Xu Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xu Liu has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Xiaojing Hao
Australian Centre for Advanced Photovoltaics, School of Photovoltaic and Renewable Energy Engineering, University of New South Wales, Sydney, Australia
8 shared publications - Jialiang Huang
Australian Centre for Advanced Photovoltaics, School of Photovoltaic and Renewable Energy Engineering, University of New South Wales, Sydney, Australia
6 shared publications - Kaiwen Sun
Australian Centre for Advanced Photovoltaics School of Photovoltaic and Renewable Energy Engineering University of New South Wales Sydney Australia
5 shared publications - Martin Andrew Green
School of Photovoltaic and Renewable Energy Engineering University of New South Wales Sydney New South Wales Australia
5 shared publications - Jan Seidel
School of Materials Science and Engineering, University of New South Wales, Sydney, Australia
4 shared publications - John Arron Stride
School of Chemistry, University of New South Wales, Sydney, Australia
3 shared publications
Latest Publications
- Open Access
- 13 July 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (9) , 1332-1340
Early-stage local chemistry regulation enabling open-circuit voltage of 847 mV in wide-bandgap Cu2ZnSnS4 solar cells
Wide-bandgap kesterite Cu 2 ZnSnS 4 (CZTS) is a promising top-cell candidate for tandem photovoltaics, yet its progress is limited by persistent open-circuit voltage ( V OC ) deficits. Previous reports of wide-bandgap CZTS solar cells have exhibited substantial V OC losses relative to the radiative limit, largely due to a mismatch between the designed global composition and the local chemistry formed during early crystallization, where elemental diffusion induces secondary phases and detrimental defects. Here we demonstrate a defect regulation strategy that stabilizes the local chemical environment and suppresses diffusion-induced secondary phases, therefore maintaining the desired crystallization environment and pathway. This approach promotes benign defects over detrimental ones, thereby reducing non-radiative recombination losses. Consequently, we achieve a certified champion V OC of 847 mV (65.3% of the radiative limit) and an efficiency of 12.4% in Cd-free wide-bandgap CZTS solar cells. This defect regulation strategy provides a generalized insight into the synthesis of multinary compound semiconductors.
- 13 July 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (9) , 1332-1340
Open AccessEarly-stage local chemistry regulation enabling open-circuit voltage of 847 mV in wide-bandgap Cu2ZnSnS4 solar cells
Wide-bandgap kesterite Cu 2 ZnSnS 4 (CZTS) is a promising top-cell candidate for tandem photovoltaics, yet its progress is limited by persistent open-circuit voltage ( V OC ) deficits. Previous reports of wide-bandgap CZTS solar cells have exhibited substantial V OC losses relative to the radiative limit, largely due to a mismatch between the designed global composition and the local chemistry formed during early crystallization, where elemental diffusion induces secondary phases and detrimental defects. Here we demonstrate a defect regulation strategy that stabilizes the local chemical environment and suppresses diffusion-induced secondary phases, therefore maintaining the desired crystallization environment and pathway. This approach promotes benign defects over detrimental ones, thereby reducing non-radiative recombination losses. Consequently, we achieve a certified champion V OC of 847 mV (65.3% of the radiative limit) and an efficiency of 12.4% in Cd-free wide-bandgap CZTS solar cells. This defect regulation strategy provides a generalized insight into the synthesis of multinary compound semiconductors.
- Top Cited PapersOpen Access
- 14 January 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (3) , 415-424
Regulation of hydrothermal reaction kinetics with sodium sulfide for certified 10.7% efficiency Sb2(S,Se)3 solar cells
Antimony chalcogenide (Sb 2 (S,Se) 3 ) is a promising candidate for next-generation photovoltaic materials due to its optoelectronic properties, high absorption coefficient and material availability. Hydrothermal deposition has advanced the technology, but there is a limited understanding of the underlying reaction mechanisms, often resulting in non-ideal valence band maximum gradient across the absorber thickness and high concentration of deep-level defects. Here we introduce sodium sulfide as an additive in the precursor solution to control reaction kinetics. This strategy enables a more uniform depth-dependent elemental distribution, flattens the unfavourable valence band maximum gradient across the depth and suppresses the formation of deep-level defects. We demonstrate an improvement in Sb 2 (S,Se) 3 material quality, achieving a power conversion efficiency of 11.02%, with a certified value of 10.7 ± 0.37%. This work advances the efficiency for Sb 2 (S,Se) 3 solar cells and provides insights to optimize the hydrothermal synthesis for this technology.
