Romolo Remetti
Research Subjects
Romolo Remetti has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Luigi Lepore
ENEA, NUC-IRAD-CRGR, Nuclear Material Characterisation Laboratory and Radioactive Waste Management, ENEA Casaccia Research Centre, Via Anguillarese 301, 00123 Rome, Italy
9 shared publications Franco Vittorio Frazzoli
University of Rome “La Sapienza,” Dipartimento di Energetica Via Antonio Scarpa, 14-00161, Rome, Italy
3 shared publications- Giuseppe Augusto Marzo
Ames Research Center
3 shared publications U. Delprato
ELECOS SpA, 123 via degli Eroi di Cefalonia, I-00128 Rome, Italy
3 shared publicationsAlessandro Dodaro
ENEA Casaccia Research Center Via Anguillarese, 301-00060 S. Maria di Galeria, Rome, Italy
2 shared publications- Andrea Mascitti
Department of Engineering and Geology, “G. d’Annunzio” University of Chieti-Pescara, Viale Pindaro 42, 65127 Pescara, Italy
2 shared publications
Latest Publications
- Open Access
- 27 November 2022
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 14 (5) , 1525-1538
Effects of Oxidative Treatments on Biomethane Potential of Solid Olive Residues
As energy systems transition toward renewable resources, anaerobic digestion (AD) is actually receiving growing attention. AD relies on biochemical methane potential (BMP) tests to determine the methane potential of by-products of carbonious nature. This investigation aims to understand how an oxidative treatment, like the Fenton reaction, influences the BMP, starting from solid residues of olive oil production, coming from the two-phase extraction systems (TPES). We compared two different olive pomaces (with and without stones), both from TPES. The Fenton treatment here proposed is able to produce three effects in the employed matrices: improving the speed of BMP decreasing the bacteriostatic effect of phenols, reducing the H2S content in the produced biogas (precipitating it as FeS) and enhancing the production of methane in the first four weeks of the test. Graphical Abstract
- 27 November 2022
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 14 (5) , 1525-1538
Open AccessEffects of Oxidative Treatments on Biomethane Potential of Solid Olive Residues
As energy systems transition toward renewable resources, anaerobic digestion (AD) is actually receiving growing attention. AD relies on biochemical methane potential (BMP) tests to determine the methane potential of by-products of carbonious nature. This investigation aims to understand how an oxidative treatment, like the Fenton reaction, influences the BMP, starting from solid residues of olive oil production, coming from the two-phase extraction systems (TPES). We compared two different olive pomaces (with and without stones), both from TPES. The Fenton treatment here proposed is able to produce three effects in the employed matrices: improving the speed of BMP decreasing the bacteriostatic effect of phenols, reducing the H2S content in the produced biogas (precipitating it as FeS) and enhancing the production of methane in the first four weeks of the test. Graphical Abstract
- 23 November 2022
- Published by Elsevier in Physica Medica
- Vol. 104, 149-159
Perspectives in linear accelerator for FLASH VHEE: Study of a compact C-band system
- 23 November 2022
- Published by Elsevier in Physica Medica
- Vol. 104, 149-159
Perspectives in linear accelerator for FLASH VHEE: Study of a compact C-band system
- Open Access
- 25 July 2022
- Published by Springer Nature in Research Square
Effects of oxidative treatments on biomethane potential of solid olive residues
As energy systems transition toward renewable resources, anaerobic digestion (AD) is actually receiving growing attention. AD relies on biochemical methane potential (BMP) tests to determine the methane potential of by-products of carbonious nature. The aim of this investigation was to understand how an oxidative treatment, like the Fenton reaction, influences the BMP, starting from solid residues of olive oil production, coming from the two-phase extraction systems (TPES). We compared two different olive pomaces (with and without stones), both from TPES. The Fenton treatment here proposed is capable to produce three effects in the employed matrices: improving the speed of BMP decreasing the bacteriostatic effect of phenols, reducing the H2S content in the produced biogas (precipitating it as FeS) and enhancing the production of methane in the first four weeks of test.
- 25 July 2022
- Published by Springer Nature in Research Square
Open AccessEffects of oxidative treatments on biomethane potential of solid olive residues
As energy systems transition toward renewable resources, anaerobic digestion (AD) is actually receiving growing attention. AD relies on biochemical methane potential (BMP) tests to determine the methane potential of by-products of carbonious nature. The aim of this investigation was to understand how an oxidative treatment, like the Fenton reaction, influences the BMP, starting from solid residues of olive oil production, coming from the two-phase extraction systems (TPES). We compared two different olive pomaces (with and without stones), both from TPES. The Fenton treatment here proposed is capable to produce three effects in the employed matrices: improving the speed of BMP decreasing the bacteriostatic effect of phenols, reducing the H2S content in the produced biogas (precipitating it as FeS) and enhancing the production of methane in the first four weeks of test.
