Elisabet Brännvall
Research Subjects
Research Interests
Elisabet Brännvall has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
Antonia Svärd
5 shared publicationsMarie Bäckström
Innventia AB, Box 5604, SE-114 86 Stockholm, Sweden
5 shared publications- Cláudia Vicente Esteves
388792 RISE Research Institutes of Sweden , Bioeconomy and Health, Pulp, Paper and Packaging , Drottning Kristinas väg 61 , Stockholm , Sweden
4 shared publications Daniel Tavast
Fibre and Polymer Technology, Royal institute of technology, KTH , Stockholm , Sweden
3 shared publications- Olena Sevastyanova
KTH Royal Institute of Technology
3 shared publications - Ulrica Edlund
Fibre and Polymer Technology, KTH Royal Institute of Technology, Teknikringen 56, SE-100 44 Stockholm, Sweden
3 shared publications
Latest Publications
- Open Access
- 4 September 2024
- Published by Springer Nature in Cellulose
- Vol. 31 (15) , 9385-9394
Effect of residual alkali level in softwood kraft cooking
The hypothesis was that low residual alkali after cooking would cause lignin re-precipitation during washing and in turn affect the subsequent oxygen delignification stage negatively. To test the hypothesis, kraft cooks were performed in lab-scale to different residual alkali levels, ranging from 5 to 15 g/L and the pulps were subjected to washing with either water or 0.1 M NaOH and then oxygen delignified. The results show that even at low residual alkali and washing with water, the pH in the liquor after washing was above 11 which is sufficiently high to keep lignin in solution. No effect of residual alkali level was observed on the performance of the oxygen delignification stage.
- 4 September 2024
- Published by Springer Nature in Cellulose
- Vol. 31 (15) , 9385-9394
Open AccessEffect of residual alkali level in softwood kraft cooking
The hypothesis was that low residual alkali after cooking would cause lignin re-precipitation during washing and in turn affect the subsequent oxygen delignification stage negatively. To test the hypothesis, kraft cooks were performed in lab-scale to different residual alkali levels, ranging from 5 to 15 g/L and the pulps were subjected to washing with either water or 0.1 M NaOH and then oxygen delignified. The results show that even at low residual alkali and washing with water, the pH in the liquor after washing was above 11 which is sufficiently high to keep lignin in solution. No effect of residual alkali level was observed on the performance of the oxygen delignification stage.
- Open Access
- 14 September 2023
- Published by Springer Nature in Cellulose
- Vol. 30 (16) , 10453-10468
Pulp delignification and refining: impact on the supramolecular structure of softwood fibers
The effect on softwood fiber wall nanostructure of kraft cooking, oxygen delignification and refining was evaluated by X-ray scattering. A recently developed simulation method for modelling small angle X-ray scattering (SAXS) data was used to estimate the apparent average sizes of solids (AAPS) and interstitial spaces in the fiber wall (AACS). Fiber saturation point and wide angle X-ray scattering were also used to calculate the pore volume in the fiber wall and the crystallite size of the fibril, respectively. The experimental modelled SAXS data was able to give consistent values for each kraft-cooked and oxygen-delignified pulp. Kraft delignification seems to have the major influence on the fiber nanostructure modification, while oxygen delignification has little or no significant impact even for different kappa numbers. The particle sizes values were more stable than the cavities sizes and no significant differences were seen between different delignification processes, refining or delignification degree. Pulps evaluated after PFI-refining, showed an increase in the fiber wall porosity evaluated by FSP and an increase in the interstitial spaces in the fiber wall, while the crystallite size and the particle sizes were very little or not affected at all.
- 14 September 2023
- Published by Springer Nature in Cellulose
- Vol. 30 (16) , 10453-10468
Open AccessPulp delignification and refining: impact on the supramolecular structure of softwood fibers
The effect on softwood fiber wall nanostructure of kraft cooking, oxygen delignification and refining was evaluated by X-ray scattering. A recently developed simulation method for modelling small angle X-ray scattering (SAXS) data was used to estimate the apparent average sizes of solids (AAPS) and interstitial spaces in the fiber wall (AACS). Fiber saturation point and wide angle X-ray scattering were also used to calculate the pore volume in the fiber wall and the crystallite size of the fibril, respectively. The experimental modelled SAXS data was able to give consistent values for each kraft-cooked and oxygen-delignified pulp. Kraft delignification seems to have the major influence on the fiber nanostructure modification, while oxygen delignification has little or no significant impact even for different kappa numbers. The particle sizes values were more stable than the cavities sizes and no significant differences were seen between different delignification processes, refining or delignification degree. Pulps evaluated after PFI-refining, showed an increase in the fiber wall porosity evaluated by FSP and an increase in the interstitial spaces in the fiber wall, while the crystallite size and the particle sizes were very little or not affected at all.
