Sina Ghaemi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sina Ghaemi has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Bradley Gibeau
11 shared publicationsSen Wang
Univ Alberta, Dept Mech Engn, Edmonton, AB, Canada
6 shared publications- Lucas Warwaruk
Massachusetts Institute of Technology 77 Massachusetts Avenue
4 shared publications - Wagih Abu Rowin
Department of Mechanical Engineering, University of Melbourne, Parkville, Australia
4 shared publications Findlay McCormick
Univ Alberta, Dept Mech Engn, Edmonton, AB, Canada
2 shared publications- Prashant Das
Department of Mechanical Engineering, Indian Institute of Science, Bangalore, 560012, India
2 shared publications
Latest Publications
- 5 October 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- p. 1-14
Evaluating Aerodynamic and Propulsive Performance of a Wing with Distributed Electric Propulsion
Distributed electric propulsion (DEP) has gained significant attention for its potential to enhance aerodynamic and propulsive performance by leveraging the interaction between several propellers and the aircraft wing. To identify suitable DEP configurations and operating conditions, a wind tunnel investigation was conducted using an eight-propeller DEP system and a three-dimensional wing at a chord-based Reynolds number of 350,000. Aerodynamic load measurements were obtained using a six-axis load cell for the wing and single-axis load cells for each propeller. The DEP system was placed in several tractor, pusher, and over-the-wing (OTW) configurations. The thrust of each propeller was maintained at specific values while propeller advance ratios were varied. The results demonstrated that the tractor and OTW configurations augmented lift by as much as 32% and 26%, respectively, while a simultaneous increase in propeller efficiency was only observed in the tractor configuration. Moreover, lift augmentation was further enhanced using a nonuniform thrust distribution where more thrust was allocated near the wing root. Regarding overall efficiency, a tractor configuration with propellers below the leading edge and an OTW configuration near 30% of the airfoil chord had the highest efficiency when operating at cruise and higher thrust, respectively.
- 5 October 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- p. 1-14
Evaluating Aerodynamic and Propulsive Performance of a Wing with Distributed Electric Propulsion
Distributed electric propulsion (DEP) has gained significant attention for its potential to enhance aerodynamic and propulsive performance by leveraging the interaction between several propellers and the aircraft wing. To identify suitable DEP configurations and operating conditions, a wind tunnel investigation was conducted using an eight-propeller DEP system and a three-dimensional wing at a chord-based Reynolds number of 350,000. Aerodynamic load measurements were obtained using a six-axis load cell for the wing and single-axis load cells for each propeller. The DEP system was placed in several tractor, pusher, and over-the-wing (OTW) configurations. The thrust of each propeller was maintained at specific values while propeller advance ratios were varied. The results demonstrated that the tractor and OTW configurations augmented lift by as much as 32% and 26%, respectively, while a simultaneous increase in propeller efficiency was only observed in the tractor configuration. Moreover, lift augmentation was further enhanced using a nonuniform thrust distribution where more thrust was allocated near the wing root. Regarding overall efficiency, a tractor configuration with propellers below the leading edge and an OTW configuration near 30% of the airfoil chord had the highest efficiency when operating at cruise and higher thrust, respectively.
