SMSenchun Miao

Senchun Miao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Senchun Miao has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Aerodynamic performance optimization and unsteady flow field stability analysis of a supercritical carbon dioxide centrifugal compressor with non-uniform blade tip clearance

    by Zhengjing Shen, Liuhao Liu, Jiangbo Wu, Senchun Miao, Xiaoze Du

    Tip leakage flow is a critical factor constraining the efficiency and stability of supercritical carbon dioxide (SCO2) centrifugal compressors. To address this challenge, this study proposes a non-uniform blade tip clearance design and establishes a parametric closed-loop optimization framework based on the NSGA-III algorithm to investigate its aerodynamic performance enhancement and unsteady flow dissipation suppression mechanisms. The results demonstrate that the optimized non-uniform clearance configuration significantly improves compressor performance, increasing the pressure ratio and isentropic efficiency by 3.55% and 5.65%, respectively, at the design point. Unsteady flow analysis reveals that the non-uniform clearance actively modulates the pressure gradient distribution in the tip region, effectively suppressing the scale and intensity of the tip leakage vortex and weakening the shear mixing between the leakage flow and the main flow. Consequently, the turbulent kinetic energy dissipation rate in the diffuser region is reduced by 33.08%. Entropy generation analysis further confirms a substantial reduction in irreversible energy losses in the tip region, with the average entropy generation rate at 0.9 BH (Blade Height) decreasing by 46.78%. Furthermore, the area-weighted average turbulent kinetic energy on the S1 stream surface is reduced by 10.4% globally, indicating a comprehensive improvement in flow stability. This study elucidates the physical mechanism by which non-uniform blade tip clearance enhances SCO2 compressor performance through flow structure reconstruction, providing a new theoretical basis and optimization pathway for high-performance turbomachinery design.


  • Drag reduction mechanism of blade with non-smooth surface in hydraulic pressure recovery turbine

    by Xiaohui Wang, Huzhong Jiang, Junhu Yang, Senchun Miao, Liping Chai

    The Hydraulic Pressure Recovery Turbine (HPRT) is a liquid pressure recovery device that plays a crucial role in enhancing efficiency, reducing costs, conserving energy, and achieving emissions reduction in process industries. To improve the hydraulic performance of the HPRT, this study employs non-smooth surface microstructures in the blade design for drag reduction, based on its energy dissipation characteristics. The effects of different microstructural units on hydraulic performance and their drag reduction mechanisms are explored. The results show that, under low-flow conditions, the hydraulic performance of the microstructures decreases. However, under design and high-flow conditions, efficiency improves significantly compared to the original model. Among the microstructures, the V-shaped microstructure demonstrates the most notable effect, with a roughly 2% increase in efficiency under design conditions. The mechanisms underlying the microstructures' effects are primarily reflected in two aspects: first, they suppress the formation of separation vortices on the pressure surface of the blades, reducing energy losses within the impeller; second, the microstructures generate secondary vortices that oppose the flow direction in the near-wall region. These vortices interact with the main flow, facilitating momentum transfer and broadening the low-speed flow region near the wall. This reduces the velocity gradient, thereby decreasing Reynolds stress and viscous resistance. Additionally, the reverse vortices within the microstructures function like “rolling bearings,” converting sliding friction into rolling friction, further reducing frictional resistance.


  • Unsteady flow analysis in a double-suction pump as turbine impeller based on finite-time Lyapunov exponent

