Seungnam Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Seungnam Yu has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Chang-Soo Han
Department of Robot Engineering, Hanyang University, 55 Hanyangdaehak-ro, Sangnok-gu, Ansan-si, Gyeonggi-do 15588, Korea
7 shared publications Kiho Kim
Korea Atomic Energy Research Institute
7 shared publicationsChangsoo Han
Department of Robot Engineering, Hanyang University, Ansan, Republic of Korea
5 shared publicationsIlje Cho
5 shared publicationsJongkwang Lee
Korea Atomic Energy Research Institute, Daejeon 34057, Republic of Korea
5 shared publicationsByungsuk Park
4 shared publications
Latest Publications
- Open Access
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 41946-41963
VR-Based Teleoperation Framework: Integration of Haptic Feedback and Singularity Management
This study presents a VR-based teleoperation framework enhancing collaborative robot stability and manipulability via hand-tracking, adaptive control, and dual-modality haptic feedback. It addresses critical synchronization challenges (singularity avoidance, tracking responsiveness, and workspace constraints), which are especially problematic in first-person VR where kinematic limits are not directly perceivable. The framework employs Adaptive Damped Least Squares (A-DLS) to maintain manipulability near singular configurations, workspace impedance control to enforce boundary constraints, and vibrotactile feedback delivered through a haptic glove to convey both workspace limits (fingertip vibration) and path deviation information (wrist vibration) to operators. Key features include real-time hand-tracking, workspace calibration, and adaptive controls to ensure seamless coordination between virtual and real robot workspaces. Experimental validation through two complementary studies demonstrates the system’s effectiveness. Experiment 1 evaluated singularity management and workspace stability, showing that the A-DLS algorithm maintained manipulability above critical thresholds for 92% of operational time versus 78% without adaptive damping. Experiment 2 assessed trajectory tracking accuracy through a path-following task with 10 participants. Results demonstrate that haptic-enabled control achieves a 24.7% reduction in mean path-following error (from 10.03 mm to 7.55 mm, p = 0.001) compared to haptic-disabled conditions, indicating improvements in both accuracy and consistency. Although haptic guidance modestly increases task time due to higher precision focus, the resulting gains in accuracy and stability make this framework ideal for precision-critical tasks. By ensuring stability near workspace boundaries, the system effectively facilitates VR-based teleoperation for applications like painting, polishing, and contour-following.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 41946-41963
Open AccessVR-Based Teleoperation Framework: Integration of Haptic Feedback and Singularity Management
This study presents a VR-based teleoperation framework enhancing collaborative robot stability and manipulability via hand-tracking, adaptive control, and dual-modality haptic feedback. It addresses critical synchronization challenges (singularity avoidance, tracking responsiveness, and workspace constraints), which are especially problematic in first-person VR where kinematic limits are not directly perceivable. The framework employs Adaptive Damped Least Squares (A-DLS) to maintain manipulability near singular configurations, workspace impedance control to enforce boundary constraints, and vibrotactile feedback delivered through a haptic glove to convey both workspace limits (fingertip vibration) and path deviation information (wrist vibration) to operators. Key features include real-time hand-tracking, workspace calibration, and adaptive controls to ensure seamless coordination between virtual and real robot workspaces. Experimental validation through two complementary studies demonstrates the system’s effectiveness. Experiment 1 evaluated singularity management and workspace stability, showing that the A-DLS algorithm maintained manipulability above critical thresholds for 92% of operational time versus 78% without adaptive damping. Experiment 2 assessed trajectory tracking accuracy through a path-following task with 10 participants. Results demonstrate that haptic-enabled control achieves a 24.7% reduction in mean path-following error (from 10.03 mm to 7.55 mm, p = 0.001) compared to haptic-disabled conditions, indicating improvements in both accuracy and consistency. Although haptic guidance modestly increases task time due to higher precision focus, the resulting gains in accuracy and stability make this framework ideal for precision-critical tasks. By ensuring stability near workspace boundaries, the system effectively facilitates VR-based teleoperation for applications like painting, polishing, and contour-following.