- Open Access
- 19 May 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (24) , 21474-21484
Isolation of Mixed Compositions of Cellulose Nanocrystals, Microcrystalline Cellulose, and Lignin Nanoparticles from Wood Pulps
From a circular economy perspective, one-pot strategies for the isolation of cellulose nanomaterials at a high yield and with multifunctional properties are attractive. Here, the effects of lignin content (bleached vs unbleached softwood kraft pulp) and sulfuric acid concentration on the properties of crystalline lignocellulose isolates and their films are explored. Hydrolysis at 58 wt % sulfuric acid resulted in both cellulose nanocrystals (CNCs) and microcrystalline cellulose at a relatively high yield (>55%), whereas hydrolysis at 64 wt % gave CNCs at a lower yield (<20%). CNCs from 58 wt % hydrolysis were more polydisperse and had a higher average aspect ratio (1.5-2×), a lower surface charge (2×), and a higher shear viscosity (100-1000×). Hydrolysis of unbleached pulp additionally yielded spherical nanoparticles (NPs) that were <50 nm in diameter and identified as lignin by nanoscale Fourier transform infrared spectroscopy and IR imaging. Chiral nematic self-organization was observed in films from CNCs isolated at 64 wt % but not from the more heterogeneous CNC qualities produced at 58 wt %. All films degraded to some extent under simulated sunlight trials, but these effects were less pronounced in lignin-NP-containing films, suggesting a protective feature, but the hemicellulose content and CNC crystallinity may be implicated as well. Finally, heterogeneous CNC compositions obtained at a high yield and with improved resource efficiency are suggested for specific nanocellulose uses, for instance, as thickeners or reinforcing fillers, representing a step toward the development of application-tailored CNC grades.
- 19 May 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (24) , 21474-21484
Open AccessIsolation of Mixed Compositions of Cellulose Nanocrystals, Microcrystalline Cellulose, and Lignin Nanoparticles from Wood Pulps
From a circular economy perspective, one-pot strategies for the isolation of cellulose nanomaterials at a high yield and with multifunctional properties are attractive. Here, the effects of lignin content (bleached vs unbleached softwood kraft pulp) and sulfuric acid concentration on the properties of crystalline lignocellulose isolates and their films are explored. Hydrolysis at 58 wt % sulfuric acid resulted in both cellulose nanocrystals (CNCs) and microcrystalline cellulose at a relatively high yield (>55%), whereas hydrolysis at 64 wt % gave CNCs at a lower yield (<20%). CNCs from 58 wt % hydrolysis were more polydisperse and had a higher average aspect ratio (1.5-2×), a lower surface charge (2×), and a higher shear viscosity (100-1000×). Hydrolysis of unbleached pulp additionally yielded spherical nanoparticles (NPs) that were <50 nm in diameter and identified as lignin by nanoscale Fourier transform infrared spectroscopy and IR imaging. Chiral nematic self-organization was observed in films from CNCs isolated at 64 wt % but not from the more heterogeneous CNC qualities produced at 58 wt %. All films degraded to some extent under simulated sunlight trials, but these effects were less pronounced in lignin-NP-containing films, suggesting a protective feature, but the hemicellulose content and CNC crystallinity may be implicated as well. Finally, heterogeneous CNC compositions obtained at a high yield and with improved resource efficiency are suggested for specific nanocellulose uses, for instance, as thickeners or reinforcing fillers, representing a step toward the development of application-tailored CNC grades.
- Open Access
Carbon Fibers from Wet-Spun Cellulose-Lignin Precursors Using the Cold Alkali Process
In recent years, there has been extensive research into the development of cheaper and more sustainable carbon fiber (CF) precursors, and air-gap-spun cellulose-lignin precursors have gained considerable attention where ionic liquids have been used for the co-dissolution of cellulose and lignin. However, ionic liquids are expensive and difficult to recycle. In the present work, an aqueous solvent system, cold alkali, was used to prepare cellulose-lignin CF precursors by wet spinning solutions containing co-dissolved dissolving-grade kraft pulp and softwood kraft lignin. Precursors containing up to 30 wt% lignin were successfully spun using two different coagulation bath compositions, where one of them introduced a flame retardant into the precursor to increase the CF conversion yield. The precursors were converted to CFs via batchwise and continuous conversion. The precursor and conversion conditions had a significant effect on the conversion yield (12–44 wt%), the Young’s modulus (33–77 GPa), and the tensile strength (0.48–1.17 GPa), while the precursor morphology was preserved. Structural characterization of the precursors and CFs showed that a more oriented and crystalline precursor gave a more ordered CF structure with higher tensile properties. The continuous conversion trials highlighted the importance of tension control to increase the mechanical properties of the CFs.