    by Leqi Liu, Senchun Miao, Xiaohui Wang, Junhu Yang

    Pump as turbine (PAT) is an excellent energy recovery device. Understanding the flow characteristics of the key component, the impeller, is essential for further optimization and design of PAT. To analyze the unsteady flow characteristics inside the impeller of a double-suction PAT from a Lagrangian perspective, numerical simulations were conducted using the shear stress transport k–ω turbulence model for the design conditions. The finite-time Lyapunov exponent (FTLE) method was employed to extract the two-dimensional and three-dimensional Lagrangian coherent structures (LCSs) of the impeller over one cycle of unsteady velocity field. Results indicate that with time, the scale of the FTLE field gradually decreases, suggesting enhanced flow stability, reduced mixing efficiency, smoother flow structures, and increased flow convergence. In the two-dimensional perspective, high FTLE values concentrate at the inlet region of the passage, pressure side of the blades, and outlet region of the passage, spreading gradually over the entire blade surface, while low FTLE values predominantly concentrate on the blade surface with a diminishing area. The flow separation occurs at the leading edge of the impeller, the suction side of the impeller and the inlet region of the flow channel. In the three-dimensional perspective, different LCSs show varied changes at specific FTLE values, reflecting the impact of FTLE variation on the distribution of LCSs and indicating the evolution of flow states in fluid dynamics. Each moment of LCS exhibits a growth–stability–dissipation status transition. The FTLE method effectively reveals the flow variations inside the impeller of a double-suction PAT, offering a new perspective and tool for analyzing the turbulent structures in the complex flow field of PAT.


  • Unsteady flow analysis in a pump as turbine impeller based on proper orthogonal decomposition and dynamic mode decomposition methods

    by Senchun Miao, Leqi Liu, Xiaohui Wang, Junhu Yang

    Pump as turbine (PAT) is an efficient, simple, and cost-effective equipment combining pump and turbine and is one of the excellent energy recovery devices. It is helpful to master the flow characteristics of the key component impeller for the further optimization and design of the PAT. To analyze the unsteady flow features in the impeller of a double-suction pump operating as a turbine, numerical simulations were conducted using the shear stress transport (SST) k-ω turbulence model at the designed operating conditions. By utilizing proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) methods on the unsteady velocity field of a single cycle, the dominant modes up to the fourth order, along with their respective space–time information, can be extracted. The velocity field and vorticity field analysis were performed on the first four modes extracted using two different methods. Additionally, the vortex structures were extracted using the Ω method. The analysis demonstrates that the POD and DMD methods effectively decompose the intricate flow characteristics within the impeller into dynamic–static interference modes, fundamental modes, and dissipative modes. The dynamic–static interference mode is dominant, reflecting the flow characteristics influenced by the stationary components within the impeller. The vortex structure is mainly small tubular vortex and point vortex. The fundamental mode captures the steady flow field characteristics caused by the blade channel geometry. The vortex structure is mainly continuous tubular vortex and the diameter becomes larger. The dissipative mode reflects the flow separation generated on the blades by disturbances from the stationary components. The vortex structure is dominated by point vortex and discontinuous tubular vortex. Comparing the outcomes of the two modal analysis methods shows that the POD method has a distinct advantage in showcasing key changing nodes. In contrast, the DMD method is superior in isolating modes with a single frequency and in determining their stability.


  • Open Access

    Optimization of a Pipeline-Type Savonius Hydraulic Turbine

    by Xiaohui Wang, Kai Zhang, Xiaobang Bai, Senchun Miao, Zanxiu Wu, Jicheng Li

    This study focuses on a DN50 pipeline-type Savonius hydraulic turbine. The torque variation of the turbine in a rotation cycle is analyzed theoretically in the framework of the plane potential flow theory. Related numerical simulations show that the change in turbine torque is consistent with the theoretical analysis, with the main power zone and the secondary power zone exhibiting a positive torque. In contrast, the primary resistance zone and the secondary resistance zone are characterized by a negative torque. Analytical relationships between the turbine’s internal flow angle θ, the deflector’s inclination angle α0, and the coverage angle α of the power zone are introduced, and a method for calculating the optimal number of blades is proposed to maximize the power zone. Results are presented about performance tests conducted on five groups of hydraulic turbines with the blade number ranging from 3 to 7. Such results indicate that both the turbine’s recovery power and efficiency attain the highest values when the blade number is 4, which is in agreement with the number of blades calculated by the proposed method. Additionally, the study examines the effects of the flow rate on turbine parameters and the projected energy generation and cost savings for a specific pipeline configuration.