- 14 January 2026
- Published by Springer Nature in Nature Energy
- Vol. 11 (3) , 415-424
Top Cited PapersOpen AccessRegulation of hydrothermal reaction kinetics with sodium sulfide for certified 10.7% efficiency Sb2(S,Se)3 solar cells
Antimony chalcogenide (Sb 2 (S,Se) 3 ) is a promising candidate for next-generation photovoltaic materials due to its optoelectronic properties, high absorption coefficient and material availability. Hydrothermal deposition has advanced the technology, but there is a limited understanding of the underlying reaction mechanisms, often resulting in non-ideal valence band maximum gradient across the absorber thickness and high concentration of deep-level defects. Here we introduce sodium sulfide as an additive in the precursor solution to control reaction kinetics. This strategy enables a more uniform depth-dependent elemental distribution, flattens the unfavourable valence band maximum gradient across the depth and suppresses the formation of deep-level defects. We demonstrate an improvement in Sb 2 (S,Se) 3 material quality, achieving a power conversion efficiency of 11.02%, with a certified value of 10.7 ± 0.37%. This work advances the efficiency for Sb 2 (S,Se) 3 solar cells and provides insights to optimize the hydrothermal synthesis for this technology.
- 1 July 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (27) , 24508-24535
Self-Assembled Monolayers for Perovskite Solar Cells: Molecular Design and Chemical Synthesis
Self-assembled monolayers (SAMs) have been a game-changer for perovskite solar cells (PSCs), significantly boosting their power conversion efficiency (PCE) to 27% in recent years. This breakthrough has garnered unprecedented attention, leading to significant advancements in the design and synthesis of SAM molecules (SAMols). Additionally, SAMs hold significant promise in addressing the lifetime of PSCs and facilitating their commercialization in terms of diversity, flexibility, and multifunctionality. To date, despite the development of numerous types of SAMols, challenges remain in designing and synthesizing optimal SAMols and achieving ultrastable devices that maintain outstanding PCEs. In this review, we systematically present recent advances in the design of SAMols, focusing on representative examples that have been employed in PSCs. Subsequently, a comprehensive overview of various synthetic pathways for these SAMols is provided for screening the most suitable synthesis method for target SAMols. Finally, challenges and potential opportunities for PSCs applications are highlighted.
- 1 July 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (27) , 24508-24535
Self-Assembled Monolayers for Perovskite Solar Cells: Molecular Design and Chemical Synthesis
Self-assembled monolayers (SAMs) have been a game-changer for perovskite solar cells (PSCs), significantly boosting their power conversion efficiency (PCE) to 27% in recent years. This breakthrough has garnered unprecedented attention, leading to significant advancements in the design and synthesis of SAM molecules (SAMols). Additionally, SAMs hold significant promise in addressing the lifetime of PSCs and facilitating their commercialization in terms of diversity, flexibility, and multifunctionality. To date, despite the development of numerous types of SAMols, challenges remain in designing and synthesizing optimal SAMols and achieving ultrastable devices that maintain outstanding PCEs. In this review, we systematically present recent advances in the design of SAMols, focusing on representative examples that have been employed in PSCs. Subsequently, a comprehensive overview of various synthetic pathways for these SAMols is provided for screening the most suitable synthesis method for target SAMols. Finally, challenges and potential opportunities for PSCs applications are highlighted.