- 15 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (5-6) , 2353-2372
Intuitive teleoperation with hand-tracking in VR: a study on master–slave system virtualization and 3D workspace visualization
- 15 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (5-6) , 2353-2372
Intuitive teleoperation with hand-tracking in VR: a study on master–slave system virtualization and 3D workspace visualization
- Open Access
- 3 January 2024
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 56 (5) , 1913-1924
Development of a dry mock-up system for verifying pyroprocess automation
- 3 January 2024
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 56 (5) , 1913-1924
Open AccessDevelopment of a dry mock-up system for verifying pyroprocess automation
- Open Access
- 24 June 2021
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2021, 1-12
Inerting Strategy for a Demonstration-Scale Hot Cell Facility Based on Experiences from Pilot-Scale Argon Cell Facility Operation and CFD Analysis
Pyroprocessing is being developed at Korea Atomic Energy Research Institute (KAERI), and in recent years, all process equipment required for integrated processes have been examined in the PyRoprocess-integrated Inactive DEmonstration (PRIDE) facility. Based on the successful operation of a pilot-scale facility, a conceptual design for this scale-up facility was actualized. Implementing a “demonstration-scale” hot cell facility is challenging as it is intended to supersede PRIDE and satisfy the increased requirements of larger-scale facilities. This study focused on an inerting strategy for a larger-scale (demonstration-scale) hot cell facility to achieve conditions equivalent to those in a pilot-scale gas-tight argon cell facility. The study applies the inerting strategy to a demonstration-scale hot cell facility beyond that of the currently existing pilot-scale hot cell facility and performs computational fluid dynamics (CFD) simulation with various flow rates to determine an appropriate approach for inerting the target facility. To this end, practical constraints on the simulation are introduced based on experiences from the existing pilot-scale facility. The results show that the purging flow rate should be accurately predicted, and a variable flow rate should be applied to achieve hot cell inerting effectively. The required purging time and amount of inerting source are essential factors in the larger-scale hot cell facility. The study results can be helpful in the design of large hot cell facilities operated under inert conditions.
- 24 June 2021
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2021, 1-12
Open AccessInerting Strategy for a Demonstration-Scale Hot Cell Facility Based on Experiences from Pilot-Scale Argon Cell Facility Operation and CFD Analysis
Pyroprocessing is being developed at Korea Atomic Energy Research Institute (KAERI), and in recent years, all process equipment required for integrated processes have been examined in the PyRoprocess-integrated Inactive DEmonstration (PRIDE) facility. Based on the successful operation of a pilot-scale facility, a conceptual design for this scale-up facility was actualized. Implementing a “demonstration-scale” hot cell facility is challenging as it is intended to supersede PRIDE and satisfy the increased requirements of larger-scale facilities. This study focused on an inerting strategy for a larger-scale (demonstration-scale) hot cell facility to achieve conditions equivalent to those in a pilot-scale gas-tight argon cell facility. The study applies the inerting strategy to a demonstration-scale hot cell facility beyond that of the currently existing pilot-scale hot cell facility and performs computational fluid dynamics (CFD) simulation with various flow rates to determine an appropriate approach for inerting the target facility. To this end, practical constraints on the simulation are introduced based on experiences from the existing pilot-scale facility. The results show that the purging flow rate should be accurately predicted, and a variable flow rate should be applied to achieve hot cell inerting effectively. The required purging time and amount of inerting source are essential factors in the larger-scale hot cell facility. The study results can be helpful in the design of large hot cell facilities operated under inert conditions.
- 21 June 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 116 (1-2) , 487-505
Virtual reality platform-based conceptual design and simulation of a hot cell facility
- 21 June 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 116 (1-2) , 487-505
Virtual reality platform-based conceptual design and simulation of a hot cell facility
- Open Access
- 16 July 2019
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2019, 1-10
A Conceptual Framework for Equipment Maintenance Automation under a Pyroprocessing Automation Framework
For most of the remote maintenance activities of equipment in a hot cell, replacing breakdown modules is preferred over in situ repair because of insufficient space in the cell and the limited operability of remote handling tools. In such cases, the maintenance operation can be decomposed into transport of the new modules to the failed equipment, replacement of the broken modules with new ones, and then transport of the broken parts to the reserved space for further repair or disposal. In this respect, transfer is the most basic operation during remote maintenance, which is also true for the maintenance of pyroprocessing equipment. Hence, this paper proposes a maintenance automation framework for automated pyroprocessing equipment from the standpoint of module transfer. For the maintenance automation framework, maintenance-related functions and events are defined, and they are integrated with the pyroprocess automation framework. The proposed framework is verified by a case study on the maintenance of a large module through a hardware-in-the-loop simulation.
- 16 July 2019
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2019, 1-10
Open AccessA Conceptual Framework for Equipment Maintenance Automation under a Pyroprocessing Automation Framework
For most of the remote maintenance activities of equipment in a hot cell, replacing breakdown modules is preferred over in situ repair because of insufficient space in the cell and the limited operability of remote handling tools. In such cases, the maintenance operation can be decomposed into transport of the new modules to the failed equipment, replacement of the broken modules with new ones, and then transport of the broken parts to the reserved space for further repair or disposal. In this respect, transfer is the most basic operation during remote maintenance, which is also true for the maintenance of pyroprocessing equipment. Hence, this paper proposes a maintenance automation framework for automated pyroprocessing equipment from the standpoint of module transfer. For the maintenance automation framework, maintenance-related functions and events are defined, and they are integrated with the pyroprocess automation framework. The proposed framework is verified by a case study on the maintenance of a large module through a hardware-in-the-loop simulation.