  • Experimental study of centrifugal pump as turbine with S-blade impeller

    by Xiaohui Wang, Zanxiu Wu, Hao Yang, Xingjie Zhang, Junhu Yang, Senchun Miao

    As a hydraulic energy recovery device, pump as turbine(PAT) has been applied widely in the seawater desalination and petrochemical industry. In order to improve the hydraulic performances, the blade inlet angle was redesigned by analyzing the velocity triangle of PAT impeller inlet, and an S-blade was proposed. Then, A new S-blade impeller was obtained by optimizing the impeller in a real case of centrifugal pump as turbine application, and it was compared with the original impeller through experiments. The results show that the efficiency of the new S-blade impeller is around 3% higher than that of the original blade with the fixed flow rate and head. Under the fixed speed, the shaft power of the new S-blade impeller is higher than that of the original blade, and the maximum deviation is 0.75 kW. The study could have important directive significance to blade optimization of PAT.


  • Open Access

    Optimization of pumps as turbines blades based on SVM-HDMR model and PSO algorithm

    by Bingxiao Jiang, Junhu Yang, Xiaohui Wang, Senchun Miao, Xiaobang Bai

    In view of the poor performance of pumps as turbines (PAT) operation, and the problem that the structural parameters cannot be optimized in the whole domain, the hybrid model of support vector machine (SVM) model and high-dimensional model representation (HDMR) method is applied to the optimization of PAT blade. Specifically, a PAT was selected, and the surrogate model for PAT blade optimization was constructed with MATLAB, Creo, and ANSYS software. The particle swarm optimization (PSO) algorithm was used to predict the performance data by global optimization. Finally, numerical prediction and experimental methods were used to verify the predicted data. These proved the applicability of the hybrid model in the optimization of fluid machinery. The numerical simulation results show that at the optimal operating point, the numerical simulation efficiency of the optimized PAT is 5.49% higher than that of the prototype PAT, and the output power is 7.2% higher. The test results show that the external characteristic curve of the numerical simulation PAT is basically consistent with the test results. At the optimal operating point, the test efficiency of the optimized PAT is 5.1% higher than that of the prototype PAT, and the output power is 6.9% higher.


  • Unsteady flow characteristics of energy conversion in impeller of centrifugal pump as turbine

    by Senchun Miao, Hongbiao Zhang, Jiawei Zhang, Xiaohui Wang, Fengxia Shi

    To study unsteady flow characteristics of energy conversion in impeller of centrifugal pump as turbine (PAT), the overall and sub-section methods are used to calculate the unsteady flow of the PAT under six working conditions. Through numerical calculations, the net input power of the impeller, the time domain change law of the fluid's work on the impeller, the time domain change law of power loss in the impeller, and the time domain change law of energy conversion in different regions of the impeller are analyzed. Results show that: the dynamic and static interference between the impeller blades and the tongue caused the fluctuation of energy conversion; with the increase of area between the head of the impeller blade and the opposite tongue, the power loss in the impeller decreases. And when the blade head completely deviates from the position of the tongue about 10°, the power loss in the impeller is minimized. The power output of the PAT at different flow rates is related to its internal flow conditions and the geometric structure of each region of the impeller. The above research results can provide guidance on how to operate the PAT impeller stably and efficiently.


  • Open Access

    A Study on the Unsteady Flow Characteristics and Energy Conversion in the Volute of a Pump-as-Turbine Device

    by Senchun Miao, Hongbiao Zhang, Wanglong Tian, Yinqiang Li

    To study the unsteady flow and related energy conversion process in the volute of a pump-as-turbine (PAT) device, six different working conditions have been considered. Through numerical calculation, the spatio-temporal variation of static pressure, dynamic pressure, total pressure and turbulent energy dissipation have been determined in each section of the volute. It is concluded that the reduction of the total power of two adjacent sections of the PAT volute is equal to the sum of the power lost by the fluid while moving from one section to the other and the power output from the two adjacent sections. For a fixed flow rate, the percentage of static pressure energy at the outlet of the PAT is roughly similar to that of the corresponding volute section, and both show a gradually increasing trend. The turbulent dissipation rate on each section of the PAT volute displays a similar a spatio-temporal behavior for different flow rates.