Xin Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xin Deng has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Houston Wood
University of Virginia, Charlottesville, VA
5 shared publicationsRoger Fittro
University of Virginia, Charlottesville, VA
5 shared publicationsCori Watson
University of Virginia, Charlottesville, VA
4 shared publicationsBrian Weaver
University of Virginia, Charlottesville, VA
3 shared publications- Houston G. Wood
Professor Rotating Machinery and Controls (ROMAC) Laboratory, Department of Mechanical and Aerospace Engineering, University of Virginia, 122 Engineer's Way, Charlottesville, VA 22904-4746
2 shared publications Minhui He
University of Virginia, Charlottesville, VA
2 shared publications
Latest Publications
- 6 June 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (12)
Study of Temperature Drop Region in Transitional Region in Fluid-Film Thrust Bearings
A thrust bearing is a type of rotary bearing that permits rotation between parts and is designed to support a load parallel to the axis of rotation. There is a temperature drop region with the increase in speed. However, previous researchers mainly showed such temperature drop experimentally, and the physics causing such temperature drop is not understood. A full fluid–solid computational fluid dynamics (CFD) model was developed for a center pivot, tilting pad, and fluid-film thrust-bearing experimental model to study the physics of temperature drop in the transitional region. A novel physics of causing temperature drop in the transitional region was proposed, analyzed, and verified.
- 6 June 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (12)
Study of Temperature Drop Region in Transitional Region in Fluid-Film Thrust Bearings
A thrust bearing is a type of rotary bearing that permits rotation between parts and is designed to support a load parallel to the axis of rotation. There is a temperature drop region with the increase in speed. However, previous researchers mainly showed such temperature drop experimentally, and the physics causing such temperature drop is not understood. A full fluid–solid computational fluid dynamics (CFD) model was developed for a center pivot, tilting pad, and fluid-film thrust-bearing experimental model to study the physics of temperature drop in the transitional region. A novel physics of causing temperature drop in the transitional region was proposed, analyzed, and verified.
- 22 November 2023
- Published by ASME International in Journal of Tribology
- Vol. 146 (3) , 1-9
A Mixed Zero-Equation and One-Equation Turbulence Model in Fluid-Film Thrust Bearings
A thrust bearing is a rotary bearing that facilitates rotational movement between components and is specifically engineered to provide support for a load that is parallel to the axis of rotation. The generation of the inter-surface film pressure is attributed to the relative motion (rotation) of the surfaces, which results in the lubricant being drawn into the converging wedge formed between them. The interface between the unmovable and moving parts is demarcated by a slender layer of lubricating fluid, including but not limited to oil, water, air, or other process fluid. The conventional zero-equation model can be enhanced to achieve higher precision in forecasting and reduce dependence on empirical data, owing to its inherent limitations. A novel turbulence model that combines zero-equation and one-equation approaches has been developed and implemented in the recently introduced modeling tool package for thrust bearings. In the Prandtl one-equation turbulence model, the length scale is a necessary but undetermined term. A novel mixed model has been implemented utilizing the Prandtl one-equation along with a novel-length scale. The tool package is a Thermo-Hydrodynamic (THD) code that involves iterative computations between the Reynolds’ equation, turbulence equation, energy equation within the film, and conduction equation in pad and runner. The new model yields an eddy viscosity that exhibits a substantial level of proximity to both eddy viscosity transport (EVT) and direct numerical simulation (DNS), and exhibits significant enhancements in comparison to the traditional Ng–Pan zero-equation turbulence model.
