Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Giovanni Grasso has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dynamic Reliability Analysis of Rotary Atomizer Spray Dryers: A Hybrid Fault Tree and Markov Approach for Risk‐Informed Maintenance

    by Ludovica Maria Oliveri, Ferdinando Chiacchio, Giovanni Maria Grasso, Fabio Famoso, Natalia Trapani

    This paper presents a quantitative reliability analysis of a rotary atomizer spray‐drying line, used here as a representative application of complex rotating process equipment. A Static Fault Tree (SFT) Analysis models four primary failure modes: mechanical degradation, tower over‐temperature, feed loss with missed cleaning and undetected airflow loss. The analysis is extended to a Dynamic Fault Tree (DFT) framework that captures temporal ordering, standby behaviour and demand‐dependent failures through dynamic gates, and is quantitatively evaluated via a hierarchical Continuous‐Time Markov Chain (CTMC) approach. The integration of DFTs and CTMCs is a mature research stream; however, fewer studies show how to apply a selective DFT–CTMC refinement to industrial process equipment while preserving fault‐tree interpretability for engineering decision making. The contribution of this work specifically lies in using a targeted SFT–DFT–CTMC refinement strategy in which only the branches whose physical behaviour requires temporal or demand‐dependent modelling are converted into local Markov modules, while the upper‐level fault‐tree structure remains readable and reusable for maintenance prioritisation. Based on this framework, two mission time horizons are examined: a short‐term period representing operational campaigns between cleaning‐in‐place cycles and a long‐term period representative of the atomizer's operational lifetime. Results show that the SFT provides a conservative upper bound, overestimating the top‐event probability by approximately 40%–70% relative to the DFT, with potential distortion of importance rankings. By filtering dynamically implausible sequences, the DFT–CTMC model emphasises protection and diagnostic subsystems and supports risk‐informed design and maintenance priorities through time‐dependent importance (Fussell–Vesely) and sensitivity analyses. The proposed hybrid hierarchical workflow is transferable to other rotating process assets featuring protection chains and demand‐driven actions.

  • Open Access

    Simulation-Based Structural Optimization of Composite Hulls Under Slamming Loads: A Transferable Methodology for Resilient Offshore Applications

    by Giovanni Maria Grasso, Ludovica Maria Oliveri, Ferdinando Chiacchio

    The growing demand for floating offshore structures calls for lightweight, impact-resilient, and sustainable design approaches. This study explores the optimization of composite fibree layup in a 30 m hull subjected to slamming-type hydrodynamic loads. Although based on a recreational vessel, the model serves as a transferable case for offshore applications such as wave energy devices, offshore wind platforms, and floating PV systems. A finite element method (FEM) model was developed using shell elements and a sinusoidal time-dependent pressure to simulate slamming events on the wet surface of the hull. The response was evaluated under different fiber orientation schemes, aiming to reduce structural mass while maintaining stress levels within safety margins. Results showed that strategic layup optimization led to a measurable reduction in total material usage, without compromising structural integrity. These outcomes suggest multiple advantages, including an approximately 14% reduction in raw material demand, which in turn facilitates for potential downsizing of propulsion systems and transportation energy due to lighter structures. Such improvements contribute indirectly to reduced emissions and operational costs. The methodology presented offers a replicable approach to composite optimization under transient marine loads, with relevance for sustainable offshore structural design.


  • Open Access

    Structural Analysis and Redrawing of a Sailing Catamaran with a Numerical and Experimental Approach

    by Giovanni Maria Grasso, Marco Bonfanti, Fabio Lo Savio, Damiano Alizzio, Ferdinando Chiacchio

    This study investigates the structural behavior of a sailing catamaran subjected to wind, wave, and self-weight loads, with the ultimate goal of improving the structural design through redrawing techniques. A digital model was developed using Creo software 6 and analyzed through Finite Element Analysis (FEA), complemented by experimental deformation tests conducted under dry conditions and controlled loading. These tests provided a reliable dataset for calibrating and validating the numerical model. The analysis focused on the structural responses of key components—such as bulkheads, hulls, and beam-to-hull connections—under both isolated as well as combined load scenarios. Most structural elements demonstrated low deformation, confirming the robustness of the design; however, stress concentrations were observed at the connecting plates, highlighting areas for improvement. The vessel’s overall stiffness, though advantageous for structural integrity, was identified as a constraint in weight redrawing efforts. Consequently, targeted structural modifications were proposed and implemented, resulting in reduced material usage, construction time, and overall costs. The study concludes by proposing the integration of advanced composite materials to further enhance performance and efficiency, thereby laying the groundwork for future integration with digital and structural health monitoring systems.