- Open Access
- 25 July 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1016, A1
Estimating the skin-friction coefficient in drag-reduced pipe flows of a flexible polymer
In turbulent pipe flows, drag-reducing polymers are commonly used to reduce skin-friction drag; however, predicting this reduction in industry applications, such as crude oil pipelines, remains challenging. The skin-friction coefficient ( $C_f$ ) of polymer drag-reduced turbulent pipe flows can be related to three dimensionless parameters: the solvent Reynolds number ( $Re_s$ ), the Weissenberg number ( $Wi$ ) and the ratio of solvent viscosity ( $\eta _s$ ) to zero-shear-rate viscosity ( $\eta _0$ ), denoted as $\beta$ . The function that relates these four dimensionless numbers was determined using experiments of various pipe diameters ( $D$ ), flow velocities ( $U$ ) and drag-reducing polyacrylamide solutions. The experiments included measurements of streamwise pressure drop ( $\Delta P$ ) for determining $C_f$ , and measurements of shear viscosity ( $\eta$ ) and elastic relaxation time ( $\lambda$ ). This experimental campaign involved 156 flow conditions, each characterised by distinct values for $C_f$ , $Re_s$ , $Wi$ and $\beta$ . Experimental results demonstrated good agreement with the relationship: $C_f^{-1/2} = \widehat {A}\log _{10}(Re_sC_f^{1/2})+\widehat {B}$ , where $\widehat {A} = 27.6(Wi \beta )^{0.346}$ and $\widehat {B} = 122/15-58.9(Wi \beta )^{0.346}$ . Based on this relationship, onset and maximum drag reduction are predicted to occur when $Wi \beta$ equals $3.76 \times 10^{-3}$ and $3.40 \times 10^{-1}$ , respectively. This function can predict $C_f$ of dilute polyacrylamide solutions based on predefined parameters (bulk velocity, pipe diameter, density, solvent viscosity) and two measurable rheological properties of the solution (shear viscosity and elastic relaxation time) with an accuracy of $\pm 9.36$ %.- 25 July 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1016, A1
Open AccessEstimating the skin-friction coefficient in drag-reduced pipe flows of a flexible polymer
In turbulent pipe flows, drag-reducing polymers are commonly used to reduce skin-friction drag; however, predicting this reduction in industry applications, such as crude oil pipelines, remains challenging. The skin-friction coefficient ( $C_f$ ) of polymer drag-reduced turbulent pipe flows can be related to three dimensionless parameters: the solvent Reynolds number ( $Re_s$ ), the Weissenberg number ( $Wi$ ) and the ratio of solvent viscosity ( $\eta _s$ ) to zero-shear-rate viscosity ( $\eta _0$ ), denoted as $\beta$ . The function that relates these four dimensionless numbers was determined using experiments of various pipe diameters ( $D$ ), flow velocities ( $U$ ) and drag-reducing polyacrylamide solutions. The experiments included measurements of streamwise pressure drop ( $\Delta P$ ) for determining $C_f$ , and measurements of shear viscosity ( $\eta$ ) and elastic relaxation time ( $\lambda$ ). This experimental campaign involved 156 flow conditions, each characterised by distinct values for $C_f$ , $Re_s$ , $Wi$ and $\beta$ . Experimental results demonstrated good agreement with the relationship: $C_f^{-1/2} = \widehat {A}\log _{10}(Re_sC_f^{1/2})+\widehat {B}$ , where $\widehat {A} = 27.6(Wi \beta )^{0.346}$ and $\widehat {B} = 122/15-58.9(Wi \beta )^{0.346}$ . Based on this relationship, onset and maximum drag reduction are predicted to occur when $Wi \beta$ equals $3.76 \times 10^{-3}$ and $3.40 \times 10^{-1}$ , respectively. This function can predict $C_f$ of dilute polyacrylamide solutions based on predefined parameters (bulk velocity, pipe diameter, density, solvent viscosity) and two measurable rheological properties of the solution (shear viscosity and elastic relaxation time) with an accuracy of $\pm 9.36$ %. - 23 April 2025
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 168
Measurements of the vortex structure in the wake of a scale helicopter rotor in forward motion
- 23 April 2025
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 168
Measurements of the vortex structure in the wake of a scale helicopter rotor in forward motion