- 22 November 2023
- Published by ASME International in Journal of Tribology
- Vol. 146 (3) , 1-9
A Mixed Zero-Equation and One-Equation Turbulence Model in Fluid-Film Thrust Bearings
A thrust bearing is a rotary bearing that facilitates rotational movement between components and is specifically engineered to provide support for a load that is parallel to the axis of rotation. The generation of the inter-surface film pressure is attributed to the relative motion (rotation) of the surfaces, which results in the lubricant being drawn into the converging wedge formed between them. The interface between the unmovable and moving parts is demarcated by a slender layer of lubricating fluid, including but not limited to oil, water, air, or other process fluid. The conventional zero-equation model can be enhanced to achieve higher precision in forecasting and reduce dependence on empirical data, owing to its inherent limitations. A novel turbulence model that combines zero-equation and one-equation approaches has been developed and implemented in the recently introduced modeling tool package for thrust bearings. In the Prandtl one-equation turbulence model, the length scale is a necessary but undetermined term. A novel mixed model has been implemented utilizing the Prandtl one-equation along with a novel-length scale. The tool package is a Thermo-Hydrodynamic (THD) code that involves iterative computations between the Reynolds’ equation, turbulence equation, energy equation within the film, and conduction equation in pad and runner. The new model yields an eddy viscosity that exhibits a substantial level of proximity to both eddy viscosity transport (EVT) and direct numerical simulation (DNS), and exhibits significant enhancements in comparison to the traditional Ng–Pan zero-equation turbulence model.
- 7 January 2019
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (7)
Methodology of Turbulence Parameter Correction in Water-Lubricated Thrust Bearings
Oil-lubricated bearings are widely used in high-speed rotating machines such as those found in automotive industries and aerospace. However, environmental issues and risk-averse operations are resulting in the removal of oil and the replacement of all sealed oil bearings with reliable water-lubricated bearings. The low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. This requires finer meshes for finite element modeling when compared to oil-lubricated bearings as the low-viscosity fluid produces a very thin lubricant film. Analyzing water-lubricated bearings can also produce convergence and accuracy issues in traditional oil-based analysis codes. Fitting the velocity profile with experiments having a nondimensional wall distance y+ in a certain range results in Ng-optimized Reichardt's constants k and δ+. The definition of y+ can be used to approximate the first layer thickness calculated for a uniform mesh. On the condition that the y+ is fixed to that of a standard oil bearing for which an oil-bearing code was validated, the number of elements across the film thickness and coefficients used in the eddy-viscosity equation can be adjusted to allow for convergence with other fluids other than that which the traditional oil-bearing code was designed for. This study proposed a new methodology to preserve the y+ value to make water-lubricated thrust bearing models valid. A method for determining the required number of cross-film elements in water-lubricated bearings was found. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 7 January 2019
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (7)
Methodology of Turbulence Parameter Correction in Water-Lubricated Thrust Bearings
Oil-lubricated bearings are widely used in high-speed rotating machines such as those found in automotive industries and aerospace. However, environmental issues and risk-averse operations are resulting in the removal of oil and the replacement of all sealed oil bearings with reliable water-lubricated bearings. The low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. This requires finer meshes for finite element modeling when compared to oil-lubricated bearings as the low-viscosity fluid produces a very thin lubricant film. Analyzing water-lubricated bearings can also produce convergence and accuracy issues in traditional oil-based analysis codes. Fitting the velocity profile with experiments having a nondimensional wall distance y+ in a certain range results in Ng-optimized Reichardt's constants k and δ+. The definition of y+ can be used to approximate the first layer thickness calculated for a uniform mesh. On the condition that the y+ is fixed to that of a standard oil bearing for which an oil-bearing code was validated, the number of elements across the film thickness and coefficients used in the eddy-viscosity equation can be adjusted to allow for convergence with other fluids other than that which the traditional oil-bearing code was designed for. This study proposed a new methodology to preserve the y+ value to make water-lubricated thrust bearing models valid. A method for determining the required number of cross-film elements in water-lubricated bearings was found. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 9 November 2018
- Published by ASME International
Comparison of Experimental, Thermoelastohydrodynamic (TEHD) and Thermal, Non-Deforming Computational Fluid Dynamics (CFD) Results for Thrust Bearings: Part II
A thrust bearing is a particular type of rotary bearing permitting rotation between parts but designed to support a predominately axial load. Part I of this study was submitted to ASME 5th Joint US-European Fluids Engineering Summer Meeting. It compared the experimental, TEHD and CFD results for a thrust bearing. Reasonable relative errors between these three results were observed. The outlet oil film thickness at low speeds and the inlet oil film thickness at high speeds as calculated using TEHD were found to be more accurate than their counterparts. Isothermal, non-deforming CFD was found to predict outlet film thickness accurately as thermal deformation has a lower impact in the outlet region. Isothermal and non-deforming CFD was also found to produce a qualitatively accurate film thickness and pressure distribution. Experimental data from a second paper reported by the same authors in Part I, provides temperature measurements in two different pads and showed some variation of temperature from pad to pad. A thermal CFD, different from isothermal CFD in Part I, was performed in this Part II. Different data analysis methods will be included in Part II including a comparison of leading edge, mid-plane and trailing edge temperature at two loads, two speeds. 24 different speed-load combination TEHD cases and 12 CFD cases were run in Part II in addition to the 32 TEHD cases and 8 CFD cases in Part I. Both TEHD and CFD underpredict the slope between temperature and shaft speeds. TEHD also underpredicts the slope between temperature and bearing loads while CFD can get an accurate slope between temperature and bearing loads. An improved inlet temperature model would fix the error between temperature and bearing load in CFD, and also can enable CFD to have the same accuracy as TEHD analysis for the temperature versus shaft speed relation. The inlet film thickness from both TEHD and CFD is underestimated. TEHD is more accurate than CFD in outlet film thickness, or minimum film thickness, which is a critical performance characteristic in fluid film thrust bearings. While CFD is more accurate than TEHD in inlet film thickness and power loss.
