LZLiang Zhang

Liang Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Liang Zhang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Active Balun Based Wideband Up‐Conversion Mixer With Variable Conversion Gain in 40 nm CMOS Process for Dual‐Frequency Systems

    by Liang Zhang, Yunbo Rao, Xu Cheng, Wei Su

    In this study, a highly integrated wideband double‐balanced up‐conversion mixer with digital step‐variable gain for dual‐frequency systems is proposed. Here, a 4‐bit inductorless T‐type passive attenuator is employed to showcase the attainment of a 15 dB gain control range (GCR) with 1 dB increments, and phase fluctuation is minimized by using capacitive compensation. Active baluns are employed at all intermediate frequency (IF), local oscillator (LO), and radio frequency (RF) ports to reduce size and achieve wideband performance for both IF and LO. Furthermore, two transmission paths with high isolation are incorporated for dual‐frequency systems. Fabricated in a 40 nm complementary metal‐oxide‐semiconductor process, the chip occupies a total area of 2.67 mm 2 and consumes 91.5 mW of direct current power. With an LO power level of −7 dBm, the proposed up‐mixer demonstrates a step‐variable gain ranging from 10 to 24.2 dB and from −4 to 10.2 dB in the two paths. Additionally, the high‐gain path exhibits a measured 3‐dB frequency bandwidth of 1.1–3.35 GHz with an input 1‐dB compression point (IP 1dB ) of −13 dBm, while the low‐gain path shows a measured 3‐dB frequency bandwidth of 0.7–3.05 GHz with an IP 1dB of −2 dBm. The 3‐dB IF bandwidth ranges from 0.01 to 0.8 GHz, and the measured root‐mean‐square (rms) amplitude errors are below 0.25 dB for both paths.

  • A 78–106-GHz Current-Reuse LNA With 4-dB Minimum NF and 12.5-mW Power Consumption Based on 130-nm SiGe Technology

    by Liang Zhang, Yunbo Rao, Xu Cheng, Jiangan Han, Xianhu Luo, Xianjin Deng, Binbin Cheng, Wei Su

    In this letter, a W-band broadband low-noise amplifier (LNA) with low noise figure (NF) and low power consumption is proposed based on a four-stage common-emitter (CE) topology. Noise measure (NM) is adopted as the design method to optimize the overall noise performance. The source degeneration inductor together with the slotted-metal-line-based input network is utilized to achieve the optimum NM and gain matching simultaneously. To enhance power efficiency, a zero-ohm-transmission-line (ZTL)-based current-reuse (CR) technique is employed. For verification, a wideband LNA is fabricated in 130-nm SiGe process with a chip size of 0.57 mm2. The measured results demonstrate a peak small-signal gain of 20.4 dB, a 3-dB gain bandwidth (BW) ranging from 78 to 106 GHz, a minimum NF of 4 dB, an IP1dB exceeding -19.8 dBm, and a power dissipation of 12.5 mW with a supply voltage of 2.5 V. Meanwhile, the proposed LNA exhibits an exceptionally high figure-of-merit (FoM) of 159.4 in terms of gain, BW, NF, and power consumption.


  • Compact Multifunctional 180° Hybrid-Based 300-GHz Subharmonic I/Q Downconversion Resistive Mixers in 130-nm SiGe Process

    by Liang Zhang, Fengjun Chen, Xu Cheng, Jiang-An Han, Xianhu Luo, Changxing Lin, Wei Su

    In this letter, a compact multifunctional 180° hybrid suitable for sub-harmonic I/Q mixers is proposed. To feed LO and RF signals at different frequencies and distribute DC supply, the hybrid combines an out-of-phase dual balun, two in-phase power dividers based on T-junction and coupled lines, and four zero-ohm transmission lines (ZTL) into a single passive component. Chip size, insertion loss, and bandwidth can all be improved by reducing the number of passive components cascaded in the circuit. The proposed hybrid’s footprint is further minimized by employing redundant line and compensation capacitor techniques. In a 130 nm SiGe BiCMOS technology, two proof-of-concept sub-harmonic I/Q down-conversion resistive mixers with/without an on-chip LO quadrupler are implemented. Both mixers feature wideband HBT-based IF amplifiers and emitter followers, which eliminate the need for DC-blocking capacitors that constrict the IF bandwidth. The mixer, without an integrated LO multiplier, occupies an area of 0.685×0.692 mm2 and achieves a measured conversion gain of approximately 0 dB from 255 to 310 GHz. The mixer with an on-chip LO quadrupler exhibits a conversion gain of approximately -1 dB from 270 to 300 GHz and a 3-dB IF bandwidth from 0.01 to 7 GHz. Additionally, the measured image rejection ratio (IRR) is greater than 20 dB within the operating frequencies.


  • Low-Noise Amplifiers Using 100-nm Gate Length GaN-on-Silicon Process in W-Band

    by Xiaodong Tong, Penghui Zheng, Liang Zhang

    Two low-noise amplifiers fabricated with 100-nm gate length gallium nitride (GaN)-on-silicon process in W-band are presented in this work. One has a gain of 17.5-20.5 dB in 77.5-84 GHz with 3.8-4.7-dB noise figure (NF), the other has wider bandwidth of 78.5-90 GHz with 14.5-17-dB gain and 4.5-5.2-dB NF. The chip sizes of these two low-noise amplifiers (LNAs) are 3x1.6 mm² and 3x1.4 mm² separately. The power dissipation of these two LNAs is about 190 mW. These LNAs can be integrated with high-power GaN power amplifier on the same chip, which avoids the peripheral packaging loss and achieves smaller module size. The universal gate length in commercial process with low-cost silicon substrate brings these LNAs great potential for mass production in future millimeter-wave communications.


  • A 45‐61 GHz monolithic microwave integrated circuit subharmonic mixer incorporating dual‐band power divider

    by Liang Zhang, Xiaodong Tong, Jiang‐An Han, Xu Cheng

    In this article, a novel design and realization of wideband subharmonic mixer (SHM) operating over the 45‐61 GHz frequency band is presented, in which a dual‐band power divider (DBPD), an antiparallel diode pair (APDP), and a LC low‐pass filter are employed. Working in the two corresponding frequency bands, the DBPD not only imports the RF and the LO signals, but also provides impedance transformation between the APDP, RF, and LO ports. Due to the inherent ports isolation and matching characteristics of DBPD, a simplified and miniaturized configuration of SHM has been achieved. The monolithic microwave integrated circuit (MMIC) is implemented by a GaAs 0.15 μm pHMET process with a compact chip size of 1 × 0.95 mm2 including probe pads. The mixer exhibits 14.8 to 16.5 dB conversion loss with improved return losses at the RF, LO, and IF ports. The LO‐to‐RF, LO‐to‐IF, RF‐to‐IF, 2LO‐to‐RF, and 2LO‐to‐IF isolations are 16.5 to 34.5 dB, 35 to 41.5 dB, 30 to 40 dB, 32.5 to 39.5 dB, and 50 to 61.5 dB, respectively. To the author's best knowledge, the DBPD is used in MMIC SHM design for the first time.