- Open Access
- 5 August 2024
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 159
Experimental evaluation of the flow field induced by an active vortex generator
- 5 August 2024
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 159
Open AccessExperimental evaluation of the flow field induced by an active vortex generator
- 14 June 2024
- Published by Springer Nature in Experiments in Fluids
- Vol. 65 (7) , 1-20
The interaction between turbulent separation bubble breathing and wall pressure on a 2D wing
- 14 June 2024
- Published by Springer Nature in Experiments in Fluids
- Vol. 65 (7) , 1-20
The interaction between turbulent separation bubble breathing and wall pressure on a 2D wing
- Open Access
- 19 April 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 985, A19
Spectral proper orthogonal decomposition of time-resolved three-dimensional flow measurements in the turbulent wake of the Ahmed body
This study investigated the turbulent wake flow behind a flat-back Ahmed body using a combination of time-resolved tomographic particle image velocimetry measurements and spectral proper orthogonal decomposition (SPOD). The experiments were conducted at a Reynolds number of ReH = 10 000, which is defined as U∞H/ν, where U∞ represents the free-stream velocity, H is the height of the body and ν represents the viscosity. The SPOD analysis revealed four distinct flow motions present in the wake of the Ahmed body, each occupying a specific range of Strouhal number, StH. Here, StH is defined as f × H/U∞, where f is the frequency of the motion. At the lowest resolved StH of 0.007, the system exhibited a bi-stability mode, in which the wake switched between asymmetric states consisting of a tilted toroidal vortex and a streamwise vortex. In the next StH range of 0.014 to 0.123, the flow demonstrated swinging/flapping motions, characterized by small spanwise and vertical movements of the wake barycentre. These movements were attributed to the tilting of the toroidal vortex. The third category included the vortex-shedding motions and consisted of quasi-streamwise vortices. These vortices advected in the downstream direction, causing oblique displacements of the barycentre in the streamwise-vertical plane. The peak energy of the vortex shedding was observed at StH = 0.164. Finally, shear layer instabilities induced small vertical and spanwise velocity fluctuations along the shear layers at a high StH of 1.147.
- 19 April 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 985, A19
Open AccessSpectral proper orthogonal decomposition of time-resolved three-dimensional flow measurements in the turbulent wake of the Ahmed body
This study investigated the turbulent wake flow behind a flat-back Ahmed body using a combination of time-resolved tomographic particle image velocimetry measurements and spectral proper orthogonal decomposition (SPOD). The experiments were conducted at a Reynolds number of ReH = 10 000, which is defined as U∞H/ν, where U∞ represents the free-stream velocity, H is the height of the body and ν represents the viscosity. The SPOD analysis revealed four distinct flow motions present in the wake of the Ahmed body, each occupying a specific range of Strouhal number, StH. Here, StH is defined as f × H/U∞, where f is the frequency of the motion. At the lowest resolved StH of 0.007, the system exhibited a bi-stability mode, in which the wake switched between asymmetric states consisting of a tilted toroidal vortex and a streamwise vortex. In the next StH range of 0.014 to 0.123, the flow demonstrated swinging/flapping motions, characterized by small spanwise and vertical movements of the wake barycentre. These movements were attributed to the tilting of the toroidal vortex. The third category included the vortex-shedding motions and consisted of quasi-streamwise vortices. These vortices advected in the downstream direction, causing oblique displacements of the barycentre in the streamwise-vertical plane. The peak energy of the vortex shedding was observed at StH = 0.164. Finally, shear layer instabilities induced small vertical and spanwise velocity fluctuations along the shear layers at a high StH of 1.147.
