Christopher Mark Johnson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Christopher Mark Johnson has a total of 599 co-authors. Here are the top co-authors by number of shared publications:
- Nicholas G. Wright
School of Engineering, Newcastle University, Newcastle upon Tyne, U.K.
28 shared publications - Alberto Castellazzi
Kyoto University of Advanced Science
22 shared publications - Jian Feng Li
Department of Electrical and Electronic Engineering, University of Nottingham, Nottingham, U.K.
20 shared publications - Anthony G. O'Neill
School of Engineering, Newcastle University, Newcastle upon Tyne, U.K.
12 shared publications Alton B. Horsfall
Newcastle University
11 shared publicationsKonstantin Vassilevski
Newcastle University
11 shared publications
Latest Publications
- Open Access
- 27 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (4) , 4068-4076
Development and Validation of a Smart Architecture for Thyristor Valves
A high voltage thyristor converter is realized by many valve sections, whose volume is approximately occupied for only the 10% by thyristors and for the 10% by the relevant gate drivers. The remaining 80% is taken by passive auxiliary circuits, needed to protect thyristors during turn-on and turn-off commutations. This work represents a preliminary validation of an innovative architecture that aims to reduce the auxiliary circuit cost, volume, and weight of the overall valve, through the investigation of active, instead of passive solutions. The work starts from investigation of the phenomena behind the valve transient behaviors and proceeds with simulations and experimental tests, using a reduced scale circuit prototype. The match between the obtained results validates the investigated active configurations, confirming that the proposed solution can be used for improving thyristor valves.
- 27 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (4) , 4068-4076
Open AccessDevelopment and Validation of a Smart Architecture for Thyristor Valves
A high voltage thyristor converter is realized by many valve sections, whose volume is approximately occupied for only the 10% by thyristors and for the 10% by the relevant gate drivers. The remaining 80% is taken by passive auxiliary circuits, needed to protect thyristors during turn-on and turn-off commutations. This work represents a preliminary validation of an innovative architecture that aims to reduce the auxiliary circuit cost, volume, and weight of the overall valve, through the investigation of active, instead of passive solutions. The work starts from investigation of the phenomena behind the valve transient behaviors and proceeds with simulations and experimental tests, using a reduced scale circuit prototype. The match between the obtained results validates the investigated active configurations, confirming that the proposed solution can be used for improving thyristor valves.
- 6 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 21 (4) , 536-543
Reliability and Characterization of Nanosilver Joints Prepared by a Time-Reduced Sintering Process
This study investigates the power cycling reliability of nanosilver sintered joints formed by a time-reduced sintering process, designed for use on a die bonder. A range of sintering parameters, reflecting different levels of manufacturability, were used to produce sintered joints in respect of shear strength and porosity, within a process cycle time of a few seconds. The reliability of the sintered attachments were evaluated against Pb5Sn solder joints under constant temperature swing power cycling conditions over the range 50 to 200 °C. The thermal performance and microstructural changes of the sintered joints were monitored and evaluated non-destructively at regular intervals using transient thermal impedance and X-ray computed tomography. The results show that sintered joints with higher shear strengths (>50 MPa) and lower porosities (<25 %) tend to maintain their thermal performance up to ~100k power cycles before gradual degradation occurs. Sintered joints with intermediate shear strengths (20 to 40 MPa) and with corresponding analogous porosities (35 to 51 %) also demonstrated comparable power cycling behavior; exhibiting a progressive decrease in effective thermal conductivity with increasing cycles. The evaluated lifetime of sintered joints with the highest shear strengths were found to be at least double those for the lower shear strength joints, and up to fourteen times those of a Pb5Sn solder die attachment. Even the most porous sintered joints exhibited lifetimes appreciably longer than a Pb5Sn die attachment. Degradation in thermal resistance was seen to correlate with observed microstructural changes, with a dependence on initial sintering parameters.