  • Open Access

    Numerical–Experimental Analysis to Optimize the Geometry of a Prosthetic Abutment

    by Giovanni M. Grasso, Marco Bonfanti, Damiano Alizzio, Fabio Lo Savio

    This paper aims to identify methods for optimizing the geometry of dental prosthesis preparation, through both an analytical study and a numerical investigation. Assuming a 10° inclined load with respect to the median sagittal plane, a double algorithm was developed that was capable of calculating the axial resistance area and the cusp resistance area (if present) of a prosthetic abutment as the main geometric parameters vary. In particular, a coupling model with a pseudo-elliptical base was proposed, which is better than the circular shape representing the real shape assumed by the abutment following the dental intervention. The model also allows the presence of a cusp. This model was first analyzed using FEA, also simulating the presence of coupling cement between the abutment and the crown, and then physically made with a 10:1 scale prototype. The convergence of the experimental results found with the numerical–theoretical studies is an indication of the validity of the proposed model. A key contribution of this research using the proposed algorithm allowed to demonstrate that a superior limit of 0.25 for the ratio (HR) between the heights of the cusp sulcus (h-hc) and the abutment (h) is required to achieve good stability of the coupling. The methodology developed in this study is applicable to a variety of teeth, making it versatile and highly adaptable for broader clinical applications.

  • Open Access

    Low cost UV-induced fluorescence sensor for monitoring aromatic hydrocarbons in coastal marine water

    by Fabio Lo Savio, Giovanni Grasso, Giuseppe Maccarrone

    Nowadays the coastal waters of the Mediterranean Sea are increasingly affected by pollution from aromatic hydrocarbons. Therefore, in order to implement damage minimization actions, a continuous monitoring system with rapid response is needed. The most effective local method for distinguishing aromatic hydrocarbons from salt water is UV-induced fluorescence. This paper describes the design and building of a UV-induced fluorescence sensor that, mounted on board a sensor-buoy, detects the presence or absence of the pollutant in any atmospheric condition. The sensor consists of a measuring chamber, in which the water, loaded by a submersible pump, maintains a constant level thanks to a small siphon. The detection system, consisting of a UVC-LED and a phototransistor that responds in the visible light band, is located in the upper part of the chamber. In vitro tests, performed by comparing the sensor results with those obtained from a spectrofluorometer, have shown good sensitivity, repeatability, and accuracy, despite the inexpensiveness and low energy consumption of the sensor. An important goal achieved by the design and building methodology is that the sensor is able to withstand harsh weather conditions, the corrosive action of salt water and biofouling.


  • Open Access

    Experimental and numerical analysis of quench propagation on MgB2tapes and pancake coils

    by J Pelegrín, G Romano, E Martínez, L A Angurel, R Navarro, C Ferdeghini, S Brisigotti, G Grasso, D Nardelli


  • BLADDER TISSUE RESPONSE TO PHYSIOLOGICAL STATIC AND DYNAMIC LOADS

    by Elisabetta M Zanetti, Michela Perrini, Giovanni Grasso, C Bignardi, Alberto L. Audenino

  • Long Length MgB2 Conductors for Industrial Applications

    by A. Malagoli, Giovanni Grasso, Maurizio Vignolo, Andrea Tumino, V. Braccini, Cristina Bernini, M. Tropeano, A.S. Siri, Davide Nardelli, Marco Modica

    In spite of the relatively short time dedicated to the development of MgB2 conductors since its discovery in 2001, a remarkable progress has been already achieved in terms of critical current density, homogeneity of the conductors and reproducibility of the results over long lengths. Unlike other HTS and LTS materials, MgB2 conductor processing is more open to a number of improvements and modifications that help in making it more attractive for several DC and AC applications. Up to now our work has been focused on the improvement of the production capacity in order to allow for the assembly of large prototype magnets to test the capability of MgB2 to maintain the present level of performance over very long lengths. Long MgB2 tapes of about 1600 m with superconducting and mechanical properties suitable for making low field magnets are already available. Presently we are focusing on the enhancement of the irreversibility field. This would open the possibility of using MgB2 also for high field applications.