- Open Access
- 16 April 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 985, A9
Reactive control of velocity fluctuations using an active deformable surface and real-time PIV
This study demonstrates an experimental realization of turbulence control strategies previously explored by Choiet al.(J. Fluid Mech., vol. 262, 1994, pp. 75–110) through numerical simulations. To conduct the experiments, a deformable surface with a streamwise array of 16 independently controlled actuators was developed. A real-time particle image velocimetry (RT-PIV) system was also created for flow measurements. The objective of the control strategy was to target the sweep and ejection motions of the vortex shedding from a spherical cap placed in a laminar boundary layer. Reactive control strategies consisted of wall-normal surface deformations that opposed or complied with the wall-normal (v) or streamwise (u) velocity fluctuations obtained from the RT-PIV. The results showed two primary outcomes of the control approach. Firstly, it effectively hindered the advancement of sweep motions towards the wall. Secondly, it disrupted the periodic shedding of vortices. Thev-control with opposing wall motions andu-control with compliant wall motions exhibited strong inhibition of sweep motions, while thev-control with compliant andu-control with opposing wall motions showed weaker inhibition. All reactive control cases resulted in the disruption of vortex shedding. In some instances, this disruption was accompanied by increased turbulent kinetic energy due to the generation of additional flow motions. However, thev-control with opposing wall motions significantly reduced the vortex-shedding energy while maintaining total turbulent kinetic energy close to or below that of the unforced flow. Overall, the experiments show the effectiveness of reactive control strategies in mitigating sweep motions and disrupting vortical structures, offering insights for developing reactive control strategies.
- 16 April 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 985, A9
Open AccessReactive control of velocity fluctuations using an active deformable surface and real-time PIV
This study demonstrates an experimental realization of turbulence control strategies previously explored by Choiet al.(J. Fluid Mech., vol. 262, 1994, pp. 75–110) through numerical simulations. To conduct the experiments, a deformable surface with a streamwise array of 16 independently controlled actuators was developed. A real-time particle image velocimetry (RT-PIV) system was also created for flow measurements. The objective of the control strategy was to target the sweep and ejection motions of the vortex shedding from a spherical cap placed in a laminar boundary layer. Reactive control strategies consisted of wall-normal surface deformations that opposed or complied with the wall-normal (v) or streamwise (u) velocity fluctuations obtained from the RT-PIV. The results showed two primary outcomes of the control approach. Firstly, it effectively hindered the advancement of sweep motions towards the wall. Secondly, it disrupted the periodic shedding of vortices. Thev-control with opposing wall motions andu-control with compliant wall motions exhibited strong inhibition of sweep motions, while thev-control with compliant andu-control with opposing wall motions showed weaker inhibition. All reactive control cases resulted in the disruption of vortex shedding. In some instances, this disruption was accompanied by increased turbulent kinetic energy due to the generation of additional flow motions. However, thev-control with opposing wall motions significantly reduced the vortex-shedding energy while maintaining total turbulent kinetic energy close to or below that of the unforced flow. Overall, the experiments show the effectiveness of reactive control strategies in mitigating sweep motions and disrupting vortical structures, offering insights for developing reactive control strategies.
- Open Access
- 18 March 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 983, A22
Local flow topology of a polymer-laden turbulent boundary layer
