Seval Oren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seval Oren has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Liang Dong
Department of Electrical and Computer Engineering Iowa State University Ames IA 50011 USA
6 shared publications- Liang Dong
University of Georgia
4 shared publications - Halil Ceylan
Iowa State University
3 shared publications - Qiugu Wang
Department of Electrical and Computer Engineering, Iowa State University, Ames, USA
3 shared publications Shawana Tabassum
Department of Electrical and Computer Engineering, Iowa State University, Ames, USA
3 shared publicationsYifei Wang
Department of Electrical and Computer Engineering, Iowa State University, Ames, Iowa, USA
3 shared publications
Latest Publications
- 17 November 2017
- Published by Wiley in Advanced Materials Technologies
- Vol. 2 (12)
High‐Resolution Patterning and Transferring of Graphene‐Based Nanomaterials onto Tape toward Roll‐to‐Roll Production of Tape‐Based Wearable Sensors
This paper reports on a simple and versatile method for patterning and transferring graphene‐based nanomaterials onto various types of tape to realize flexible microscale sensors. The method involves drop‐casting a graphene film on a prepatterned polydimethylsiloxane (PDMS) surface containing negative features by graphene suspensions, applying Scotch tape to remove the excess graphene from the nonpatterned areas of the PDMS surface, and then transferring the patterned graphene from the inside of the negative features at the PDMS surface onto a target tape. The feature size of transferred graphene patterns on the final tape is as small as a few micrometers. This method is easy to implement, but does not require the use of expensive equipment, except for needing a PDMS substrate containing negative features. This method has a high versatility in producing micropatterns of graphene‐based nanomaterials on different types of adhesive tape. For the purpose of application demonstration, flexible mechanical sensors and sensor arrays, smart gloves, and plant leaf sensors on tapes to realize real‐time monitoring of important signals indicating human motion and plant water transport behavior have been developed. This technology will open a new route for low‐cost, scalable, and roll‐to‐roll production of graphene‐based sensors on tape.
- 17 November 2017
- Published by Wiley in Advanced Materials Technologies
- Vol. 2 (12)
High‐Resolution Patterning and Transferring of Graphene‐Based Nanomaterials onto Tape toward Roll‐to‐Roll Production of Tape‐Based Wearable Sensors
This paper reports on a simple and versatile method for patterning and transferring graphene‐based nanomaterials onto various types of tape to realize flexible microscale sensors. The method involves drop‐casting a graphene film on a prepatterned polydimethylsiloxane (PDMS) surface containing negative features by graphene suspensions, applying Scotch tape to remove the excess graphene from the nonpatterned areas of the PDMS surface, and then transferring the patterned graphene from the inside of the negative features at the PDMS surface onto a target tape. The feature size of transferred graphene patterns on the final tape is as small as a few micrometers. This method is easy to implement, but does not require the use of expensive equipment, except for needing a PDMS substrate containing negative features. This method has a high versatility in producing micropatterns of graphene‐based nanomaterials on different types of adhesive tape. For the purpose of application demonstration, flexible mechanical sensors and sensor arrays, smart gloves, and plant leaf sensors on tapes to realize real‐time monitoring of important signals indicating human motion and plant water transport behavior have been developed. This technology will open a new route for low‐cost, scalable, and roll‐to‐roll production of graphene‐based sensors on tape.
- 17 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 1 (6) , 1-4
Helical-Shaped Graphene Tubular Spring Formed Within Microchannel for Wearable Strain Sensor With Wide Dynamic Range
This article reports on a helical spring-like piezoresistive graphene strain sensor formed within a microfluidic channel. The helical spring has a tubular hollow structure and is made of a thin graphene layer coated on the inner wall of the channel using an in situ microfluidic casting method. The helical shape allows the sensor to flexibly respond to both tensile and compressive strains in a wide dynamic detection range from 24 compressive strain to 20 tensile strain. Fabrication of the sensor involves embedding a helical thin metal wire with a plastic wrap into a precursor solution of an elastomeric polymer, forming a helical microfluidic channel by removing the wire from cured elastomer, followed by microfluidic casting of a graphene thin layer directly inside the helical channel. The wide dynamic range, in conjunction with mechanical flexibility and stretchability of the sensor, will enable practical wearable strain sensor applications where large strains are often involved.
