Eleni Douvi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eleni Douvi has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Dimitra Douvi
Paragon S.A., Pandosias 23, GR-11142 Athens, Greece
8 shared publications Dionissios P. Margaris
5 shared publicationsDimitra C. Douvi
3 shared publications- Haralabos-Theodoros Tsahalis
Paragon S.A., Pandosias 23, GR-11142 Athens, Greece
3 shared publications - Jason Tsahalis
Paragon S.A., Pandosias 23, GR-11142 Athens, Greece
3 shared publications Dionissios Margaris
Department of Mechanical Engineering and Aeronautics
2 shared publications
Latest Publications
- Open Access
- 2 February 2026
- Published by MDPI AG in Computation
- Vol. 14 (2) , 38
Development of a Dashboard for Simulation Workflow Visualization and Optimization of an Ammonia Synthesis Reactor in the HySTrAm Project (Horizon EU)
Although hydrogen plays a crucial role in the EU’s strategy to reduce greenhouse gas emissions, its storage and transport are technically challenging. If ammonia is produced efficiently, it can be a promising hydrogen carrier, especially in decentralized and flexible conditions. The Horizon EU HySTrAm project addresses this problem by developing a small-scale, containerized demonstration plant consisting of (1) a short-term hydrogen storage container using novel ultraporous materials optimized through machine learning, and (2) an ammonia synthesis reactor based on an improved low-pressure Haber–Bosch process. This paper presents an initial version of a Python (v3.9)-based dashboard designed to visualize and optimize the simulation workflow of the ammonia synthesis process. Designed as a baseline for a future online, automated tool, the dashboard allows the comparison of three reactor configurations already defined through simulations and aligned with the upcoming experimental campaign: single tube, two reactors in parallel swing mode and two reactors in series. Pressures at the inlet/outlet, temperatures across the reactor, operation recipe and ammonia production over time are displayed dynamically to evaluate the performance of the reactor. Future versions will include optimization features, such as the identification of optimal operating modes, the reduction of production time, an increase of productivity, and catalyst degradation estimation.
- 2 February 2026
- Published by MDPI AG in Computation
- Vol. 14 (2) , 38
Open AccessDevelopment of a Dashboard for Simulation Workflow Visualization and Optimization of an Ammonia Synthesis Reactor in the HySTrAm Project (Horizon EU)
Although hydrogen plays a crucial role in the EU’s strategy to reduce greenhouse gas emissions, its storage and transport are technically challenging. If ammonia is produced efficiently, it can be a promising hydrogen carrier, especially in decentralized and flexible conditions. The Horizon EU HySTrAm project addresses this problem by developing a small-scale, containerized demonstration plant consisting of (1) a short-term hydrogen storage container using novel ultraporous materials optimized through machine learning, and (2) an ammonia synthesis reactor based on an improved low-pressure Haber–Bosch process. This paper presents an initial version of a Python (v3.9)-based dashboard designed to visualize and optimize the simulation workflow of the ammonia synthesis process. Designed as a baseline for a future online, automated tool, the dashboard allows the comparison of three reactor configurations already defined through simulations and aligned with the upcoming experimental campaign: single tube, two reactors in parallel swing mode and two reactors in series. Pressures at the inlet/outlet, temperatures across the reactor, operation recipe and ammonia production over time are displayed dynamically to evaluate the performance of the reactor. Future versions will include optimization features, such as the identification of optimal operating modes, the reduction of production time, an increase of productivity, and catalyst degradation estimation.
- Open Access
- 1 February 2026
- Published by MDPI AG in Computation
- Vol. 14 (2) , 31
A Replication Study for Consumer Digital Twins: Pilot Sites Analysis and Experience from the SENDER Project (Horizon 2020)
The SENDER (Sustainable Consumer Engagement and Demand Response) project aims to develop an innovative interface that engages energy consumers in Demand Response (DR) programs by developing new technologies to predict energy consumption, enhance market flexibility, and manage the exploitation of Renewable Energy Sources (RES). The current paper presents a replication study for consumer Digital Twins (DTs) that simulate energy consumption patterns and occupancy behaviors in various households across three pilot sites (Austria, Spain, Finland) based on six-month historical and real-time data related to loads, sensors, and relevant details for every household. Due to data limitations and inhomogeneity, we conducted a replication analysis focusing only on Austria and Spain, where available data regarding power and motion alarm sensors were sufficient, leading to a replication scenario by gradually increasing the number of households. In addition to limited data and short time of measurements, other challenges faced included inconsistencies in sensor installations and limited information on occupancy. In order to ensure reliable results, data was filtered, and households with common characteristics were grouped together to improve accuracy and consistency in DT modeling. Finally, it was concluded that a successful replication procedure requires sufficient continuous, frequent, and homogeneous data, along with its validation.
