Lars Ohlsson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lars Ohlsson has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Lars-Erik Wernersson
Lund University
28 shared publications - Erik Lind
Lund University
10 shared publications Mikael Egard
Department of Electrical and Information Technology, Lund University, Lund, Sweden
7 shared publications- Daniel Sjoberg
Department of Electrical and Information Technology, Lund University, Lund, Sweden
5 shared publications - Anette Löfstrand
Department of Electrical and Information Technology, Lund University, Lund, Sweden
3 shared publications - Gautham Rangasamy
Department of Electrical and Information Technology, Lund University, Lund, Sweden
3 shared publications
Latest Publications
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1392-1395
Impact of Layout on the RF Performance of Vertical In–Ga–As Nanowire MOSFETs
High-speed vertical In–Ga–As nanowire MOS field-effect transistor (MOSFET) measurements were analyzed through parametric layout models. Measurements from small and large transistors were used to fit dependencies on the number of gate fingers and the number of wires per finger. Extrapolations via intrinsic and parasitic elements reveal the optimal layout for peak frequency performance. To achieve a scalable technology platform, the process flow was here also reworked and simplified. In conjunction with refined feeder patterning, addition of a drain spacer, and reduced gate lengths previously demonstrated, the results indicate a viable path for strongly improved frequency performance in the technology.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1392-1395
Impact of Layout on the RF Performance of Vertical In–Ga–As Nanowire MOSFETs
High-speed vertical In–Ga–As nanowire MOS field-effect transistor (MOSFET) measurements were analyzed through parametric layout models. Measurements from small and large transistors were used to fit dependencies on the number of gate fingers and the number of wires per finger. Extrapolations via intrinsic and parasitic elements reveal the optimal layout for peak frequency performance. To achieve a scalable technology platform, the process flow was here also reworked and simplified. In conjunction with refined feeder patterning, addition of a drain spacer, and reduced gate lengths previously demonstrated, the results indicate a viable path for strongly improved frequency performance in the technology.
- Open Access
- 18 February 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (21)
Gate Layout and Process Reliability Co‐Optimization in High‐Speed Vertical III–V Nanowire Metal‐Oxide‐Semiconductor Field‐Effect Transistor Technology
High‐speed vertical III–V nanowire transistors utilize their channel material for high frequency and low noise performance. A device layout revision to optimize gate resistance, in a trade‐off to gate‐source capacitance, is presented. A two‐step redesign of the established device layout is proposed. First step is demonstrated with fabricated structures. The second step predicts the design transition from double row gate fingers to wider array structures, motivated by numerical simulations. Distributed radio frequency modeling is used to assess the resulting input parasitic elements of the transistor. These design alterations also yield a potential for improved device process reliability. In parallel, this study analyzes sputtered tungsten used as the gate metal, focusing on measurements of its resistivity and variations in stress properties from different deposition conditions, thereby allowing further improved process reliability. It is found that 60 nanometer tungsten gate on a gate stack capped by a thin titanium nitride shows shifted stress properties compared to the same film deposited directly on the gate oxide. This work promises improved high‐speed process reliability as well as reduction of external gate parasitic elements by more than a factor of 2, what leads to increased gain and reduced noise figure at a given operating frequency.
- 18 February 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (21)
Open AccessGate Layout and Process Reliability Co‐Optimization in High‐Speed Vertical III–V Nanowire Metal‐Oxide‐Semiconductor Field‐Effect Transistor Technology
High‐speed vertical III–V nanowire transistors utilize their channel material for high frequency and low noise performance. A device layout revision to optimize gate resistance, in a trade‐off to gate‐source capacitance, is presented. A two‐step redesign of the established device layout is proposed. First step is demonstrated with fabricated structures. The second step predicts the design transition from double row gate fingers to wider array structures, motivated by numerical simulations. Distributed radio frequency modeling is used to assess the resulting input parasitic elements of the transistor. These design alterations also yield a potential for improved device process reliability. In parallel, this study analyzes sputtered tungsten used as the gate metal, focusing on measurements of its resistivity and variations in stress properties from different deposition conditions, thereby allowing further improved process reliability. It is found that 60 nanometer tungsten gate on a gate stack capped by a thin titanium nitride shows shifted stress properties compared to the same film deposited directly on the gate oxide. This work promises improved high‐speed process reliability as well as reduction of external gate parasitic elements by more than a factor of 2, what leads to increased gain and reduced noise figure at a given operating frequency.
