Javad Akbardoost
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Javad Akbardoost has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Ali Reza Torabi
Fracture Research Laboratory, College of Interdisciplinary Science and Technology, University of Tehran, Tehran 1439957131, Iran
3 shared publications Mahdi Akbari
Fracture Research Laboratory, College of Interdisciplinary Science and Technology University of Tehran Tehran Iran
2 shared publicationsMaryam Aslani
Department of Mechanical Engineering, Kharazmi University, Tehran, Islamic Republic of Iran
2 shared publications- Mohammad Reza Mohammad Aliha
Welding and Joining Research Center, School of Industrial Engineering, Iran University of Science and Technology (IUST), Narmak, Iran
2 shared publications - Sergio Cicero
Laboratory of Materials Science and Engineering (LADICIM), Departamento de Ciencia e Ingeniería del Terreno y de los Materiales, University of Cantabria, Avenida de los Castros, 44, 39005 Santander, Spain
2 shared publications A. R. Torabi
Fracture Research Laboratory, Faculty of New Sciences and Technologies, Univ. of Tehran, Tehran 14399-57131, Iran
1 shared publication
Latest Publications
- 22 May 2026
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 17 (6) , 1-30
Size effects on fracture toughness of polymeric specimens weakened by V-notches with end holes (VO) subjected to opening mode loading
Purpose: This study aims to investigate the effect of specimen size on the fracture resistance of V-notches with end holes (VO-notched) polymeric samples under opening mode loading experimentally and theoretically. Design/methodology/approach: First, a number of VO notched Brazilain disk (VONBD) and VO notcehd semi-circular bend (VONSCB) samples with different sizes were made from polymethyl methacrylate and general-purpose polystyrene sheets and then were tested under pure Mode I loading. After that, it is tried to predict the fracture resistance of notched samples using two stress-based criteria [point stress (PS) and mean stress (MS)] considering the size effect. Findings: First, it is found from experiments that the fracture resistance of polymeric VO-notched specimens varies with the size of specimen in such a way that notch fracture toughness increases by increasing the specimen size. Secondly, it is found that the PS and MS criteria are able to predict in good accuracy the fracture resistance of tested samples. Originality/value: The size effect on the notch fracture toughness of VO-notched polymeric samples is investigated for the first time, and it is the main novelty of this research.
- 22 May 2026
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 17 (6) , 1-30
Size effects on fracture toughness of polymeric specimens weakened by V-notches with end holes (VO) subjected to opening mode loading
Purpose: This study aims to investigate the effect of specimen size on the fracture resistance of V-notches with end holes (VO-notched) polymeric samples under opening mode loading experimentally and theoretically. Design/methodology/approach: First, a number of VO notched Brazilain disk (VONBD) and VO notcehd semi-circular bend (VONSCB) samples with different sizes were made from polymethyl methacrylate and general-purpose polystyrene sheets and then were tested under pure Mode I loading. After that, it is tried to predict the fracture resistance of notched samples using two stress-based criteria [point stress (PS) and mean stress (MS)] considering the size effect. Findings: First, it is found from experiments that the fracture resistance of polymeric VO-notched specimens varies with the size of specimen in such a way that notch fracture toughness increases by increasing the specimen size. Secondly, it is found that the PS and MS criteria are able to predict in good accuracy the fracture resistance of tested samples. Originality/value: The size effect on the notch fracture toughness of VO-notched polymeric samples is investigated for the first time, and it is the main novelty of this research.
- 13 May 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Theoretical Predictions and Experimental Assessments of Fracture in Round‐Tip V‐Notched Orthotropic Samples Under Pure Compression
In this paper, the fracture onset of rounded V‐notched orthotropic specimens under pure compression, made of Canadian maple, is assessed. Compressive fracture tests are conducted on the square‐shaped samples containing double‐edge RV‐shaped notches characterized by three different notch tip radii and a constant notch opening angle, up to fully development of cracking at the notch root is achieved. It is observed that the fracture loads across all specimens are nearly identical, despite noticeable variation in notch tip radii. It means that the fracture load may be independent of the notch radii. Moreover, the values of load‐bearing capacity for tested samples are predicted by two conventional stress‐based criteria, namely the point stress and mean stress integrated by the equivalent material concept for considering the notable nonlinear behavior and the virtual isotropic material concept to represent the orthotropic behavior of tested wood as an equivalent isotropic material. A good consistency between values of load‐bearing capacity predicted by all fracture criteria employed and the experimental results is observed.
