Vitaliy Ivanov
Vitaliy Ivanov has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Elena Lavrova
State Higher Educational Institution «Priazovskiy State Technical University
12 shared publications Elena Lavrova
Pryazovskyi State Tech Univ, Mariupol, Russia
2 shared publications- Fedor Morgay2 shared publications
L.K. Leshchynskyi
2 shared publicationsS.V. Shcherbakov
2 shared publicationsSHEI «Pryazovskyi State Technical University» of MES of Ukraine
2 shared publications
Latest Publications
- 29 October 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (2) , 187-192
Fracture resistance of the deposited metal under dynamic and cyclic loading
Analyses of experimental data are presented that enable the fracture resistance assessment of dynamically and cyclically loaded materials used for the manufacture and surfacing of rollers in continuous casting machines for beam blanks and crimping mill rollers. It has been noted that steels for manufacturing and surfacing of crimping rolls with different carbon content and alloying elements, differ in the determination fraction of the crack nucleation work in the integral value of the impact strength. The value of that fraction is much higher for corrosion-resistant steels of the Cr13 type which are also distinguished by high fracture resistance to cyclic loading. It is shown that the properties of these steels make it possible, along with the use of CCM rollers for surfacing, to recommend them for hardening the rollers in crimping mills. The possibility of an additional increase in the efficiency of the crimping rolls by eliminating uneven wear along the length of the barrel by surfacing a layer of Cr13 steel with a variable carbon content (0.10-0.25 %) is considered.
- 29 October 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (2) , 187-192
Fracture resistance of the deposited metal under dynamic and cyclic loading
Analyses of experimental data are presented that enable the fracture resistance assessment of dynamically and cyclically loaded materials used for the manufacture and surfacing of rollers in continuous casting machines for beam blanks and crimping mill rollers. It has been noted that steels for manufacturing and surfacing of crimping rolls with different carbon content and alloying elements, differ in the determination fraction of the crack nucleation work in the integral value of the impact strength. The value of that fraction is much higher for corrosion-resistant steels of the Cr13 type which are also distinguished by high fracture resistance to cyclic loading. It is shown that the properties of these steels make it possible, along with the use of CCM rollers for surfacing, to recommend them for hardening the rollers in crimping mills. The possibility of an additional increase in the efficiency of the crimping rolls by eliminating uneven wear along the length of the barrel by surfacing a layer of Cr13 steel with a variable carbon content (0.10-0.25 %) is considered.
- Open Access
The Effect of Welding Mode Parameters on the Operational Properties of Flexible Compensating Elements Made of Austenitic Stainless Steels
The paper investigates the effect of welding mode parameters on the uniformity of the deformation capacity of AISI 316 austenitic steel samples, namely, the influence of the welding current and purging gas consumption on the samples’ ability to perceive the force of cold cupping. Punch diameters of 3 and 8 mm were employed for the Erikson test to establish the dependence of the purge gas flow rate on the depth of the hole before the formation of cracks. The conducted metallographic studies confirmed an increase in the homogeneity of the dendritic structure in the weld zone due to the redistribution of heat input, as well as the absence of uneven grains and a decrease in the spread of grain sizes, which were in the range of 0.068–0.045 mm. The study resulted in determining the optimal range of technological parameters for the manufacture of flexible expansion elements to ensure their high operational properties.
Open AccessThe Effect of Welding Mode Parameters on the Operational Properties of Flexible Compensating Elements Made of Austenitic Stainless Steels
The paper investigates the effect of welding mode parameters on the uniformity of the deformation capacity of AISI 316 austenitic steel samples, namely, the influence of the welding current and purging gas consumption on the samples’ ability to perceive the force of cold cupping. Punch diameters of 3 and 8 mm were employed for the Erikson test to establish the dependence of the purge gas flow rate on the depth of the hole before the formation of cracks. The conducted metallographic studies confirmed an increase in the homogeneity of the dendritic structure in the weld zone due to the redistribution of heat input, as well as the absence of uneven grains and a decrease in the spread of grain sizes, which were in the range of 0.068–0.045 mm. The study resulted in determining the optimal range of technological parameters for the manufacture of flexible expansion elements to ensure their high operational properties.
