Yangfan Liu
Yangfan Liu has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- J. Stuart Bolton
Ray W. Herrick Laboratories, School of Mechanical Engineering, Purdue University , 177 South Russell Street, West Lafayette, Indiana 47907-2099
3 shared publications - Davide Ziviani
Ray W. Herrick Laboratories, School of Mechanical Engineering, Purdue University 1 , 177 S. Russell Street, West Lafayette, Indiana 47907-2099
2 shared publications Dazhuang He
Purdue University
1 shared publication- Dazhuang He
Purdue University
1 shared publication - Gang Deng
Department of Radiology
1 shared publication - Guochenhao Song
Purdue Univ, Ray W Herrick Labs, 177 S Russell St, W Lafayette, IN 47907 USA
1 shared publication
Latest Publications
- 9 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2)
Foldable acoustic metamaterial for underwater broadband low-frequency noise mitigation
- 9 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2)
Foldable acoustic metamaterial for underwater broadband low-frequency noise mitigation
- 1 January 2024
- Published by Springer Nature
- p. 649-660
Multi-physical Modeling of Noise and Vibration Due to Refrigerant Discharge in Hermetic Compressors
- 1 January 2024
- Published by Springer Nature
- p. 649-660
Multi-physical Modeling of Noise and Vibration Due to Refrigerant Discharge in Hermetic Compressors
- 1 January 2024
- Published by Springer Nature
- p. 661-676
Mitigation of Fluid-Induced Noise Generated by Discharge Flow in a Hermetic Rolling Piston Compressor
- 1 January 2024
- Published by Springer Nature
- p. 661-676
Mitigation of Fluid-Induced Noise Generated by Discharge Flow in a Hermetic Rolling Piston Compressor
- 30 November 2023
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 268 (3) , 5890-5900
Approaches to address response variations in psychoacoustic tests focused on the assessment of tonal office noise
Tonal noise from information technology and service equipment is known to be a problem. A proper understanding of the annoyance due to tonal noise is valuable for guiding the design of a comfortable office environment. Earlier, authors have proposed and validated two types of annoyance metric models based on the psychoacoustic subjective tests conducted in an office mock-up, and further developed software to implement the models. Here, the focus is on analyzing the response variations observed in the tests: i.e., the tendency for subjects to give relative annoyance ratings instead of absolute ratings and differences in responses to longer and shorter stimuli. In addition, the approaches to incorporating response variations into the metric models are described. Note that the presented work is based on the studies of tonal office noises from service equipment, with the fundamental frequencies of interest being 29.5, 60, 120, 240, 500, 750, and 1000 Hz. However, the proposed approaches for evaluating tonalness and addressing response variations may be applicable to the study of tonal noises from information technology equipment.
- 30 November 2023
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 268 (3) , 5890-5900
Approaches to address response variations in psychoacoustic tests focused on the assessment of tonal office noise
Tonal noise from information technology and service equipment is known to be a problem. A proper understanding of the annoyance due to tonal noise is valuable for guiding the design of a comfortable office environment. Earlier, authors have proposed and validated two types of annoyance metric models based on the psychoacoustic subjective tests conducted in an office mock-up, and further developed software to implement the models. Here, the focus is on analyzing the response variations observed in the tests: i.e., the tendency for subjects to give relative annoyance ratings instead of absolute ratings and differences in responses to longer and shorter stimuli. In addition, the approaches to incorporating response variations into the metric models are described. Note that the presented work is based on the studies of tonal office noises from service equipment, with the fundamental frequencies of interest being 29.5, 60, 120, 240, 500, 750, and 1000 Hz. However, the proposed approaches for evaluating tonalness and addressing response variations may be applicable to the study of tonal noises from information technology equipment.
