Guojiang Liao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guojiang Liao has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Shouhu Xuan
3 shared publications- Xinglong Gong
Department of Modern Mechanics, University of Science and Technology of China, Hefei, China
3 shared publications Fayuan Wei
Institute of Systems Engineering, China Academy of Engineering Physics, Mianyang, People’s Republic of China
2 shared publicationsQiang Wan
Institute of Systems Engineering, China Academy of Engineering Physics, Mianyang, People’s Republic of China
2 shared publications- Shouhu Xuan
CAS Key Laboratory of Mechanical Behavior and Design of Materials, Department of Modern Mechanics, University of Science and Technology of China, Hefei, 230026, PR China
2 shared publications Xinglong Gong
2 shared publications
Latest Publications
- Open Access
Influence of Gamma Radiation on the Damping Property of Magnetorheological Elastomer
Magnetorheological elastomer (MRE) is a kind of smart material, whose mechanical property can be controlled by the external magnetic field quickly and reversibly. The damping property of MRE is one of the most concerned properties when designing MRE based devices. In this work, the influence of gamma radiation on the damping property of MRE was investigated. Six different exposures of gamma radiation were applied to the MRE samples. The highest gamma radiation dose was up to 1 × 105 Gy(Si), which can cover most of the engineering application scenarios. The influence of gamma radiation on the damping-strain relation and the damping-magnetic-field relation were studied. The probable mechanisms were discussed in detail. It is found that the gamma radiation does not affect the variation trend of loss factor of MRE with increasing strain amplitude or magnetic flux density. But it affects the variation trend of the maximum change of strain-induced or magnetic-field-induced loss factor of MRE. Besides, with constant strain and constant magnetic flux density, the loss factor of MRE shows w-shape variation trend with increasing gamma radiation dose. It is considered to be resulted from the combined action of the intrinsic damping and the interfacial friction damping of MRE.
Open AccessInfluence of Gamma Radiation on the Damping Property of Magnetorheological Elastomer
Magnetorheological elastomer (MRE) is a kind of smart material, whose mechanical property can be controlled by the external magnetic field quickly and reversibly. The damping property of MRE is one of the most concerned properties when designing MRE based devices. In this work, the influence of gamma radiation on the damping property of MRE was investigated. Six different exposures of gamma radiation were applied to the MRE samples. The highest gamma radiation dose was up to 1 × 105 Gy(Si), which can cover most of the engineering application scenarios. The influence of gamma radiation on the damping-strain relation and the damping-magnetic-field relation were studied. The probable mechanisms were discussed in detail. It is found that the gamma radiation does not affect the variation trend of loss factor of MRE with increasing strain amplitude or magnetic flux density. But it affects the variation trend of the maximum change of strain-induced or magnetic-field-induced loss factor of MRE. Besides, with constant strain and constant magnetic flux density, the loss factor of MRE shows w-shape variation trend with increasing gamma radiation dose. It is considered to be resulted from the combined action of the intrinsic damping and the interfacial friction damping of MRE.
- Open Access
- 1 July 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (7) , 075701
Rate-dependent viscoelasticity of an impact-hardening polymer under oscillatory shear
The rate-dependent effect of viscoelasticity plays a critical role in the hardening mechanisms of impact-hardening polymers (IHP) when forcefully impacted. In this study, we used dynamic mechanical analysis (DMA) to characterize the rate-dependent viscoelasticity of an IHP under oscillatory shear. We found that the storage modulus increased by three orders of magnitude within the experimental range when the oscillatory frequency varied from 0.1 to 100 rad/s. To further understand the real strain rate effect of IHP, we introduced the Havriliak-Negami (H–N) model to predict the dynamic viscoelastic behaviors of the IHP for a wider frequency range (from zero to infinity) than that applied in the DMA experiments. Based on the H–N model results, we defined a parameter to describe the rate-dependent effect of the IHP, which was not dependent on the frequency range and reflected the intrinsic material properties of IHP. We used the time-temperature superposition principle (TTSP), which extended the experimental range from 0.1 rad s−1 down to 0.005 rad s−1, to verify the accuracy of the rate-dependent viscoelasticity predicted by the H–N model. Finally, we outlined the influence of temperature on the dynamic viscoelastic behaviors of IHP and discussed the phase transition mechanism induced by temperature and the oscillatory frequency. The results presented here not only provide a method (i.e., by combining experimental results with the H–N model results) to characterize the real rate-dependent viscoelasticity of IHP but are also valuable to further our understanding of the impact-hardening mechanisms of IHP.
