Jihad Furqani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jihad Furqani has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Akira Chiba
Institute of Science Tokyo
7 shared publications - Kyohei Kiyota
Institute of Science Tokyo
5 shared publications - Arwindra Rizqiawan
School of Electrical Engineering and Informatics, Institut Teknologi Bandung, Bandung, Indonesia
4 shared publications - Candra Adi Wiguna
Department of Electrical and Electronic Engineering, Tokyo Institute of Technology, Tokyo, Japan
3 shared publications Agus Purwadi
Department of Electrical Power Engineering, National Centre for Sustainable Transportation Technology, Bandung Institute of Technology, Bandung, Jawa Barat, Indonesia
2 shared publicationsArwindra Rizqiawan
School of Electrical Engineering and Informatics, Institut Teknologi Bandung, Bandung, Indonesia
2 shared publications
Latest Publications
- Open Access
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1248-1260
Improving efficiency of multi-phase cascaded DC-DC boost converters in discontinuous conduction mode suitable for renewable energy application
This study presents an improvement on the efficiency of a proposed multiphase cascaded DC-DC boost converter by employing discontinuous conduction mode(DCM) for its operation. The proposed multiphase cascaded DC-DC boost converter is characterized by high voltage gain and low input current ripple. This converter consists of two stages and is designed to connect a photovoltaic (PV)system to a DC microgrid bus. First, the loss equations for the converter are analyzed, then discontinuous conduction mode is applied to the first stage of the proposed converter by adjusting the second stage output current value, which represents grid load fluctuations. Subsequently, the efficiency of the proposed converter will be evaluated. Further, comparison with two operation modes, continuous conduction mode (CCM) and boundary conduction mode (BCM), is provided. To verify the proposed analysis and calculation, experiments are conducted by implementing the circuitry in a lab-scale prototype. The results show that by implementing DCM operation, the proposed converter achieves the high est efficiency of 92.2% at an output power of 120 W, while other modes achieve lower efficiencies as in CCM with 90.17% at an output power of 215.5 W. In the proposed converter, the dominant source of losses is attributed to the inductor, accounting for approximately 62% of the total losses in DCM. The operation of DCMhas demonstrated a substantial reduction in switching losses, leading to a notable increase in efficiency.
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1248-1260
Open AccessImproving efficiency of multi-phase cascaded DC-DC boost converters in discontinuous conduction mode suitable for renewable energy application
This study presents an improvement on the efficiency of a proposed multiphase cascaded DC-DC boost converter by employing discontinuous conduction mode(DCM) for its operation. The proposed multiphase cascaded DC-DC boost converter is characterized by high voltage gain and low input current ripple. This converter consists of two stages and is designed to connect a photovoltaic (PV)system to a DC microgrid bus. First, the loss equations for the converter are analyzed, then discontinuous conduction mode is applied to the first stage of the proposed converter by adjusting the second stage output current value, which represents grid load fluctuations. Subsequently, the efficiency of the proposed converter will be evaluated. Further, comparison with two operation modes, continuous conduction mode (CCM) and boundary conduction mode (BCM), is provided. To verify the proposed analysis and calculation, experiments are conducted by implementing the circuitry in a lab-scale prototype. The results show that by implementing DCM operation, the proposed converter achieves the high est efficiency of 92.2% at an output power of 120 W, while other modes achieve lower efficiencies as in CCM with 90.17% at an output power of 215.5 W. In the proposed converter, the dominant source of losses is attributed to the inductor, accounting for approximately 62% of the total losses in DCM. The operation of DCMhas demonstrated a substantial reduction in switching losses, leading to a notable increase in efficiency.
- Open Access
- 1 March 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (1) , 117-128
Control strategy comparison of the 8/6 switched reluctance motor in several inverter topologies
This paper proposes a control strategy for switched reluctance motors (SRMs) using the asymmetric half-bridge (AHB), shared switch, and Miller converter based on MATLAB/Simulink and TMS320F28379D. The control strategy implemented in this study involves the application of proportional-integral (PI) speed control with a pulse width modulation (PWM) switching method for each topology. By employing this control strategy, the system aims to regulate the speed of the motor and achieve the desired performance while ensuring efficient power utilization. The PI controller is utilized to adjust the motor's speed based on the error between the desired and actual speeds, enabling precise control. Additionally, the PWM switching method is employed to modulate the motor voltage, allowing for smooth and continuous speed adjustments. A thorough method for maximizing each topology's performance and raising the overall system efficiency is provided by this combination of control techniques. The detailed analysis and operation of each converter are presented in this paper. Simulation and experiment results show that AHB and shared switch have better performance than Miller. But the Miller converter needs the least number of switching components. Although the performance of the shared switch is equal to that of AHB, uses of this topology are limited to SRM with an even number of phases.