- Open Access
Development and external validation of a dynamic nomogram for delayed cerebral ischaemia after aneurysmal subarachnoid hemorrhage: a study protocol for a multicentre retrospective cohort study
Introduction Delayed cerebral ischaemia (DCI) caused by aneurysmal subarachnoid haemorrhage (aSAH) is the most frequent complication and typically contributes to poor neurological outcome or deterioration of patients’ condition. Therefore, early accurate and effective prediction of DCI is urgently needed. This study aims to construct a dynamic nomogram for precisely calculating the risk of DCI in patients with aSAH. Internal validation of this tool is conducted using the training cohort, and independent external validation is completed by using other medical centre datasets. Methods and analysis This study is a multicentre, retrospective, observational cohort study using data from patients with aSAH. The participants include all adult patients who received surgical treatment in neurosurgery of multiple medical centres from 1 September 2019 to 1 April 2021, including Renmin Hospital of Wuhan University, Huzhou Central Hospital, First Affiliated Hospital of Harbin Medical University, General Hospital of Northern Theatre Command and Affiliated Hospital of Panzhihua University. Clinical information is collected via the electronic medical record system, including demographic data, clinical state on admission and serum laboratory tests. Modified Fisher grade at admission, admission subarachnoid clot and cerebral oedema density, and residual postoperative subarachnoid clot density are determined using the electronic imagine record software. The primary outcome is DCI. Ethics and dissemination This study protocol was reviewed and approved by the Medical Ethics Committee of Renmin Hospital of Wuhan University, which is the principal affiliation of this study (approval number: WDRM2021-K022). The other Ethics Committees, including Huzhou Central Hospital (approval number: 202108005–01), First Affiliated Hospital of Harbin Medical University (approval number: H202156), General Hospital of Northern Theater Command (approval number: Y2021060) and Affiliated Hospital of Panzhihua University (approval number: 202105002), also approved the protocol. The results of this research will be published in a peer-reviewed medical journal. Trial registration number ChiCTR2100044448.
Open AccessDevelopment and external validation of a dynamic nomogram for delayed cerebral ischaemia after aneurysmal subarachnoid hemorrhage: a study protocol for a multicentre retrospective cohort study
Introduction Delayed cerebral ischaemia (DCI) caused by aneurysmal subarachnoid haemorrhage (aSAH) is the most frequent complication and typically contributes to poor neurological outcome or deterioration of patients’ condition. Therefore, early accurate and effective prediction of DCI is urgently needed. This study aims to construct a dynamic nomogram for precisely calculating the risk of DCI in patients with aSAH. Internal validation of this tool is conducted using the training cohort, and independent external validation is completed by using other medical centre datasets. Methods and analysis This study is a multicentre, retrospective, observational cohort study using data from patients with aSAH. The participants include all adult patients who received surgical treatment in neurosurgery of multiple medical centres from 1 September 2019 to 1 April 2021, including Renmin Hospital of Wuhan University, Huzhou Central Hospital, First Affiliated Hospital of Harbin Medical University, General Hospital of Northern Theatre Command and Affiliated Hospital of Panzhihua University. Clinical information is collected via the electronic medical record system, including demographic data, clinical state on admission and serum laboratory tests. Modified Fisher grade at admission, admission subarachnoid clot and cerebral oedema density, and residual postoperative subarachnoid clot density are determined using the electronic imagine record software. The primary outcome is DCI. Ethics and dissemination This study protocol was reviewed and approved by the Medical Ethics Committee of Renmin Hospital of Wuhan University, which is the principal affiliation of this study (approval number: WDRM2021-K022). The other Ethics Committees, including Huzhou Central Hospital (approval number: 202108005–01), First Affiliated Hospital of Harbin Medical University (approval number: H202156), General Hospital of Northern Theater Command (approval number: Y2021060) and Affiliated Hospital of Panzhihua University (approval number: 202105002), also approved the protocol. The results of this research will be published in a peer-reviewed medical journal. Trial registration number ChiCTR2100044448.
- 1 August 2021
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 263 (5) , 1471-1487
Vibrational Monitoring of Nested Planetary Geartrain with Unground Pinion
The nested planetary gear train, which has two integrated single-stage planetary gearsets, is one of the newly developed compound gear train that has been successfully applied to the automobile transmissions. In the current study, a certain type of gear fault in the nested gear train, ungrounded pinion, is investigated using a non-destructive approach monitoring its vibration levels. A novel experimental test stand with open and vertical setup has been designed to collect the vibrational data by mounting the accelerometer directly to the gear clutches. Each of the two layers of the compound gear was tested separately. The measured vibrational data were processed with several signal processing techniques, which includes (a) frequency spectrum analysis, (b) time synchronous averaging (TSA) and (c) modulation sideband analysis. The experimental results show that the existence of the ungrounded pinion can be identified with the frequency spectrum analysis of the vibrational data. In addition, the modulation sidebands are also modeled using a modified version of the traditional technique of physical signal modeling. It is shown that the relative phase of the planet and the meshing vibration strength changed by the unground gear is the critical factor for determining the modulation sideband behavior. In addition, the location of the ungrounded pinion can also be determined by the time history processed by TSA.