- 9 November 2018
- Published by ASME International
Comparison of Experimental, Thermoelastohydrodynamic (TEHD) and Thermal, Non-Deforming Computational Fluid Dynamics (CFD) Results for Thrust Bearings: Part II
A thrust bearing is a particular type of rotary bearing permitting rotation between parts but designed to support a predominately axial load. Part I of this study was submitted to ASME 5th Joint US-European Fluids Engineering Summer Meeting. It compared the experimental, TEHD and CFD results for a thrust bearing. Reasonable relative errors between these three results were observed. The outlet oil film thickness at low speeds and the inlet oil film thickness at high speeds as calculated using TEHD were found to be more accurate than their counterparts. Isothermal, non-deforming CFD was found to predict outlet film thickness accurately as thermal deformation has a lower impact in the outlet region. Isothermal and non-deforming CFD was also found to produce a qualitatively accurate film thickness and pressure distribution. Experimental data from a second paper reported by the same authors in Part I, provides temperature measurements in two different pads and showed some variation of temperature from pad to pad. A thermal CFD, different from isothermal CFD in Part I, was performed in this Part II. Different data analysis methods will be included in Part II including a comparison of leading edge, mid-plane and trailing edge temperature at two loads, two speeds. 24 different speed-load combination TEHD cases and 12 CFD cases were run in Part II in addition to the 32 TEHD cases and 8 CFD cases in Part I. Both TEHD and CFD underpredict the slope between temperature and shaft speeds. TEHD also underpredicts the slope between temperature and bearing loads while CFD can get an accurate slope between temperature and bearing loads. An improved inlet temperature model would fix the error between temperature and bearing load in CFD, and also can enable CFD to have the same accuracy as TEHD analysis for the temperature versus shaft speed relation. The inlet film thickness from both TEHD and CFD is underestimated. TEHD is more accurate than CFD in outlet film thickness, or minimum film thickness, which is a critical performance characteristic in fluid film thrust bearings. While CFD is more accurate than TEHD in inlet film thickness and power loss.
- 15 July 2018
- Published by ASME International
Comparison of Experimental, Thermoelastohydrodynamic (TEHD) and Isothermal, Non-Deforming Computational Fluid Dynamics (CFD) Results for Thrust Bearings
Bearings are machine elements that allow components to move with respect to each other. A thrust bearing is a particular type of rotary bearing permitting rotation between parts but designed to support a predominately axial load. Oil-lubricated bearings are widely used in high speed rotating machines such as those found in the aerospace and automotive industries. With the increase of velocity, the lubrication regime will go through boundary lubrication, mixed lubrication, and hydrodynamic lubrication (full film). In this paper, the analysis was in the hydrodynamic lubrication region. THRUST is used to predict the steady-state operating characteristics of oil-lubricated thrust bearings. As a thermoelastohydrodynamic prediction tool, THRUST assumes a 3D turbulence model, 3D energy equation, and 2D Reynolds equation. Turbulence is included by obtaining average values of eddy momentum flux (Reynolds stress) and averaging the influence down to a 2D Reynolds equation. Convergence is achieved by iterating on the pad tilt angles and pivot film thickness until the integrated pressure matches the load applied to the pad. Despite the multiple experimental, CFD, and TEHD studies of thrust bearings that have been performed to date, no validation has yet been performed to confirm the accuracy of TEHD methods in modeling the performance of thrust bearings by both experimental and advanced computational means simultaneously. This study addresses this need by comparing TEHD and CFD simulation results of film thickness, temperature, power loss, and pressure in thrust bearings taken from the literature at multiple speeds and loads with results from experimental data. Starting from the case of the lowest speed and load, it was verified that this case is indeed laminar and with negligible thermal and elastic effects. Four cases were run in THRUST, a TEHD solver, combining thermal and deformation in each rotational speed and load combination. Additionally, a CFD study was performed in ANSYS CFX with the assumptions of isothermal, non-deforming. The average viscosity from THRUST was used in CFD to follow the effects of the isoviscous assumption. Then, the experimental, TEHD and CFD results were compared at each case. Experimental, TEHD, and CFD results show acceptable agreement when turbulence is negligible.