- 1 March 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (1) , 117-128
Open AccessControl strategy comparison of the 8/6 switched reluctance motor in several inverter topologies
This paper proposes a control strategy for switched reluctance motors (SRMs) using the asymmetric half-bridge (AHB), shared switch, and Miller converter based on MATLAB/Simulink and TMS320F28379D. The control strategy implemented in this study involves the application of proportional-integral (PI) speed control with a pulse width modulation (PWM) switching method for each topology. By employing this control strategy, the system aims to regulate the speed of the motor and achieve the desired performance while ensuring efficient power utilization. The PI controller is utilized to adjust the motor's speed based on the error between the desired and actual speeds, enabling precise control. Additionally, the PWM switching method is employed to modulate the motor voltage, allowing for smooth and continuous speed adjustments. A thorough method for maximizing each topology's performance and raising the overall system efficiency is provided by this combination of control techniques. The detailed analysis and operation of each converter are presented in this paper. Simulation and experiment results show that AHB and shared switch have better performance than Miller. But the Miller converter needs the least number of switching components. Although the performance of the shared switch is equal to that of AHB, uses of this topology are limited to SRM with an even number of phases.
- Open Access
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (2) , 1017-1030
Analysis of the effect of mutual inductance on reducing output current ripple of the modified DC-DC Cuk converter
DC-DC converters exhibiting minimal input and output ripple are extensively employed across a diverse range of applications. This paper presents a proposed modification to the DC-DC Cuk converter. The converter is developed by modifying a conventional Cuk DC-DC converter to exhibit boost characteristics. The DC-DC converters possess the capability to function as versatile units that can be employed in a multitude of applications, ranging from DC-DC conversion to DC-AC conversion (inversion). This paper presents a novel DC-DC converter design that aims to achieve reduced ripple in both input and output currents. By employing the principle of mutual inductance, it is possible to further mitigate the presence of ripple current. The analysis of the impact of mutual inductance on the output voltage and ripple current of the proposed converter has been conducted. The validity of the derived analytical method has been confirmed through both simulated and experimental investigations. The utilization of mutual inductance in the proposed modified Cuk converter has been demonstrated to result in reduced current ripple.
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (2) , 1017-1030
Open AccessAnalysis of the effect of mutual inductance on reducing output current ripple of the modified DC-DC Cuk converter
DC-DC converters exhibiting minimal input and output ripple are extensively employed across a diverse range of applications. This paper presents a proposed modification to the DC-DC Cuk converter. The converter is developed by modifying a conventional Cuk DC-DC converter to exhibit boost characteristics. The DC-DC converters possess the capability to function as versatile units that can be employed in a multitude of applications, ranging from DC-DC conversion to DC-AC conversion (inversion). This paper presents a novel DC-DC converter design that aims to achieve reduced ripple in both input and output currents. By employing the principle of mutual inductance, it is possible to further mitigate the presence of ripple current. The analysis of the impact of mutual inductance on the output voltage and ripple current of the proposed converter has been conducted. The validity of the derived analytical method has been confirmed through both simulated and experimental investigations. The utilization of mutual inductance in the proposed modified Cuk converter has been demonstrated to result in reduced current ripple.
- Open Access
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (2) , 978-992
A bidirectional power converter connecting electric vehicle battery and DC microgrid
One way to increase electric vehicle (EV) battery utilization is to connect it to a dc microgrid. The EV battery can assume the role of an energy storage from the grid point of view. A bidirectional DC-DC converter will be needed to transfer power between them back and forth. This paper proposes the converter design considering its functional objective, including interleaved phase number determination. Efficiency performance evaluation is presented by power loss analysis with the parasitic-parameters consideration of the components. Finding optimum switching frequency based on power loss analysis is performed independently between input and output sides of the converter. Finally, experiments using a scaled-down prototype are shown to verify the analytical analysis of the converter. The experimental results properly validate the power loss analytic analysis carried out in this paper with a maximum error of 2.04% at 1131-watt, 60 V battery voltage, and 140 V grid voltage. Maximum efficiency 96.97% is obtained at 301-watt, 130 V battery voltage, and 151 V grid voltage. Overall, the converter has a simple structure, capable to be operated in various levels of input and output voltages with a minimum battery side current ripple.
