Juan Miguel Massone
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Juan Miguel Massone has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Roberto Enrique Boeri
Metallurgy Division, INTEMA CONICET-UNMdP, Mar del Plata, Argentina
11 shared publications - Marcos G. López
INTEMA, UNMdP – CONICET, Mar del Plata, Argentina
6 shared publications - Nicolás Emanuel Tenaglia
Department of Metallurgy, INTEMA – CONICET, University of Mar del Plata, Mar del Plata, Argentina
6 shared publications Alejandro Daniel Basso
Metallurgy Division, INTEMA – CONICET, University of Mar del Plata, Mar del Plata, Argentina
2 shared publicationsRoberto E. Boeri
INTEMA, UNMdP – CONICET, Mar del Plata, Argentina
2 shared publicationsAlejandro Basso
Univ Mar del Plata, Dept Met, INTEMA CONICET, Mar Del Plata, Argentina
1 shared publication
Latest Publications
- 17 March 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (1) , 271-281
Columnar-to-Equiaxed Transition in Cast Irons: An Experimental and Numerical Analysis
- 17 March 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (1) , 271-281
Columnar-to-Equiaxed Transition in Cast Irons: An Experimental and Numerical Analysis
- 21 November 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (3) , 1084-1090
Influence of Microshrinkage Cavities on the Plastic Deformation and Fracture Under Tensile Loading in Ferritic Ductile Iron
- 21 November 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (3) , 1084-1090
Influence of Microshrinkage Cavities on the Plastic Deformation and Fracture Under Tensile Loading in Ferritic Ductile Iron
- 1 November 2020
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 33 (6) , 258-265
Development of ultra-high strength carbide-free bainitic cast steels
High-silicon cast steels and proper heat treatment cycles were designed in order to obtain carbide-free bainitic microstructures. The design process allowed to obtain the desired microstructures after heat treatment cycles compatible with industrial practices and using low amounts of inexpensive alloying elements. The different chemical compositions and austempering temperatures tested resulted in ultra-high-strength steels showing remarkably total elongations. The obtained tensile properties satisfy the minimum requirements specified for AHSS in ASTM A1088 standard, and also the requirements for high-strength cast steels stated in ASTM A148. Moreover, many microstructures developed in this work reach the tensile performance of the very expensive maraging steels.
- 1 November 2020
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 33 (6) , 258-265
Development of ultra-high strength carbide-free bainitic cast steels
High-silicon cast steels and proper heat treatment cycles were designed in order to obtain carbide-free bainitic microstructures. The design process allowed to obtain the desired microstructures after heat treatment cycles compatible with industrial practices and using low amounts of inexpensive alloying elements. The different chemical compositions and austempering temperatures tested resulted in ultra-high-strength steels showing remarkably total elongations. The obtained tensile properties satisfy the minimum requirements specified for AHSS in ASTM A1088 standard, and also the requirements for high-strength cast steels stated in ASTM A148. Moreover, many microstructures developed in this work reach the tensile performance of the very expensive maraging steels.
- 3 October 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (3) , 906-915
Influence of the Austempering Time on the Mechanical Properties of Carbide-Free Bainitic Cast Steels
- 3 October 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (3) , 906-915
Influence of the Austempering Time on the Mechanical Properties of Carbide-Free Bainitic Cast Steels
- 2 April 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 14 (4) , 1172-1182
Solidification, Macrostructure and Shrinkage Formation of Ductile and Compacted Irons
- 2 April 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 14 (4) , 1172-1182
Solidification, Macrostructure and Shrinkage Formation of Ductile and Compacted Irons
- 2 March 2020
- Published by SAGE Publications in Materials Science and Technology
- Vol. 36 (6) , 690-698
Effect of microsegregation on carbide-free bainitic transformation in a high-silicon cast steel
A high silicon cast steel was studied in the as-cast condition in order to characterise its solidification macrostructure and microsegregation. The steel, poured into 32 mm-keel-block-shaped moulds, has a coarse solidification structure and marked microsegregation, containing low-alloyed areas with a total alloy content (Cr + Mn + Si) of 2.3 wt-% and high-alloyed zones of 5.3 wt-%. The bainitic transformation behaviour at 300°C was studied at different austempering times. The bainitic reaction occurs at different rates within the specimen volume, because of its chemical heterogeneity. An austempering heat treatment leads to an inhomogeneous carbide-free bainitic microstructure with different phase amounts, morphologies and sizes. The heterogeneous distribution of sizes and chemical compositions of retained austenite is speculated to benefit mechanical properties.
