Pauli Lehto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pauli Lehto has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Heikki Remes
Aalto University
11 shared publications Jani Romanoff
Department of Mechanical Engineering, School of Engineering, Aalto University, Aalto, Finland
4 shared publicationsAri Niemelä
2 shared publications- Federica Mancini
Aalto University
2 shared publications Hannu Hänninen
2 shared publications- Jani Romanoff
Aalto University
2 shared publications
Latest Publications
- Open Access
- 20 August 2026
- Published by Springer Nature in Welding in the World
- Vol. 70 (12) , 6285-6302
Critical factors influencing fatigue behavior of high-strength dissimilar welded joints with thickness steps
This paper investigates the primary factors influencing the fatigue behavior of butt-welded joints connecting normal- and high-strength steels of varying thicknesses. The research focused on dissimilar joints composed of 20 mm S690QL and 15 mm AH36, with similar joints (20 mm S690QL and 15 mm S690QL) included for comparison. Comprehensive experimental measurements of fatigue strength, misalignment, local weld geometry, and local material hardness were carried out for both joint types featuring thickness steps. Fatigue tests and fracture surface analysis were conducted to identify failure locations for crack initiation. Fatigue strength assessments using the structural stress and effective notch stress approaches were carried out to evaluate the influence of geometry-dependent stress concentration on fatigue failure behavior. The experimental results indicate that the failure locations varied depending on the specimen type. For the dissimilar joints, the locations were identified at the weld toe, specifically at the boundary between the heat-affected zone and weld metal in S690 side, which exhibited lower microhardness values. A comparison of local stress ranges, accounting for the effects of misalignments and local weld geometries, showed higher stress ranges at the failure locations. The scatter of fatigue test results was reduced significantly when the local stress ranges were considered. Consequently, the study confirms that the interaction of local material properties and stress concentrations from global and local weld geometries influences the fatigue failure behavior of high-strength dissimilar welded joints with thickness steps.
- 20 August 2026
- Published by Springer Nature in Welding in the World
- Vol. 70 (12) , 6285-6302
Open AccessCritical factors influencing fatigue behavior of high-strength dissimilar welded joints with thickness steps
This paper investigates the primary factors influencing the fatigue behavior of butt-welded joints connecting normal- and high-strength steels of varying thicknesses. The research focused on dissimilar joints composed of 20 mm S690QL and 15 mm AH36, with similar joints (20 mm S690QL and 15 mm S690QL) included for comparison. Comprehensive experimental measurements of fatigue strength, misalignment, local weld geometry, and local material hardness were carried out for both joint types featuring thickness steps. Fatigue tests and fracture surface analysis were conducted to identify failure locations for crack initiation. Fatigue strength assessments using the structural stress and effective notch stress approaches were carried out to evaluate the influence of geometry-dependent stress concentration on fatigue failure behavior. The experimental results indicate that the failure locations varied depending on the specimen type. For the dissimilar joints, the locations were identified at the weld toe, specifically at the boundary between the heat-affected zone and weld metal in S690 side, which exhibited lower microhardness values. A comparison of local stress ranges, accounting for the effects of misalignments and local weld geometries, showed higher stress ranges at the failure locations. The scatter of fatigue test results was reduced significantly when the local stress ranges were considered. Consequently, the study confirms that the interaction of local material properties and stress concentrations from global and local weld geometries influences the fatigue failure behavior of high-strength dissimilar welded joints with thickness steps.
- Open Access
- 22 July 2026
- Published by Elsevier in Engineering Structures
- Vol. 366
Experimental and numerical full-scale investigation of a large triangular laminated insulating glass unit in bending under quasi-static loading
- 22 July 2026
- Published by Elsevier in Engineering Structures
- Vol. 366
Open AccessExperimental and numerical full-scale investigation of a large triangular laminated insulating glass unit in bending under quasi-static loading
- Open Access
- 5 March 2025
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 21 (10) , 1940-1950
Experimental validation of an analytical stress magnification factor for thin plates with welding-induced curvature
- 5 March 2025
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 21 (10) , 1940-1950
Open AccessExperimental validation of an analytical stress magnification factor for thin plates with welding-induced curvature
- Open Access
- 30 December 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Strength and Poisson’s ratio of fused filament fabrication parts made from carbon filler enhanced PEEK compounds at elevated temperatures
Engineering plastics are finding widespread applications across a broad temperature spectrum, with additive manufacturing (AM) having now become commonplace for producing aerospace-grade components from polymers. However, there is limited data available on the behavior of plastic AM parts exposed to elevated temperatures. This study focuses on investigating the tensile strength, tensile modulus and Poisson’s ratio of parts manufactured using fused filament fabrication (FFF) and polyetheretherketone (PEEK) plastics doped with two additives: short carbon fibers (SCFs) and multi-wall carbon nanotubes (MWCNTs). Tensile test specimens, conforming to the ISO 527 type-1b standard and printed in the XY-plane, were subjected to elevated temperatures (110 °C, 130 °C). After temperature stabilization, a tensile test was conducted to evaluate how elevated temperatures affect the mechanical properties of the parts. The results were compared to tensile test results obtained at room temperature. Additionally, computed micro-tomography was used to determine the porosity of the FFF parts. Furthermore, differential scanning calorimetry measurements were made. The results indicate that exposure to the elevated temperature range used in this work can reduce the tensile strength by 36%. The effects on the tensile modulus and Poisson’s ratio were less pronounced. Based on these findings, SCF-PEEK FFF parts demonstrate higher tensile modulus and specific strength compared to plain-PEEK at elevated temperatures (110–130 °C), supporting their use in lightweight aerospace structures.