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 15 (2) , 978-992
Open AccessA bidirectional power converter connecting electric vehicle battery and DC microgrid
One way to increase electric vehicle (EV) battery utilization is to connect it to a dc microgrid. The EV battery can assume the role of an energy storage from the grid point of view. A bidirectional DC-DC converter will be needed to transfer power between them back and forth. This paper proposes the converter design considering its functional objective, including interleaved phase number determination. Efficiency performance evaluation is presented by power loss analysis with the parasitic-parameters consideration of the components. Finding optimum switching frequency based on power loss analysis is performed independently between input and output sides of the converter. Finally, experiments using a scaled-down prototype are shown to verify the analytical analysis of the converter. The experimental results properly validate the power loss analytic analysis carried out in this paper with a maximum error of 2.04% at 1131-watt, 60 V battery voltage, and 140 V grid voltage. Maximum efficiency 96.97% is obtained at 301-watt, 130 V battery voltage, and 151 V grid voltage. Overall, the converter has a simple structure, capable to be operated in various levels of input and output voltages with a minimum battery side current ripple.
- Open Access
- 16 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 4, 23-34
Vibration and Acoustic Noise Reduction in Switched Reluctance Motor by Selective Radial Force Harmonics Reduction
This paper presents a novel method for vibration and acoustic noise reduction in a three-phase 6/10 switched reluctance motor. The test machine has major vibration and acoustic noise at the 2 nd , 4 th , 5 th , 7 th , and 8 th harmonics. Accordingly, a novel method called “selectiveradial force harmonic reduction”is proposed. The proposed method selectively reduces the specific radial force harmonicsatthe statorteeth.By reducing the specific radial forceharmonics such as 2 nd ,4 th ,5 th ,7 th ,and 8 th ,thecorresponding vibration and acoustic noise can be reduced significantly in the test machine. In this study, a current calculation for the proposed method is introduced. In addition, finite element analysis and experiments are conducted to verify the effectiveness of the proposed method. Compared with a conventional square current, the experimental results show that the overall sound pressure level is reduced by 7.1 dBA using the proposed method at the rated speed and torque. The dynamic conditions of the test machine using the proposed method are also presented. As a result, the proposed method is effective in reducing vibration and acoustic noise in the three-phase 6/10 switched reluctance motor.
- 16 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 4, 23-34
Open AccessVibration and Acoustic Noise Reduction in Switched Reluctance Motor by Selective Radial Force Harmonics Reduction
This paper presents a novel method for vibration and acoustic noise reduction in a three-phase 6/10 switched reluctance motor. The test machine has major vibration and acoustic noise at the 2 nd , 4 th , 5 th , 7 th , and 8 th harmonics. Accordingly, a novel method called “selectiveradial force harmonic reduction”is proposed. The proposed method selectively reduces the specific radial force harmonicsatthe statorteeth.By reducing the specific radial forceharmonics such as 2 nd ,4 th ,5 th ,7 th ,and 8 th ,thecorresponding vibration and acoustic noise can be reduced significantly in the test machine. In this study, a current calculation for the proposed method is introduced. In addition, finite element analysis and experiments are conducted to verify the effectiveness of the proposed method. Compared with a conventional square current, the experimental results show that the overall sound pressure level is reduced by 7.1 dBA using the proposed method at the rated speed and torque. The dynamic conditions of the test machine using the proposed method are also presented. As a result, the proposed method is effective in reducing vibration and acoustic noise in the three-phase 6/10 switched reluctance motor.
- 20 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (5) , 6332-6342
A Novel Method to Reduce Low-Frequency Output Current Ripple of PWM Inverters
The output current of PWM inverters may contain low-frequency harmonics due to nonidealities, such as fluctuating dc voltage and dead-time. Low-frequency harmonics are detrimental to the inverter's current controller performance as well as its operation. They increase losses, cause synchronization problems in a grid-connected inverter, and cause torque pulsations in motors. Reducing low-frequency harmonics through conventional means require a big and expensive filter. In this article, a method to reduce low-frequency current harmonics is proposed. This method uses a virtual impedance, which is a controller block that mimics the behavior of a real impedance. Because it is virtual, it does not have physical drawbacks to the system, such as volume, weight, and losses. It can be designed only to affect the disturbance signals and to assume characteristics unlike a real impedance. It can also be added as a plug-in block to an already existing controller, saving a significant amount of design effort. Simulation and experimental results show a decrease of current THD to almost 1/3 of the original THD when no virtual impedance is used, demonstrating the effectiveness of the proposed method.