- 1 December 2018
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 36 (12) , 1822-1835
Design analysis and optimization of 6-DOF telemanipulator based on performance indices
In contrast to general industrial robots, which are operated in normal environments and are easily accessible by human workers, telemanipulators are typically designed to perform specific and extreme tasks in hazardous areas. Teleoperation systems are difficult-to-equip fully intuitive or automated control systems because these are the kinds of manipulator systems used as substitutes to perform tasks that humans have to guide directly because they may require tough, sensitive, or sophisticated handling motions. Basically, these kinds of tasks are difficult to remotely perform through a slave manipulator operated by a human unless modification and optimization of the system are conducted. In this regard, the target system dealt within this study has similar disadvantages even though it has a high degree of freedom (DOF) arm structure. The performance of the current system was quantitatively evaluated to optimize the structure according to the considered main tasks. This work presents the various performance indices utilized and analyzes the current design of the considered telemanipulator system. An optimal design approach using the parameters associated with the frequent motions of the considered 6-DOF telemanipulator is then proposed based on the conducted analyses.
- 1 December 2018
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 36 (12) , 1822-1835
Design analysis and optimization of 6-DOF telemanipulator based on performance indices
In contrast to general industrial robots, which are operated in normal environments and are easily accessible by human workers, telemanipulators are typically designed to perform specific and extreme tasks in hazardous areas. Teleoperation systems are difficult-to-equip fully intuitive or automated control systems because these are the kinds of manipulator systems used as substitutes to perform tasks that humans have to guide directly because they may require tough, sensitive, or sophisticated handling motions. Basically, these kinds of tasks are difficult to remotely perform through a slave manipulator operated by a human unless modification and optimization of the system are conducted. In this regard, the target system dealt within this study has similar disadvantages even though it has a high degree of freedom (DOF) arm structure. The performance of the current system was quantitatively evaluated to optimize the structure according to the considered main tasks. This work presents the various performance indices utilized and analyzes the current design of the considered telemanipulator system. An optimal design approach using the parameters associated with the frequent motions of the considered 6-DOF telemanipulator is then proposed based on the conducted analyses.
- Open Access
- 1 December 2017
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 49 (8) , 1717-1726
Design considerations for teleoperation systems operating in gas-tight argon cells
- 1 December 2017
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 49 (8) , 1717-1726
Open AccessDesign considerations for teleoperation systems operating in gas-tight argon cells
- Open Access
- 19 October 2017
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2017, 1-11
Equipment Layout Improvement for Large-Scale Hot Cell Facility Logistics
This study presents approaches to equipment layout improvement for a large-scale hot cell facility. First, the original facility layout and target process are introduced, including the basic information and specifications. Second, the flow of process materials is analyzed and the relationships are evaluated in detail using a “from-to chart” and a “relationship chart” for the original layout, and the logistics are simulated using the selected discrete event simulator to calculate the traveling distances of process materials handled by teleoperated material handling systems. Third, the original layout is modified using the total closeness rating (TCR), and the efficiency and usage of the material handling system are calculated and compared with the original case to evaluate the efficiency improvement of the modified layout. This modification process, which included load reduction, enabled those aspects of the material handling system that would need to be changed to be identified; these changes were suggested by a quantitative analysis of the logistics between each pair of stations and intuitive rearrangement based on charts and figures. These approaches could be an initial step in the large-scale hot cell design process, with future work to follow.
- 19 October 2017
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2017, 1-11
Open AccessEquipment Layout Improvement for Large-Scale Hot Cell Facility Logistics
This study presents approaches to equipment layout improvement for a large-scale hot cell facility. First, the original facility layout and target process are introduced, including the basic information and specifications. Second, the flow of process materials is analyzed and the relationships are evaluated in detail using a “from-to chart” and a “relationship chart” for the original layout, and the logistics are simulated using the selected discrete event simulator to calculate the traveling distances of process materials handled by teleoperated material handling systems. Third, the original layout is modified using the total closeness rating (TCR), and the efficiency and usage of the material handling system are calculated and compared with the original case to evaluate the efficiency improvement of the modified layout. This modification process, which included load reduction, enabled those aspects of the material handling system that would need to be changed to be identified; these changes were suggested by a quantitative analysis of the logistics between each pair of stations and intuitive rearrangement based on charts and figures. These approaches could be an initial step in the large-scale hot cell design process, with future work to follow.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1851-1853
Selecting telemanipulators for hazardous task in a radioactive area
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1851-1853
Selecting telemanipulators for hazardous task in a radioactive area