- 27 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 560-563
Scalable Vertical In–Ga–As Nanowire MOSFET With 67 mV/dec at 126μm Gate Width
Heterogeneous integration of III-V narrow bandgap transistors on silicon technology is desirable for high frequency circuit implementations. Such high-speed transistors must, however, scale to large gate widths to be suitable for general circuit design. Averaging among many variable channels is a key challenge for nanowire devices. A simplified, but high-speed compatible, nanowire device process was developed here. It utilizes metal plugs to reduce complexity in the gate patterning step. It also implements a spin coated BCB low-k dielectric as top interlayer. A vertical In-Ga–As MOSFET with 1600 nanowire channels and 110 nm gate length achieved a minimum subthreshold swing of $\mathrm {67~\mathrm{mV/dec} }$ at $\mathrm {126~\mu \text {m} }$ gate width. The maximum transconductance was $\mathrm {0.88~\text {m}\text {S} /\mu \text {m}}$ at 0.5 V drain-source voltage, with $\mathrm {0.22~\text {m}\text {A} /\mu \text {m}}$ normalized drain current. These long-channel results are on par with state-of-the art, but achieved for a device scaled to unprecedented device width. In tandem with the BCB interlayer, these results promise a back-end-of-line compatible high-speed vertical nanowire technology for integration on silicon.
- 27 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 560-563
Scalable Vertical In–Ga–As Nanowire MOSFET With 67 mV/dec at 126μm Gate Width
Heterogeneous integration of III-V narrow bandgap transistors on silicon technology is desirable for high frequency circuit implementations. Such high-speed transistors must, however, scale to large gate widths to be suitable for general circuit design. Averaging among many variable channels is a key challenge for nanowire devices. A simplified, but high-speed compatible, nanowire device process was developed here. It utilizes metal plugs to reduce complexity in the gate patterning step. It also implements a spin coated BCB low-k dielectric as top interlayer. A vertical In-Ga–As MOSFET with 1600 nanowire channels and 110 nm gate length achieved a minimum subthreshold swing of $\mathrm {67~\mathrm{mV/dec} }$ at $\mathrm {126~\mu \text {m} }$ gate width. The maximum transconductance was $\mathrm {0.88~\text {m}\text {S} /\mu \text {m}}$ at 0.5 V drain-source voltage, with $\mathrm {0.22~\text {m}\text {A} /\mu \text {m}}$ normalized drain current. These long-channel results are on par with state-of-the art, but achieved for a device scaled to unprecedented device width. In tandem with the BCB interlayer, these results promise a back-end-of-line compatible high-speed vertical nanowire technology for integration on silicon.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (9) , 1653-1656
RF Characterization of Ferroelectric MOS Capacitors
The high-frequency capacitive and switching response of ferroelectric Hf0.5Zr0.5O2 (HZO) is investigated on scaled ferroelectric metal-oxide-semiconductor III-V capacitors. Spanning over six orders of magnitude, the measured frequency response allows for accurate modeling of the capacitance-frequency dispersion. The steady-state ferroelectric behavior is retained even in the mm-wave frequency range and provides a 25% capacitive tunability, demonstrating its applicability as a non-volatile reconfigurable varactor. The measured film reconfigurability is in the nanosecond time-regime, mainly limited by the measurement setup.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (9) , 1653-1656
RF Characterization of Ferroelectric MOS Capacitors
The high-frequency capacitive and switching response of ferroelectric Hf0.5Zr0.5O2 (HZO) is investigated on scaled ferroelectric metal-oxide-semiconductor III-V capacitors. Spanning over six orders of magnitude, the measured frequency response allows for accurate modeling of the capacitance-frequency dispersion. The steady-state ferroelectric behavior is retained even in the mm-wave frequency range and provides a 25% capacitive tunability, demonstrating its applicability as a non-volatile reconfigurable varactor. The measured film reconfigurability is in the nanosecond time-regime, mainly limited by the measurement setup.