- 17 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 1 (6) , 1-4
Helical-Shaped Graphene Tubular Spring Formed Within Microchannel for Wearable Strain Sensor With Wide Dynamic Range
This article reports on a helical spring-like piezoresistive graphene strain sensor formed within a microfluidic channel. The helical spring has a tubular hollow structure and is made of a thin graphene layer coated on the inner wall of the channel using an in situ microfluidic casting method. The helical shape allows the sensor to flexibly respond to both tensile and compressive strains in a wide dynamic detection range from 24 compressive strain to 20 tensile strain. Fabrication of the sensor involves embedding a helical thin metal wire with a plastic wrap into a precursor solution of an elastomeric polymer, forming a helical microfluidic channel by removing the wire from cured elastomer, followed by microfluidic casting of a graphene thin layer directly inside the helical channel. The wide dynamic range, in conjunction with mechanical flexibility and stretchability of the sensor, will enable practical wearable strain sensor applications where large strains are often involved.
- 2 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 16 (15361225) , 2602-2605
Fully Conformal Square-Patch Frequency-Selective Surface Toward Wearable Electromagnetic Shielding
This letter reports on a fully conformal square-patch frequency-selective surface (FSS) consisting of liquid metal alloy embedded within a flexible silicone elastomer. The flexible and elastic nature of the FSS provides high conformity to doubly curved surfaces. The transmission properties of the FSS on both singly and doubly curved surfaces are studied. This FSS can facilitate electromagnetic interference reduction in the X-band frequency range when wrapped on cylindrical or spherical radomes over dipole-like antennas, thus surpassing many existing flexible FSS technologies that usually allow conformable contact only with singly curved surfaces.
- 2 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 16 (15361225) , 2602-2605
Fully Conformal Square-Patch Frequency-Selective Surface Toward Wearable Electromagnetic Shielding
This letter reports on a fully conformal square-patch frequency-selective surface (FSS) consisting of liquid metal alloy embedded within a flexible silicone elastomer. The flexible and elastic nature of the FSS provides high conformity to doubly curved surfaces. The transmission properties of the FSS on both singly and doubly curved surfaces are studied. This FSS can facilitate electromagnetic interference reduction in the X-band frequency range when wrapped on cylindrical or spherical radomes over dipole-like antennas, thus surpassing many existing flexible FSS technologies that usually allow conformable contact only with singly curved surfaces.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 456-458
Tubular graphene sensors formed within planar and helical microfluidic channels
We report a helical shaped graphene strain sensor formed using a simple in situ microfluidic casting method. Fabrication of the sensor involves embedding of a helical thin metal wire into a precursor solution of elastomeric polymer, formation of a helical channel by removing the embedded metal wire from cured elastomer, and in situ casting of a thin graphene coating on the inner surface of the helical channel by filling the channel with aqueous graphene dispersion. The helical shape of the graphene sensor enables a wide detection range for both compressive and tensile strains.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 456-458
Tubular graphene sensors formed within planar and helical microfluidic channels
We report a helical shaped graphene strain sensor formed using a simple in situ microfluidic casting method. Fabrication of the sensor involves embedding of a helical thin metal wire into a precursor solution of elastomeric polymer, formation of a helical channel by removing the embedded metal wire from cured elastomer, and in situ casting of a thin graphene coating on the inner surface of the helical channel by filling the channel with aqueous graphene dispersion. The helical shape of the graphene sensor enables a wide detection range for both compressive and tensile strains.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 402-405
Tracking of water movement dynamics inside plants using leaf surface humidity sensors
This paper reports on a simple method to track water transport inside the plant by using multiple graphene oxide (GO) based relative humidity sensors. The sensor was formed on an adhesive polyimide film by selectively coating a GO layer on top of gold interdigitated electrodes and subsequently peeling the whole device structure off from a pre-coated polydimethylsiloxane temporary layer. To allow easy installation of the sensor at the leaf of plant, a simple assembly fixture was designed. The present measurement method provides information on how water moves within the plant that is associated with water use efficiency, an important selection trait to evaluate crop quality. In addition, the device can be adhered to other target surfaces due to its flexible and adhesive features.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 402-405
