Yantao Duan

To enhance the purification of exhaust gas, a g-C₃N₄/CeO₂/Bi₂O₃ dual type-II heterojunction photocatalysis was designed and prepared to suppress the recombination of electron–hole pairs and improve light energy utilization. The dual type-II heterojunction structure effectively reduced the bandgap (Eg) from 2.5 eV to 2.04 eV, thereby extending the light absorption of photocatalysis into the visible region. Following the design of the heterojunction, a self-cleaning process was developed and applied to asphalt pavement rut plates to evaluate its efficiency in degrading vehicle exhaust under real-road conditions. The coating was systematically characterized in terms of exhaust degradation efficiency, hardness, adhesion, water resistance, freeze–thaw durability, and skid resistance. Under 60 min of natural light irradiation, the purification efficiencies for HC, CO, CO₂, and NO_x reached 22.60%, 19.27%, 14.83%, and 50.01%, respectively. After three-repetition tests, the efficiencies remained high at 21.75%, 19.04%, 14.66%, and 49.83%, demonstrating excellent photocatalytic stability. All other road-performance indicators met the relevant China national standards. The application of this self-cleaning coating in road infrastructure presents a viable strategy for environmental remediation in transportation systems.

Electronic equipment brings great convenience to daily life but also causes a lot of electromagnetic radiation pollution. Therefore, there is an urgent demand for electromagnetic wave-absorbing materials with a low thickness, wide bandwidth, and strong absorption. This work obtained a high-performance electromagnetic wave absorption system by adding conductive carbon spheres (CSs) to the CH₃NH₃PbI₃ (MAPbI₃) absorber. In this system, MAPbI₃, with strong dipole and relaxation polarization, acts dominant to the wave absorber. The carbon spheres provide a free electron transport channel between MAPbI₃ lattices and constructs interfacial polarization loss in MAPbI₃/CS. By regulating the content of CSs, we speculate that this increased effective absorption bandwidth and reflection loss intensity are attributed to the conductive channel of the carbon sphere and the interfacial polarization. As a result, when the mass ratio of the carbon sphere is 7.7%, the reflection loss intensity of MAPbI₃/CS reaches −54 dB at 12 GHz, the corresponding effective absorption bandwidth is 4 GHz (10.24–14.24 GHz), and the absorber thickness is 2.96 mm. This work proves that enhancing conduction loss and interfacial polarization loss is an effective strategy for regulating the properties of dielectric loss-type absorbing materials. It also indicates that organic-inorganic hybrid perovskites have great potential in the field of electromagnetic wave absorption.

D-dot sensors can realize the non-contact measurement of transient electric fields, which is widely applied to electromagnetic pulse (EMP) measurements with characteristics of the wide frequency band, high linearity, and good stability. In order to achieve accurate calibration of D-dot sensors in the laboratory environment, this paper proposed a new calibration method based on system identification. Firstly, the D-dot sensor can be considered as a linear time-invariant (LTI) system under corner frequency, thus its frequency response can be characterized by the transfer function of a discrete output error (OE) model. Secondly, based on the partial linear regression of the transfer function curve, the sensitivity coefficient of the D-dot sensor is obtained. By increasing the influence weight of low-frequency components, this proposed method has better calibration performance when the waveform is distorted in the time domain, and can artificially adapt to the operating frequency range of the sensor at the same time.

In order to study the lighting indirect effects on the metal cylinder, the direct current injection test devices on the metal cylinder was studied in this paper based on experiment and simulation. The return conductor configuration was designed. A Giant Magneto Resistive (GMR) sensor was calibrated to measure the intensity of the magnetic field inside and outside the metal cylinder. The impulse current injection test system similar to coaxial transmission line was established and the injection experiment was carried out. In order to verify the experimental results, a numerical simulation using the CST Microwave Studio was given. The magnetic field intensity inside and outside the metal cylinder are discussed by comparing the experiment and computational results. Moreover, the space distribution of the magnetic field is also simulated. The results show the feasibility of the test devices. The conclusions provide foundation for further lightning indirect effect test on cylindrical ordnance.

The breakdown current, current impulse velocity, and E-field in air gap discharge are of interest among researchers on high-voltage engineering and lightning study. It is the breakdown current and current impulse velocity that govern the radiated E-field property. The current impulse velocity, however, is not well addressed in the literature. In this paper, we use a self-developed high-speed observation system, a Rogowski coil, and a transient E-field sensor to measure the current impulse propagation velocity, breakdown current, and vertical E-field in the rod-to-plane discharge after the air gap breakdown under dc voltage. From the time difference of arrival of light signals in different receiving channels, the resultant current impulse propagation velocity is measured as 6.81 ± 0.57 × 106 m/s. Meanwhile, the breakdown current at the bottom of the grounded rod electrode has a peak value of approximately 1.3 kA and 10%–90% rise time of 40 ns, and the transient vertical E-field at ground level has an amplitude of approximately 15 kV/m and 10%–90% rise time of 64 ns. In addition, according to the measured breakdown current and resultant current impulse velocity, the vertical E-field is computed by using the finite-difference time-domain method in the two-dimensional cylindrical coordinate system. The computed vertical E-field agrees well with the measured E-field, validating our measured current impulse velocity. Besides, the computed horizontal E-field and azimuthal H-field are also analyzed. Finally, the influence of current impulse velocity on the vertical and horizontal E-field and azimuthal H-field is discussed.

An improved alternating‐direction‐implicit (ADI) algorithm for an efficient Laguerre‐based body‐of‐revolution finite‐difference time‐domain (BOR–FDTD) method is presented. A new correction equation for Eρ * q is added to the linear equations to speed up the convergence, and the two‐step Gauss–Seidel procedure instead of the one‐step procedure in the existing algorithm is introduced in the entire iterative algorithm. To validate the accuracy and efficiency of the proposed algorithm, which is applied to the BOR structure, two scattering examples are provided to demonstrate the algorithm. At the same time, the relative reflection error of the perfectly matched layer (PML) is calculated for comparisons with Mur's absorbing boundary condition.

For high efficient analysis of an obliquely incident plane wave on periodic structures, one-step leapfrog locally one-dimensional finite-difference time-domain (LOD-FDTD) method is proposed in this letter. Firstly, by applying the LOD scheme into the improved split-field algorithm, unconditional stability can be achieved. And then, by introducing three auxiliary variables, the one-step leapfrog implementation for the LOD scheme is derived. Finally, the implementation of the convolutional perfectly matched layer (CPML) for the proposed method is derived. At last, numerical results are given to verify the accuracy and efficiency of the proposed method.