Fine-scale flow motions are measured in a Newtonian and polymer drag-reduced turbulent boundary layer (TBL) at a common momentum thickness Reynolds number $Re_{\theta }$ of 2300. Relative to the Newtonian TBL, the polymer-laden flow has a 33 % lower skin-friction coefficient. Three-dimensional (3-D) particle tracking velocimetry is used to measure the components of the velocity gradient tensor (VGT), rate of deformation tensor (RDT) and rate of rotation tensor (RRT). The invariants in these tensors are then used to distinguish the different types of fine-scale flow motions – a method called the $\varDelta$ -criterion. Joint probability density functions (j.p.d.f.s) of the VGT invariants, $Q$ and $R$ , for the Newtonian TBL produce the familiar tear-drop pattern, commonly seen in direct numerical simulations of Newtonian turbulence. Relative to the Newtonian TBL, the polymer-laden flow has significantly attenuated values of $R$ , implying an overall reduction in fluid stretching. The invariants in the RDT, $Q_D$ and $R_D$ , imply that straining motions of the polymeric flow are more two dimensional compared with the Newtonian flow. Moreover, j.p.d.f.s of $Q_D$ and the invariant in the RRT $Q_W$ , suggest that the flow consists of fewer biaxial extensional events and more shear-dominated flow. Few, if any, experimental investigations have measured the 3-D structure of fine-scale motions in a Newtonian and polymer drag-reduced TBL using the $\varDelta$ -criterion. We provide the first experimental evidence that supports the notion that an attenuation of fluid stretching, particularly biaxial straining motions, is central to the mechanism of polymer drag reduction.- 18 March 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 983, A22
Open AccessLocal flow topology of a polymer-laden turbulent boundary layer
Fine-scale flow motions are measured in a Newtonian and polymer drag-reduced turbulent boundary layer (TBL) at a common momentum thickness Reynolds number $Re_{\theta }$ of 2300. Relative to the Newtonian TBL, the polymer-laden flow has a 33 % lower skin-friction coefficient. Three-dimensional (3-D) particle tracking velocimetry is used to measure the components of the velocity gradient tensor (VGT), rate of deformation tensor (RDT) and rate of rotation tensor (RRT). The invariants in these tensors are then used to distinguish the different types of fine-scale flow motions – a method called the $\varDelta$ -criterion. Joint probability density functions (j.p.d.f.s) of the VGT invariants, $Q$ and $R$ , for the Newtonian TBL produce the familiar tear-drop pattern, commonly seen in direct numerical simulations of Newtonian turbulence. Relative to the Newtonian TBL, the polymer-laden flow has significantly attenuated values of $R$ , implying an overall reduction in fluid stretching. The invariants in the RDT, $Q_D$ and $R_D$ , imply that straining motions of the polymeric flow are more two dimensional compared with the Newtonian flow. Moreover, j.p.d.f.s of $Q_D$ and the invariant in the RRT $Q_W$ , suggest that the flow consists of fewer biaxial extensional events and more shear-dominated flow. Few, if any, experimental investigations have measured the 3-D structure of fine-scale motions in a Newtonian and polymer drag-reduced TBL using the $\varDelta$ -criterion. We provide the first experimental evidence that supports the notion that an attenuation of fluid stretching, particularly biaxial straining motions, is central to the mechanism of polymer drag reduction. - 1 February 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (6)
Comparison of Heat Transfer and Friction in Pipes With Various Internal Roughness
The heat transfer and friction factor of turbulent pipe flows with different internal roughness are experimentally investigated. Three types of roughness in forms of a mesh, hemispherical elements, and a coil are added to the interior of pipes with an inner diameter of 52.5 mm. The working fluid is air, and the Reynolds numbers vary from 20,000 to 90,000 in increments of 10,000. For investigating the heat transfer, the pipe wall is heated to 375 °C while the inlet air remains at the room temperature. The measurements show that the mesh-type roughness results in a maximum Nusselt number, Nu, increase of approximately 6%, the pipes with hemispherical roughness increased the Nu by a maximum amount of 30%, and the coil increased Nu by up to 60% compared with the smooth pipe. The maximum increase of friction factor is 40% for the pipes with mesh-type roughness, 30% for pipes with hemispherical roughness, and 67% for pipes with coil roughness. The experimental results indicate that adding hemispherical and coil roughness to the internal surface of the pipe can lead to a significant improvement in the rate of heat transfer while adding a mesh-type roughness can have marginal improvements and comes with a large frictional loss penalty. The analysis shows that the highest thermohydraulic performance is achieved using the hemispherical roughness elements.