Tracking of water movement dynamics inside plants using leaf surface humidity sensors
This paper reports on a simple method to track water transport inside the plant by using multiple graphene oxide (GO) based relative humidity sensors. The sensor was formed on an adhesive polyimide film by selectively coating a GO layer on top of gold interdigitated electrodes and subsequently peeling the whole device structure off from a pre-coated polydimethylsiloxane temporary layer. To allow easy installation of the sensor at the leaf of plant, a simple assembly fixture was designed. The present measurement method provides information on how water moves within the plant that is associated with water use efficiency, an important selection trait to evaluate crop quality. In addition, the device can be adhered to other target surfaces due to its flexible and adhesive features.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Patterning of nanophotonic structures at optical fiber tip for refractive index sensing
This paper reports on an efficient and convenient method of patterning nanostructures on the cleaved facet of an optical fiber. The fabrication method utilizes ultraviolet (UV) assisted nanoimprint lithography in which the fiber tip is pressed against a stamp carrying nanoscale patterns, and then is exposed to UV radiation. The novelty of this work lies in utilizing simpler fabrication steps with better control over angle of contact at the fiber tip, which leads to rapid formation of nanostructures with well-defined features. An array of nanoposts are patterned at fiber tip and coated with titanium oxide to work as a guided mode resonant (GMR) device. The sensitivity of the fiber-tip GMR device to surrounding refractive index is 183.3 nm per refractive index unit. The proposed nanofabrication method offers a promising approach to develop remote fiber-optic sensors with intrinsic optical beam alignment for detecting the presence of subtle concentration of analytes at the fiber tip.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Patterning of nanophotonic structures at optical fiber tip for refractive index sensing
This paper reports on an efficient and convenient method of patterning nanostructures on the cleaved facet of an optical fiber. The fabrication method utilizes ultraviolet (UV) assisted nanoimprint lithography in which the fiber tip is pressed against a stamp carrying nanoscale patterns, and then is exposed to UV radiation. The novelty of this work lies in utilizing simpler fabrication steps with better control over angle of contact at the fiber tip, which leads to rapid formation of nanostructures with well-defined features. An array of nanoposts are patterned at fiber tip and coated with titanium oxide to work as a guided mode resonant (GMR) device. The sensitivity of the fiber-tip GMR device to surrounding refractive index is 183.3 nm per refractive index unit. The proposed nanofabrication method offers a promising approach to develop remote fiber-optic sensors with intrinsic optical beam alignment for detecting the presence of subtle concentration of analytes at the fiber tip.
- 11 July 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (71) , 67184-67195
Tunable bioelectrodes with wrinkled-ridged graphene oxide surfaces for electrochemical nitrate sensors
The paper reports on controlled formation of microscale wrinkles and ridges on the surface of a bioelectrode via mechanical stretching to tune and optimize the electrochemical sensing performances of graphene oxide (GO) based nitrate ion sensors. The bioelectrode consists of GO nanosheets drop-coated on a gold (Au) layer with a pre-stretched elastomer substrate. Enzyme nitrate reductase is used for covalent immobilization on the wrinkled-ridged GO surface. Upon relaxation from the pre-stretch, wrinkles or ridges are formed in the GO layer. As the pre-stretch increases, the sinusoidal wrinkles transform to localized ridges on the surface of bioelectrodes. Such morphological transitions, realized by simple mechanical stretching and relaxing, allow optimizing of the electrochemical current and sensing characteristics of the nitrate sensor. The sensing performances of the bioelectrodes at different pre-stretches are investigated. In addition to an increased electroactive surface area, the predominant localized ridges with small sinusoidal wrinkles formed on the GO surface provide a favorable spatial feature, enabling efficient radial diffusion of nitrate ions from surrounding analyte solutions onto the surface of the textured bioelectrode. At the pre-stretch of 8%, the nitrate sensor using the wrinkled-ridged bioelectrode exhibits a considerably high sensitivity of 0.224 μA L mol−1 cm−2 in response to nitrate ions, which is five times higher than that provided by the planar counterpart. Also, the textured bioelectrode shows high selectivity even in the presence of other inferring ions. The present nitrate sensor has potential applications in nitrate detection in sustainable agriculture, environmental monitoring, food analysis, and pharmaceutical industries.