- 10 February 2022
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 328, 107-114
Modeling the Influence of Mechanical Control Impacts on the Distribution of the Temperature Field in the Base Metal during Surfacing with a Strip Electrode
Modeling of the temperature distribution during electric arc surfacing with a strip electrode is carried out in relation to the design scheme of a semi-infinite body. Also, in the work, the temperature distribution was calculated when a flat layer was heated by a linear source, which made it possible to compare the temperature distribution data without and taking into account the heat release conditions at the product boundaries. The simulation results showed that the control of heat input into the base metal when using mechanical control actions makes it possible to reduce the overheating of the weld pool, reduce the area of the melting isotherm, and reduce the cooling rate of the heat-affected zone. By calculation, the previously determined optimal range of values of the frequency of control actions of 40÷60 Hz was confirmed, which makes it possible to ensure the minimum depth of penetration of the base metal and obtain a favorable structure in the heat-affected zone, prone to the formation of a coarse-grained structure.
- 10 February 2022
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 328, 107-114
Modeling the Influence of Mechanical Control Impacts on the Distribution of the Temperature Field in the Base Metal during Surfacing with a Strip Electrode
Modeling of the temperature distribution during electric arc surfacing with a strip electrode is carried out in relation to the design scheme of a semi-infinite body. Also, in the work, the temperature distribution was calculated when a flat layer was heated by a linear source, which made it possible to compare the temperature distribution data without and taking into account the heat release conditions at the product boundaries. The simulation results showed that the control of heat input into the base metal when using mechanical control actions makes it possible to reduce the overheating of the weld pool, reduce the area of the melting isotherm, and reduce the cooling rate of the heat-affected zone. By calculation, the previously determined optimal range of values of the frequency of control actions of 40÷60 Hz was confirmed, which makes it possible to ensure the minimum depth of penetration of the base metal and obtain a favorable structure in the heat-affected zone, prone to the formation of a coarse-grained structure.
- Open Access
- 29 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (114)) , 38-46
Design of an universal source for semi-automatic ac welding and induction heating
This paper proposes a circuit solution and a power source control algorithm for semi-automatic AC welding with improved energy and weight-size characteristics. A distinctive feature of the designed source is the absence of an input rectifier: welding is carried out with a high-frequency alternating current. That has made it possible to significantly reduce power losses in the source, as well as provide the possibility of implementing induction heating by connecting an inductor to the source output. Another distinctive feature of the designed source is an increased power factor and a reduced level of higher harmonics of the current consumed. The power factor of the described source reaches 0.94 against 0.5÷0.7 for sources equipped with a conventional rectifier with capacitive smoothing. The designed source's composition includes a power supply system for the wire feed drive with speed stabilization due to positive feedback on the motor current. That has made it possible to ensure the stable operation of the drive in a wide range of speeds. A model has also been developed of a flux wire welding torch containing a feed drive and a coil with a wire (up to 100 mm in diameter), placed, in order to reduce the size, in the handle of the torch. In addition to the welding function, the source makes it possible to solve the tasks related to induction heating and/or hardening of small parts; to that end, a compact inductor is connected to its output. Tests of the source showed the feasibility of the proposed ideas and circuit solutions. The dimensions of the source are 190×107×65 mm; weight, 1.4 kg; output current, up to 120 A. The proposed technical solution enables the construction of small-sized, lightweight, universal, easy-to-use power supplies for semi-automatic welding with the option of induction heating
- 29 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (114)) , 38-46
Open AccessDesign of an universal source for semi-automatic ac welding and induction heating