- 2 March 2020
- Published by SAGE Publications in Materials Science and Technology
- Vol. 36 (6) , 690-698
Effect of microsegregation on carbide-free bainitic transformation in a high-silicon cast steel
A high silicon cast steel was studied in the as-cast condition in order to characterise its solidification macrostructure and microsegregation. The steel, poured into 32 mm-keel-block-shaped moulds, has a coarse solidification structure and marked microsegregation, containing low-alloyed areas with a total alloy content (Cr + Mn + Si) of 2.3 wt-% and high-alloyed zones of 5.3 wt-%. The bainitic transformation behaviour at 300°C was studied at different austempering times. The bainitic reaction occurs at different rates within the specimen volume, because of its chemical heterogeneity. An austempering heat treatment leads to an inhomogeneous carbide-free bainitic microstructure with different phase amounts, morphologies and sizes. The heterogeneous distribution of sizes and chemical compositions of retained austenite is speculated to benefit mechanical properties.
- 4 December 2019
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 14 (3) , 689-695
Examination of the Size and Morphology of Austenite Grains in Lamellar Graphite Cast Iron
- 4 December 2019
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 14 (3) , 689-695
Examination of the Size and Morphology of Austenite Grains in Lamellar Graphite Cast Iron
- 14 August 2018
- Published by SAGE Publications in Materials Science and Technology
- Vol. 34 (16) , 1990-2000
Assessment of the austemperability of high-silicon cast steels through Jominy hardenability tests
The austemperability of seven high silicon cast steels with different alloy contents was characteri sed. The maximum round bar diameter that can be fully austempered changed from about 10 mm for an unalloyed steel to more than 70 mm for a low-alloy steel. The austemperability was calculated by applying a procedure based on a standard Jominy test and the characterisation of the microstructure along the Jominy sample. The method, which was validated experimentally, creates a relatively simple procedure to measure austemperability. Processing factors such as the ability of the salt bath to extract heat and the austempering temperature are accounted for the method. The metallographic study revealed the influence of microsegregation on hardenability, which is particularly important for cast steels.
- 14 August 2018
- Published by SAGE Publications in Materials Science and Technology
- Vol. 34 (16) , 1990-2000
Assessment of the austemperability of high-silicon cast steels through Jominy hardenability tests
The austemperability of seven high silicon cast steels with different alloy contents was characteri sed. The maximum round bar diameter that can be fully austempered changed from about 10 mm for an unalloyed steel to more than 70 mm for a low-alloy steel. The austemperability was calculated by applying a procedure based on a standard Jominy test and the characterisation of the microstructure along the Jominy sample. The method, which was validated experimentally, creates a relatively simple procedure to measure austemperability. Processing factors such as the ability of the salt bath to extract heat and the austempering temperature are accounted for the method. The metallographic study revealed the influence of microsegregation on hardenability, which is particularly important for cast steels.
- 31 July 2018
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 32 (1) , 21-30
Study of austempering kinetics of high silicon bainitic cast steels
This study investigates the effect of chemical composition and microsegregation on the bainitic transformation of high Si cast steels at two different austempering temperatures. The advance of the bainite precipitation as a function of time and temperature was monitored through measurements of the amount of retained austenite by X-ray diffraction, the evolution of hardness and microstructural characterization. The results showed that the bainitic transformation starts preferentially at zones with lower contents of alloying elements but later covers the entire matrix. The austempering heat treatments resulted in an apparently homogeneous bainitic microstructure throughout the entire matrix after a short period of time. The results encourage the continuation of the development of high Si steels suitable to produce carbide-free austempered cast parts.
