Gabrio Superti-Furga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Gabrio Superti-Furga has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Maria Stefania Carmeli
Politecnico di Milano, Milan, Italy
13 shared publications - Francesco Castelli-Dezza
Department of Mechanical Engineering, Politecnico di Milano, Milan, Italy
9 shared publications - Enrico Tironi
Dipartimento di Elettronica, Informatica e Bioingegneria, Politecnico di Milano, Milan Italy 20133
8 shared publications - Alessandro Ferrero
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
3 shared publications - Simone Barcellona
Department of Electronics, Information and Bioengineering, Politecnico di Milano, 20133 Milan, Italy
3 shared publications G. Ubezio
2 shared publications
Latest Publications
- 1 November 2021
- Published by Elsevier in Renewable Energy
- Vol. 177, 1133-1146
VSC-based LVDC distribution network with DERs: Equivalent circuits for leakage and ground fault currents evaluation
- 1 November 2021
- Published by Elsevier in Renewable Energy
- Vol. 177, 1133-1146
VSC-based LVDC distribution network with DERs: Equivalent circuits for leakage and ground fault currents evaluation
- 15 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 721-726
Space-vector approach in three-phase unbalance and distortion analysis
This paper shows that the space-vector approach is an eminent and powerful tool in three-phase analysis. It is able to manage in a unitary way the sinusoidal, distorted and transient conditions. Its complex Fourier series implements a formal unification between unbalance and distortion; such unification is conceptually significant and leads to simplification of principle, as well as powerful analytical processing. Examples illustrate the effectiveness of the complex Fourier series as analytical tool in different application areas.
- 15 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 721-726
Space-vector approach in three-phase unbalance and distortion analysis
This paper shows that the space-vector approach is an eminent and powerful tool in three-phase analysis. It is able to manage in a unitary way the sinusoidal, distorted and transient conditions. Its complex Fourier series implements a formal unification between unbalance and distortion; such unification is conceptually significant and leads to simplification of principle, as well as powerful analytical processing. Examples illustrate the effectiveness of the complex Fourier series as analytical tool in different application areas.
- 30 June 2015
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 44 (4) , 893-916
Swept area theory: an approach in nonlinear and switched network analysis
Summary: In this work, according to the concept of ‘area’ on the v–i plane, a new approach called swept area theory, under both nonlinear continuous and discontinuous conditions, is developed. Novel conservative functions, such as area velocity and closed area over time (CAT), involved in this theory, are proposed. An analysis is carried out, by means of these functions, over nonlinear R, L, and C elements and over the ideal switch. In addition, jump discontinuities are discussed in detail. The CAT is related to the harmonic reactive powers and under sinusoidal steady state becomes proportional to the classical reactive power. A balance rule concerning harmonic reactive powers over nonlinear resistor under continuous conditions is obtained and discussed as a novel interesting result. This aspect impacts on a possible expanded definition of reactive power under distorted conditions. Thanks to the switching power, a novel quantitative relation between hard‐switching commutations and CAT is obtained, with both theoretical and applicative relevance. More explanation is presented through a demonstration that shows how an ideal switch and power converters can become sources of reactive power. Issues of principle regarding the ideal switch model with respect to the real one are another important result of this work. Copyright © 2015 John Wiley & Sons, Ltd.
- 30 June 2015
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 44 (4) , 893-916
Swept area theory: an approach in nonlinear and switched network analysis
Summary: In this work, according to the concept of ‘area’ on the v–i plane, a new approach called swept area theory, under both nonlinear continuous and discontinuous conditions, is developed. Novel conservative functions, such as area velocity and closed area over time (CAT), involved in this theory, are proposed. An analysis is carried out, by means of these functions, over nonlinear R, L, and C elements and over the ideal switch. In addition, jump discontinuities are discussed in detail. The CAT is related to the harmonic reactive powers and under sinusoidal steady state becomes proportional to the classical reactive power. A balance rule concerning harmonic reactive powers over nonlinear resistor under continuous conditions is obtained and discussed as a novel interesting result. This aspect impacts on a possible expanded definition of reactive power under distorted conditions. Thanks to the switching power, a novel quantitative relation between hard‐switching commutations and CAT is obtained, with both theoretical and applicative relevance. More explanation is presented through a demonstration that shows how an ideal switch and power converters can become sources of reactive power. Issues of principle regarding the ideal switch model with respect to the real one are another important result of this work. Copyright © 2015 John Wiley & Sons, Ltd.