- 15 July 2018
- Published by ASME International
Comparison of Experimental, Thermoelastohydrodynamic (TEHD) and Isothermal, Non-Deforming Computational Fluid Dynamics (CFD) Results for Thrust Bearings
Bearings are machine elements that allow components to move with respect to each other. A thrust bearing is a particular type of rotary bearing permitting rotation between parts but designed to support a predominately axial load. Oil-lubricated bearings are widely used in high speed rotating machines such as those found in the aerospace and automotive industries. With the increase of velocity, the lubrication regime will go through boundary lubrication, mixed lubrication, and hydrodynamic lubrication (full film). In this paper, the analysis was in the hydrodynamic lubrication region. THRUST is used to predict the steady-state operating characteristics of oil-lubricated thrust bearings. As a thermoelastohydrodynamic prediction tool, THRUST assumes a 3D turbulence model, 3D energy equation, and 2D Reynolds equation. Turbulence is included by obtaining average values of eddy momentum flux (Reynolds stress) and averaging the influence down to a 2D Reynolds equation. Convergence is achieved by iterating on the pad tilt angles and pivot film thickness until the integrated pressure matches the load applied to the pad. Despite the multiple experimental, CFD, and TEHD studies of thrust bearings that have been performed to date, no validation has yet been performed to confirm the accuracy of TEHD methods in modeling the performance of thrust bearings by both experimental and advanced computational means simultaneously. This study addresses this need by comparing TEHD and CFD simulation results of film thickness, temperature, power loss, and pressure in thrust bearings taken from the literature at multiple speeds and loads with results from experimental data. Starting from the case of the lowest speed and load, it was verified that this case is indeed laminar and with negligible thermal and elastic effects. Four cases were run in THRUST, a TEHD solver, combining thermal and deformation in each rotational speed and load combination. Additionally, a CFD study was performed in ANSYS CFX with the assumptions of isothermal, non-deforming. The average viscosity from THRUST was used in CFD to follow the effects of the isoviscous assumption. Then, the experimental, TEHD and CFD results were compared at each case. Experimental, TEHD, and CFD results show acceptable agreement when turbulence is negligible.