- 6 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 21 (4) , 536-543
Reliability and Characterization of Nanosilver Joints Prepared by a Time-Reduced Sintering Process
This study investigates the power cycling reliability of nanosilver sintered joints formed by a time-reduced sintering process, designed for use on a die bonder. A range of sintering parameters, reflecting different levels of manufacturability, were used to produce sintered joints in respect of shear strength and porosity, within a process cycle time of a few seconds. The reliability of the sintered attachments were evaluated against Pb5Sn solder joints under constant temperature swing power cycling conditions over the range 50 to 200 °C. The thermal performance and microstructural changes of the sintered joints were monitored and evaluated non-destructively at regular intervals using transient thermal impedance and X-ray computed tomography. The results show that sintered joints with higher shear strengths (>50 MPa) and lower porosities (<25 %) tend to maintain their thermal performance up to ~100k power cycles before gradual degradation occurs. Sintered joints with intermediate shear strengths (20 to 40 MPa) and with corresponding analogous porosities (35 to 51 %) also demonstrated comparable power cycling behavior; exhibiting a progressive decrease in effective thermal conductivity with increasing cycles. The evaluated lifetime of sintered joints with the highest shear strengths were found to be at least double those for the lower shear strength joints, and up to fourteen times those of a Pb5Sn solder die attachment. Even the most porous sintered joints exhibited lifetimes appreciably longer than a Pb5Sn die attachment. Degradation in thermal resistance was seen to correlate with observed microstructural changes, with a dependence on initial sintering parameters.
- 1 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 724-737
Optimal Integrated Design of a Magnetically Coupled Interleaved H-Bridge
The application of wide-band gap semiconductors and their integration with other power electronics components (e.g., passives, gate drivers, sensing, thermal management) can meet the growing demand for volume reduction in power electronics systems. The design of such an integrated system is a complex multiphysics problem given the high number of variables to identify, objectives to optimize, and constraints to satisfy. Traditionally, this complex problem is approached subdividing the design in different steps, where in each step, the single components are designed and optimized independently from the others. This might clearly overlook the effect that the design choices of a single subsystem has on other subsystems, leading to suboptimal solutions. In this article, an automated design approach is proposed with the aim of maximizing power density whilst minimizing total losses. As a vessel to investigate the presented optimization workflow, the magnetically coupled interleaved H-bridge topology is chosen as an emblematic example of multivariable design problem. The first step of this approach consists of developing a loss model of the converter, which takes into account components physical dimensions, the temperature dependence, and the circuit parasitics. In the second step, these models are used within a nested optimization procedure in order to estimate the losses for multiple points of load. With the aim of validating both design approach and optimization results, three different optimal solutions have been deeply analyzed with commercial suit, prototyped, and tested. The showed experimental results endorse the adopted design approach confirming the optimality/validity of the manufactured solutions.
- 1 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (1) , 724-737
Optimal Integrated Design of a Magnetically Coupled Interleaved H-Bridge
The application of wide-band gap semiconductors and their integration with other power electronics components (e.g., passives, gate drivers, sensing, thermal management) can meet the growing demand for volume reduction in power electronics systems. The design of such an integrated system is a complex multiphysics problem given the high number of variables to identify, objectives to optimize, and constraints to satisfy. Traditionally, this complex problem is approached subdividing the design in different steps, where in each step, the single components are designed and optimized independently from the others. This might clearly overlook the effect that the design choices of a single subsystem has on other subsystems, leading to suboptimal solutions. In this article, an automated design approach is proposed with the aim of maximizing power density whilst minimizing total losses. As a vessel to investigate the presented optimization workflow, the magnetically coupled interleaved H-bridge topology is chosen as an emblematic example of multivariable design problem. The first step of this approach consists of developing a loss model of the converter, which takes into account components physical dimensions, the temperature dependence, and the circuit parasitics. In the second step, these models are used within a nested optimization procedure in order to estimate the losses for multiple points of load. With the aim of validating both design approach and optimization results, three different optimal solutions have been deeply analyzed with commercial suit, prototyped, and tested. The showed experimental results endorse the adopted design approach confirming the optimality/validity of the manufactured solutions.