- 1 July 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (7) , 075701
Open AccessRate-dependent viscoelasticity of an impact-hardening polymer under oscillatory shear
The rate-dependent effect of viscoelasticity plays a critical role in the hardening mechanisms of impact-hardening polymers (IHP) when forcefully impacted. In this study, we used dynamic mechanical analysis (DMA) to characterize the rate-dependent viscoelasticity of an IHP under oscillatory shear. We found that the storage modulus increased by three orders of magnitude within the experimental range when the oscillatory frequency varied from 0.1 to 100 rad/s. To further understand the real strain rate effect of IHP, we introduced the Havriliak-Negami (H–N) model to predict the dynamic viscoelastic behaviors of the IHP for a wider frequency range (from zero to infinity) than that applied in the DMA experiments. Based on the H–N model results, we defined a parameter to describe the rate-dependent effect of the IHP, which was not dependent on the frequency range and reflected the intrinsic material properties of IHP. We used the time-temperature superposition principle (TTSP), which extended the experimental range from 0.1 rad s−1 down to 0.005 rad s−1, to verify the accuracy of the rate-dependent viscoelasticity predicted by the H–N model. Finally, we outlined the influence of temperature on the dynamic viscoelastic behaviors of IHP and discussed the phase transition mechanism induced by temperature and the oscillatory frequency. The results presented here not only provide a method (i.e., by combining experimental results with the H–N model results) to characterize the real rate-dependent viscoelasticity of IHP but are also valuable to further our understanding of the impact-hardening mechanisms of IHP.
- 28 July 2016
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 28 (6) , 728-739
Investigation on the phase-based fuzzy logic controller for magnetorheological elastomer vibration absorber
This article presents a phase-based fuzzy logic controller for magnetorheological elastomer vibration absorber to trace the excitation frequency rapidly. The phase difference between the relative acceleration of the vibration absorber mass and the absolute acceleration of the primary system is used as the input signal of the fuzzy logic controller to calculate the desired magnetic current. Compared with the traditional stiffness control strategy, the proposed controller does not rely on the accurate relationship between the magnetic current and the resonant frequency of the magnetorheological elastomer vibration absorber. Simulation and experiment results demonstrate that the proposed stiffness controller is efficient to make the magnetorheological elastomer vibration absorber trace the excitation frequency rapidly. When the excitation frequency varies, the magnetorheological elastomer vibration absorber can be tuned properly within several seconds.
- 28 July 2016
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 28 (6) , 728-739
Investigation on the phase-based fuzzy logic controller for magnetorheological elastomer vibration absorber
This article presents a phase-based fuzzy logic controller for magnetorheological elastomer vibration absorber to trace the excitation frequency rapidly. The phase difference between the relative acceleration of the vibration absorber mass and the absolute acceleration of the primary system is used as the input signal of the fuzzy logic controller to calculate the desired magnetic current. Compared with the traditional stiffness control strategy, the proposed controller does not rely on the accurate relationship between the magnetic current and the resonant frequency of the magnetorheological elastomer vibration absorber. Simulation and experiment results demonstrate that the proposed stiffness controller is efficient to make the magnetorheological elastomer vibration absorber trace the excitation frequency rapidly. When the excitation frequency varies, the magnetorheological elastomer vibration absorber can be tuned properly within several seconds.
- 1 July 2016
- Published by Elsevier in Materials Letters
- Vol. 174, 79-81
Influence of γ radiation on the shear modulus of magnetorheological elastomer
- 1 July 2016
- Published by Elsevier in Materials Letters
- Vol. 174, 79-81
Influence of γ radiation on the shear modulus of magnetorheological elastomer
- 10 December 2013
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 23 (1) , 015016
Phase based stiffness tuning algorithm for a magnetorheological elastomer dynamic vibration absorber
This paper presents a phase based stiffness tuning algorithm to overcome the uncertainty of the relation between the magnetic current and the natural frequency for magnetorheological elastomer (MRE) dynamic vibration absorbers (DVA) caused by the nonlinearity of the MRE. The phase difference of the relative acceleration of the DVA mass and the absolute acceleration of the primary system was used to check whether the natural frequency of the DVA is adjusted to the excitation frequency. The magnetic current was controlled by the phase difference, which made the proposed algorithm not rely on the model of the MRE DVA. Both the simulation and the experiment demonstrate that the proposed algorithm is efficient for MRE DVA in rapidly tracking the excitation frequency.
