PCPatrick Carolan

Patrick Carolan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Patrick Carolan has a total of 135 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Towards 100 GHz Waveguide Ge/Si Avalanche Photodiodes for High-Speed Optical Interconnects

    by Amir Shahin, Conor Coughlan, Hakim Kobbi, Mathias Berciano, Didit Yudistira, Roger Loo, Shuchi Kaushik, Patrick Carolan, Marta Agati, Peter Verheyen, et al.

    We report on the design, modeling, and measurements of high-speed, silicon-contacted, waveguide-coupled Germanium-on-Silicon (Ge/Si) avalanche photodiodes (APDs) fabricated on 300 mm Silicon On insulator (SOI) wafers. The devices achieve a peak 3-dB bandwidth (BW) exceeding 100 GHz and maintain 70 GHz BW at a responsivity of 2 A/W in both the O- and C-bands, at a relatively low reverse bias of 7 V. These results demonstrate the strong potential of Ge/Si APDs to be used for next-generation short-reach optical interconnects targeting 400 Gbps per lane operation.

  • Open Access

    Structural transformation for BaBiO3-δ thin films grown on SrTiO3-buffered Si(001) induced by an in-situ molecular beam epitaxy cooldown process

    by Islam Ahmed, Olivier Richard, Partrick Carolan, Marco Gambin, Luca Ceccon, Moloud Kaviani, Stefan De Gendt, Clement Merckling

    Oxygen loss is a common defect type in perovskites which is caused by a low oxygen background pressure during growth. BaBiO3-δ thin films are grown by molecular beam epitaxy on SrTiO3-buffered Si(001) substrates. Although activated oxygen is supplied during growth, large amount of oxygen vacancies is created in the thin film depending on the cooldown process. Perovskite structure is obtained when the cooldown process includes an extended period during which activated oxygen is supplied. Another way for inducing the structural transformation is enabled via an ex-situ anneal at molecular oxygen. The transformation into BaBiO3 is manifested as reconstructed octahedra based on transmission electron microscopy, Raman spectroscopy, and photoluminescence. Additionally, smaller out-of-plane lattice constant is observed for the perovskite phase supported by X-ray diffraction. Thermal mismatch and multivalency-facilitated tensile strain exerted on the layers by the underlying Si substrates are presented as the driving force behind the creation of oxygen vacancies.


  • MoS2 synthesis by gas source MBE for transition metal dichalcogenides integration on large scale substrates

    by S. El Kazzi, W. Mortelmans, T. Nuytten, J. Meersschaut, P. Carolan, L. Landeloos, T. Conard, I. Radu, M. Heyns, C. Merckling

    We present in this paper the use of Gas Source Molecular Beam Epitaxy for the large-scale growth of transition metal dichalcogenides. Fiber-textured MoS2 co-deposited thin films (down to 1 MLs) are grown on commercially 200 mm wafer size templates where MX2 crystalline layers are achieved at temperatures ranging from RT to 550 °C. Raman Spectroscopy and photoluminescence measurements along with X-Ray Photoelectron Spectroscopy show that a low growth rate is essential for complete Mo sulfurization during MoS2 co-deposition. Finally, cross-section Transmission Electron Microscopy investigations are discussed to highlight the influence of SiO2 and Al2O3 used surfaces on MoS2 deposition.


  • Doping top-down e-beam fabricated germanium nanowires using molecular monolayers

    by B. Long, G. Alessio Verni, J. O’cOnnell, M. Shayesteh, A. Gangnaik, Y.M. Georgiev, P. Carolan, D. O’cOnnell, K.J. Kuhn, S.B. Clendenning, et al.


  • Structural and Electrical Investigation of MoS2Thin Films Formed by Thermal Assisted Conversion of Mo Metal

    by Ray Duffy, Patrick Foley, Bruno Filippone, Gioele Mirabelli, Dan O'COnnell, Brendan Sheehan, Pat Carolan, Michael Schmidt, Karim Cherkaoui, Riley Gatensby, et al.

    Large-area synthesis is of great demand for the preparation of high-performance transition-metal-dichalcogenides (TMD) devices, however there are only limited reports to date of device operation on large-area TMDs. In this work we fabricate MoS2 devices based on Thermal Assisted Conversion (TAC) of metal layers, and characterize the thin-films with material analysis combined with electrical device parameter extraction. Specifically we report on temperature dependent parameter extraction for Ti/Au contacts to MoS2 thin-films to determine sheet resistance (Rsh), resistivity (ρ), and the activation energy (EA) of on-state current flow. For undoped MoS2, ρ was determined to be 191 Ω.cm at 25°C. The activation energy of the on-state current was found to be 0.18 eV, pointing to the presence of deep levels in MoS2.