- Open Access
A GaN-HEMT Compact Model Including Dynamic RDSon Effect for Power Electronics Converters
In order to model GaN-HEMT switching transients and determine power losses, a compact model including dynamic effect is proposed herein. The model includes mathematical equations to represent device static and capacitance-voltage characteristics, and a behavioural voltage source, which includes multiple RC units to represent different time constants for trapping and detrapping effect from 100 ns to 100 s range. All the required parameters in the model can be obtained by fitting method using a datasheet or experimental characterisation results. The model is then implemented into our developed virtual prototyping software, where the device compact model is co-simulated with a parasitic inductance physical model to obtain the switching waveform. As model order reduction is applied in our software to resolve physical model, the device switching current and voltage waveform can be obtained in the range of minutes. By comparison with experimental measurements, the model is validated to accurately represent device switching transients as well as their spectrum in frequency domain until 100 MHz. In terms of dynamic value, the mismatch between the model and experimental results is within 10% under different power converter operation conditions in terms of switching frequencies and duty cycles, so designers can use this model to accurately obtain GaN-HEMT power losses due to trapping and detrapping effects for power electronics converters.Open AccessA GaN-HEMT Compact Model Including Dynamic RDSon Effect for Power Electronics Converters
In order to model GaN-HEMT switching transients and determine power losses, a compact model including dynamic effect is proposed herein. The model includes mathematical equations to represent device static and capacitance-voltage characteristics, and a behavioural voltage source, which includes multiple RC units to represent different time constants for trapping and detrapping effect from 100 ns to 100 s range. All the required parameters in the model can be obtained by fitting method using a datasheet or experimental characterisation results. The model is then implemented into our developed virtual prototyping software, where the device compact model is co-simulated with a parasitic inductance physical model to obtain the switching waveform. As model order reduction is applied in our software to resolve physical model, the device switching current and voltage waveform can be obtained in the range of minutes. By comparison with experimental measurements, the model is validated to accurately represent device switching transients as well as their spectrum in frequency domain until 100 MHz. In terms of dynamic value, the mismatch between the model and experimental results is within 10% under different power converter operation conditions in terms of switching frequencies and duty cycles, so designers can use this model to accurately obtain GaN-HEMT power losses due to trapping and detrapping effects for power electronics converters. - Open Access
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (9) , 9650-9660
Accurate Measurement of Dynamic on-State Resistances of GaN Devices Under Reverse and Forward Conduction in High Frequency Power Converter
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (9) , 9650-9660
Open AccessAccurate Measurement of Dynamic on-State Resistances of GaN Devices Under Reverse and Forward Conduction in High Frequency Power Converter
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (4) , 3867-3876
Heterogeneous Integration of Magnetic Component Windings on Ceramic Substrates
Heterogeneous integration and the converter in package concept have been highlighted as enabling technologies to unlock the full potential of Silicon Carbide (SiC) and Gallium Nitride (GaN) devices. Control of parasitic elements in the commutation loops and passive filter integration within the power module reduce the risk of over-current and over-voltage stresses for the transistors and can improve the containment of high frequency noise at source, resulting in a safer operation of the whole converter. However, at present, the major limitation to filter integration is posed by the low energy density of commercial magnetic components. This paper shows further investigating on the integration of more reliable high power density magnetic components within the power module structure. The proposed approach consists of bonding individual copper parts, representative of single winding turns, onto an appropriately patterned ceramic substrate, thus improving the filters thermal management. At first, an experimental comparison between different bonding techniques has been carried out on the basis of mechanical performance. Finally, to prove the feasibility and repeatability of the proposed route, a complete inductor has been manufactured using solder bonding technique. Both thermal tests and simulations confirmed, that thanks to the enhanced heat exchange between inductor and cooling system, the maximum current density can be increased above commercial standards, while maintaining the temperature in a safe range for the nearby active devices.