- 1 February 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (6)
Comparison of Heat Transfer and Friction in Pipes With Various Internal Roughness
The heat transfer and friction factor of turbulent pipe flows with different internal roughness are experimentally investigated. Three types of roughness in forms of a mesh, hemispherical elements, and a coil are added to the interior of pipes with an inner diameter of 52.5 mm. The working fluid is air, and the Reynolds numbers vary from 20,000 to 90,000 in increments of 10,000. For investigating the heat transfer, the pipe wall is heated to 375 °C while the inlet air remains at the room temperature. The measurements show that the mesh-type roughness results in a maximum Nusselt number, Nu, increase of approximately 6%, the pipes with hemispherical roughness increased the Nu by a maximum amount of 30%, and the coil increased Nu by up to 60% compared with the smooth pipe. The maximum increase of friction factor is 40% for the pipes with mesh-type roughness, 30% for pipes with hemispherical roughness, and 67% for pipes with coil roughness. The experimental results indicate that adding hemispherical and coil roughness to the internal surface of the pipe can lead to a significant improvement in the rate of heat transfer while adding a mesh-type roughness can have marginal improvements and comes with a large frictional loss penalty. The analysis shows that the highest thermohydraulic performance is achieved using the hemispherical roughness elements.
- Open Access
- 27 June 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 966, A6
Manipulation of a turbulent boundary layer using active surface deformations
We experimentally evaluate whether active wall-normal surface deformations are suitable for the targeted control of very-large-scale motions (VLSMs) in a turbulent boundary layer at a friction Reynolds number of $Re_\tau =2600$ . Circular surface deformations with a diameter $D$ roughly equal to the boundary layer thickness $\delta$ are generated periodically at a constant amplitude of $0.03\delta$ and at actuation frequencies of $St=0.05$ to 0.20, where $St$ is the Strouhal number based on $D$ and the free stream velocity $U_\infty$ . The resulting impact on the flow was captured using high-speed particle image velocimetry and analysed using a triple decomposition. We find that the active surface deformations produce high- and low-speed streamwise velocity fluctuations that are concentrated along the centreline of the actuator. These motions have a negligible impact on the mean velocity profile downstream, i.e. they are truly high and low speed with respect to the unactuated base flow. The motions produced at $St\lesssim 0.1$ are comparable to synthetic VLSMs in terms of their lengths and widths but with a reduced wall-normal extent and rapidly decaying strength. These synthetic motions produce a strong modulation of the turbulence similar to that of the naturally occurring VLSMs. Most notably, we observe that synthetic high-speed motions with magnitudes of the order of $0.05U_\infty$ cause up to a 30 % reduction in turbulence production within the logarithmic layer. The strength and turbulence-modulating characteristics of the synthetic motions appear well suited for targeting the naturally occurring VLSMs locally using a control scheme.- 27 June 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 966, A6
Open AccessManipulation of a turbulent boundary layer using active surface deformations
We experimentally evaluate whether active wall-normal surface deformations are suitable for the targeted control of very-large-scale motions (VLSMs) in a turbulent boundary layer at a friction Reynolds number of $Re_\tau =2600$ . Circular surface deformations with a diameter $D$ roughly equal to the boundary layer thickness $\delta$ are generated periodically at a constant amplitude of $0.03\delta$ and at actuation frequencies of $St=0.05$ to 0.20, where $St$ is the Strouhal number based on $D$ and the free stream velocity $U_\infty$ . The resulting impact on the flow was captured using high-speed particle image velocimetry and analysed using a triple decomposition. We find that the active surface deformations produce high- and low-speed streamwise velocity fluctuations that are concentrated along the centreline of the actuator. These motions have a negligible impact on the mean velocity profile downstream, i.e. they are truly high and low speed with respect to the unactuated base flow. The motions produced at $St\lesssim 0.1$ are comparable to synthetic VLSMs in terms of their lengths and widths but with a reduced wall-normal extent and rapidly decaying strength. These synthetic motions produce a strong modulation of the turbulence similar to that of the naturally occurring VLSMs. Most notably, we observe that synthetic high-speed motions with magnitudes of the order of $0.05U_\infty$ cause up to a 30 % reduction in turbulence production within the logarithmic layer. The strength and turbulence-modulating characteristics of the synthetic motions appear well suited for targeting the naturally occurring VLSMs locally using a control scheme.