- 8 December 2022
- Published by Springer Nature in Nature Photonics
- Vol. 17 (1) , 96-105
Perovskite solar cells based on spiro-OMeTAD stabilized with an alkylthiol additive
- 8 December 2022
- Published by Springer Nature in Nature Photonics
- Vol. 17 (1) , 96-105
Perovskite solar cells based on spiro-OMeTAD stabilized with an alkylthiol additive
- Open Access
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Research on Thermal-Mechanical Properties of GaN Power Module Based on QFN Package by Using Nano Copper/Silver Sinter Paste
The wide-bandgap semiconductors represented by GaN have a broad application prospect because of their high service temperature and high switch frequency. Quad-Flat-No-Lead (QFN) Package is currently one of the mainstream packaging methods due to its low cost and high efficiency. However, the low reliability of QFN used in GaN devices is still a crucial problem caused by elevated temperatures and the thermal stress induced by the mismatch of coefficient of thermal expansion (CTE). Therefore, it is necessary to control the temperature inner the package and increase the mechanical property of the bonding layer. In this paper, the finite element method (FEM) with thermal-mechanical coupling is performed to optimize the reliability of the bonding layer by adopting sinter nano Cu and silver. Based on the conventional QFN package module, we tried to add different metallization on the bonding surface to decrease the influence of CTE mismatch. We should note that the Anand viscoplastic model was used in the materials of Sintered Ag and lead-free solder paste presented by SAC305, which were the most commonly used in die-attachment. The results showed that the utilization of nano copper/silver paste could hardly facilitate thermal performance although sintered Ag had excellent thermal conductivity. Since the Anand modules of Ag and SAC305 were different, there were some impacts on the stress distribution and deformation. During the bonding process, a large thermal stress generated between die-attachment layer and Package or the PCB. The die-attachment layer formed by nano Ag paste suffered the smaller thermal stress because its CTE is comparable to that of thermal pad. In terms of sintered Ag, the bonding layer generated more elastic strain. As the deformation recovered to initial stage, the stress decreased because of the elastic strain. And we also found that the Ag metallization could decreased the maximum stress of model at heating stage. But Ag metallization suffered larger thermal stress as the temperature decreased. The selection of connection materials and metallization are a crucial part of design the structure of electronic package. And this paper could provide a reference for optimize the package structure to further improve their reliability in future works.
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Open AccessResearch on Thermal-Mechanical Properties of GaN Power Module Based on QFN Package by Using Nano Copper/Silver Sinter Paste
The wide-bandgap semiconductors represented by GaN have a broad application prospect because of their high service temperature and high switch frequency. Quad-Flat-No-Lead (QFN) Package is currently one of the mainstream packaging methods due to its low cost and high efficiency. However, the low reliability of QFN used in GaN devices is still a crucial problem caused by elevated temperatures and the thermal stress induced by the mismatch of coefficient of thermal expansion (CTE). Therefore, it is necessary to control the temperature inner the package and increase the mechanical property of the bonding layer. In this paper, the finite element method (FEM) with thermal-mechanical coupling is performed to optimize the reliability of the bonding layer by adopting sinter nano Cu and silver. Based on the conventional QFN package module, we tried to add different metallization on the bonding surface to decrease the influence of CTE mismatch. We should note that the Anand viscoplastic model was used in the materials of Sintered Ag and lead-free solder paste presented by SAC305, which were the most commonly used in die-attachment. The results showed that the utilization of nano copper/silver paste could hardly facilitate thermal performance although sintered Ag had excellent thermal conductivity. Since the Anand modules of Ag and SAC305 were different, there were some impacts on the stress distribution and deformation. During the bonding process, a large thermal stress generated between die-attachment layer and Package or the PCB. The die-attachment layer formed by nano Ag paste suffered the smaller thermal stress because its CTE is comparable to that of thermal pad. In terms of sintered Ag, the bonding layer generated more elastic strain. As the deformation recovered to initial stage, the stress decreased because of the elastic strain. And we also found that the Ag metallization could decreased the maximum stress of model at heating stage. But Ag metallization suffered larger thermal stress as the temperature decreased. The selection of connection materials and metallization are a crucial part of design the structure of electronic package. And this paper could provide a reference for optimize the package structure to further improve their reliability in future works.