- 1 February 2026
- Published by MDPI AG in Computation
- Vol. 14 (2) , 31
Open AccessA Replication Study for Consumer Digital Twins: Pilot Sites Analysis and Experience from the SENDER Project (Horizon 2020)
The SENDER (Sustainable Consumer Engagement and Demand Response) project aims to develop an innovative interface that engages energy consumers in Demand Response (DR) programs by developing new technologies to predict energy consumption, enhance market flexibility, and manage the exploitation of Renewable Energy Sources (RES). The current paper presents a replication study for consumer Digital Twins (DTs) that simulate energy consumption patterns and occupancy behaviors in various households across three pilot sites (Austria, Spain, Finland) based on six-month historical and real-time data related to loads, sensors, and relevant details for every household. Due to data limitations and inhomogeneity, we conducted a replication analysis focusing only on Austria and Spain, where available data regarding power and motion alarm sensors were sufficient, leading to a replication scenario by gradually increasing the number of households. In addition to limited data and short time of measurements, other challenges faced included inconsistencies in sensor installations and limited information on occupancy. In order to ensure reliable results, data was filtered, and households with common characteristics were grouped together to improve accuracy and consistency in DT modeling. Finally, it was concluded that a successful replication procedure requires sufficient continuous, frequent, and homogeneous data, along with its validation.
- Open Access
- 3 January 2026
- Published by MDPI AG in Computation
- Vol. 14 (1) , 9
A Consumer Digital Twin for Energy Demand Prediction: Development and Implementation Under the SENDER Project (HORIZON 2020)
This paper presents the development and implementation of a consumer Digital Twin (DT) for energy demand prediction under the SENDER (Sustainable Consumer Engagement and Demand Response) project, funded by HORIZON 2020. This project aims to engage consumers in the energy sector with innovative energy service applications to achieve proactive Demand Response (DR) and optimized usage of Renewable Energy Sources (RES). The proposed DT model is designed to digitally represent occupant behaviors and energy consumption patterns using Artificial Neural Networks (ANN), which enable continuous learning by processing real-time and historical data in different pilot sites and seasons. The DT development incorporates the International Energy Agency (IEA)—Energy in Buildings and Communities (EBC) Annex 66 and Drivers-Needs-Actions-Systems (DNAS) framework to standardize occupant behavior modeling. The research methodology consists of the following steps: (i) a mock-up simulation environment for three pilot sites was created, (ii) the DT was trained and calibrated using the artificial data from the previous step, and (iii) the DT model was validated with real data from the Alginet pilot site in Spain. Results showed a strong correlation between DT predictions and mock-up data, with a maximum deviation of ±2%. Finally, a set of selected Key Performance Indicators (KPIs) was defined and categorized in order to evaluate the system’s technical effectiveness.
- 3 January 2026
- Published by MDPI AG in Computation
- Vol. 14 (1) , 9
Open AccessA Consumer Digital Twin for Energy Demand Prediction: Development and Implementation Under the SENDER Project (HORIZON 2020)
This paper presents the development and implementation of a consumer Digital Twin (DT) for energy demand prediction under the SENDER (Sustainable Consumer Engagement and Demand Response) project, funded by HORIZON 2020. This project aims to engage consumers in the energy sector with innovative energy service applications to achieve proactive Demand Response (DR) and optimized usage of Renewable Energy Sources (RES). The proposed DT model is designed to digitally represent occupant behaviors and energy consumption patterns using Artificial Neural Networks (ANN), which enable continuous learning by processing real-time and historical data in different pilot sites and seasons. The DT development incorporates the International Energy Agency (IEA)—Energy in Buildings and Communities (EBC) Annex 66 and Drivers-Needs-Actions-Systems (DNAS) framework to standardize occupant behavior modeling. The research methodology consists of the following steps: (i) a mock-up simulation environment for three pilot sites was created, (ii) the DT was trained and calibrated using the artificial data from the previous step, and (iii) the DT model was validated with real data from the Alginet pilot site in Spain. Results showed a strong correlation between DT predictions and mock-up data, with a maximum deviation of ±2%. Finally, a set of selected Key Performance Indicators (KPIs) was defined and categorized in order to evaluate the system’s technical effectiveness.