- 20 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (5) , 6332-6342
A Novel Method to Reduce Low-Frequency Output Current Ripple of PWM Inverters
The output current of PWM inverters may contain low-frequency harmonics due to nonidealities, such as fluctuating dc voltage and dead-time. Low-frequency harmonics are detrimental to the inverter's current controller performance as well as its operation. They increase losses, cause synchronization problems in a grid-connected inverter, and cause torque pulsations in motors. Reducing low-frequency harmonics through conventional means require a big and expensive filter. In this article, a method to reduce low-frequency current harmonics is proposed. This method uses a virtual impedance, which is a controller block that mimics the behavior of a real impedance. Because it is virtual, it does not have physical drawbacks to the system, such as volume, weight, and losses. It can be designed only to affect the disturbance signals and to assume characteristics unlike a real impedance. It can also be added as a plug-in block to an already existing controller, saving a significant amount of design effort. Simulation and experimental results show a decrease of current THD to almost 1/3 of the original THD when no virtual impedance is used, demonstrating the effectiveness of the proposed method.
- Open Access
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 162359-162369
Improving Inverter Output Current Controller Under Unbalanced Conditions by Using Virtual Impedance
Nowadays, three-phase inverters have been commonly used in power systems, especially in renewable energy and motor drives applications. In many applications, the inverter has to generate balanced sinusoidal three-phase currents even though it is connected to an unbalanced system. Methods to suppress unbalanced currents commonly use decomposition of the unbalanced currents to their positive and negative sequence components. Thus, the positive and negative sequence currents can be controlled separately. However, this method is complicated because of the existence of sequence transformation block, a lot of signals to be controlled, and affect the transient response significantly. This paper proposes a novel method with detailed analysis to balance the inverter output currents under unbalanced AC side conditions without sequence transformation and affecting the transient response. The proposed method is based on virtual impedance concept that is inserted in series to the inverter output. The proposed virtual impedance is an additional control algorithm that changes the inverter behaviour into the one that has a real impedance connected to it. As it is virtual, the virtual impedance can be designed in such a way so that just the unbalanced signal is affected. Because there is no sequence transformation, the positive and negative sequence currents are not controlled separately. Simulation and experiment results show the effectiveness of the proposed method to suppress 12.13% current unbalance to only 2.27%. Meanwhile, the result is also compared to the conventional dual-reference method, proving the proposed method does not affect the transient response of the current reference.
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 162359-162369
Open AccessImproving Inverter Output Current Controller Under Unbalanced Conditions by Using Virtual Impedance
Nowadays, three-phase inverters have been commonly used in power systems, especially in renewable energy and motor drives applications. In many applications, the inverter has to generate balanced sinusoidal three-phase currents even though it is connected to an unbalanced system. Methods to suppress unbalanced currents commonly use decomposition of the unbalanced currents to their positive and negative sequence components. Thus, the positive and negative sequence currents can be controlled separately. However, this method is complicated because of the existence of sequence transformation block, a lot of signals to be controlled, and affect the transient response significantly. This paper proposes a novel method with detailed analysis to balance the inverter output currents under unbalanced AC side conditions without sequence transformation and affecting the transient response. The proposed method is based on virtual impedance concept that is inserted in series to the inverter output. The proposed virtual impedance is an additional control algorithm that changes the inverter behaviour into the one that has a real impedance connected to it. As it is virtual, the virtual impedance can be designed in such a way so that just the unbalanced signal is affected. Because there is no sequence transformation, the positive and negative sequence currents are not controlled separately. Simulation and experiment results show the effectiveness of the proposed method to suppress 12.13% current unbalance to only 2.27%. Meanwhile, the result is also compared to the conventional dual-reference method, proving the proposed method does not affect the transient response of the current reference.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (5) , 4707-4719
Improved Current Profile Selection for Noise Reduction of Switched Reluctance Motor at Middle Speed Considering Back EMF
An improved current profile selection for noise reduction of a switched reluctance motor during middle-speed operation is presented with the principle of flattening the three-phase radial force sum. The improved current is selected from the proposed algorithm, which considers the limited input voltage and back electromotive force influence at middle-speed operation. The improved current profile is compared with the single pulse current, which is the typical current for switched reluctance motors at middle-speed operation. The analysis results show that the variation of the radial force sum by the improved current profile is less than that of the single pulse current, although the influence of the back electromotive force is high. The effectiveness of radial force sum flattening is verified by the experimental results. The experiments were carried out with the downscaled operating point of a switched reluctance motor owing to the limited range of the operating speed. The experiment results show a significant reduction in the highest and second-highest peak noises at 5.4 kHz and 1.8 kHz by 11.04 dB and 17.51 dB, respectively with the improved current profile. The other noises were also reduced.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (5) , 4707-4719