- 11 July 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (71) , 67184-67195
Tunable bioelectrodes with wrinkled-ridged graphene oxide surfaces for electrochemical nitrate sensors
The paper reports on controlled formation of microscale wrinkles and ridges on the surface of a bioelectrode via mechanical stretching to tune and optimize the electrochemical sensing performances of graphene oxide (GO) based nitrate ion sensors. The bioelectrode consists of GO nanosheets drop-coated on a gold (Au) layer with a pre-stretched elastomer substrate. Enzyme nitrate reductase is used for covalent immobilization on the wrinkled-ridged GO surface. Upon relaxation from the pre-stretch, wrinkles or ridges are formed in the GO layer. As the pre-stretch increases, the sinusoidal wrinkles transform to localized ridges on the surface of bioelectrodes. Such morphological transitions, realized by simple mechanical stretching and relaxing, allow optimizing of the electrochemical current and sensing characteristics of the nitrate sensor. The sensing performances of the bioelectrodes at different pre-stretches are investigated. In addition to an increased electroactive surface area, the predominant localized ridges with small sinusoidal wrinkles formed on the GO surface provide a favorable spatial feature, enabling efficient radial diffusion of nitrate ions from surrounding analyte solutions onto the surface of the textured bioelectrode. At the pre-stretch of 8%, the nitrate sensor using the wrinkled-ridged bioelectrode exhibits a considerably high sensitivity of 0.224 μA L mol−1 cm−2 in response to nitrate ions, which is five times higher than that provided by the planar counterpart. Also, the textured bioelectrode shows high selectivity even in the presence of other inferring ions. The present nitrate sensor has potential applications in nitrate detection in sustainable agriculture, environmental monitoring, food analysis, and pharmaceutical industries.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 913-916
Plasmonic crystal gas sensor incorporating graphene oxide for detection of volatile organic compounds
This paper reports a gas sensor consisting of a thin layer of graphene oxide (GO) assembled on the top surface of mushroom plasmonic nanostructures. The plasmonic crystal structure is formed by an array of polymeric nanoposts with gold disks at the top and perforated nanoholes in a gold film at the bottom. The optical response of the plasmonic nanostructure is altered due to absorbing different concentrations of gas in presence of GO coating. The refractive index change of the GO layer with different thicknesses allows for selective detection of different gas species with the help of the principal component analysis-based pattern recognition algorithm. The present plasmonic nanostructure offers a promising approach to detect various volatile organic compounds.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 913-916
Plasmonic crystal gas sensor incorporating graphene oxide for detection of volatile organic compounds
This paper reports a gas sensor consisting of a thin layer of graphene oxide (GO) assembled on the top surface of mushroom plasmonic nanostructures. The plasmonic crystal structure is formed by an array of polymeric nanoposts with gold disks at the top and perforated nanoholes in a gold film at the bottom. The optical response of the plasmonic nanostructure is altered due to absorbing different concentrations of gas in presence of GO coating. The refractive index change of the GO layer with different thicknesses allows for selective detection of different gas species with the help of the principal component analysis-based pattern recognition algorithm. The present plasmonic nanostructure offers a promising approach to detect various volatile organic compounds.
- Open Access
- 18 December 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 18567
Tunable Optical Nanoantennas Incorporating Bowtie Nanoantenna Arrays with Stimuli-Responsive Polymer
We report on a temperature-responsive tunable plasmonic device that incorporates coupled bowtie nanoantenna arrays (BNAs) with a submicron-thick, thermosensitive hydrogel coating. The coupled plasmonic nanoparticles provide an intrinsically higher field enhancement than conventional individual nanoparticles. The favorable scaling of plasmonic dimers at the nanometer scale and ionic diffusion at the submicron scale is leveraged to achieve strong optical resonance and rapid hydrogel response, respectively. We demonstrate that the hydrogel-coated BNAs are able to sense environmental temperature variations. The phase transition of hydrogel leads to 16.2 nm of resonant wavelength shift for the hydrogel-coated BNAs, whereas only 3 nm for the uncoated counterpart. The response time of the device to temperature variations is only 250 ms, due to the small hydrogel thickness at the submicron scale. The demonstration of the ability of the device to tune its optical resonance in response to an environmental stimulus (here, temperature) suggests a possibility of making many other tunable plasmonic devices through the incorporation of coupled plasmonic nanostructures and various environmental-responsive hydrogels.
- 18 December 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 18567
Open AccessTunable Optical Nanoantennas Incorporating Bowtie Nanoantenna Arrays with Stimuli-Responsive Polymer
We report on a temperature-responsive tunable plasmonic device that incorporates coupled bowtie nanoantenna arrays (BNAs) with a submicron-thick, thermosensitive hydrogel coating. The coupled plasmonic nanoparticles provide an intrinsically higher field enhancement than conventional individual nanoparticles. The favorable scaling of plasmonic dimers at the nanometer scale and ionic diffusion at the submicron scale is leveraged to achieve strong optical resonance and rapid hydrogel response, respectively. We demonstrate that the hydrogel-coated BNAs are able to sense environmental temperature variations. The phase transition of hydrogel leads to 16.2 nm of resonant wavelength shift for the hydrogel-coated BNAs, whereas only 3 nm for the uncoated counterpart. The response time of the device to temperature variations is only 250 ms, due to the small hydrogel thickness at the submicron scale. The demonstration of the ability of the device to tune its optical resonance in response to an environmental stimulus (here, temperature) suggests a possibility of making many other tunable plasmonic devices through the incorporation of coupled plasmonic nanostructures and various environmental-responsive hydrogels.