Kunito Okuyama
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kunito Okuyama has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Yoshihiro Iida
25 shared publications- Shoji Mori
Department of Chemical Engineering Science, Yokohama National University
23 shared publications - Mikako Tanaka
Graduate School of Engineering Science, Yokohama National University
7 shared publications Jeong-Hun Kim
4 shared publicationsGen Kojima
3 shared publicationsTakeo Takashima
Oyama National College of Technology
3 shared publications
Latest Publications
- Open Access
- 22 February 2023
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 37 (1) , 138-145
充填層の毛管力を利用したメタノールからの合成ガスの生成
Passive production of synthesis gas from liquid methanol using a capillary action in a packed bed of porous particles supporting a catalyst is investigated. Heating of an upper side of the packed tube while the bottom is immersed in liquid methanol causes upward fluid flow due to capillary action enhanced by evaporation and produces the synthesis gas in the high temperature region. For an increased diameter of the bed, the partial invasion of wetted region into the core of the dried region may cause a significant reduction in reaction yield. The radial distribution of temperature and its effect on the reaction are identified from the experiment. Un-uniformity caused in the radial direction is discussed based on the physical modeling of the capillary liquid flow toward the heated wall.
- 22 February 2023
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 37 (1) , 138-145
Open Access充填層の毛管力を利用したメタノールからの合成ガスの生成
Passive production of synthesis gas from liquid methanol using a capillary action in a packed bed of porous particles supporting a catalyst is investigated. Heating of an upper side of the packed tube while the bottom is immersed in liquid methanol causes upward fluid flow due to capillary action enhanced by evaporation and produces the synthesis gas in the high temperature region. For an increased diameter of the bed, the partial invasion of wetted region into the core of the dried region may cause a significant reduction in reaction yield. The radial distribution of temperature and its effect on the reaction are identified from the experiment. Un-uniformity caused in the radial direction is discussed based on the physical modeling of the capillary liquid flow toward the heated wall.
- 1 March 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 133, 576-579
Rapid cooling of a high-temperature block by the attachment of a honeycomb porous plate on a nanoparticle-deposited surface
- 1 March 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 133, 576-579
Rapid cooling of a high-temperature block by the attachment of a honeycomb porous plate on a nanoparticle-deposited surface
- 1 January 2017
- Published by Begell House Inc. Publishers
RAPID GENERATION MECHANISM OF SUPERHEATED STEAM USING A WATER CONTAINING POROUS MATERIAL
A simple method for the rapid generation of superheated steam using a water-containing porous material was proposed. The start-up response and the rate of energy conversion for input power are within several seconds and higher than approximately 90%, respectively. In this paper, in order to clarify the mechanism of the rapid generation of superheated steam, the temperature of steam, and the surface roughness of porous materials were investigated experimentally. In conclusion, narrow gaps between a heated coil and porous material could contribute to the rapid generation of superheated steam.
- 1 January 2017
- Published by Begell House Inc. Publishers
RAPID GENERATION MECHANISM OF SUPERHEATED STEAM USING A WATER CONTAINING POROUS MATERIAL
A simple method for the rapid generation of superheated steam using a water-containing porous material was proposed. The start-up response and the rate of energy conversion for input power are within several seconds and higher than approximately 90%, respectively. In this paper, in order to clarify the mechanism of the rapid generation of superheated steam, the temperature of steam, and the surface roughness of porous materials were investigated experimentally. In conclusion, narrow gaps between a heated coil and porous material could contribute to the rapid generation of superheated steam.
- 1 February 2016
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 93, 1159-1168
Novel process for the rapid and efficient generation of superheated steam using a water-containing porous material
- 1 February 2016
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 93, 1159-1168
Novel process for the rapid and efficient generation of superheated steam using a water-containing porous material
- 20 October 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (7) , 1028-1035
CHF enhancement by honeycomb porous plate in saturated pool boiling of nanofluid
One strategy for severe accidents is in-vessel retention (IVR) of corium debris. In order to enhance the capability of IVR in the case of a severe accident involving a light-water reactor, methods to increase the critical heat flux (CHF) should be considered. Approaches for increasing the IVR capability must be simple and installable at low cost. Moreover, cooling techniques for IVR should be applicable to a large heated surface. Therefore, as a suitable cooling technology for required conditions, we proposed cooling approaches using a honeycomb porous plate for the CHF enhancement of a large heated surface in a saturated pool boiling of pure water. In this paper, CHF enhancement by the attachment of a honeycomb-structured porous plate to a heated surface in saturated pool boiling of a TiO2-water nanofluid was investigated experimentally under atmospheric pressure. As a result, the CHF with a honeycomb porous plate increases as the nanoparticle concentration increases. The CHF is enhanced significantly up to 3.2 MW/m2 at maximum upon the attachment of a honeycomb porous plate with 0.1 vol.% nanofluid. To the best of the author's knowledge, under atmospheric pressure, a CHF of 3.2 MW/m2 is the highest value for a relatively large heated surface having a diameter exceeding 30 mm.