- 31 July 2018
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 32 (1) , 21-30
Study of austempering kinetics of high silicon bainitic cast steels
This study investigates the effect of chemical composition and microsegregation on the bainitic transformation of high Si cast steels at two different austempering temperatures. The advance of the bainite precipitation as a function of time and temperature was monitored through measurements of the amount of retained austenite by X-ray diffraction, the evolution of hardness and microstructural characterization. The results showed that the bainitic transformation starts preferentially at zones with lower contents of alloying elements but later covers the entire matrix. The austempering heat treatments resulted in an apparently homogeneous bainitic microstructure throughout the entire matrix after a short period of time. The results encourage the continuation of the development of high Si steels suitable to produce carbide-free austempered cast parts.
- Open Access
- 1 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 925, 110-117
Evolution of the Macrostructure of Gray Cast Iron from Eutectic to Hypereutectic Composition
This work studies the evolution of the macrostructure of gray cast iron as the carbon equivalent (CE) increases from near-eutectic to highly hypereutectic values. The macrostructure of spherical samples of flake graphite irons of CE ranging between 4.24% and 5.23% was revealed by using direct austempering after solidification technique (DAAS). The results were analysed by applying the concept of coupled zone for gray cast irons. The coupled zone is a region in the stable Fe-C-Si diagram in which solidification proceeds as a cooperative growth of both austenite and flake graphite. The coupled zone for gray cast iron is claimed to be asymmetrical as the eutectic reaction is extended towards the prolongation of the austenite liquidus line. All the samples investigated in the present study show the presence of relatively large austenite grains, demonstrating that the number of active nucleation sites of austenite per unit volume is small. The observation of the microstructure shows the presence of several units of coupled growth inside each austenite grain, what proves that many eutectic colonies have grown from the same austenite nucleus, even for highly hypereutectic compositions. Colour etching was employed to reveal the “hidden” dendrites present in the microstructure. The results suggest that proeutectic graphite is not a good nucleating agent for austenite. These results contribute to the understanding of the solidification of hypereutectic gray irons and verify the earlier understanding of the solidification of eutectic gray irons and its extension to hypereutectic compositions.
- 1 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 925, 110-117
Open AccessEvolution of the Macrostructure of Gray Cast Iron from Eutectic to Hypereutectic Composition
This work studies the evolution of the macrostructure of gray cast iron as the carbon equivalent (CE) increases from near-eutectic to highly hypereutectic values. The macrostructure of spherical samples of flake graphite irons of CE ranging between 4.24% and 5.23% was revealed by using direct austempering after solidification technique (DAAS). The results were analysed by applying the concept of coupled zone for gray cast irons. The coupled zone is a region in the stable Fe-C-Si diagram in which solidification proceeds as a cooperative growth of both austenite and flake graphite. The coupled zone for gray cast iron is claimed to be asymmetrical as the eutectic reaction is extended towards the prolongation of the austenite liquidus line. All the samples investigated in the present study show the presence of relatively large austenite grains, demonstrating that the number of active nucleation sites of austenite per unit volume is small. The observation of the microstructure shows the presence of several units of coupled growth inside each austenite grain, what proves that many eutectic colonies have grown from the same austenite nucleus, even for highly hypereutectic compositions. Colour etching was employed to reveal the “hidden” dendrites present in the microstructure. The results suggest that proeutectic graphite is not a good nucleating agent for austenite. These results contribute to the understanding of the solidification of hypereutectic gray irons and verify the earlier understanding of the solidification of eutectic gray irons and its extension to hypereutectic compositions.