- 10 December 2013
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 23 (1) , 015016
Phase based stiffness tuning algorithm for a magnetorheological elastomer dynamic vibration absorber
This paper presents a phase based stiffness tuning algorithm to overcome the uncertainty of the relation between the magnetic current and the natural frequency for magnetorheological elastomer (MRE) dynamic vibration absorbers (DVA) caused by the nonlinearity of the MRE. The phase difference of the relative acceleration of the DVA mass and the absolute acceleration of the primary system was used to check whether the natural frequency of the DVA is adjusted to the excitation frequency. The magnetic current was controlled by the phase difference, which made the proposed algorithm not rely on the model of the MRE DVA. Both the simulation and the experiment demonstrate that the proposed algorithm is efficient for MRE DVA in rapidly tracking the excitation frequency.
- 1 September 2013
- Published by Elsevier in Materials Letters
- Vol. 106, 270-272
Influence of shear deformation on the normal force of magnetorheological elastomer
- 1 September 2013
- Published by Elsevier in Materials Letters
- Vol. 106, 270-272
Influence of shear deformation on the normal force of magnetorheological elastomer
- 11 June 2013
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 52 (25) , 8445-8453
Magnetic Field-Induced Compressive Property of Magnetorheological Elastomer under High Strain Rate
- 11 June 2013
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 52 (25) , 8445-8453
Magnetic Field-Induced Compressive Property of Magnetorheological Elastomer under High Strain Rate
- 21 May 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (21) , 211909
Full-field deformation of magnetorheological elastomer under uniform magnetic field
A digital holographic interferometry was applied to analyze the morphology transformation of the magnetorheological elastomer, and both the contraction and stretch deformation were observed under applying an external magnetic field on the sample. Both isolated particles and grouped particles were observed in the magnetorheological elastomer sample, and these two kinds of particles resulted in the concave-convex deformation of the sample. The deformation of magnetorheological elastomer was calculated by using a 2D finite element model, and the results agreed well with the experimental analysis.
- 21 May 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (21) , 211909
Full-field deformation of magnetorheological elastomer under uniform magnetic field
A digital holographic interferometry was applied to analyze the morphology transformation of the magnetorheological elastomer, and both the contraction and stretch deformation were observed under applying an external magnetic field on the sample. Both isolated particles and grouped particles were observed in the magnetorheological elastomer sample, and these two kinds of particles resulted in the concave-convex deformation of the sample. The deformation of magnetorheological elastomer was calculated by using a 2D finite element model, and the results agreed well with the experimental analysis.
- 16 February 2012
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 51 (8) , 3322-3328
Magnetic-Field-Induced Normal Force of Magnetorheological Elastomer under Compression Status
- 16 February 2012
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 51 (8) , 3322-3328
Magnetic-Field-Induced Normal Force of Magnetorheological Elastomer under Compression Status
- 8 December 2011
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 23 (1) , 25-33
Development of a real-time tunable stiffness and damping vibration isolator based on magnetorheological elastomer
A tunable stiffness and damping vibration isolator based on magnetorheological elastomers (MREs) is developed. In this isolator, four MRE elements are used as the tunable springs, whose stiffness can be controlled by varying the magnetic field. A voice coil motor, which is controlled by the relative velocity feedback of the payload, is used as the tunable damper of the isolator. Under the combined ON–OFF control, the proposed vibration isolator shows satisfying isolation effect. The experimental results indicate that the responses of the payload are suppressed significantly in comparison to the passive system. The transmissibility of the payload around the resonant frequency is decreased by 61.5%. The root mean square (RMS) value and the maximum value of the displacement responses of the payload are decreased by 36.0% and 50.0%, respectively. In addition, the RMS values and maximum values of the velocity responses are decreased by 45.4% and 52.5%, respectively.
- 8 December 2011
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 23 (1) , 25-33
Development of a real-time tunable stiffness and damping vibration isolator based on magnetorheological elastomer
A tunable stiffness and damping vibration isolator based on magnetorheological elastomers (MREs) is developed. In this isolator, four MRE elements are used as the tunable springs, whose stiffness can be controlled by varying the magnetic field. A voice coil motor, which is controlled by the relative velocity feedback of the payload, is used as the tunable damper of the isolator. Under the combined ON–OFF control, the proposed vibration isolator shows satisfying isolation effect. The experimental results indicate that the responses of the payload are suppressed significantly in comparison to the passive system. The transmissibility of the payload around the resonant frequency is decreased by 61.5%. The root mean square (RMS) value and the maximum value of the displacement responses of the payload are decreased by 36.0% and 50.0%, respectively. In addition, the RMS values and maximum values of the velocity responses are decreased by 45.4% and 52.5%, respectively.