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Modified sequence circuits for asymmetrical three-phase loads
This work deals with the effects of asymmetric three-phase loads on the sequence circuits related to the symmetrical components transformation. It is shown that, under the assumption of a reactive load, asymmetry results in coupling of sequence circuits represented by means of an ideal transformer and a gyrator. The parameters of such coupling components are proportional to the deviation of the phase loads with respect to the symmetrical condition. The analysis holds for asymmetrical lines as well. The results are useful in two cases. First, for fast evaluations during simple circuit analysis. Second, for numerical implementation using commercial software for complex network analysis.
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Modified sequence circuits for asymmetrical three-phase loads
This work deals with the effects of asymmetric three-phase loads on the sequence circuits related to the symmetrical components transformation. It is shown that, under the assumption of a reactive load, asymmetry results in coupling of sequence circuits represented by means of an ideal transformer and a gyrator. The parameters of such coupling components are proportional to the deviation of the phase loads with respect to the symmetrical condition. The analysis holds for asymmetrical lines as well. The results are useful in two cases. First, for fast evaluations during simple circuit analysis. Second, for numerical implementation using commercial software for complex network analysis.
- 1 August 2014
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 15 (4) , 335-347
Augmented State Approach in Quasi-Sliding-Mode Controlled PEBB-Based Power Converters
A wide class of high power converters have modular structures as they are constituted of the connection of two-level modules, according to the power electronic building block (PEBB) concept. Moreover, the intrinsic variable structure nature of PEBBs makes sliding mode control an attractive solution. When complex configurations are considered the number of PEBBs can be different from the number of switching relations, and modularity concept is not still valid at control level. The present paper proposes and discusses a general and systematic approach which makes it possible to have a one-to-one correspondence between the number of PEBBs and the switching control laws. It makes it possible to preserve the modularity of PEBB allowing to have an embedded modulation strategy. In such a way, standard current-tracking algorithm can be applied at PEBB level. The approach is based on augmented state method and makes it possible to verify separately for each PEBB both sliding and reaching conditions. The proposed approach is verified and supported through simulation tests.
- 1 August 2014
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 15 (4) , 335-347
Augmented State Approach in Quasi-Sliding-Mode Controlled PEBB-Based Power Converters
A wide class of high power converters have modular structures as they are constituted of the connection of two-level modules, according to the power electronic building block (PEBB) concept. Moreover, the intrinsic variable structure nature of PEBBs makes sliding mode control an attractive solution. When complex configurations are considered the number of PEBBs can be different from the number of switching relations, and modularity concept is not still valid at control level. The present paper proposes and discusses a general and systematic approach which makes it possible to have a one-to-one correspondence between the number of PEBBs and the switching control laws. It makes it possible to preserve the modularity of PEBB allowing to have an embedded modulation strategy. In such a way, standard current-tracking algorithm can be applied at PEBB level. The approach is based on augmented state method and makes it possible to verify separately for each PEBB both sliding and reaching conditions. The proposed approach is verified and supported through simulation tests.
- 1 January 2014
- Published by Institution of Engineering and Technology (IET)
- p. 8.40
Direct current control of multilevel drive with novel floating capacitor control
- 1 January 2014
- Published by Institution of Engineering and Technology (IET)
- p. 8.40
Direct current control of multilevel drive with novel floating capacitor control
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5806-5811
Generalized master-slave current tracking for multiswitching converters with predictive slave algorithm
The large number of high power conversion applications has brought to the development of complex power converter configurations constituted of the connection of two-level modules. Modulation strategies based on master-slave approach take advantage of the modularity of these power converter topologies. The present paper proposes an improved master-slave control strategy where the choice of which module has to be switched is demanded to a separate predictive slave routine. Simulation tests validate the proposed control strategy.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5806-5811
Generalized master-slave current tracking for multiswitching converters with predictive slave algorithm
The large number of high power conversion applications has brought to the development of complex power converter configurations constituted of the connection of two-level modules. Modulation strategies based on master-slave approach take advantage of the modularity of these power converter topologies. The present paper proposes an improved master-slave control strategy where the choice of which module has to be switched is demanded to a separate predictive slave routine. Simulation tests validate the proposed control strategy.