- Open Access
Aerodynamic Characteristics of Wind Turbines Operating under Hazard Environmental Conditions: A Review
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorms, dust or sand, insects’ collisions, increased humidity, and sea spray, result in degraded aerodynamic characteristics. The outcome of most studies has been that the airfoils’ lift is degraded, and at the same time, drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of these crucial aspects so they are taken into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic characteristics of horizontal axis wind turbines.
Open AccessAerodynamic Characteristics of Wind Turbines Operating under Hazard Environmental Conditions: A Review
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorms, dust or sand, insects’ collisions, increased humidity, and sea spray, result in degraded aerodynamic characteristics. The outcome of most studies has been that the airfoils’ lift is degraded, and at the same time, drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of these crucial aspects so they are taken into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic characteristics of horizontal axis wind turbines.
- Open Access
- 29 September 2023
- Published by MDPI AG in Preprints.org
Aerodynamic Performance of Wind Turbines Operating under Hazard Environmental Conditions: A Review
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorm, dust or sand, insects’ collisions, increased humidity and sea spray, result in degraded aerodynamic performance. The outcome of the most studies is that lift is degraded and at the same time drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of the crucial aspects to take into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic performance of horizontal axis wind turbines.
- 29 September 2023
- Published by MDPI AG in Preprints.org
Open AccessAerodynamic Performance of Wind Turbines Operating under Hazard Environmental Conditions: A Review
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorm, dust or sand, insects’ collisions, increased humidity and sea spray, result in degraded aerodynamic performance. The outcome of the most studies is that lift is degraded and at the same time drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of the crucial aspects to take into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic performance of horizontal axis wind turbines.
- Open Access
- 23 December 2022
- Published by MDPI AG in Inventions
- Vol. 8 (1) , 3
Aerodynamic Performance of a Horizontal Axis Wind Turbine Operating with Dust—A Computational Study
The main purpose of this study is to develop an understanding of the aerodynamic performance of a horizontal axis wind turbine (HAWT) operating in a dusty environment, with various concentration of dust in the flow domain. The computational analysis was accomplished by the commercial computational fluid dynamics (CFD) code ANSYS Fluent 16.0. Initially, a user-friendly developed application was utilized for the optimum blade geometry special characteristics calculation. The design of the HAWT rotor and meshing of the computational domain follows. The moving reference frame (MRF) model was applied for the rotary motion of the blades, the dust was added in the computational domain by the discrete phase model (DPM) and SST k–ω turbulence model was enabled. The power output of the studied HAWT, operating in several dusty environments, was estimated and compared with the power output of a particular HAWT in clean air. The flow field around the HAWT rotor, including the contours of pressure, particles dissipation rate and erosion rate on both blade sides, are shown. In general, it is concluded that the operation of a HAWT in a dusty environment results in degraded performance, due to the particles deposition on the blades.
- 23 December 2022
- Published by MDPI AG in Inventions
- Vol. 8 (1) , 3
Open AccessAerodynamic Performance of a Horizontal Axis Wind Turbine Operating with Dust—A Computational Study
The main purpose of this study is to develop an understanding of the aerodynamic performance of a horizontal axis wind turbine (HAWT) operating in a dusty environment, with various concentration of dust in the flow domain. The computational analysis was accomplished by the commercial computational fluid dynamics (CFD) code ANSYS Fluent 16.0. Initially, a user-friendly developed application was utilized for the optimum blade geometry special characteristics calculation. The design of the HAWT rotor and meshing of the computational domain follows. The moving reference frame (MRF) model was applied for the rotary motion of the blades, the dust was added in the computational domain by the discrete phase model (DPM) and SST k–ω turbulence model was enabled. The power output of the studied HAWT, operating in several dusty environments, was estimated and compared with the power output of a particular HAWT in clean air. The flow field around the HAWT rotor, including the contours of pressure, particles dissipation rate and erosion rate on both blade sides, are shown. In general, it is concluded that the operation of a HAWT in a dusty environment results in degraded performance, due to the particles deposition on the blades.