- 30 December 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Open AccessStrength and Poisson’s ratio of fused filament fabrication parts made from carbon filler enhanced PEEK compounds at elevated temperatures
Engineering plastics are finding widespread applications across a broad temperature spectrum, with additive manufacturing (AM) having now become commonplace for producing aerospace-grade components from polymers. However, there is limited data available on the behavior of plastic AM parts exposed to elevated temperatures. This study focuses on investigating the tensile strength, tensile modulus and Poisson’s ratio of parts manufactured using fused filament fabrication (FFF) and polyetheretherketone (PEEK) plastics doped with two additives: short carbon fibers (SCFs) and multi-wall carbon nanotubes (MWCNTs). Tensile test specimens, conforming to the ISO 527 type-1b standard and printed in the XY-plane, were subjected to elevated temperatures (110 °C, 130 °C). After temperature stabilization, a tensile test was conducted to evaluate how elevated temperatures affect the mechanical properties of the parts. The results were compared to tensile test results obtained at room temperature. Additionally, computed micro-tomography was used to determine the porosity of the FFF parts. Furthermore, differential scanning calorimetry measurements were made. The results indicate that exposure to the elevated temperature range used in this work can reduce the tensile strength by 36%. The effects on the tensile modulus and Poisson’s ratio were less pronounced. Based on these findings, SCF-PEEK FFF parts demonstrate higher tensile modulus and specific strength compared to plain-PEEK at elevated temperatures (110–130 °C), supporting their use in lightweight aerospace structures.
- Open Access
- 17 May 2024
- Published by Elsevier in Materialia
- Vol. 36
Influence of sample extraction location on thermal desorption spectroscopy from a heat-resistant 13CrMo4-5 steel plate and correlation with microstructure features
- 17 May 2024
- Published by Elsevier in Materialia
- Vol. 36
Open AccessInfluence of sample extraction location on thermal desorption spectroscopy from a heat-resistant 13CrMo4-5 steel plate and correlation with microstructure features
- Open Access
- 10 August 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (11) , 4103-4118
Study of cyclic crack‐tip opening displacement of microstructurally small fatigue crack using digital image correlation
The current work investigates the relationship between the crack growth rate (CGR) and the cyclic crack‐tip opening displacement (ΔCTOD) of microstructurally small fatigue cracks by using high‐resolution digital image correlation (DIC). Load‐controlled fatigue tests were conducted on small‐scale specimens of 18%Cr body‐centered cubic ferritic stainless steel. Microstructurally small fatigue crack growth was analyzed based on accurate high sample‐rate measurements, starting from a sub‐grain crack length up to seven times the volume‐weighted grain size dv = 224 μm. Under these experimental conditions, the high‐resolution analyses reveal that variation from the otherwise linear relationship between CGR and ΔCTOD on double logarithmic scale is due to the crack‐tip bypassing an inhomogeneous shear strain localization zone. In this zone, ΔCTOD is not able to characterize the behavior of microstructurally small fatigue cracks. Outside the shear strain localization zone, ΔCTOD still is a valid crack driving force parameter.
- 10 August 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (11) , 4103-4118
Open AccessStudy of cyclic crack‐tip opening displacement of microstructurally small fatigue crack using digital image correlation
The current work investigates the relationship between the crack growth rate (CGR) and the cyclic crack‐tip opening displacement (ΔCTOD) of microstructurally small fatigue cracks by using high‐resolution digital image correlation (DIC). Load‐controlled fatigue tests were conducted on small‐scale specimens of 18%Cr body‐centered cubic ferritic stainless steel. Microstructurally small fatigue crack growth was analyzed based on accurate high sample‐rate measurements, starting from a sub‐grain crack length up to seven times the volume‐weighted grain size dv = 224 μm. Under these experimental conditions, the high‐resolution analyses reveal that variation from the otherwise linear relationship between CGR and ΔCTOD on double logarithmic scale is due to the crack‐tip bypassing an inhomogeneous shear strain localization zone. In this zone, ΔCTOD is not able to characterize the behavior of microstructurally small fatigue cracks. Outside the shear strain localization zone, ΔCTOD still is a valid crack driving force parameter.