Open AccessCarbon Fibers from Wet-Spun Cellulose-Lignin Precursors Using the Cold Alkali Process
In recent years, there has been extensive research into the development of cheaper and more sustainable carbon fiber (CF) precursors, and air-gap-spun cellulose-lignin precursors have gained considerable attention where ionic liquids have been used for the co-dissolution of cellulose and lignin. However, ionic liquids are expensive and difficult to recycle. In the present work, an aqueous solvent system, cold alkali, was used to prepare cellulose-lignin CF precursors by wet spinning solutions containing co-dissolved dissolving-grade kraft pulp and softwood kraft lignin. Precursors containing up to 30 wt% lignin were successfully spun using two different coagulation bath compositions, where one of them introduced a flame retardant into the precursor to increase the CF conversion yield. The precursors were converted to CFs via batchwise and continuous conversion. The precursor and conversion conditions had a significant effect on the conversion yield (12–44 wt%), the Young’s modulus (33–77 GPa), and the tensile strength (0.48–1.17 GPa), while the precursor morphology was preserved. Structural characterization of the precursors and CFs showed that a more oriented and crystalline precursor gave a more ordered CF structure with higher tensile properties. The continuous conversion trials highlighted the importance of tension control to increase the mechanical properties of the CFs.
- Open Access
- 21 September 2022
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 37 (4) , 593-608
The impact of bleaching on the yield of softwood kraft pulps obtained by high alkali impregnation
High alkali impregnation (HAI) increases the total yield of softwood pulps following kraft cooking. This yield improvement is also maintained after oxygen delignification. This study evaluates how bleaching with either chlorine dioxide or hydrogen peroxide affects the final yield of samples obtained with standard and HAI. The chemical composition, viscosity, brightness, mechanical and morphological properties were studied. Compared to cooking after standard impregnation the yield improvement achieved by HAI was preserved in both types of bleaching sequences (2 % units for chlorine dioxide and 4 % units for hydrogen peroxide). The introduction of charged groups into the cellulose fibers was higher with hydrogen peroxide bleaching than with chlorine dioxide however, no significant impact was seen on the swelling or mechanical properties. The brightness was higher for the pulps bleached with chlorine dioxide compared with hydrogen peroxide. Hydrogen peroxide bleaching resulted in similar brightness development for both standard and HAI. Fibers bleached with chlorine dioxide had the highest curl index (16–17 %) compared to the fibers bleached with hydrogen peroxide (15 %).
- 21 September 2022
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 37 (4) , 593-608
Open AccessThe impact of bleaching on the yield of softwood kraft pulps obtained by high alkali impregnation
High alkali impregnation (HAI) increases the total yield of softwood pulps following kraft cooking. This yield improvement is also maintained after oxygen delignification. This study evaluates how bleaching with either chlorine dioxide or hydrogen peroxide affects the final yield of samples obtained with standard and HAI. The chemical composition, viscosity, brightness, mechanical and morphological properties were studied. Compared to cooking after standard impregnation the yield improvement achieved by HAI was preserved in both types of bleaching sequences (2 % units for chlorine dioxide and 4 % units for hydrogen peroxide). The introduction of charged groups into the cellulose fibers was higher with hydrogen peroxide bleaching than with chlorine dioxide however, no significant impact was seen on the swelling or mechanical properties. The brightness was higher for the pulps bleached with chlorine dioxide compared with hydrogen peroxide. Hydrogen peroxide bleaching resulted in similar brightness development for both standard and HAI. Fibers bleached with chlorine dioxide had the highest curl index (16–17 %) compared to the fibers bleached with hydrogen peroxide (15 %).