- Open Access
- 25 April 2022
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 19 (9) , 5229
ARMAX Forecast Model for Estimating the Annual radon Activity Concentration in Confined Environment by Short Measurements Performed by Active Detectors
This work aims to implement a forecast model that, combined with the use of active instrumentation for a rather limited time, and with the knowledge of a set of data referring to the environmental parameters of the place to be monitored, can estimate the concentration of indoor radon activity for longer time periods. This model has been built through the MATLAB program, exploiting the theories of time series and, in particular, ARMAX models, to reproduce the variation in the concentration of radon activity. The model validation has been carried out by comparing real vs. simulated values. In addition, analytic treatment of input data, such as temperature, pressure, and relative humidity, can reduce the influence of sudden transients allowing for better stability of the model. The final goal is to estimate the annual radon activity concentration on the basis of spot measurements carried out by active instrumentation, such to avoid the need to measure for an entire calendar year by the use of passive detectors. The first experimental results obtained in conjunction with active radon measurement demonstrates the applicability of the method not only for forecasting future average concentrations, but also for optimizing remedial actions.
- 25 April 2022
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 19 (9) , 5229
Open AccessARMAX Forecast Model for Estimating the Annual radon Activity Concentration in Confined Environment by Short Measurements Performed by Active Detectors
This work aims to implement a forecast model that, combined with the use of active instrumentation for a rather limited time, and with the knowledge of a set of data referring to the environmental parameters of the place to be monitored, can estimate the concentration of indoor radon activity for longer time periods. This model has been built through the MATLAB program, exploiting the theories of time series and, in particular, ARMAX models, to reproduce the variation in the concentration of radon activity. The model validation has been carried out by comparing real vs. simulated values. In addition, analytic treatment of input data, such as temperature, pressure, and relative humidity, can reduce the influence of sudden transients allowing for better stability of the model. The final goal is to estimate the annual radon activity concentration on the basis of spot measurements carried out by active instrumentation, such to avoid the need to measure for an entire calendar year by the use of passive detectors. The first experimental results obtained in conjunction with active radon measurement demonstrates the applicability of the method not only for forecasting future average concentrations, but also for optimizing remedial actions.
- Open Access
- 1 January 2020
- Published by Elsevier in Journal of Radiation Research and Applied Sciences
- Vol. 13 (1) , 747-757
Development of an electrostatic precipitator prototype to reduce exposure to radon progeny in poorly ventilated workplaces
Electrostatic precipitation is a well-known technology to reduce public exposure to radon daughters. A custom electrostatic precipitator (ESP) prototype has been designed and built to study the effectiveness of such a removal technique in specific workplaces having low-to-zero air exchange rates with external environments. An appropriate mathematical model has been set up in order to simulate the behavior of environmental and nuclear data throughout the ESP operation, to optimize the design for the prototype to be built, to estimate its effectiveness in terms of effective dose reduction. Reference detectors have been used to measure both the radon concentration and the potential alpha energy concentration of its decay products. After a full calibration procedure, two main experiments have been performed in a room satisfying the requirements of very low ventilation rate and high radon concentration. The effective dose rate after an ESP continuous working period of either 3 h or 5 h turned out to be 50% lower than the value measured before ESP switching ON. The main contribution to dose reduction was found to be given by the first 2 hours of operation.
- 1 January 2020
- Published by Elsevier in Journal of Radiation Research and Applied Sciences
- Vol. 13 (1) , 747-757
Open AccessDevelopment of an electrostatic precipitator prototype to reduce exposure to radon progeny in poorly ventilated workplaces
Electrostatic precipitation is a well-known technology to reduce public exposure to radon daughters. A custom electrostatic precipitator (ESP) prototype has been designed and built to study the effectiveness of such a removal technique in specific workplaces having low-to-zero air exchange rates with external environments. An appropriate mathematical model has been set up in order to simulate the behavior of environmental and nuclear data throughout the ESP operation, to optimize the design for the prototype to be built, to estimate its effectiveness in terms of effective dose reduction. Reference detectors have been used to measure both the radon concentration and the potential alpha energy concentration of its decay products. After a full calibration procedure, two main experiments have been performed in a room satisfying the requirements of very low ventilation rate and high radon concentration. The effective dose rate after an ESP continuous working period of either 3 h or 5 h turned out to be 50% lower than the value measured before ESP switching ON. The main contribution to dose reduction was found to be given by the first 2 hours of operation.