- 1 March 2013
- Published by Elsevier in Electric Power Systems Research
- Vol. 96, 296-310
Comprehensive harmonic analysis of matrix converter under unbalanced/distorted conditions
- 1 March 2013
- Published by Elsevier in Electric Power Systems Research
- Vol. 96, 296-310
Comprehensive harmonic analysis of matrix converter under unbalanced/distorted conditions
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Active power control for flicker compensation in single phase welding machines
Power quality represents a crucial issue in low voltage distribution networks. Welding equipments are among the most polluting loads because of their strong nonlinear behavior and their highly intermittent working cycle with a degree of randomness which causes the phenomenon of voltage flicker. The usual approach to the flicker mitigation consists in the introduction of static VAr compensators connected near to the polluting load. However, in low voltage network it is not always possible to adopt this approach: often the resistance of the conductors is not negligible. This means that even the active power fluctuations may result in a significant flicker contribution. In this paper the Authors will propose a flicker compensation technique which does not require the installation of an external device. It has to be noticed that virtually all the modern welding machine power supplies include a rectifier and a capacitive DC link. Basically, the solution consists in exploiting the energy stored in the DC link capacitance in order to smooth and mitigate the active power fluctuations. The large variations of the DC link voltage (hence of the energy stored in the capacitance) controlled by proper energy storage management logic, allow a short-time peak shaving which results in a consistent reduction of the voltage flicker. Finally, the performance of the flicker reduction system will be evaluated by means of numerical simulations. In particular, the short time flicker severity Pst will be computed considering a mathematical model of a manual metal arc (MMA) welding power supply with and without the proposed control strategy.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Active power control for flicker compensation in single phase welding machines
Power quality represents a crucial issue in low voltage distribution networks. Welding equipments are among the most polluting loads because of their strong nonlinear behavior and their highly intermittent working cycle with a degree of randomness which causes the phenomenon of voltage flicker. The usual approach to the flicker mitigation consists in the introduction of static VAr compensators connected near to the polluting load. However, in low voltage network it is not always possible to adopt this approach: often the resistance of the conductors is not negligible. This means that even the active power fluctuations may result in a significant flicker contribution. In this paper the Authors will propose a flicker compensation technique which does not require the installation of an external device. It has to be noticed that virtually all the modern welding machine power supplies include a rectifier and a capacitive DC link. Basically, the solution consists in exploiting the energy stored in the DC link capacitance in order to smooth and mitigate the active power fluctuations. The large variations of the DC link voltage (hence of the energy stored in the capacitance) controlled by proper energy storage management logic, allow a short-time peak shaving which results in a consistent reduction of the voltage flicker. Finally, the performance of the flicker reduction system will be evaluated by means of numerical simulations. In particular, the short time flicker severity Pst will be computed considering a mathematical model of a manual metal arc (MMA) welding power supply with and without the proposed control strategy.
- 1 July 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2909-2914
Digital synchronous current control of Power Electronic Building Block in modular converters
The large number of high power conversion applications has brought to the development of complex power converter configurations. A wide class of such converters are based on Power Electronic Building Block (PEBB) constituted of two level modules. Modulation strategies can take advantage of the modularity of these power converter topologies proposing modular and general control strategies. The present paper proposes a predictive current tracking, constant frequency, controlled phase modulation algorithm based on PEBB concept. Simulation tests validate the proposed control strategy.
- 1 July 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2909-2914
Digital synchronous current control of Power Electronic Building Block in modular converters
The large number of high power conversion applications has brought to the development of complex power converter configurations. A wide class of such converters are based on Power Electronic Building Block (PEBB) constituted of two level modules. Modulation strategies can take advantage of the modularity of these power converter topologies proposing modular and general control strategies. The present paper proposes a predictive current tracking, constant frequency, controlled phase modulation algorithm based on PEBB concept. Simulation tests validate the proposed control strategy.