- Open Access
- 10 May 2022
- Published by Springer Nature in Cellulose
- Vol. 29 (9) , 4961-4976
CNFs from softwood pulp fibers containing hemicellulose and lignin
The energy demand to produce cellulose nanofibrils, CNFs, is high and additionally the cost of the starting material, the pulp, is substantial as high purity cellulose dissolving pulp is generally used. Pulps aimed for board and paper are produced at higher yield as they contain hemicelluloses and, in the case of unbleached pulp, lignin, and would be a more economical starting material for CNFs. It is of interest to understand how the presence of hemicellulose and lignin affects the fibrillation process and CNF properties. Kraft cooks of softwood were performed as well as kraft cooks with addition of polysulfide to increase the hemicellulose content. Part of the pulps were bleached to remove residual lignin, thus making it possible to compare pulps with and without lignin. Higher amount of hemicellulose had an obstructive effect on the enzymatic pre-treatment whereas lignin had no adverse effect on enzyme accessibility. Increased amount of charged groups improved the accessibility for enzymes. Both hemicellulose and lignin were carboxymethylated when pre-treatment by carboxymethylation was employed. However, carboxymethylation partly dissolved hemicelluloses. The tensile strength of CNF films was independent of the chemical composition of the pulp and the pre-treatment strategy. However, since the enzymatic pre-treatment decreased the cellulose DP more, CNF films from enzymatically pre-treated pulps had generally lower tensile strength.
- 10 May 2022
- Published by Springer Nature in Cellulose
- Vol. 29 (9) , 4961-4976
Open AccessCNFs from softwood pulp fibers containing hemicellulose and lignin
The energy demand to produce cellulose nanofibrils, CNFs, is high and additionally the cost of the starting material, the pulp, is substantial as high purity cellulose dissolving pulp is generally used. Pulps aimed for board and paper are produced at higher yield as they contain hemicelluloses and, in the case of unbleached pulp, lignin, and would be a more economical starting material for CNFs. It is of interest to understand how the presence of hemicellulose and lignin affects the fibrillation process and CNF properties. Kraft cooks of softwood were performed as well as kraft cooks with addition of polysulfide to increase the hemicellulose content. Part of the pulps were bleached to remove residual lignin, thus making it possible to compare pulps with and without lignin. Higher amount of hemicellulose had an obstructive effect on the enzymatic pre-treatment whereas lignin had no adverse effect on enzyme accessibility. Increased amount of charged groups improved the accessibility for enzymes. Both hemicellulose and lignin were carboxymethylated when pre-treatment by carboxymethylation was employed. However, carboxymethylation partly dissolved hemicelluloses. The tensile strength of CNF films was independent of the chemical composition of the pulp and the pre-treatment strategy. However, since the enzymatic pre-treatment decreased the cellulose DP more, CNF films from enzymatically pre-treated pulps had generally lower tensile strength.
- Open Access
- 5 May 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (19) , 16793-16802
Continuous Stabilization and Carbonization of a Lignin–Cellulose Precursor to Carbon Fiber
The demand for carbon fibers (CFs) based on renewable raw materials as the reinforcing fiber in composites for lightweight applications is growing. Lignin-cellulose precursor fibers (PFs) are a promising alternative, but so far, there is limited knowledge of how to continuously convert these PFs under industrial-like conditions into CFs. Continuous conversion is vital for the industrial production of CFs. In this work, we have compared the continuous conversion of lignin-cellulose PFs (50 wt % softwood kraft lignin and 50 wt % dissolving-grade kraft pulp) with batchwise conversion. The PFs were successfully stabilized and carbonized continuously over a total time of 1.0-1.5 h, comparable to the industrial production of CFs from polyacrylonitrile. CFs derived continuously at 1000 °C with a relative stretch of -10% (fiber contraction) had a conversion yield of 29 wt %, a diameter of 12-15 μm, a Young's modulus of 46-51 GPa, and a tensile strength of 710-920 MPa. In comparison, CFs obtained at 1000 °C via batchwise conversion (12-15 μm diameter) with a relative stretch of 0% and a conversion time of 7 h (due to the low heating and cooling rates) had a higher conversion yield of 34 wt %, a higher Young's modulus (63-67 GPa) but a similar tensile strength (800-920 MPa). This suggests that the Young's modulus can be improved by the optimization of the fiber tension, residence time, and temperature profile during continuous conversion, while a higher tensile strength can be achieved by reducing the fiber diameter as it minimizes the risk of critical defects.