- 11 June 2018
- Published by ASME International
Turbulence Input Parameters Correction Methodology in Water Lubricated Thrust Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those found in the aerospace and automotive industries. However, environmental issues and risk-averse operations are resulting in the removal of oil and the replacement of all sealed oil bearings with reliable water-lubricated bearings. Due to the different fluid properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. This requires finer meshes when compared to oil-lubricated bearings as the low-viscosity fluid produces a very thin lubricant film. Analyzing water-lubricated bearings can also produce convergence and accuracy issues in traditional oil-based analysis codes. Thermal deformation largely affects oil-lubricated bearings, while having limited effects on water lubrication; mechanical deformation largely affects water lubrication, while its effects are typically lower than thermal deformation with oil. One common turbulence model used in these analysis tools is the eddy-viscosity model. Eddy-viscosity depends on the wall shear stress, therefore effective wall shear stress modeling is necessary in determining an appropriate turbulence model. Improving the accuracy and efficiency of modeling approaches for eddy-viscosity in turbulence models is of great importance. Therefore, the purpose of this study is to perform mesh refinement for water-lubricated bearings based on methodologies of eddy-viscosity modeling to improve their accuracy. According to Szeri [1], εm/v for the Boussinesq hypothesis is given by Reichardt’s formula. Fitting the velocity profile with experiments having a y+ in the range of 0–1,000 results in Ng-optimized Reichardt’s constants k = 0.4 and δ+ = 10.7. He clearly states that for y+ > 1000 theoretical predictions and experiments have a greater variance. Armentrout and others [2] developed an equation for δ+ as a function of the pivot Reynolds number, which they validated with CFD simulations. The definition of y+ can be used to approximate the first layer thickness calculated for a uniform mesh. Together with Armentrout’s equation, the number of required elements across the film thickness can be obtained. For typical turbulence models, the y+ must be within a certain range to be accurate. On the condition that the y+ is fixed to that of a standard oil bearing for which an oil bearing code was validated, the number of elements across the film thickness and coefficients used in the eddy-viscosity equation can be adjusted to allow for convergence with other fluids other than that which the traditional oil bearing code was designed for. In this study, the number of required elements across the film for improved prediction quality was calculated based on the proposed eddy-viscosity model mesh correction from the known literature. A comparison between water lubrication using the parameter correction and oil lubrication was also made. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 11 June 2018
- Published by ASME International
Turbulence Input Parameters Correction Methodology in Water Lubricated Thrust Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those found in the aerospace and automotive industries. However, environmental issues and risk-averse operations are resulting in the removal of oil and the replacement of all sealed oil bearings with reliable water-lubricated bearings. Due to the different fluid properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. This requires finer meshes when compared to oil-lubricated bearings as the low-viscosity fluid produces a very thin lubricant film. Analyzing water-lubricated bearings can also produce convergence and accuracy issues in traditional oil-based analysis codes. Thermal deformation largely affects oil-lubricated bearings, while having limited effects on water lubrication; mechanical deformation largely affects water lubrication, while its effects are typically lower than thermal deformation with oil. One common turbulence model used in these analysis tools is the eddy-viscosity model. Eddy-viscosity depends on the wall shear stress, therefore effective wall shear stress modeling is necessary in determining an appropriate turbulence model. Improving the accuracy and efficiency of modeling approaches for eddy-viscosity in turbulence models is of great importance. Therefore, the purpose of this study is to perform mesh refinement for water-lubricated bearings based on methodologies of eddy-viscosity modeling to improve their accuracy. According to Szeri [1], εm/v for the Boussinesq hypothesis is given by Reichardt’s formula. Fitting the velocity profile with experiments having a y+ in the range of 0–1,000 results in Ng-optimized Reichardt’s constants k = 0.4 and δ+ = 10.7. He clearly states that for y+ > 1000 theoretical predictions and experiments have a greater variance. Armentrout and others [2] developed an equation for δ+ as a function of the pivot Reynolds number, which they validated with CFD simulations. The definition of y+ can be used to approximate the first layer thickness calculated for a uniform mesh. Together with Armentrout’s equation, the number of required elements across the film thickness can be obtained. For typical turbulence models, the y+ must be within a certain range to be accurate. On the condition that the y+ is fixed to that of a standard oil bearing for which an oil bearing code was validated, the number of elements across the film thickness and coefficients used in the eddy-viscosity equation can be adjusted to allow for convergence with other fluids other than that which the traditional oil bearing code was designed for. In this study, the number of required elements across the film for improved prediction quality was calculated based on the proposed eddy-viscosity model mesh correction from the known literature. A comparison between water lubrication using the parameter correction and oil lubrication was also made. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 26 April 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (8)
Modeling Reichardt's Formula for Eddy Viscosity in the Fluid Film of Tilting Pad Thrust Bearings
Oil-lubricated bearings are widely used in high-speed rotating machines such as those used in the aerospace and automotive industries that often require this type of lubrication. However, environmental issues and risk-adverse operations have made water-lubricated bearings increasingly popular. Due to different viscosity properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. The turbulence model is affected by eddy viscosity, while eddy viscosity depends on wall shear stress. Therefore, effective wall shear stress modeling is necessary in producing an accurate turbulence model. Improving the accuracy and efficiency of methodologies of modeling eddy viscosity in the turbulence model is important, especially considering the increasingly popular application of water-lubricated bearings and also the traditional oil-lubricated bearings in high-speed machinery. This purpose of this paper is to study the sensitivity of using different methodologies of solving eddy viscosity for turbulence modeling. Eddy viscosity together with flow viscosity forms the effective viscosity, which is the coefficient of the shear stress in the film. The turbulence model and Reynolds equation are bound together to solve when hydrodynamic analysis is performed, therefore improving the accuracy of the turbulence model is also vital to improving a bearing model's ability to predict film pressure values, which will determine the velocity and velocity gradients in the film. The velocity gradients in the film are the other term determining the shear stress. In this paper, three approaches applying Reichardt's formula were used to model eddy viscosity in the fluid film. These methods are for determining where one wall's effects begin and the other wall's effects end. Trying to find a suitable model to capture the wall's effects of these bearings, with an aim to improve the accuracy of the turbulence model, would be of high value to the bearing industry. The results of this study could aid in improving future designs and models of both oil- and water-lubricated bearings.