Improved Current Profile Selection for Noise Reduction of Switched Reluctance Motor at Middle Speed Considering Back EMF
An improved current profile selection for noise reduction of a switched reluctance motor during middle-speed operation is presented with the principle of flattening the three-phase radial force sum. The improved current is selected from the proposed algorithm, which considers the limited input voltage and back electromotive force influence at middle-speed operation. The improved current profile is compared with the single pulse current, which is the typical current for switched reluctance motors at middle-speed operation. The analysis results show that the variation of the radial force sum by the improved current profile is less than that of the single pulse current, although the influence of the back electromotive force is high. The effectiveness of radial force sum flattening is verified by the experimental results. The experiments were carried out with the downscaled operating point of a switched reluctance motor owing to the limited range of the operating speed. The experiment results show a significant reduction in the highest and second-highest peak noises at 5.4 kHz and 1.8 kHz by 11.04 dB and 17.51 dB, respectively with the improved current profile. The other noises were also reduced.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (3) , 2481-2493
Experimental Verification of Acoustic Noise and Radial Force Sum Variation in Switched Reluctance Motor
Acoustic noise reduction is one of the main topics of switched reluctance motor (SRM) developments. One of the effective methods is flattening three-phase radial force sum. This method is verified in experiments by optimizing the current profile. Novel current waveforms have been proposed recently for acoustic noise reduction without sacrificing the efficiency in the 18/12 SRM, which has competitive power density, torque density, peak efficiency, and outer dimensions compared with the permanent magnet motor employed in hybrid electric vehicles. In this article, electro-mechanical analysis and acoustic analysis are carried out to verify acoustic noise reduction in the 18/12 SRM. The relationship between radial force sum F rsum , torque ripple T rip , and acoustic noise is investigated. Experimental confirmation is also included.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (3) , 2481-2493
Experimental Verification of Acoustic Noise and Radial Force Sum Variation in Switched Reluctance Motor
Acoustic noise reduction is one of the main topics of switched reluctance motor (SRM) developments. One of the effective methods is flattening three-phase radial force sum. This method is verified in experiments by optimizing the current profile. Novel current waveforms have been proposed recently for acoustic noise reduction without sacrificing the efficiency in the 18/12 SRM, which has competitive power density, torque density, peak efficiency, and outer dimensions compared with the permanent magnet motor employed in hybrid electric vehicles. In this article, electro-mechanical analysis and acoustic analysis are carried out to verify acoustic noise reduction in the 18/12 SRM. The relationship between radial force sum F rsum , torque ripple T rip , and acoustic noise is investigated. Experimental confirmation is also included.
- 11 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (4) , 3617-3629
Current Reference Selection for Acoustic Noise Reduction in Two Switched Reluctance Motors by Flattening Radial Force Sum
In this paper, a selection of a few current references for acoustic noise reduction in the 36–24 and the 18–12 switched reluctance motors is presented. It is seen that the difference in radial force profile results in few optimal current references. It is found that the optimal current reference with extreme radial force sum flattening results in increased rms current and loss in a magnetically saturated region of the 18–12 SRM. Thus, proper selection of the current references is necessary. Analysis, simulation, and experimental results are presented with the conventional and optimal currents to verify the effectiveness of flattening radial force sum method in acoustic noise reduction. It is shown that effective acoustic noise reduction and efficiency improvement are confirmed with proposed current reference selection.
- 11 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (4) , 3617-3629
Current Reference Selection for Acoustic Noise Reduction in Two Switched Reluctance Motors by Flattening Radial Force Sum
In this paper, a selection of a few current references for acoustic noise reduction in the 36–24 and the 18–12 switched reluctance motors is presented. It is seen that the difference in radial force profile results in few optimal current references. It is found that the optimal current reference with extreme radial force sum flattening results in increased rms current and loss in a magnetically saturated region of the 18–12 SRM. Thus, proper selection of the current references is necessary. Analysis, simulation, and experimental results are presented with the conventional and optimal currents to verify the effectiveness of flattening radial force sum method in acoustic noise reduction. It is shown that effective acoustic noise reduction and efficiency improvement are confirmed with proposed current reference selection.