- 20 October 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (7) , 1028-1035
CHF enhancement by honeycomb porous plate in saturated pool boiling of nanofluid
One strategy for severe accidents is in-vessel retention (IVR) of corium debris. In order to enhance the capability of IVR in the case of a severe accident involving a light-water reactor, methods to increase the critical heat flux (CHF) should be considered. Approaches for increasing the IVR capability must be simple and installable at low cost. Moreover, cooling techniques for IVR should be applicable to a large heated surface. Therefore, as a suitable cooling technology for required conditions, we proposed cooling approaches using a honeycomb porous plate for the CHF enhancement of a large heated surface in a saturated pool boiling of pure water. In this paper, CHF enhancement by the attachment of a honeycomb-structured porous plate to a heated surface in saturated pool boiling of a TiO2-water nanofluid was investigated experimentally under atmospheric pressure. As a result, the CHF with a honeycomb porous plate increases as the nanoparticle concentration increases. The CHF is enhanced significantly up to 3.2 MW/m2 at maximum upon the attachment of a honeycomb porous plate with 0.1 vol.% nanofluid. To the best of the author's knowledge, under atmospheric pressure, a CHF of 3.2 MW/m2 is the highest value for a relatively large heated surface having a diameter exceeding 30 mm.
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Thermal Engineering Conference
- Vol. 2015, _B131-1_
B131 The effect of honeycomb porous plate on CHF in a saturated pool boiling of FC-72
Pool boiling has been used for cooling in numerous thermal energy dissipation systems, such as high-power electronics, heat exchangers, and nuclear reactors. FC-72 is often used as a coolant for electronic cooling. While Critical Heat Flux(CHF) was increased by attaching a honeycomb porous plate to heated surface in a saturated pool boiling of water. For the case of water, CHF was enhanced up to about twice compared to that of plain surface (2 MW/m^2). In this study, we investigated experimentally the effect of honeycomb porous plate on CHF in a saturated pool boiling of FC-72.
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Thermal Engineering Conference
- Vol. 2015, _B131-1_
B131 The effect of honeycomb porous plate on CHF in a saturated pool boiling of FC-72
Pool boiling has been used for cooling in numerous thermal energy dissipation systems, such as high-power electronics, heat exchangers, and nuclear reactors. FC-72 is often used as a coolant for electronic cooling. While Critical Heat Flux(CHF) was increased by attaching a honeycomb porous plate to heated surface in a saturated pool boiling of water. For the case of water, CHF was enhanced up to about twice compared to that of plain surface (2 MW/m^2). In this study, we investigated experimentally the effect of honeycomb porous plate on CHF in a saturated pool boiling of FC-72.
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 81 (822) , 14-00292
Passive production of synthesis gas from liquid methanol using a porous material block
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 81 (822) , 14-00292
Passive production of synthesis gas from liquid methanol using a porous material block
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of the National Symposium on Power and Energy Systems
- Vol. 2014.19, 171-172
F123 Transient CHF enhancement of saturated pool boiling of water using a honeycomb porous media
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of the National Symposium on Power and Energy Systems
- Vol. 2014.19, 171-172
F123 Transient CHF enhancement of saturated pool boiling of water using a honeycomb porous media
- 1 January 2014
- Published by Begell House Inc. Publishers
Dynamics of Evaporation in a Single, Straight-Tube Pulsating Heat Pipe
The dynamics of vapor flow in a pulsating heat pipe consisting of a single, straight tube (SST-PHP) is investigated using a hot-wire anemometric technique. The proposed SST-PHP generates stable and periodic oscillation of a single vapor plug with a large stroke that transports the heat of 75 W with an effective thermal conductivity of 40 kW/(m?K) at horizontal orientation. Vapor produced in the heating section flows into the heat transport tube and condenses on a liquid film formed between the vapor plug and the tube wall to transport heat from the heating section to the heat transport tube. The measured flow rate of vapor varies drastically during one oscillation cycle, i.e., increases to approximately ten times the molar rate of increase of vapor in the vapor plug during the growth period while remaining relatively low during shrinkage. The evaporation rate in the heating section, which is evaluated from the vapor flow rate, significantly exceeds the vapor generation rate that corresponds to the heat transport rate during the growth of the vapor plug. The condensation rate varies similarly with the evaporation rate in accordance with the oscillation motion of the vapor plug. The storage and release of the sensible heat at the liquid film resulting from the variation in the saturation temperature due to the pressure oscillation are suggested to play a significant role in the dynamics of vapor generation and the large-amplitude oscillation.
- 1 January 2014
- Published by Begell House Inc. Publishers
Dynamics of Evaporation in a Single, Straight-Tube Pulsating Heat Pipe
The dynamics of vapor flow in a pulsating heat pipe consisting of a single, straight tube (SST-PHP) is investigated using a hot-wire anemometric technique. The proposed SST-PHP generates stable and periodic oscillation of a single vapor plug with a large stroke that transports the heat of 75 W with an effective thermal conductivity of 40 kW/(m?K) at horizontal orientation. Vapor produced in the heating section flows into the heat transport tube and condenses on a liquid film formed between the vapor plug and the tube wall to transport heat from the heating section to the heat transport tube. The measured flow rate of vapor varies drastically during one oscillation cycle, i.e., increases to approximately ten times the molar rate of increase of vapor in the vapor plug during the growth period while remaining relatively low during shrinkage. The evaporation rate in the heating section, which is evaluated from the vapor flow rate, significantly exceeds the vapor generation rate that corresponds to the heat transport rate during the growth of the vapor plug. The condensation rate varies similarly with the evaporation rate in accordance with the oscillation motion of the vapor plug. The storage and release of the sensible heat at the liquid film resulting from the variation in the saturation temperature due to the pressure oscillation are suggested to play a significant role in the dynamics of vapor generation and the large-amplitude oscillation.
- 1 September 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 64, 254-262
A single, straight-tube pulsating heat pipe (examination of a mechanism for the enhancement of heat transport)
- 1 September 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 64, 254-262
A single, straight-tube pulsating heat pipe (examination of a mechanism for the enhancement of heat transport)