- 26 April 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (8)
Modeling Reichardt's Formula for Eddy Viscosity in the Fluid Film of Tilting Pad Thrust Bearings
Oil-lubricated bearings are widely used in high-speed rotating machines such as those used in the aerospace and automotive industries that often require this type of lubrication. However, environmental issues and risk-adverse operations have made water-lubricated bearings increasingly popular. Due to different viscosity properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. The turbulence model is affected by eddy viscosity, while eddy viscosity depends on wall shear stress. Therefore, effective wall shear stress modeling is necessary in producing an accurate turbulence model. Improving the accuracy and efficiency of methodologies of modeling eddy viscosity in the turbulence model is important, especially considering the increasingly popular application of water-lubricated bearings and also the traditional oil-lubricated bearings in high-speed machinery. This purpose of this paper is to study the sensitivity of using different methodologies of solving eddy viscosity for turbulence modeling. Eddy viscosity together with flow viscosity forms the effective viscosity, which is the coefficient of the shear stress in the film. The turbulence model and Reynolds equation are bound together to solve when hydrodynamic analysis is performed, therefore improving the accuracy of the turbulence model is also vital to improving a bearing model's ability to predict film pressure values, which will determine the velocity and velocity gradients in the film. The velocity gradients in the film are the other term determining the shear stress. In this paper, three approaches applying Reichardt's formula were used to model eddy viscosity in the fluid film. These methods are for determining where one wall's effects begin and the other wall's effects end. Trying to find a suitable model to capture the wall's effects of these bearings, with an aim to improve the accuracy of the turbulence model, would be of high value to the bearing industry. The results of this study could aid in improving future designs and models of both oil- and water-lubricated bearings.
- 3 November 2017
- Published by ASME International
Modeling Reichardt’s Formula for Eddy-Viscosity in the Fluid Film of Tilting Pad Thrust Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those used in the aerospace and automotive industries that often require this type of lubrication. However, environmental issues and risk-adverse operations have made water lubricated bearings increasingly popular. Due to different viscosity properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. The turbulence model is affected by eddy-viscosity, while eddy-viscosity depends on wall shear stress. Therefore, effective wall shear stress modeling is necessary in producing an accurate turbulence model. Improving the accuracy and efficiency of methodologies of modeling eddy-viscosity in the turbulence model is important, especially considering the increasingly popular application of water-lubricated bearings and also the traditional oil-lubricated bearings in high speed machinery. This purpose of this paper is to study the sensitivity of using different methodologies of solving eddy-viscosity for turbulence modeling. Eddy-viscosity together with flow viscosity form the effective viscosity, which is the coefficient of the shear stress in the film. The turbulence model and Reynolds equation are bound together to solve when hydrodynamic analysis is performed, therefore improving the accuracy of the turbulence model is also vital to improving a bearing model’s ability to predict film pressure values, which will determine the velocity and velocity gradients in the film. The velocity gradients in the film are the other term determining the shear stress. In this paper, three approaches applying Reichardt’s formula were used to model eddy-viscosity in the fluid film. These methods are for determining where one wall’s effects begin and the other wall’s effects end. Trying to find a suitable model to capture the wall’s effects of these bearings, with aim to improve the accuracy of the turbulence model, would be of high value to the bearing industry. The results of this study could aid in improving future designs and models of both oil and water lubricated bearings.