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (4) , 3867-3876
Heterogeneous Integration of Magnetic Component Windings on Ceramic Substrates
Heterogeneous integration and the converter in package concept have been highlighted as enabling technologies to unlock the full potential of Silicon Carbide (SiC) and Gallium Nitride (GaN) devices. Control of parasitic elements in the commutation loops and passive filter integration within the power module reduce the risk of over-current and over-voltage stresses for the transistors and can improve the containment of high frequency noise at source, resulting in a safer operation of the whole converter. However, at present, the major limitation to filter integration is posed by the low energy density of commercial magnetic components. This paper shows further investigating on the integration of more reliable high power density magnetic components within the power module structure. The proposed approach consists of bonding individual copper parts, representative of single winding turns, onto an appropriately patterned ceramic substrate, thus improving the filters thermal management. At first, an experimental comparison between different bonding techniques has been carried out on the basis of mechanical performance. Finally, to prove the feasibility and repeatability of the proposed route, a complete inductor has been manufactured using solder bonding technique. Both thermal tests and simulations confirmed, that thanks to the enhanced heat exchange between inductor and cooling system, the maximum current density can be increased above commercial standards, while maintaining the temperature in a safe range for the nearby active devices.
- Top Cited Papers
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6050-6060
10-kV SiC MOSFET Power Module With Reduced Common-Mode Noise and Electric Field
The advancement of silicon carbide (SiC) power devices with voltage ratings exceeding 10 kV is expected to revolutionize medium- and high-voltage systems. However, present power module packages are limiting the performance of these unique switches. The objective of this research is to push the boundaries of high-density, high-speed, 10 kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10 kV devices. The high-speed switching and high voltage rating of these devices causes significant EMI and high electric field. Existing power module packages are unable to address these challenges, resulting in detrimental EMI and partial discharge that limit the converter operation. This paper presents the design and testing of a 10 kV SiC MOSFET power module that switches at a record 250 V/ns without compromising the signal and ground integrity due to an integrated screen reduces the common-mode current by ten times. This screen connection simultaneously increases the partial discharge inception voltage by more than 50 %. With the integrated cooling system, the power module prototype achieves a power density of 4 W/mm3.
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6050-6060
Top Cited Papers10-kV SiC MOSFET Power Module With Reduced Common-Mode Noise and Electric Field
The advancement of silicon carbide (SiC) power devices with voltage ratings exceeding 10 kV is expected to revolutionize medium- and high-voltage systems. However, present power module packages are limiting the performance of these unique switches. The objective of this research is to push the boundaries of high-density, high-speed, 10 kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10 kV devices. The high-speed switching and high voltage rating of these devices causes significant EMI and high electric field. Existing power module packages are unable to address these challenges, resulting in detrimental EMI and partial discharge that limit the converter operation. This paper presents the design and testing of a 10 kV SiC MOSFET power module that switches at a record 250 V/ns without compromising the signal and ground integrity due to an integrated screen reduces the common-mode current by ten times. This screen connection simultaneously increases the partial discharge inception voltage by more than 50 %. With the integrated cooling system, the power module prototype achieves a power density of 4 W/mm3.
- 27 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (1) , 381-394
Design and Experimental Validation of a Wire-Bond-Less 10-kV SiC MOSFET Power Module
Wide bandgap (WBG) power devices with voltage ratings exceeding 10 kV have the potential to revolutionize medium- and high-voltage systems due to their high-speed switching and lower ON-state losses. However, the present power module packages are limiting the performance of these unique switches. The objective of this article is to push the boundaries of high-density, high-speed, 10-kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10-kV devices. The module achieves low and balanced parasitic inductances, resulting in a record switching speed of 250 V/ns with negligible ringing and voltage overshoot. An integrated screen reduces the common-mode (CM) current that is generated by these fast voltage transients by ten times. This screen connection simultaneously increases the partial discharge inception voltage (PDIV) by more than 50%. A compact, medium-voltage termination and system interface design is also proposed in this article. With the integrated jet-impingement cooler, the power module prototype achieves a power density of 4 W/mm 3 . This article presents the design, prototyping, and testing of this optimized package for 10-kV SiC MOSFETs.