- 13 May 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Theoretical Predictions and Experimental Assessments of Fracture in Round‐Tip V‐Notched Orthotropic Samples Under Pure Compression
In this paper, the fracture onset of rounded V‐notched orthotropic specimens under pure compression, made of Canadian maple, is assessed. Compressive fracture tests are conducted on the square‐shaped samples containing double‐edge RV‐shaped notches characterized by three different notch tip radii and a constant notch opening angle, up to fully development of cracking at the notch root is achieved. It is observed that the fracture loads across all specimens are nearly identical, despite noticeable variation in notch tip radii. It means that the fracture load may be independent of the notch radii. Moreover, the values of load‐bearing capacity for tested samples are predicted by two conventional stress‐based criteria, namely the point stress and mean stress integrated by the equivalent material concept for considering the notable nonlinear behavior and the virtual isotropic material concept to represent the orthotropic behavior of tested wood as an equivalent isotropic material. A good consistency between values of load‐bearing capacity predicted by all fracture criteria employed and the experimental results is observed.
- 17 April 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (9) , 1585-1598
Effect of mechanical reinforcement using nano-clay and acrylic impact modifiers on PMMA denture base: Evaluating single and hybrid additives
- 17 April 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (9) , 1585-1598
Effect of mechanical reinforcement using nano-clay and acrylic impact modifiers on PMMA denture base: Evaluating single and hybrid additives
- 17 January 2025
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 310
An energy-based approach for investigating the mixed-mode fracture behavior of bone as orthotropic material
- 17 January 2025
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 310
An energy-based approach for investigating the mixed-mode fracture behavior of bone as orthotropic material
- 9 April 2023
- Published by Springer Nature
- p. 65-90
Mixed-Mode I/II Fracture Load Prediction in Cracked Rock Geometries Using the Tangential Stress Contour (TSC) Method
- 9 April 2023
- Published by Springer Nature
- p. 65-90
Mixed-Mode I/II Fracture Load Prediction in Cracked Rock Geometries Using the Tangential Stress Contour (TSC) Method
- Open Access
Mixed Mode Fracture Investigation of Rock Specimens Containing Sharp V-Notches
This work aims to assess both experimentally and analytically the fracture behavior of rock specimens containing sharp V-notches (SV-notches) subjected to mixed mode I/II loading. To this end, firstly, several mixed mode fracture tests were conducted on Brazilian disk specimens weakened by an SV-notch (SVNBD sample), performed in their corresponding center and with various notch opening angles. Secondly, the fracture resistance of the tested samples was predicted using a criterion named MTS-FEM. This approach is based on the maximum tangential stress (MTS) criterion, in which the tangential stress is determined from the finite element method (FEM). Additionally, in the present research, the required critical distance is calculated directly from finite element analyses performed on cracked samples. Comparing the experimental results and the analytical predictions, it is shown that the fracture curves obtained from the MTS-FEM criterion are in agreement with the experimental results. These results are achieved without the need for the calculation of stress series expansion coefficients, as an additional advantage of the proposed approach.
Open AccessMixed Mode Fracture Investigation of Rock Specimens Containing Sharp V-Notches
This work aims to assess both experimentally and analytically the fracture behavior of rock specimens containing sharp V-notches (SV-notches) subjected to mixed mode I/II loading. To this end, firstly, several mixed mode fracture tests were conducted on Brazilian disk specimens weakened by an SV-notch (SVNBD sample), performed in their corresponding center and with various notch opening angles. Secondly, the fracture resistance of the tested samples was predicted using a criterion named MTS-FEM. This approach is based on the maximum tangential stress (MTS) criterion, in which the tangential stress is determined from the finite element method (FEM). Additionally, in the present research, the required critical distance is calculated directly from finite element analyses performed on cracked samples. Comparing the experimental results and the analytical predictions, it is shown that the fracture curves obtained from the MTS-FEM criterion are in agreement with the experimental results. These results are achieved without the need for the calculation of stress series expansion coefficients, as an additional advantage of the proposed approach.