- 3 November 2017
- Published by ASME International
Modeling Reichardt’s Formula for Eddy-Viscosity in the Fluid Film of Tilting Pad Thrust Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those used in the aerospace and automotive industries that often require this type of lubrication. However, environmental issues and risk-adverse operations have made water lubricated bearings increasingly popular. Due to different viscosity properties between oil and water, the low viscosity of water increases Reynolds numbers drastically and therefore makes water-lubricated bearings prone to turbulence effects. The turbulence model is affected by eddy-viscosity, while eddy-viscosity depends on wall shear stress. Therefore, effective wall shear stress modeling is necessary in producing an accurate turbulence model. Improving the accuracy and efficiency of methodologies of modeling eddy-viscosity in the turbulence model is important, especially considering the increasingly popular application of water-lubricated bearings and also the traditional oil-lubricated bearings in high speed machinery. This purpose of this paper is to study the sensitivity of using different methodologies of solving eddy-viscosity for turbulence modeling. Eddy-viscosity together with flow viscosity form the effective viscosity, which is the coefficient of the shear stress in the film. The turbulence model and Reynolds equation are bound together to solve when hydrodynamic analysis is performed, therefore improving the accuracy of the turbulence model is also vital to improving a bearing model’s ability to predict film pressure values, which will determine the velocity and velocity gradients in the film. The velocity gradients in the film are the other term determining the shear stress. In this paper, three approaches applying Reichardt’s formula were used to model eddy-viscosity in the fluid film. These methods are for determining where one wall’s effects begin and the other wall’s effects end. Trying to find a suitable model to capture the wall’s effects of these bearings, with aim to improve the accuracy of the turbulence model, would be of high value to the bearing industry. The results of this study could aid in improving future designs and models of both oil and water lubricated bearings.
- 30 July 2017
- Published by ASME International
Lubricant Inertia in Water Lubricated Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those used in the aerospace and automotive industries. However, with some applications including underwater machinery and environmentally friendly applications, water lubricated bearings have become increasingly used. Due to the different fluid properties between oil and water — namely viscosity — the use of water increases the Reynolds numbers drastically and, therefore, makes water-lubricated bearings prone to turbulence and fluid inertia effects. In other words, the linear approximation of the fluid film reaction forces due to the stiffness and damping parameters — as suggested in the traditional Reynolds equation — is not adequate and should be amended to include lubricant added mass. This is because water-lubricated bearings exhibit large lubricant inertia forces on the order of viscous forces. Additionally, stiffness and damping coefficients should be calculated with the turbulence effects included. The aim of this study was to investigate the methodology of modifying the traditional Reynolds equation to include lubricant inertia effects. This paper reviews the current status of research in the lubricant inertia of bearings and explores the development of methodologies to modify the Reynolds equation to include lubricant inertia in bearings. The Reynolds equation is a partial differential equation governing the pressure distribution of thin viscous fluid films in lubrication theory. The thin film hypothesis is used to directly relate the bearing film thickness to the lubricant film pressure. Adding lubricant inertia to the Reynolds equation is vital to improving the accuracy of the bearing model and more specifically its film pressure which is essential to predicting load carrying capabilities. The film pressure relates the gradient of the velocity tensor through the Reynolds equation, and resulting shear stresses then allow the turbulent momentum equations to be written in terms of an eddy-viscosity value. An extended Reynolds equation should be developed which takes into account turbulence and both convective and temporal inertia. The most complete form of the temporal inertia effect model should be developed and applied to the turbulent regime, consisting of both primary and secondary temporal inertia terms. The convective inertia model follows Constantinescu’s approach. This analysis develops a lubricant inertia model applicable to water-lubricated bearings. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 30 July 2017
- Published by ASME International
Lubricant Inertia in Water Lubricated Bearings