- 5 May 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (19) , 16793-16802
Open AccessContinuous Stabilization and Carbonization of a Lignin–Cellulose Precursor to Carbon Fiber
The demand for carbon fibers (CFs) based on renewable raw materials as the reinforcing fiber in composites for lightweight applications is growing. Lignin-cellulose precursor fibers (PFs) are a promising alternative, but so far, there is limited knowledge of how to continuously convert these PFs under industrial-like conditions into CFs. Continuous conversion is vital for the industrial production of CFs. In this work, we have compared the continuous conversion of lignin-cellulose PFs (50 wt % softwood kraft lignin and 50 wt % dissolving-grade kraft pulp) with batchwise conversion. The PFs were successfully stabilized and carbonized continuously over a total time of 1.0-1.5 h, comparable to the industrial production of CFs from polyacrylonitrile. CFs derived continuously at 1000 °C with a relative stretch of -10% (fiber contraction) had a conversion yield of 29 wt %, a diameter of 12-15 μm, a Young's modulus of 46-51 GPa, and a tensile strength of 710-920 MPa. In comparison, CFs obtained at 1000 °C via batchwise conversion (12-15 μm diameter) with a relative stretch of 0% and a conversion time of 7 h (due to the low heating and cooling rates) had a higher conversion yield of 34 wt %, a higher Young's modulus (63-67 GPa) but a similar tensile strength (800-920 MPa). This suggests that the Young's modulus can be improved by the optimization of the fiber tension, residence time, and temperature profile during continuous conversion, while a higher tensile strength can be achieved by reducing the fiber diameter as it minimizes the risk of critical defects.
- Open Access
- 28 February 2022
- Published by Springer Nature in Research Square
Effect of Residual Alkali Level in Softwood Kraft Cooking
In washing of softwood pulp, pH is reduced to such low levels that re-precipitation of dissolved lignin may result. It was hypothesized that the lower the residual alkali after cooking, the higher the risk of lignin re-precipitation, which in turn would affect the subsequent oxygen delignification stage negatively. To test the hypothesis, kraft cooks were performed to different residual alkali levels, ranging from 5 to 15 g/l and the delignified chips were subjected to different washing strategies and then oxygen delignified. However, the results show that even at low residual alkali, lignin stays in solution and only minor amounts of lignin re-precipitate during washing. The amount was irrespective of the residual alkali level in the cook and amounted to 1-2 kappa number units. No effect of residual alkali level was observed on the performance of the oxygen delignification stage. The residual alkali level affected the lignin concentration in the lumen after cooking. At the low residual alkali level, the lignin concentration in the lumen liquor was equal to the free liquor and as the residual alkali level increased, the lignin concentration in the lumen increased, while the lignin concentration in the free black liquor remained on the same level at all residual alkali levels.
- 28 February 2022
- Published by Springer Nature in Research Square
Open AccessEffect of Residual Alkali Level in Softwood Kraft Cooking
In washing of softwood pulp, pH is reduced to such low levels that re-precipitation of dissolved lignin may result. It was hypothesized that the lower the residual alkali after cooking, the higher the risk of lignin re-precipitation, which in turn would affect the subsequent oxygen delignification stage negatively. To test the hypothesis, kraft cooks were performed to different residual alkali levels, ranging from 5 to 15 g/l and the delignified chips were subjected to different washing strategies and then oxygen delignified. However, the results show that even at low residual alkali, lignin stays in solution and only minor amounts of lignin re-precipitate during washing. The amount was irrespective of the residual alkali level in the cook and amounted to 1-2 kappa number units. No effect of residual alkali level was observed on the performance of the oxygen delignification stage. The residual alkali level affected the lignin concentration in the lumen after cooking. At the low residual alkali level, the lignin concentration in the lumen liquor was equal to the free liquor and as the residual alkali level increased, the lignin concentration in the lumen increased, while the lignin concentration in the free black liquor remained on the same level at all residual alkali levels.
- Open Access
- 9 March 2021
- Published by Springer Nature in Cellulose
- Vol. 28 (7) , 3951-3965
Changes in the cellulose fiber wall supramolecular structure during the initial stages of chemical treatments of wood evaluated by NMR and X-ray scattering
The effect of initial stages of pulping of spruce, resembling prehydrolysis and alkaline cooking was studied using CP/MAS 13C-NMR, X-ray scattering, FSP and carbohydrate composition in order to study the impact of the pre-treatments on the fiber wall nanostructure. Removal of fiber wall components, hemicellulose and lignin, increased the fiber wall porosity and induced cellulose fibril aggregation. The effect of temperature and pH in the treatment on cellulose fibril aggregate size appears to be secondary. It is the removal of hemicellulose that has a profound effect on the supramolecular structure of the cellulose fiber wall. As the amount of hemicellulose dissolved from wood increases, the fibril aggregate size determined by NMR increases as well, ranging from 16 to 28 nm. Specifically, a good correlation between the amount of glucomannan in the fiber wall and the fibril aggregate size is seen. The lower the amount of glucomannan, the larger the aggregate size. Glucomannan thus seems to prevent aggregation as it acts as a very efficient spacer between fibrils. Elemental fibril size determined by NMR, was quite similar for all samples, ranging from 3.6 to 4.1 nm. By combining measurement methods, a more well-resolved picture of the structural changes occurring during was obtained.
