receivers result in the clearest image of the tunnel. We obtain an approximate 3D image of the tunnel using 24 vertical sources and 720 vertical and 720 longitudinal receivers. We find that increasing the number of vertical sources to 216 does not significantly improve the details of the tunnel. Further experimentation shows we can detect the tunnel using a reduced data-set of 6-10 vertical sources and 216 vertical sensors. In addition, calculating the VP/VS ratio helps to remove artifacts from the inverted models and highlights the location of the tunnel. The variety of successful inversion experiments suggest that FWI is capable of imaging shallow tunnels in desert geologies.
- 26 July 2018
- Published by Society of Exploration Geophysicists in Geophysics
- p. 1-53
A practical approach to seismic imaging of tunnels using 3D full-waveform inversion
We present a practical approach to seismic imaging of small (1-2m) tunnels using 3D elastic full-waveform inversion (FWI). A field data-set was collected by the Kansas Geological Survey at Yuma Proving Ground over an existing hand-dug, research tunnel constructed 10 m below the surface with no distinguishing surface expressions. Multi-component inversion experiments demonstrate that using vertical sources and combining the vertical and longitudinal receivers result in the clearest image of the tunnel. We obtain an approximate 3D image of the tunnel using 24 vertical sources and 720 vertical and 720 longitudinal receivers. We find that increasing the number of vertical sources to 216 does not significantly improve the details of the tunnel. Further experimentation shows we can detect the tunnel using a reduced data-set of 6-10 vertical sources and 216 vertical sensors. In addition, calculating the VP/VS ratio helps to remove artifacts from the inverted models and highlights the location of the tunnel. The variety of successful inversion experiments suggest that FWI is capable of imaging shallow tunnels in desert geologies.
- Open Access
- 17 April 2018
- Published by American Geophysical Union (AGU) in Eos
- Vol. 99
Fluid Injection Wells Can Have a Wide Seismic Reach
High-volume fluid injection can cumulatively increase underground pore pressure and induce earthquakes in regions unexpectedly far from injection wells, recent Kansas studies show.
- 17 April 2018
- Published by American Geophysical Union (AGU) in Eos
- Vol. 99
Open AccessFluid Injection Wells Can Have a Wide Seismic Reach
High-volume fluid injection can cumulatively increase underground pore pressure and induce earthquakes in regions unexpectedly far from injection wells, recent Kansas studies show.