- 1 December 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 147, 106750
Background suppression with dual modulation by saturated absorption competition microscopy
- 1 December 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 147, 106750
Background suppression with dual modulation by saturated absorption competition microscopy
- 25 October 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (44) , 49648-49658
Rising from the Ashes: Gaseous Therapy for Robust and Large-Area Perovskite Solar Cells
Scalable fabrication of perovskite solar cells (PSCs) with high reliability is one of the most pivotal concerns that must be addressed before they get into the photovoltaic (PV) market. Scaling large-area high-quality perovskite films is of great importance in this process. Here, gaseous therapy has been proposed for the post-treatment of perovskite films with high scalability and low cost. An inspiring evolvement from poor perovskite films to high quality ones is demonstrated under a joint treatment of methylamine gas and hot solvent vapors. The perovskite films are completely reconstructed and repaired regardless of the morphology of the original films. As a consequence, small-area (0.09 cm2) and large-area (4 cm2) PSCs based on the healed MAPbI3 films can afford J–V scanned efficiencies of 19.2 and 16.5% under a reverse sweep, respectively. Furthermore, stabilized power outputs of 18.5 and 15.2% are obtained from the small one and large one under continuous maximum power point tracking.
- 25 October 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (44) , 49648-49658
Rising from the Ashes: Gaseous Therapy for Robust and Large-Area Perovskite Solar Cells
Scalable fabrication of perovskite solar cells (PSCs) with high reliability is one of the most pivotal concerns that must be addressed before they get into the photovoltaic (PV) market. Scaling large-area high-quality perovskite films is of great importance in this process. Here, gaseous therapy has been proposed for the post-treatment of perovskite films with high scalability and low cost. An inspiring evolvement from poor perovskite films to high quality ones is demonstrated under a joint treatment of methylamine gas and hot solvent vapors. The perovskite films are completely reconstructed and repaired regardless of the morphology of the original films. As a consequence, small-area (0.09 cm2) and large-area (4 cm2) PSCs based on the healed MAPbI3 films can afford J–V scanned efficiencies of 19.2 and 16.5% under a reverse sweep, respectively. Furthermore, stabilized power outputs of 18.5 and 15.2% are obtained from the small one and large one under continuous maximum power point tracking.
- 24 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (20) , 22825-22834
Quasi-Vertically-Orientated Antimony Sulfide Inorganic Thin-Film Solar Cells Achieved by Vapor Transport Deposition
The one-dimensional photovoltaic absorber material Sb2S3 requires crystal orientation engineering to enable efficient carrier transport. In this work, we adopted a vapor transport deposition (VTD) method to fabricate vertically aligned Sb2S3 on a CdS buffer layer. Our work shows that such a preferential vertical orientation arises from the sulfur deficit of the CdS surface which creates a beneficial bonding environment between exposed Cd2+ dangling bonds and S atoms in the Sb2S3 molecules. The CdS/VTD-Sb2S3 interface recombination is suppressed by such properly aligned ribbons at the interface. Compared with typical [120]-oriented Sb2S3 films deposited on CdS by rapid thermal evaporation (RTE) method, the VTD-Sb2S3 thin film is highly [211]- and [121]- oriented and the performance of the solar cell is increased considerably. Without using any hole transportation layer, a conversion efficiency of 4.73% is achieved with device structure of ITO/CdS/Sb2S3/Au. This work provides a potential way to acquire vertical aligned thin films on different buffer layers.