- 30 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 23 (1536125X) , 441-447
TFET Circuit Configurations Operating Below 60 mV/dec
Tunnel Field-Effect Transistors (TFETs) offer more energy efficient alternative to CMOS for design of low power circuits. In spite of this potential, circuits based on TFETs have not been experimentally demonstrated so far. In this letter, we explore TFET fabrication and basic functionality of n-TFET based circuits in the following configurations: a current mirror, a diode-connected inverter, and a cascode. Individual TFETs in the circuit operate well below 60 mV/dec operation with minimum achieved subthreshold swing (SS) of 30 mV/dec at drain voltage of 400 mV. To analyse the circuit operation, individual devices are connected via FEOL and are biased at 300 mV supply voltage, with an input frequency of 200 kHz. The measured circuit configurations demonstrate the expected functionality.
- 30 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 23 (1536125X) , 441-447
TFET Circuit Configurations Operating Below 60 mV/dec
Tunnel Field-Effect Transistors (TFETs) offer more energy efficient alternative to CMOS for design of low power circuits. In spite of this potential, circuits based on TFETs have not been experimentally demonstrated so far. In this letter, we explore TFET fabrication and basic functionality of n-TFET based circuits in the following configurations: a current mirror, a diode-connected inverter, and a cascode. Individual TFETs in the circuit operate well below 60 mV/dec operation with minimum achieved subthreshold swing (SS) of 30 mV/dec at drain voltage of 400 mV. To analyse the circuit operation, individual devices are connected via FEOL and are biased at 300 mV supply voltage, with an input frequency of 200 kHz. The measured circuit configurations demonstrate the expected functionality.
- Open Access
- 18 September 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (18)
gm/Id$g_m/I_d$ Analysis of vertical nanowire III–V TFETs
Experimental data on analog performance of gate‐all‐around III‐V vertical Tunnel Field‐Effect Transistors (TFETs) and circuits are presented. The individual device shows a minimal subthreshold swing of 44 mV/dec and transconductance efficiency of 50 V −1 for current range of 9 nA/μm to 100 nA/μm and at a drain voltage of 100 mV. This TFET demonstrates translinearity between transconductance and drain current for over a decade of current, paving way for low power current‐mode analog IC design. To explore this design principle, a current conveyor circuit is implemented, which exhibits large‐signal voltage gain of 0.89 mV/mV, current gain of 1nA/nA and an operating frequency of 320 kHz. Furthermore, at higher drain bias of 500 mV, the device shows maximum transconductance of 72 μS/μm and maximum drain current of 26 μA/μm. The device, thereby, can be operated as a current mode device at lower bias voltage and as voltage mode device at higher bias voltage.
- 18 September 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (18)
Open Accessgm/Id$g_m/I_d$ Analysis of vertical nanowire III–V TFETs
Experimental data on analog performance of gate‐all‐around III‐V vertical Tunnel Field‐Effect Transistors (TFETs) and circuits are presented. The individual device shows a minimal subthreshold swing of 44 mV/dec and transconductance efficiency of 50 V −1 for current range of 9 nA/μm to 100 nA/μm and at a drain voltage of 100 mV. This TFET demonstrates translinearity between transconductance and drain current for over a decade of current, paving way for low power current‐mode analog IC design. To explore this design principle, a current conveyor circuit is implemented, which exhibits large‐signal voltage gain of 0.89 mV/mV, current gain of 1nA/nA and an operating frequency of 320 kHz. Furthermore, at higher drain bias of 500 mV, the device shows maximum transconductance of 72 μS/μm and maximum drain current of 26 μA/μm. The device, thereby, can be operated as a current mode device at lower bias voltage and as voltage mode device at higher bias voltage.