- 1 August 2021
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 263 (5) , 1471-1487
Vibrational Monitoring of Nested Planetary Geartrain with Unground Pinion
The nested planetary gear train, which has two integrated single-stage planetary gearsets, is one of the newly developed compound gear train that has been successfully applied to the automobile transmissions. In the current study, a certain type of gear fault in the nested gear train, ungrounded pinion, is investigated using a non-destructive approach monitoring its vibration levels. A novel experimental test stand with open and vertical setup has been designed to collect the vibrational data by mounting the accelerometer directly to the gear clutches. Each of the two layers of the compound gear was tested separately. The measured vibrational data were processed with several signal processing techniques, which includes (a) frequency spectrum analysis, (b) time synchronous averaging (TSA) and (c) modulation sideband analysis. The experimental results show that the existence of the ungrounded pinion can be identified with the frequency spectrum analysis of the vibrational data. In addition, the modulation sidebands are also modeled using a modified version of the traditional technique of physical signal modeling. It is shown that the relative phase of the planet and the meshing vibration strength changed by the unground gear is the critical factor for determining the modulation sideband behavior. In addition, the location of the ungrounded pinion can also be determined by the time history processed by TSA.
- 1 September 2017
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 65 (5) , 406-416
Prediction of sound fields radiated by finite-size sources in room environments by using equivalent source models: three-dimensional simulation and validation
The use of equivalent source models (ESM) has recently been extended, with appropriate modifications, from its original application in acoustical holography to room acoustics simulations. This approach can serve as an alternative that is less computationally intense than the boundary element method and which is more flexible than traditional ray-tracing models in terms of dealing with non-compact sources and lower frequencies where the ray approximation is no longer accurate. Such room acoustics ESMs are based on the assumption that the room component of the total sound field can be represented by a number of equivalent sources of certain types, and that the total sound field can be predicted, with given free-space source information, by estimating the strengths of these equivalent sources based on a least-square match of the impedance boundary conditions on both the source and the room surfaces. However, to-date, the room acoustics ESMs have only been formulated and validated for two-dimensional cases. In the current work, the ESM formulation has been extended to three dimensions by replacing the two-dimensional equivalent sources with their three-dimensional counterparts, and its applications in a realistic three-dimensional room environment has been validated by successfully comparing the ESM and boundary element predictions.
- 1 September 2017
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 65 (5) , 406-416
Prediction of sound fields radiated by finite-size sources in room environments by using equivalent source models: three-dimensional simulation and validation
The use of equivalent source models (ESM) has recently been extended, with appropriate modifications, from its original application in acoustical holography to room acoustics simulations. This approach can serve as an alternative that is less computationally intense than the boundary element method and which is more flexible than traditional ray-tracing models in terms of dealing with non-compact sources and lower frequencies where the ray approximation is no longer accurate. Such room acoustics ESMs are based on the assumption that the room component of the total sound field can be represented by a number of equivalent sources of certain types, and that the total sound field can be predicted, with given free-space source information, by estimating the strengths of these equivalent sources based on a least-square match of the impedance boundary conditions on both the source and the room surfaces. However, to-date, the room acoustics ESMs have only been formulated and validated for two-dimensional cases. In the current work, the ESM formulation has been extended to three dimensions by replacing the two-dimensional equivalent sources with their three-dimensional counterparts, and its applications in a realistic three-dimensional room environment has been validated by successfully comparing the ESM and boundary element predictions.