- 9 March 2021
- Published by Springer Nature in Cellulose
- Vol. 28 (7) , 3951-3965
Open AccessChanges in the cellulose fiber wall supramolecular structure during the initial stages of chemical treatments of wood evaluated by NMR and X-ray scattering
The effect of initial stages of pulping of spruce, resembling prehydrolysis and alkaline cooking was studied using CP/MAS 13C-NMR, X-ray scattering, FSP and carbohydrate composition in order to study the impact of the pre-treatments on the fiber wall nanostructure. Removal of fiber wall components, hemicellulose and lignin, increased the fiber wall porosity and induced cellulose fibril aggregation. The effect of temperature and pH in the treatment on cellulose fibril aggregate size appears to be secondary. It is the removal of hemicellulose that has a profound effect on the supramolecular structure of the cellulose fiber wall. As the amount of hemicellulose dissolved from wood increases, the fibril aggregate size determined by NMR increases as well, ranging from 16 to 28 nm. Specifically, a good correlation between the amount of glucomannan in the fiber wall and the fibril aggregate size is seen. The lower the amount of glucomannan, the larger the aggregate size. Glucomannan thus seems to prevent aggregation as it acts as a very efficient spacer between fibrils. Elemental fibril size determined by NMR, was quite similar for all samples, ranging from 3.6 to 4.1 nm. By combining measurement methods, a more well-resolved picture of the structural changes occurring during was obtained.
- Open Access
- 27 February 2021
- Published by Springer Nature in Cellulose
- Vol. 28 (6) , 3775-3788
Differences and similarities between kraft and oxygen delignification of softwood fibers: effects on mechanical properties
Charged groups in pulp have been shown to enhance the tensile strength of the paper produced from the pulp. Oxygen delignification introduces charged groups and it is of interest to determine how the delignification should be distributed between the cooking and the oxygen stage with respect to mechanical properties. A number of unbleached kraft cooked and oxygen delignified pulps within a wide kappa number range were produced and refined, and the effects of the refining on the morphology and mechanical properties were studied. The WRV correlated with the fiber charge and at a given fiber charge, kraft cooked and oxygen delignified pulps had the same WRV development in refining, although they had significantly different kappa numbers. The tensile strength development during refining depends on the fiber rigidity which is affected by the lignin content, the fiber charge and the chemical and mechanical processes used. Refining increased the curl of the kraft cooked pulps and decreased the curl of oxygen delignified pulps, irrespective of kappa number. A greater increase in tensile strength was seen for the pulps with a higher fiber charge and WRV, probably because of the greater degree of fibrillation achieved in the beating process. Despite the greater fiber deformation in the oxygen delignified pulps, the strength can be increased by a larger amount of charged groups and a greater swelling of the fibers.Graphic abstract
- 27 February 2021
- Published by Springer Nature in Cellulose
- Vol. 28 (6) , 3775-3788
Open AccessDifferences and similarities between kraft and oxygen delignification of softwood fibers: effects on mechanical properties
Charged groups in pulp have been shown to enhance the tensile strength of the paper produced from the pulp. Oxygen delignification introduces charged groups and it is of interest to determine how the delignification should be distributed between the cooking and the oxygen stage with respect to mechanical properties. A number of unbleached kraft cooked and oxygen delignified pulps within a wide kappa number range were produced and refined, and the effects of the refining on the morphology and mechanical properties were studied. The WRV correlated with the fiber charge and at a given fiber charge, kraft cooked and oxygen delignified pulps had the same WRV development in refining, although they had significantly different kappa numbers. The tensile strength development during refining depends on the fiber rigidity which is affected by the lignin content, the fiber charge and the chemical and mechanical processes used. Refining increased the curl of the kraft cooked pulps and decreased the curl of oxygen delignified pulps, irrespective of kappa number. A greater increase in tensile strength was seen for the pulps with a higher fiber charge and WRV, probably because of the greater degree of fibrillation achieved in the beating process. Despite the greater fiber deformation in the oxygen delignified pulps, the strength can be increased by a larger amount of charged groups and a greater swelling of the fibers.Graphic abstract