Oil-lubricated bearings are widely used in high speed rotating machines such as those used in the aerospace and automotive industries. However, with some applications including underwater machinery and environmentally friendly applications, water lubricated bearings have become increasingly used. Due to the different fluid properties between oil and water — namely viscosity — the use of water increases the Reynolds numbers drastically and, therefore, makes water-lubricated bearings prone to turbulence and fluid inertia effects. In other words, the linear approximation of the fluid film reaction forces due to the stiffness and damping parameters — as suggested in the traditional Reynolds equation — is not adequate and should be amended to include lubricant added mass. This is because water-lubricated bearings exhibit large lubricant inertia forces on the order of viscous forces. Additionally, stiffness and damping coefficients should be calculated with the turbulence effects included. The aim of this study was to investigate the methodology of modifying the traditional Reynolds equation to include lubricant inertia effects. This paper reviews the current status of research in the lubricant inertia of bearings and explores the development of methodologies to modify the Reynolds equation to include lubricant inertia in bearings. The Reynolds equation is a partial differential equation governing the pressure distribution of thin viscous fluid films in lubrication theory. The thin film hypothesis is used to directly relate the bearing film thickness to the lubricant film pressure. Adding lubricant inertia to the Reynolds equation is vital to improving the accuracy of the bearing model and more specifically its film pressure which is essential to predicting load carrying capabilities. The film pressure relates the gradient of the velocity tensor through the Reynolds equation, and resulting shear stresses then allow the turbulent momentum equations to be written in terms of an eddy-viscosity value. An extended Reynolds equation should be developed which takes into account turbulence and both convective and temporal inertia. The most complete form of the temporal inertia effect model should be developed and applied to the turbulent regime, consisting of both primary and secondary temporal inertia terms. The convective inertia model follows Constantinescu’s approach. This analysis develops a lubricant inertia model applicable to water-lubricated bearings. The results of this study could aid in improving future designs and models of water-lubricated bearings.
- 6 February 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 494-495, 645-650
Effects of Twisted and Cylindrical Blades on the Flow Characteristics inside Blade Inlet and Outlet for a Centrifugal Pump
In this paper, the performance between cylindrical and twisted blades are analyzed for the same centrifugal pump. The three-dimensional steady and unsteady flow fields under 0.7Qd, Qd and 1.3Qd are simulated. The blade inlet and outlet flow and pressure pulsation inside the centrifugal pumps are discussed by using mathematical statistics and frequency domain analysis methods. The research is verified by experiments. The results show that the twisted blade controls blade outlet better than cylindrical blade at small flow and design flow, cylindrical blade controls blade outlet better than twisted blade at large flow. In the blade inlet and outlet, as the flow changes, the instability of cylindrical blade loading is higher than that of twisted blade. The cylindrical blade inlet pressure is affected by the shaft frequency more than that of the twisted blade. At shaft frequency and blade frequency, pressure pulsation coefficient of cylindrical blade outlet is higher than that of twisted blade outlet. The cylindrical and twisted blades effect on the blade inlet and middle gradually accumulates, resulting twisted blade outlet has larger pressure pulsation. The result can guide the optimum design of centrifugal pump to consider the performance balance between twisted and cylindrical blades.
- 6 February 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 494-495, 645-650
Effects of Twisted and Cylindrical Blades on the Flow Characteristics inside Blade Inlet and Outlet for a Centrifugal Pump
In this paper, the performance between cylindrical and twisted blades are analyzed for the same centrifugal pump. The three-dimensional steady and unsteady flow fields under 0.7Qd, Qd and 1.3Qd are simulated. The blade inlet and outlet flow and pressure pulsation inside the centrifugal pumps are discussed by using mathematical statistics and frequency domain analysis methods. The research is verified by experiments. The results show that the twisted blade controls blade outlet better than cylindrical blade at small flow and design flow, cylindrical blade controls blade outlet better than twisted blade at large flow. In the blade inlet and outlet, as the flow changes, the instability of cylindrical blade loading is higher than that of twisted blade. The cylindrical blade inlet pressure is affected by the shaft frequency more than that of the twisted blade. At shaft frequency and blade frequency, pressure pulsation coefficient of cylindrical blade outlet is higher than that of twisted blade outlet. The cylindrical and twisted blades effect on the blade inlet and middle gradually accumulates, resulting twisted blade outlet has larger pressure pulsation. The result can guide the optimum design of centrifugal pump to consider the performance balance between twisted and cylindrical blades.