- 1 August 2016
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 140 (2) , EL149-EL153
On the completeness and the linear dependence of the Cartesian multipole series in representing the solution to the Helmholtz equation
The (Cartesian) multipole series, i.e., the series comprising monopole, dipoles, quadrupoles, etc., can be used, as an alternative to the spherical or cylindrical wave series, in representing sound fields in a wide range of problems, such as source radiation, sound scattering, etc. The proofs of the completeness of the spherical and cylindrical wave series in these problems are classical results, and it is also generally agreed that the Cartesian multipole series spans the same space as the spherical waves: a rigorous mathematical proof of that statement has, however, not been presented. In the present work, such a proof of the completeness of the Cartesian multipole series, both in two and three dimensions, is given, and the linear dependence relations among different orders of multipoles are discussed, which then allows one to easily extract a basis from the multipole series. In particular, it is concluded that the multipoles comprising the two highest orders in the series form a basis of the whole series, since the multipoles of all the lower source orders can be expressed as a linear combination of that basis.
- 1 August 2016
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 140 (2) , EL149-EL153
On the completeness and the linear dependence of the Cartesian multipole series in representing the solution to the Helmholtz equation
The (Cartesian) multipole series, i.e., the series comprising monopole, dipoles, quadrupoles, etc., can be used, as an alternative to the spherical or cylindrical wave series, in representing sound fields in a wide range of problems, such as source radiation, sound scattering, etc. The proofs of the completeness of the spherical and cylindrical wave series in these problems are classical results, and it is also generally agreed that the Cartesian multipole series spans the same space as the spherical waves: a rigorous mathematical proof of that statement has, however, not been presented. In the present work, such a proof of the completeness of the Cartesian multipole series, both in two and three dimensions, is given, and the linear dependence relations among different orders of multipoles are discussed, which then allows one to easily extract a basis from the multipole series. In particular, it is concluded that the multipoles comprising the two highest orders in the series form a basis of the whole series, since the multipoles of all the lower source orders can be expressed as a linear combination of that basis.
- 1 January 2013
- Published by Acoustical Society of America (ASA) in Proceedings of Meetings on Acoustics
- Vol. 19 (1) , 015130
The use of equivalent source models for reduced order simulation in room acoustics
The sound field in a room can be accurately predicted for a given source type and room surface boundary conditions (such as surface normal impedance) by using the Boundary Element Method. However, this approach is usually time-consuming, especially at high frequencies. For the purpose of increasing the computation speed, an alternative approach based on an Equivalent Source Model (ESM) has been adopted which makes it possible to avoid numerical integrations on the boundary elements. Boundary conditions on the boundary surfaces are used to estimate the parameters of the ESM which represents the room component of the total sound field. Along with a "traditional" ESM in which monopoles are distributed outside the room region, a Multipole ESM was developed for this room acoustics application: it consists of monopoles, dipoles, quadrupoles, etc. It has been found, in principle and also through a two-dimensional simulation for a circular room, that the Multipole ESM has the benefits of a large feasible frequency range, a relatively low model order, and the possibility of balancing the prediction accuracy and the computational intensity flexibly by the choice of the highest source order included in the Multipole model structure.
- 1 January 2013
- Published by Acoustical Society of America (ASA) in Proceedings of Meetings on Acoustics
- Vol. 19 (1) , 015130
The use of equivalent source models for reduced order simulation in room acoustics
The sound field in a room can be accurately predicted for a given source type and room surface boundary conditions (such as surface normal impedance) by using the Boundary Element Method. However, this approach is usually time-consuming, especially at high frequencies. For the purpose of increasing the computation speed, an alternative approach based on an Equivalent Source Model (ESM) has been adopted which makes it possible to avoid numerical integrations on the boundary elements. Boundary conditions on the boundary surfaces are used to estimate the parameters of the ESM which represents the room component of the total sound field. Along with a "traditional" ESM in which monopoles are distributed outside the room region, a Multipole ESM was developed for this room acoustics application: it consists of monopoles, dipoles, quadrupoles, etc. It has been found, in principle and also through a two-dimensional simulation for a circular room, that the Multipole ESM has the benefits of a large feasible frequency range, a relatively low model order, and the possibility of balancing the prediction accuracy and the computational intensity flexibly by the choice of the highest source order included in the Multipole model structure.