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1212-1215
Self-Heating in Gate-All-Around Vertical III-V InAs/InGaAs MOSFETs
We investigate self-heating in vertical, gate-all-around III-V InAs/InGaAs nanowire MOSFETs using pulsed IV measurements at various temperatures. Low temperature measurements reveal a negative output conductance indicating self-heating in the transistor. Under pulsed measurements, an increase in drain current (15%) and transconductance (30%) are observed at room temperature, with values influenced by the pulse width. This effect on performance is quantified with determination of the thermal resistance and capacitance. Furthermore, a first order thermal circuit is modelled based on the thermal impedances. The results indicate that the intrinsic temperature rises to 385 K when the device is operated in DC at room temperature (300 K) with a thermal time constant of 1 μs. We find that self-heating is a limiting factor for device performance.
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1212-1215
Self-Heating in Gate-All-Around Vertical III-V InAs/InGaAs MOSFETs
We investigate self-heating in vertical, gate-all-around III-V InAs/InGaAs nanowire MOSFETs using pulsed IV measurements at various temperatures. Low temperature measurements reveal a negative output conductance indicating self-heating in the transistor. Under pulsed measurements, an increase in drain current (15%) and transconductance (30%) are observed at room temperature, with values influenced by the pulse width. This effect on performance is quantified with determination of the thermal resistance and capacitance. Furthermore, a first order thermal circuit is modelled based on the thermal impedances. The results indicate that the intrinsic temperature rises to 385 K when the device is operated in DC at room temperature (300 K) with a thermal time constant of 1 μs. We find that self-heating is a limiting factor for device performance.
- 9 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (2) , 1284-1291
Lateral III–V Nanowire MOSFETs in Low-Noise Amplifier Stages
Lateral III–V nanowire (NW) MOSFETs are a promising candidate for high-frequency electronics. However, their circuit performance is not yet assessed. Here, we integrate lateral nanowires (LNWs) in a circuit environment and characterize the transistors and amplifiers. MOSFETs are fabricated in a simple scheme with a dc transconductance of up to 1.3 mS/ $\mu \text{m}$ , ON-resistance down to $265 \Omega \cdot \mu \text{m}$ , and cutoff frequencies up to 250 GHz, measured on the circuit level. The circuit model estimates 25% device parasitic capacitance increase due to back-end-of-line (BEOL) dielectric cladding. A low-noise amplifier input stage is designed with optimum network design for a noise matched input and an inductive peaking output. The input stage shows up to 4-dB gain and 2.5-dB noise figure (NF), at 60 GHz. Utilizing gate-length scaling in the circuit environment, the obtained normalized intrinsic gate capacitance value of 0.34-aF/nm gate length, per NW, corresponds well to the predicted theoretical value, demonstrating the circuit’s ability to provide intrinsic device parameters. This is the first mm-wave validation of noise models for III–V LNW MOSFETs. The results demonstrate the potential for utilization of the technology platform for low-noise applications.
- 9 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (2) , 1284-1291
Lateral III–V Nanowire MOSFETs in Low-Noise Amplifier Stages
Lateral III–V nanowire (NW) MOSFETs are a promising candidate for high-frequency electronics. However, their circuit performance is not yet assessed. Here, we integrate lateral nanowires (LNWs) in a circuit environment and characterize the transistors and amplifiers. MOSFETs are fabricated in a simple scheme with a dc transconductance of up to 1.3 mS/ $\mu \text{m}$ , ON-resistance down to $265 \Omega \cdot \mu \text{m}$ , and cutoff frequencies up to 250 GHz, measured on the circuit level. The circuit model estimates 25% device parasitic capacitance increase due to back-end-of-line (BEOL) dielectric cladding. A low-noise amplifier input stage is designed with optimum network design for a noise matched input and an inductive peaking output. The input stage shows up to 4-dB gain and 2.5-dB noise figure (NF), at 60 GHz. Utilizing gate-length scaling in the circuit environment, the obtained normalized intrinsic gate capacitance value of 0.34-aF/nm gate length, per NW, corresponds well to the predicted theoretical value, demonstrating the circuit’s ability to provide intrinsic device parameters. This is the first mm-wave validation of noise models for III–V LNW MOSFETs. The results demonstrate the potential for utilization of the technology platform for low-noise applications.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 20 (1536125X) , 434-440
Millimeter-Wave Vertical III-V Nanowire MOSFET Device-to-Circuit Co-Design