- Open Access
Computational Approach of Charging and Discharging Phases in a Novel Compact Solar Collector with Integrated Thermal Energy Storage Tank: Study of Different Phase Change Materials
A numerical study was carried out to investigate charging and discharging processes of different phase change materials (PCMs) used for thermal storage in an innovative solar collector, targeting domestic hot water (DHW) requirements. The aim was to study PCMs that meet all application requirements, considering their thermal performance in terms of stored and retrieved energy, outlet temperatures, and water flow rate. Work was carried out for three flat-plate solar panels of different sizes. For each panel, a PCM tank with a heat exchanger was attached on the back plate. Simulations were conducted on a 2D domain using the enthalpy–porosity technique. Three paraffin-based PCMs were studied, two (A53, P53) with phase-change temperatures of approximately 53 °C and one of approximately 58 °C (A58H). Results showed that, during charging, A58H can store the most energy and A53 the least (12.30 kWh and 10.54 kWh, respectively, for the biggest unit). However, the biggest unit, A58H, takes the most time to be fully charged, i.e., 6.43 h for the fastest feed rate, while the A53 unit charges the fastest, at 4.25 h. The behavior of P53 lies in between A53 and A58H, considering stored energy and charging time. During discharging, all PCMs could provide an adequate DHW amount, even in the worst case, that is, a small unit with a high hot water consumption rate. The A58H unit provides hot water above 40 °C for 10 min, P53 for 11 min, and A53 for 12 min. The DHW production duration increased if a bigger unit was used or if the consumption rate was lower.
Open AccessComputational Approach of Charging and Discharging Phases in a Novel Compact Solar Collector with Integrated Thermal Energy Storage Tank: Study of Different Phase Change Materials
A numerical study was carried out to investigate charging and discharging processes of different phase change materials (PCMs) used for thermal storage in an innovative solar collector, targeting domestic hot water (DHW) requirements. The aim was to study PCMs that meet all application requirements, considering their thermal performance in terms of stored and retrieved energy, outlet temperatures, and water flow rate. Work was carried out for three flat-plate solar panels of different sizes. For each panel, a PCM tank with a heat exchanger was attached on the back plate. Simulations were conducted on a 2D domain using the enthalpy–porosity technique. Three paraffin-based PCMs were studied, two (A53, P53) with phase-change temperatures of approximately 53 °C and one of approximately 58 °C (A58H). Results showed that, during charging, A58H can store the most energy and A53 the least (12.30 kWh and 10.54 kWh, respectively, for the biggest unit). However, the biggest unit, A58H, takes the most time to be fully charged, i.e., 6.43 h for the fastest feed rate, while the A53 unit charges the fastest, at 4.25 h. The behavior of P53 lies in between A53 and A58H, considering stored energy and charging time. During discharging, all PCMs could provide an adequate DHW amount, even in the worst case, that is, a small unit with a high hot water consumption rate. The A58H unit provides hot water above 40 °C for 10 min, P53 for 11 min, and A53 for 12 min. The DHW production duration increased if a bigger unit was used or if the consumption rate was lower.
- Open Access
- 21 December 2021
- Published by MDPI AG in Inventions
- Vol. 7 (1) , 2
The Operation of a Three-Bladed Horizontal Axis Wind Turbine under Hailstorm Conditions—A Computational Study Focused on Aerodynamic Performance
The aim of this study is the aerodynamic degradation of a three-bladed Horizontal Axis Wind Turbine (HAWT) under the influence of a hailstorm. The importance and originality of this study are that it explores the aerodynamic performance of an optimum wind turbine blade during a hailstorm, when hailstones and raindrops are present. The commercial Computational Fluid Dynamics (CFD) code ANSYS Fluent 16.0 was utilized for the simulation. The first step was the calculation of the optimum blade geometry characteristics for a three-bladed rotor, i.e., twist and chord length along the blade, by a user-friendly application. Afterwards, the three-dimensional blade and the flow field domain were designed and meshed appropriately. The rotary motion of the blades was accomplished by the application of the Moving Reference Frame Model and the simulation of hailstorm conditions by the Discrete Phase Model. The SST k–ω turbulence model was also added. The produced power of the wind turbine, operating in various environmental conditions, was estimated and discussed. Contours of pressure, hailstone and raindrop concentration and erosion rate, on both sides of the blade, are presented. Moreover, contours of velocity at various cross sections parallel to the rotor are demonstrated, to understand the effect of hailstorms on the wake behavior. The results suggest that the aerodynamic performance of a HAWT degrades due to impact and breakup of the particles on the blade.