- 24 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (20) , 22825-22834
Quasi-Vertically-Orientated Antimony Sulfide Inorganic Thin-Film Solar Cells Achieved by Vapor Transport Deposition
The one-dimensional photovoltaic absorber material Sb2S3 requires crystal orientation engineering to enable efficient carrier transport. In this work, we adopted a vapor transport deposition (VTD) method to fabricate vertically aligned Sb2S3 on a CdS buffer layer. Our work shows that such a preferential vertical orientation arises from the sulfur deficit of the CdS surface which creates a beneficial bonding environment between exposed Cd2+ dangling bonds and S atoms in the Sb2S3 molecules. The CdS/VTD-Sb2S3 interface recombination is suppressed by such properly aligned ribbons at the interface. Compared with typical [120]-oriented Sb2S3 films deposited on CdS by rapid thermal evaporation (RTE) method, the VTD-Sb2S3 thin film is highly [211]- and [121]- oriented and the performance of the solar cell is increased considerably. Without using any hole transportation layer, a conversion efficiency of 4.73% is achieved with device structure of ITO/CdS/Sb2S3/Au. This work provides a potential way to acquire vertical aligned thin films on different buffer layers.
- 1 January 2020
- Published by Wolters Kluwer Health in Critical Care Medicine
- Vol. 48 (1) , 799
1647: INFECTION SITE IMPACTS T CELL SUBSET ACCUMULATION IN SEVERE SEPSIS
- 1 January 2020
- Published by Wolters Kluwer Health in Critical Care Medicine
- Vol. 48 (1) , 799
1647: INFECTION SITE IMPACTS T CELL SUBSET ACCUMULATION IN SEVERE SEPSIS
Improvement of Cs‐(FAPbI3)0.85(MAPbBr3)0.15 Quality Via DMSO‐Molecule‐Control to Increase the Efficiency and Boost the Long‐Term Stability of 1 cm2 Sized Planar Perovskite Solar Cells
While interfacial and grain‐boundary passivation presently attract enormous research interest for perovskite solar cells (PSCs), the improvement of Cs‐(FAPbI3)X(MAPbBr3)Y bulk quality still lacks systematical study, especially for constructing polycrystalline layers in planar configurations. Here, a DMSO‐molecule‐process for improving the quality of Cs‐(FAPbI3)0.85(MAPbBr3)0.15 is developed, where the molar ratio of precursors, the kind of anti‐solvents, and speed‐time profiles are found critical. The optimized treatment significantly enhanced the crystal orientation, grain size, surface roughness, photo‐response, carrier lifetime, and contact potential difference of absorbers. Cs‐(FAPbI3)0.85(MAPbBr3)0.15 absorbers also present superior charge transport, as well as reduced carrier recombination and decreased trap densities via DMSO‐molecule‐control, enabling performance improvement on both long‐term stability and photovoltaic parameters of 1 cm2 PSCs. Champion planar cells demonstrated a power conversion efficiency (PCE) of 21.07% (0.159 cm2) and PCE of 19.4% (1 cm2) with negligible hysteresis. Moreover, 1 cm2 devices retained 90% of initial PCE after aging 50 days in ambient air.
Improvement of Cs‐(FAPbI3)0.85(MAPbBr3)0.15 Quality Via DMSO‐Molecule‐Control to Increase the Efficiency and Boost the Long‐Term Stability of 1 cm2 Sized Planar Perovskite Solar Cells
While interfacial and grain‐boundary passivation presently attract enormous research interest for perovskite solar cells (PSCs), the improvement of Cs‐(FAPbI3)X(MAPbBr3)Y bulk quality still lacks systematical study, especially for constructing polycrystalline layers in planar configurations. Here, a DMSO‐molecule‐process for improving the quality of Cs‐(FAPbI3)0.85(MAPbBr3)0.15 is developed, where the molar ratio of precursors, the kind of anti‐solvents, and speed‐time profiles are found critical. The optimized treatment significantly enhanced the crystal orientation, grain size, surface roughness, photo‐response, carrier lifetime, and contact potential difference of absorbers. Cs‐(FAPbI3)0.85(MAPbBr3)0.15 absorbers also present superior charge transport, as well as reduced carrier recombination and decreased trap densities via DMSO‐molecule‐control, enabling performance improvement on both long‐term stability and photovoltaic parameters of 1 cm2 PSCs. Champion planar cells demonstrated a power conversion efficiency (PCE) of 21.07% (0.159 cm2) and PCE of 19.4% (1 cm2) with negligible hysteresis. Moreover, 1 cm2 devices retained 90% of initial PCE after aging 50 days in ambient air.