- 27 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (1) , 381-394
Design and Experimental Validation of a Wire-Bond-Less 10-kV SiC MOSFET Power Module
Wide bandgap (WBG) power devices with voltage ratings exceeding 10 kV have the potential to revolutionize medium- and high-voltage systems due to their high-speed switching and lower ON-state losses. However, the present power module packages are limiting the performance of these unique switches. The objective of this article is to push the boundaries of high-density, high-speed, 10-kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10-kV devices. The module achieves low and balanced parasitic inductances, resulting in a record switching speed of 250 V/ns with negligible ringing and voltage overshoot. An integrated screen reduces the common-mode (CM) current that is generated by these fast voltage transients by ten times. This screen connection simultaneously increases the partial discharge inception voltage (PDIV) by more than 50%. A compact, medium-voltage termination and system interface design is also proposed in this article. With the integrated jet-impingement cooler, the power module prototype achieves a power density of 4 W/mm 3 . This article presents the design, prototyping, and testing of this optimized package for 10-kV SiC MOSFETs.
- 1 November 2018
- Published by Elsevier in Journal of Minimally Invasive Gynecology
- Vol. 25 (7) , S188
Transfusion in Gynecologic Surgery
- 1 November 2018
- Published by Elsevier in Journal of Minimally Invasive Gynecology
- Vol. 25 (7) , S188
Transfusion in Gynecologic Surgery
- 1 October 2018
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2018 (1) , 000069-000074
Converter-Level Integration for Wide Band-Gap Automotive Power Electronics
Wide band-gap (WBG) semiconductors offer many potential benefits to designers of power electronic systems. Lower switching losses allow operation at higher switching frequencies, which in principle allows a reduction in passive component values in many converter applications. However, efficient operation at higher switching frequencies requires increased voltage and current transition rates. With conventional packaging and circuit construction, parasitic inductance and capacitance can deteriorate converter performance, reducing efficiency and adding to the electromagnetic interference (EMI) emitted from the system. Outside the commutation cell, fast voltage transitions may lead to unacceptably high levels of conducted and radiated EMI, so approaches involving the local filtering of converter outputs are attractive. To mitigate these effects in conventional modules, switching speeds are often deliberately limited and the potential benefits of using WBG technologies cannot be fully realized. Here we examine the design and realization of Converter-in-Package (CiP) modular blocks for system power levels from 100s W to 100s kW, incorporating individual commutation cells with close-coupled gate drives, input/output filtering and reduced EMI. The concept is illustrated through the realization of a modular, segmented power converter for an integrated drive.
- 1 October 2018
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2018 (1) , 000069-000074
Converter-Level Integration for Wide Band-Gap Automotive Power Electronics
Wide band-gap (WBG) semiconductors offer many potential benefits to designers of power electronic systems. Lower switching losses allow operation at higher switching frequencies, which in principle allows a reduction in passive component values in many converter applications. However, efficient operation at higher switching frequencies requires increased voltage and current transition rates. With conventional packaging and circuit construction, parasitic inductance and capacitance can deteriorate converter performance, reducing efficiency and adding to the electromagnetic interference (EMI) emitted from the system. Outside the commutation cell, fast voltage transitions may lead to unacceptably high levels of conducted and radiated EMI, so approaches involving the local filtering of converter outputs are attractive. To mitigate these effects in conventional modules, switching speeds are often deliberately limited and the potential benefits of using WBG technologies cannot be fully realized. Here we examine the design and realization of Converter-in-Package (CiP) modular blocks for system power levels from 100s W to 100s kW, incorporating individual commutation cells with close-coupled gate drives, input/output filtering and reduced EMI. The concept is illustrated through the realization of a modular, segmented power converter for an integrated drive.