- 21 December 2021
- Published by MDPI AG in Inventions
- Vol. 7 (1) , 2
Open AccessThe Operation of a Three-Bladed Horizontal Axis Wind Turbine under Hailstorm Conditions—A Computational Study Focused on Aerodynamic Performance
The aim of this study is the aerodynamic degradation of a three-bladed Horizontal Axis Wind Turbine (HAWT) under the influence of a hailstorm. The importance and originality of this study are that it explores the aerodynamic performance of an optimum wind turbine blade during a hailstorm, when hailstones and raindrops are present. The commercial Computational Fluid Dynamics (CFD) code ANSYS Fluent 16.0 was utilized for the simulation. The first step was the calculation of the optimum blade geometry characteristics for a three-bladed rotor, i.e., twist and chord length along the blade, by a user-friendly application. Afterwards, the three-dimensional blade and the flow field domain were designed and meshed appropriately. The rotary motion of the blades was accomplished by the application of the Moving Reference Frame Model and the simulation of hailstorm conditions by the Discrete Phase Model. The SST k–ω turbulence model was also added. The produced power of the wind turbine, operating in various environmental conditions, was estimated and discussed. Contours of pressure, hailstone and raindrop concentration and erosion rate, on both sides of the blade, are presented. Moreover, contours of velocity at various cross sections parallel to the rotor are demonstrated, to understand the effect of hailstorms on the wake behavior. The results suggest that the aerodynamic performance of a HAWT degrades due to impact and breakup of the particles on the blade.
- Open Access
- 30 June 2021
- Published by The Scientific Club of Al Manahil Association in International Journal of Energetica
- Vol. 6 (1) , 25-33
Effect of Rain on the Aerodynamic Performance of a Horizontal Axis Wind Turbine – A Computational Study
This paper analyzes numerically the impact of rainfall on the aerodynamic performance of a three-bladed Horizontal Axis Wind Turbine, with blades constructed by NACA 4418 airfoil. The simulations were conducted by the help of the commercial Computational Fluid Dynamics code, ANSYS Fluent. Firstly, the optimum geometry of the blade was designed with an application based on Blade Element Momentum theory. The Moving Reference Frame Model was applicated to simulate the rotation of the blades and the k-ω shear-stress transport turbulence model was added as well. The simulation of rain was accomplished by the Discrete Phase Model and the Taylor Analogy Breakup model was enabled to simulate droplets breakup. Three different rainfall conditions were studied, corresponding to Liquid Water Contents of 10g/m³, 30g/m³ and 60g/m³. The influence of droplet diameter on the aerodynamic performance of the blade was also examined. The results showed that the aerodynamic performance of the wind turbine is degraded in rain conditions, and the degradation is greater for higher values of Liquid Water Content and for larger diameter of water droplets.
- 30 June 2021
- Published by The Scientific Club of Al Manahil Association in International Journal of Energetica
- Vol. 6 (1) , 25-33
Open AccessEffect of Rain on the Aerodynamic Performance of a Horizontal Axis Wind Turbine – A Computational Study
This paper analyzes numerically the impact of rainfall on the aerodynamic performance of a three-bladed Horizontal Axis Wind Turbine, with blades constructed by NACA 4418 airfoil. The simulations were conducted by the help of the commercial Computational Fluid Dynamics code, ANSYS Fluent. Firstly, the optimum geometry of the blade was designed with an application based on Blade Element Momentum theory. The Moving Reference Frame Model was applicated to simulate the rotation of the blades and the k-ω shear-stress transport turbulence model was added as well. The simulation of rain was accomplished by the Discrete Phase Model and the Taylor Analogy Breakup model was enabled to simulate droplets breakup. Three different rainfall conditions were studied, corresponding to Liquid Water Contents of 10g/m³, 30g/m³ and 60g/m³. The influence of droplet diameter on the aerodynamic performance of the blade was also examined. The results showed that the aerodynamic performance of the wind turbine is degraded in rain conditions, and the degradation is greater for higher values of Liquid Water Content and for larger diameter of water droplets.