This paper proposes a circuit solution and a power source control algorithm for semi-automatic AC welding with improved energy and weight-size characteristics. A distinctive feature of the designed source is the absence of an input rectifier: welding is carried out with a high-frequency alternating current. That has made it possible to significantly reduce power losses in the source, as well as provide the possibility of implementing induction heating by connecting an inductor to the source output. Another distinctive feature of the designed source is an increased power factor and a reduced level of higher harmonics of the current consumed. The power factor of the described source reaches 0.94 against 0.5÷0.7 for sources equipped with a conventional rectifier with capacitive smoothing. The designed source's composition includes a power supply system for the wire feed drive with speed stabilization due to positive feedback on the motor current. That has made it possible to ensure the stable operation of the drive in a wide range of speeds. A model has also been developed of a flux wire welding torch containing a feed drive and a coil with a wire (up to 100 mm in diameter), placed, in order to reduce the size, in the handle of the torch. In addition to the welding function, the source makes it possible to solve the tasks related to induction heating and/or hardening of small parts; to that end, a compact inductor is connected to its output. Tests of the source showed the feasibility of the proposed ideas and circuit solutions. The dimensions of the source are 190×107×65 mm; weight, 1.4 kg; output current, up to 120 A. The proposed technical solution enables the construction of small-sized, lightweight, universal, easy-to-use power supplies for semi-automatic welding with the option of induction heating
- Open Access
- 10 September 2021
- Published by European Scientific Platform (Publications)
RESEARCH OF THE DROPLET TRANSFER PROCESS DURING SURFACING BY AUSTENITIC STRIP ELECTRODES WITH MECHANICAL CONTROL IMPACTS
- 10 September 2021
- Published by European Scientific Platform (Publications)
Open AccessRESEARCH OF THE DROPLET TRANSFER PROCESS DURING SURFACING BY AUSTENITIC STRIP ELECTRODES WITH MECHANICAL CONTROL IMPACTS
- 28 August 2021
- Published by International Association Welding in Автоматическая сварка
- Vol. 2021 (8) , 14-17
Development of surfacing technology for the working layer of variable composition on the blooming rolls
- 28 August 2021
- Published by International Association Welding in Автоматическая сварка
- Vol. 2021 (8) , 14-17
Development of surfacing technology for the working layer of variable composition on the blooming rolls
- Open Access
- 19 February 2021
- Published by European Scientific Platform (Publications) in Grail of Science
- No. 1
INVESTIGATION OF THE EXPLOITATION CHARACTERISTICS OF BELLOWS EXPANSION JOINTS MADE OF HEAT-RESISTANT NICKEL ALLOY
Investigations of the macro- and microstructure, mechanical and technological properties of a metal strip made of heat-resistant nickel alloy Cr20Ni43Mo9Mn6Nb-vi were carried out. In order to determine the optimal composition of the pickling solution, studies were carried out on the use of various mixtures for pickling the surface of the strip. On the basis of the studies carried out, technological recommendations were developed for the preparation of materials before welding of bellows expansion joints.
- 19 February 2021
- Published by European Scientific Platform (Publications) in Grail of Science
- No. 1
Open AccessINVESTIGATION OF THE EXPLOITATION CHARACTERISTICS OF BELLOWS EXPANSION JOINTS MADE OF HEAT-RESISTANT NICKEL ALLOY
Investigations of the macro- and microstructure, mechanical and technological properties of a metal strip made of heat-resistant nickel alloy Cr20Ni43Mo9Mn6Nb-vi were carried out. In order to determine the optimal composition of the pickling solution, studies were carried out on the use of various mixtures for pickling the surface of the strip. On the basis of the studies carried out, technological recommendations were developed for the preparation of materials before welding of bellows expansion joints.
- Open Access
- 5 February 2021
- Published by European Scientific Platform (Publications)
DEVELOPMENT OF A DEVICE FOR ELECTRIC ARC OVERLAYING WITH TWO STRIP ELECTRODES WITH CONTROLLED ELECTRODE METAL TRANSFER
- 5 February 2021
- Published by European Scientific Platform (Publications)
Open AccessDEVELOPMENT OF A DEVICE FOR ELECTRIC ARC OVERLAYING WITH TWO STRIP ELECTRODES WITH CONTROLLED ELECTRODE METAL TRANSFER
- Open Access
- 5 June 2020
- Published by European Scientific Platform
- p. 86-87
PECULIARITIES OF ELECTRODE DROPLET TRANSFER CONTROL DURING OVERLAYING WELDING WITH A STRIP ELECTRODE
- 5 June 2020
- Published by European Scientific Platform
- p. 86-87
Open AccessPECULIARITIES OF ELECTRODE DROPLET TRANSFER CONTROL DURING OVERLAYING WELDING WITH A STRIP ELECTRODE
- Open Access
- 1 May 2020
- Published by European Scientific Platform
- p. 34-36
STUDY OF THE INFLUENCE OF CONTROLLED ELECTRODE METAL TRANSFER DURING ELECTRIC ARC SURFACING ON THE CONTACT FATIGUE OF THE DEPOSITED LAYER
- 1 May 2020
- Published by European Scientific Platform
- p. 34-36
Open AccessSTUDY OF THE INFLUENCE OF CONTROLLED ELECTRODE METAL TRANSFER DURING ELECTRIC ARC SURFACING ON THE CONTACT FATIGUE OF THE DEPOSITED LAYER