- Open Access
- 14 April 2023
- Published by Elsevier in Additive Manufacturing
- Vol. 70
Fatigue damage process of additively manufactured 316 L steel using X-ray computed tomography imaging
- 14 April 2023
- Published by Elsevier in Additive Manufacturing
- Vol. 70
Open AccessFatigue damage process of additively manufactured 316 L steel using X-ray computed tomography imaging
- Open Access
- 4 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 363-377
EBSD characterisation of grain size distribution and grain sub-structures for ferritic steel weld metals
Microstructural characterisation of engineering materials is required for understanding the relationships between microstructure and mechanical properties. Conventionally grain size is measured from grain boundary maps obtained using optical or electron microscopy. This paper implements EBSD-based linear intercept measurement of spatial grain size variation for ferritic steel weld metals, making analysis flexible and robust. While grain size has been shown to correlate with the strength of the material according to the Hall–Petch relationship, similar grain sizes in weld metals with different phase volume fractions can have significantly different mechanical properties. Furthermore, the solidification of the weld pool induces the formation of grain sub-structures that can alter mechanical properties. The recently developed domain misorientation approach is used in this study to provide a more comprehensive characterisation of the grain sub-structures for ferritic steel weld metals. The studied weld metals consist of varying mixtures of primary ferrite, acicular ferrite, and bainite/martensite, with large differences observed in hardness, grain size, grain morphology, and dislocation cell size. For the studied weld metals, the average dislocation cell size varied between 0.68 and 1.41 µm, with bainitic/martensitic weld metals showing the smallest sub-structures and primary ferrite the largest. In contrast, the volume-weighted average grain size was largest for the bainitic/martensitic weld metal. Results indicate that a Hall–Petch-type relationship exists between hardness and average dislocation cell size and that it partially corrects the significantly different grain size—hardness relationship observed for ferritic and bainitic/martensitic weld metals. The methods and datasets are provided as open access.
- 4 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 363-377
Open AccessEBSD characterisation of grain size distribution and grain sub-structures for ferritic steel weld metals
Microstructural characterisation of engineering materials is required for understanding the relationships between microstructure and mechanical properties. Conventionally grain size is measured from grain boundary maps obtained using optical or electron microscopy. This paper implements EBSD-based linear intercept measurement of spatial grain size variation for ferritic steel weld metals, making analysis flexible and robust. While grain size has been shown to correlate with the strength of the material according to the Hall–Petch relationship, similar grain sizes in weld metals with different phase volume fractions can have significantly different mechanical properties. Furthermore, the solidification of the weld pool induces the formation of grain sub-structures that can alter mechanical properties. The recently developed domain misorientation approach is used in this study to provide a more comprehensive characterisation of the grain sub-structures for ferritic steel weld metals. The studied weld metals consist of varying mixtures of primary ferrite, acicular ferrite, and bainite/martensite, with large differences observed in hardness, grain size, grain morphology, and dislocation cell size. For the studied weld metals, the average dislocation cell size varied between 0.68 and 1.41 µm, with bainitic/martensitic weld metals showing the smallest sub-structures and primary ferrite the largest. In contrast, the volume-weighted average grain size was largest for the bainitic/martensitic weld metal. Results indicate that a Hall–Petch-type relationship exists between hardness and average dislocation cell size and that it partially corrects the significantly different grain size—hardness relationship observed for ferritic and bainitic/martensitic weld metals. The methods and datasets are provided as open access.
- Open Access
- 1 July 2021
EBSD datasets for low-alloy steel weld metals - Arc, Laser, and Laser-hybrid welding
- 1 July 2021
Open AccessEBSD datasets for low-alloy steel weld metals - Arc, Laser, and Laser-hybrid welding
- Open Access
- 1 March 2021
- Published by Elsevier in Ultramicroscopy
- Vol. 222, 113203
Adaptive domain misorientation approach for the EBSD measurement of deformation induced dislocation sub-structures
- 1 March 2021
- Published by Elsevier in Ultramicroscopy
- Vol. 222, 113203
Open AccessAdaptive domain misorientation approach for the EBSD measurement of deformation induced dislocation sub-structures