- 1 December 2017
- Published by Elsevier in Radiation Measurements
- Vol. 107, 111-114
Feasibility study on the application of solid state tracks detectors for fast surveys of residual alpha contamination in decommissioning activities
- 1 December 2017
- Published by Elsevier in Radiation Measurements
- Vol. 107, 111-114
Feasibility study on the application of solid state tracks detectors for fast surveys of residual alpha contamination in decommissioning activities
- 3 October 2017
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 314 (2) , 1287-1296
Experimental tests on the reduction of radon decay products’ unattached fraction in indoor environment and its influence on effective dose
- 3 October 2017
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 314 (2) , 1287-1296
Experimental tests on the reduction of radon decay products’ unattached fraction in indoor environment and its influence on effective dose
- 1 October 2017
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 322, 536-546
A proposal for an alternative use of prompt-Self Powered Neutron Detectors: Online spectral-deconvolution for monitoring high-intensity neutron flux in LFRs
- 1 October 2017
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 322, 536-546
A proposal for an alternative use of prompt-Self Powered Neutron Detectors: Online spectral-deconvolution for monitoring high-intensity neutron flux in LFRs
- 31 July 2017
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 3 (4)
Application of Prompt Self-Powered Neutron Detectors to the Lead-Cooled Fast Reactor Demonstrator ALFRED: Validation of the Monte Carlo Model for Selected SPNDs
The advanced lead fast reactor European demonstrator (ALFRED) is a European research initiative into the framework of the Generation IV International Forum facilities. ALFRED is a scaled down reactor compared to the industrial prototype European lead fast reactor proposed in lead-cooled European advanced demonstration reactor. It has a relatively low power (125 MWe) with a compact design to reduce the cost but maintaining its representativeness and it is cooled by pure lead. One of the open issues is linked to the neutron flux in-core monitoring system because of the harshness of the environment the detectors should be installed in, due to high temperatures, and the neutron-gamma radiation field levels. Monte Carlo simulation is a possible way of facing the problem, reproducing into a virtual world the reactor core, the surrounding environment and radiation interactions. In previous works, neutron spectra and gamma doses at possible detectors' locations in ALFRED were retrieved, with consideration on the applicability of each suitable device currently available. Fission chambers (FCs) were found to be exploited at reactor start-up and intermediate power range. Prompt self-powered neutron detectors (SPNDs) seemed to be the best solution to monitor the reactor full power, becoming the main research target: their effective applicability on field has to be demonstrated. SPND applications do not include reactor control purposes usually. Moreover, their irradiation experience involved thermal and epithermal neutron spectra monitoring, mainly. The lack of data when SPNDs sense fast neutron fluxes in terms of prompt-response pushed the authors to deepen the study in such direction. The work herein shows the mathematical approach based on Monte Carlo simulation of SPNDs by the Monte Carlo N-particle eXtended code (MCNPX), so as to study the capability of the code in reproducing real devices' signals while experimented on field. Such a verification turned out to be the preliminary stage for studying new concepts for SPNDs, in terms of sensitive materials and geometries, envisaging the possibility for designing, prototyping, and testing new devices in suitable fast neutron-flux facilities.
- 31 July 2017
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 3 (4)
Application of Prompt Self-Powered Neutron Detectors to the Lead-Cooled Fast Reactor Demonstrator ALFRED: Validation of the Monte Carlo Model for Selected SPNDs
The advanced lead fast reactor European demonstrator (ALFRED) is a European research initiative into the framework of the Generation IV International Forum facilities. ALFRED is a scaled down reactor compared to the industrial prototype European lead fast reactor proposed in lead-cooled European advanced demonstration reactor. It has a relatively low power (125 MWe) with a compact design to reduce the cost but maintaining its representativeness and it is cooled by pure lead. One of the open issues is linked to the neutron flux in-core monitoring system because of the harshness of the environment the detectors should be installed in, due to high temperatures, and the neutron-gamma radiation field levels. Monte Carlo simulation is a possible way of facing the problem, reproducing into a virtual world the reactor core, the surrounding environment and radiation interactions. In previous works, neutron spectra and gamma doses at possible detectors' locations in ALFRED were retrieved, with consideration on the applicability of each suitable device currently available. Fission chambers (FCs) were found to be exploited at reactor start-up and intermediate power range. Prompt self-powered neutron detectors (SPNDs) seemed to be the best solution to monitor the reactor full power, becoming the main research target: their effective applicability on field has to be demonstrated. SPND applications do not include reactor control purposes usually. Moreover, their irradiation experience involved thermal and epithermal neutron spectra monitoring, mainly. The lack of data when SPNDs sense fast neutron fluxes in terms of prompt-response pushed the authors to deepen the study in such direction. The work herein shows the mathematical approach based on Monte Carlo simulation of SPNDs by the Monte Carlo N-particle eXtended code (MCNPX), so as to study the capability of the code in reproducing real devices' signals while experimented on field. Such a verification turned out to be the preliminary stage for studying new concepts for SPNDs, in terms of sensitive materials and geometries, envisaging the possibility for designing, prototyping, and testing new devices in suitable fast neutron-flux facilities.
- Open Access
- 25 April 2017
- Published by WITPRESS LTD.
- Vol. 211, 197-206
CONSIDERATIONS ON REDUCTION OF INDOOR AIR POLLUTION FROM RADIOACTIVE EMISSIONS FROM BUILDING MATERIALS AND THE GROUND
The goal of this paper is to study the reduction of health risks from indoor radioactive pollutants, as thoron emissions from common building...
- 25 April 2017
- Published by WITPRESS LTD.
- Vol. 211, 197-206
Open AccessCONSIDERATIONS ON REDUCTION OF INDOOR AIR POLLUTION FROM RADIOACTIVE EMISSIONS FROM BUILDING MATERIALS AND THE GROUND
The goal of this paper is to study the reduction of health risks from indoor radioactive pollutants, as thoron emissions from common building...