Vertical III-V nanowire MOSFETs show potential towards the ultimate transistor scaling. A high transconductance and current density are achieved based on the gate-all-around architecture. This work presents a high-frequency design of such devices, achieving more than 600 GHz cut-off frequencies (f T , f max ), at 20 nm gate length. Furthermore, capacitance design and scaling trends, supported by COMSOL Multiphysics simulations derive state-of-the-art parasitics magnitudes for vertical devices in general, reaching gate-drain capacitance values of 17 aF/wire, corresponding to 0.2 fF/μm. A unique co-designed feedback resonant circuit makes the device unilateral, exhibiting up to 15 dB gain in D-band at 0.5 V supply, and with a current density of 0.5 mA/μm. Finally, a 2-stage low noise amplifier is designed using an optimum matching concept to utilize the full available bandwidth. The resulting circuit performance is independent of transistor gate length, since any decrease in device intrinsic capacitance is assisted by an increase in device overlap capacitances in a setting unique to a current implementation of vertical nanowire MOSFETs. With this approach, amplifiers are designed with more than 20 dB gain and minimum noise figure of 2.5 dB in a simulation environment at 140 GHz. The proposed technology and design platform show a great potential in future low-power communication systems.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 20 (1536125X) , 434-440
Millimeter-Wave Vertical III-V Nanowire MOSFET Device-to-Circuit Co-Design
Vertical III-V nanowire MOSFETs show potential towards the ultimate transistor scaling. A high transconductance and current density are achieved based on the gate-all-around architecture. This work presents a high-frequency design of such devices, achieving more than 600 GHz cut-off frequencies (f T , f max ), at 20 nm gate length. Furthermore, capacitance design and scaling trends, supported by COMSOL Multiphysics simulations derive state-of-the-art parasitics magnitudes for vertical devices in general, reaching gate-drain capacitance values of 17 aF/wire, corresponding to 0.2 fF/μm. A unique co-designed feedback resonant circuit makes the device unilateral, exhibiting up to 15 dB gain in D-band at 0.5 V supply, and with a current density of 0.5 mA/μm. Finally, a 2-stage low noise amplifier is designed using an optimum matching concept to utilize the full available bandwidth. The resulting circuit performance is independent of transistor gate length, since any decrease in device intrinsic capacitance is assisted by an increase in device overlap capacitances in a setting unique to a current implementation of vertical nanowire MOSFETs. With this approach, amplifiers are designed with more than 20 dB gain and minimum noise figure of 2.5 dB in a simulation environment at 140 GHz. The proposed technology and design platform show a great potential in future low-power communication systems.
- 12 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (12) , 1-4
Pulsed Millimeter Wave Radar for Hand Gesture Sensing and Classification
A pulsed millimeter wave radar operating at a frame rate of 144 Hz is utilized to record 2160 scattering signatures of twelve generic hand gestures. Gesture recognition is achieved by machine learning, utilizing transfer learning on a pre-trained convolutional neural network. This yields excellent classification results with a validation accuracy of 99.5%, based on a 60% training vs. 40% validation split. The corresponding confusion matrix is also presented, showing a high level of classification orthogonality between the tested gestures. This is the first demonstration where data from a pulsed millimeter wave radar is used for gesture recognition by machine learning. It proves that the range-time envelope representation of high frame-rate data from a pulsed radar is suitable for hand gesture recognition. Further improvements are expected for more complex detection schemes and tailored neural networks.
- 12 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (12) , 1-4
Pulsed Millimeter Wave Radar for Hand Gesture Sensing and Classification
A pulsed millimeter wave radar operating at a frame rate of 144 Hz is utilized to record 2160 scattering signatures of twelve generic hand gestures. Gesture recognition is achieved by machine learning, utilizing transfer learning on a pre-trained convolutional neural network. This yields excellent classification results with a validation accuracy of 99.5%, based on a 60% training vs. 40% validation split. The corresponding confusion matrix is also presented, showing a high level of classification orthogonality between the tested gestures. This is the first demonstration where data from a pulsed millimeter wave radar is used for gesture recognition by machine learning. It proves that the range-time envelope representation of high frame-rate data from a pulsed radar is suitable for hand gesture recognition. Further improvements are expected for more complex detection schemes and tailored neural networks.