  • Open Access

    Bismuth Self-Limiting Growth of Ultrathin BiFeO3 Films

    by Nitin Deepak, Patrick Carolan, Lynette Keeney, Panfeng F. Zhang, Martyn E. Pemble, Roger W. Whatmore


  • Open Access

    Tunable nanoscale structural disorder in Aurivillius phase, n = 3 Bi4Ti3O12 thin films and their role in the transformation to n = 4, Bi5Ti3FeO15 phase

    by Nitin Deepak, Patrick Carolan, Lynette Keeney, Martyn E. Pemble, Roger W. Whatmore

    Naturally super-latticed Aurivillius phase ferroelectrics can accommodate various magnetic ions, opening up the possibility of making new room temperature multiferroics. Here, we studied the growth of single-phase Aurivillius phase Bi5Ti3FeO15 (BTFO) thin films, grown onto single crystalline SrTiO3 (STO) substrates, by doping Bi4Ti3O12 (BTO) with iron by liquid injection metal–organic chemical vapour deposition. The crystalline properties of the resulting films were characterized by X-ray diffraction and transmission electron microscopy. It has been found that the structural properties of the films depend strongly on the relative iron and titanium precursor injection volumes. Nanoscale structural disorder starts to occur in BTO films on the onset of iron precursor flow. A small iron precursor flow causes the formation of half-unit cells of BTFO inside BTO lattice, which in turns causes disorder in BTO films. This disorder can be tuned by varying iron content in the film. Atomic force microscopy shows how the growth mode switches from island growth to layer-by-layer growth mode as the composition changes from BTO to BTFO.


  • Influence of Substrate on Hafnium Silicate Metal-Insulator-Metal Capacitors Grown by Atomic Layer Deposition

    by B J Hutchinson, V S Teodorescu, R Negrea, B Sheehan, P Carolan, S O'BRien, M Modreanu, M E Pemble, I. M Povey

    In this paper we report on the structural and electrical properties of hafnium silicate films grown by atomic layer deposition on a platinum bottom electrode. The results are compared to previously published results from our laboratory for an aluminum bottom electrode structure, with otherwise identical processing of the dielectric layer. The results demonstrate that the bottom electrode has a marked effect on both the structure and electrical properties of the resulting MIM capacitor. The previously reported films on aluminum were found to exhibit excellent electrical properties over a range of substrate materials and were consistent with hafnium silicate. In this study high resolution transmission electron microscopy (HRTEM) analysis and Raman spectroscopy indicate that on platinum the main crystalline phase is monoclinic HfO2 with a dielectric constant (k) value of ~18. Despite the crystalline nature of the HfO2 no hysteresis was observed in the capacitance voltage measurements. The scanning transmission electron microscopy (STEM) analysis also reveals the presence of nanoparticles, located primarily towards the lower platinum metal electrode at the HfO2 grain boundaries. Based on energy-dispersive x-ray spectroscopy (EDX) analysis the nanoparticles are consistent with silicon oxide inclusions.

  • Electrical and physical characterization of the Al2O3/p-GaSb interface for 1%, 5%, 10%, and 22% (NH4)2S surface treatments

    by Uthayasankaran Peralagu, Ian M. Povey, Patrick Carolan, Jun Lin, Rocio Contreras-Guerrero, Ravi Droopad, Paul K. Hurley, Iain G. Thayne

    In this work, the impact of ammonium sulfide ((NH4)2S) surface treatment on the electrical passivation of the Al2O3/p-GaSb interface is studied for varying sulfide concentrations. Prior to atomic layer deposition of Al2O3, GaSb surfaces were treated in 1%, 5%, 10%, and 22% (NH4)2S solutions for 10 min at 295 K. The smallest stretch-out and flatband voltage shifts coupled with the largest capacitance swing, as indicated by capacitance-voltage (CV) measurements, were obtained for the 1% treatment. The resulting interface defect trap density (Dit) distribution showed a minimum value of 4 × 1012 cm−2eV−1 at Ev + 0.27 eV. Transmission electron microscopy and atomic force microscopy examination revealed the formation of interfacial layers and increased roughness at the Al2O3/p-GaSb interface of samples treated with 10% and 22% (NH4)2S. In combination, these effects degrade the interface quality as reflected in the CV characteristics.


  • Access resistance reduction in Ge nanowires and substrates based on non-destructive gas-source dopant in-diffusion

    by Ray Duffy, Maryam Shayesteh, Kevin Thomas, Emanuele Pelucchi, Ran Yu, Anushka Gangnaik, Yordan M. Georgiev, Patrick Carolan, Nikolay Petkov, Brenda Long, et al.

    To maintain semiconductor device scaling, in recent years industry has been forced to move from planar to non-planar device architectures. This alone has created the need to develop a radically new, non-destructive method for doping. Doping alters the electrical properties of a semiconductor, related to the access resistance. Low access resistance is necessary for high performance technology and reduced power consumption. In this work the authors reduced access resistance in top–down patterned Ge nanowires and Ge substrates by a non-destructive dopant in-diffusion process. Furthermore, an innovative electrical characterisation methodology is developed for nanowire and fin-based test structures to extract important parameters that are related to access resistance such as nanowire resistivity, sheet resistance, and active doping levels. Phosphine or arsine was flowed in a Metalorganic Vapour Phase Epitaxy reactor over heated Ge samples in the range of 650–700 °C. Dopants were incorporated and activated in this single step. No Ge growth accompanied this process. Active doping levels were determined by electrochemical capacitance–voltage free carrier profiling to be in the range of 1019 cm−3. The nanowires were patterned in an array of widths from 20–1000 nm. Cross-sectional Transmission Electron Microscopy of the doped nanowires showed minimal crystal damage. Electrical characterisation of the Ge nanowires was performed to contrast doping activation in thin-body structures with that in bulk substrates. Despite the high As dose incorporation on unpatterned samples, the nanowire analysis determined that the P-based process was the better choice for scaled features.