- 1 July 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 148 (7) , 04022030
Size Effect on Mode I Fracture Resistance of Polymeric Rounded-Tip V-Notched Specimens Using the Modified Point Stress Criterion
In this research, size effects on the mode I notch fracture toughness of polymeric specimens weakened by a rounded-tip V-shaped (RV) notch are investigated experimentally and theoretically. For this purpose, multiple fracture tests are performed on the RV-notched Brazilian disk (RVNBD) and RV-notched semicircular bend (RVNSCB) polymeric samples with four different scales. Then, the fracture loads measured from the experiments are converted to the notch fracture toughness using finite element analysis. The experimental results show that the mode I notch fracture toughness is significantly dependent on the nominal dimension (radius) of RVNBD and RVNSCB samples, so by increasing the sample radius, the mode I notch fracture toughness increases. In order to justify the size dependency of notch fracture toughness, a modified form of the point stress criterion is proposed. The value of critical distance in the modified point stress (MPS) criterion is considered to be size-dependent. Subsequently, a semiempirical relation is used for describing this size dependency. It is revealed that the MPS criterion is able to predict the size-dependent value of notch fracture toughness for both RVNBD and RVNSCB samples made of polymeric materials well.- 1 July 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 148 (7) , 04022030
Size Effect on Mode I Fracture Resistance of Polymeric Rounded-Tip V-Notched Specimens Using the Modified Point Stress Criterion
In this research, size effects on the mode I notch fracture toughness of polymeric specimens weakened by a rounded-tip V-shaped (RV) notch are investigated experimentally and theoretically. For this purpose, multiple fracture tests are performed on the RV-notched Brazilian disk (RVNBD) and RV-notched semicircular bend (RVNSCB) polymeric samples with four different scales. Then, the fracture loads measured from the experiments are converted to the notch fracture toughness using finite element analysis. The experimental results show that the mode I notch fracture toughness is significantly dependent on the nominal dimension (radius) of RVNBD and RVNSCB samples, so by increasing the sample radius, the mode I notch fracture toughness increases. In order to justify the size dependency of notch fracture toughness, a modified form of the point stress criterion is proposed. The value of critical distance in the modified point stress (MPS) criterion is considered to be size-dependent. Subsequently, a semiempirical relation is used for describing this size dependency. It is revealed that the MPS criterion is able to predict the size-dependent value of notch fracture toughness for both RVNBD and RVNSCB samples made of polymeric materials well.- 14 June 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (21) , 10841-10851
A stress-based approach for considering the size effect on the mixed mode fracture behavior of rock
It is aimed in this research that a new approach is represented for justifying the influence of specimen size on the mixed mode I/II fracture behavior of rock. The new approach, namely, the MTS-FEM criterion, is an extension of the maximum tangential stress (MTS) criterion in which the finite element method (FEM) is employed for characterizing the tangential stress at the critical distance. Also, two points exist in the MTS-FEM approach for the critical distance. First one is that the critical distance is obtained directly from finite element analysis corresponding to results of mode I fracture test. The second point is that the critical distance from the crack tip is considered as a function of specimen size. The experimental results carried out in the previous studies on cracked Brazilian disks (CBD) with four different radii and under mixed mode loading are utilized with the aim to evaluate the new size effect criterion. It is illustrated that the MTS-FEM criterion is able to predict the mixed mode fracture resistance of rock considering the size effect well without calculating any parameters related to the stress or strain series expansion.
- 14 June 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (21) , 10841-10851
A stress-based approach for considering the size effect on the mixed mode fracture behavior of rock
It is aimed in this research that a new approach is represented for justifying the influence of specimen size on the mixed mode I/II fracture behavior of rock. The new approach, namely, the MTS-FEM criterion, is an extension of the maximum tangential stress (MTS) criterion in which the finite element method (FEM) is employed for characterizing the tangential stress at the critical distance. Also, two points exist in the MTS-FEM approach for the critical distance. First one is that the critical distance is obtained directly from finite element analysis corresponding to results of mode I fracture test. The second point is that the critical distance from the crack tip is considered as a function of specimen size. The experimental results carried out in the previous studies on cracked Brazilian disks (CBD) with four different radii and under mixed mode loading are utilized with the aim to evaluate the new size effect criterion. It is illustrated that the MTS-FEM criterion is able to predict the mixed mode fracture resistance of rock considering the size effect well without calculating any parameters related to the stress or strain series expansion.