Bret N. Flanders
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bret N. Flanders has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
Birol Ozturk
6 shared publicationsRobert C. Dunn
Department of Chemistry, University of Kansas, 1251 Wescoe Dr., Lawrence, KS 66045, USA
5 shared publicationsNorbert F. Scherer
Department of Chemistry, James Franck Institute, and Institute for Biophysical Dynamics, University of Chicago, 5735 S. Ellis Avenue, Chicago, Illinois 60637
4 shared publicationsIshan Talukdar
3 shared publicationsJames P. Wicksted
Department of Physics, Oklahoma State University, Stillwater, USA
3 shared publicationsJohn D. Simon
3 shared publications
Latest Publications
- 20 May 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (24) , 245602
One-step synthesis of graphene via catalyst-free gas-phase hydrocarbon detonation
A one-step, gas-phase, catalyst-free detonation of hydrocarbon (C2H2) method was developed to produce gram quantities of pristine graphene nanosheets (GNs). The detonation of C2H2 was carried out in the presence of O2. The molar ratios of O2/C2H2 were 0.4, 0.5, 0.6, 0.7 and 0.8. The obtained GNs were analyzed by XRD, TEM, XPS and Raman spectroscopy. The GNs are crystalline with a (002) peak centered at 26.05° (d = 0.341 nm). TEM shows that the GNs are stacked in two to three layers and sometimes single layers. An increase in the size of the GNs (35-250 nm) along with a reduction in defects (Raman I(D)/I(G) ~ 1.33-0.28) and specific surface area (187-23 m(2) g(-1)) was found with increasing O2 content. The high temperature of the detonation, ca. 4000 K, is proposed as the cause of graphene production rather than normal soot. The method allows for the control of the number of layers, shape and size of the graphene nanosheets. The process can be scaled up for industrial production.
- 20 May 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (24) , 245602
One-step synthesis of graphene via catalyst-free gas-phase hydrocarbon detonation
A one-step, gas-phase, catalyst-free detonation of hydrocarbon (C2H2) method was developed to produce gram quantities of pristine graphene nanosheets (GNs). The detonation of C2H2 was carried out in the presence of O2. The molar ratios of O2/C2H2 were 0.4, 0.5, 0.6, 0.7 and 0.8. The obtained GNs were analyzed by XRD, TEM, XPS and Raman spectroscopy. The GNs are crystalline with a (002) peak centered at 26.05° (d = 0.341 nm). TEM shows that the GNs are stacked in two to three layers and sometimes single layers. An increase in the size of the GNs (35-250 nm) along with a reduction in defects (Raman I(D)/I(G) ~ 1.33-0.28) and specific surface area (187-23 m(2) g(-1)) was found with increasing O2 content. The high temperature of the detonation, ca. 4000 K, is proposed as the cause of graphene production rather than normal soot. The method allows for the control of the number of layers, shape and size of the graphene nanosheets. The process can be scaled up for industrial production.
- 4 January 2013
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 9 (7) , 2187-2196
Ethanol shock and lysozyme aggregation
Irreversible protein–protein aggregation is associated with several human maladies, including Alzheimer's disease, and poses a challenge to pharmaceutical formulation and preservation efforts. The existence of multiple agglomeration pathways that lead to different final morphologies complicates the ability to determine the aggregation fate of proteins under various reaction conditions. Using lysozyme (3 mg mL−1) as a model protein for dynamic light scattering and circular dichroism studies, we observed dense, non-fibrous aggregation triggered under acidic (pH 4) conditions by a destabilizing “ethanol shock” of 16% (v/v) ethanol. However, ethanol concentrations 15% and below did not lead to aggregation. The aggregation fate of these proteins is thus found to be extremely sensitive to the denaturant concentration. We introduce a stochastic model to explain this dependence based on the denaturant-induced population of a partially unfolded state.
- 4 January 2013
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 9 (7) , 2187-2196
Ethanol shock and lysozyme aggregation
Irreversible protein–protein aggregation is associated with several human maladies, including Alzheimer's disease, and poses a challenge to pharmaceutical formulation and preservation efforts. The existence of multiple agglomeration pathways that lead to different final morphologies complicates the ability to determine the aggregation fate of proteins under various reaction conditions. Using lysozyme (3 mg mL−1) as a model protein for dynamic light scattering and circular dichroism studies, we observed dense, non-fibrous aggregation triggered under acidic (pH 4) conditions by a destabilizing “ethanol shock” of 16% (v/v) ethanol. However, ethanol concentrations 15% and below did not lead to aggregation. The aggregation fate of these proteins is thus found to be extremely sensitive to the denaturant concentration. We introduce a stochastic model to explain this dependence based on the denaturant-induced population of a partially unfolded state.
- 19 October 2012
- Published by IOP Publishing in Nanotechnology
- Vol. 23 (45) , 455105
Long reach cantilevers for sub-cellular force measurements
Maneuverable, high aspect ratio poly(3,4-ethylene dioxythiophene) (PEDOT) fibers are fabricated for use as cellular force probes that can interface with individual pseudopod adhesive contact sites without forming unintentional secondary contacts to the cell. The straight fibers have lengths between 5 and 40 μm and spring constants in the 0.07-23.2 nN μm(-1) range. The spring constants of these fibers were measured directly using an atomic force microscope (AFM). These AFM measurements corroborate determinations based on the transverse vibrational resonance frequencies of the fibers, which is a more convenient method. These fibers are employed to characterize the time dependent forces exerted at adhesive contacts between apical pseudopods of highly migratory D. discoideum cells and the PEDOT fibers, finding an average terminal force of 3.1 ± 2.7 nN and lifetime of 23.4 ± 18.5 s to be associated with these contacts.
- 19 October 2012
- Published by IOP Publishing in Nanotechnology
- Vol. 23 (45) , 455105
Long reach cantilevers for sub-cellular force measurements
Maneuverable, high aspect ratio poly(3,4-ethylene dioxythiophene) (PEDOT) fibers are fabricated for use as cellular force probes that can interface with individual pseudopod adhesive contact sites without forming unintentional secondary contacts to the cell. The straight fibers have lengths between 5 and 40 μm and spring constants in the 0.07-23.2 nN μm(-1) range. The spring constants of these fibers were measured directly using an atomic force microscope (AFM). These AFM measurements corroborate determinations based on the transverse vibrational resonance frequencies of the fibers, which is a more convenient method. These fibers are employed to characterize the time dependent forces exerted at adhesive contacts between apical pseudopods of highly migratory D. discoideum cells and the PEDOT fibers, finding an average terminal force of 3.1 ± 2.7 nN and lifetime of 23.4 ± 18.5 s to be associated with these contacts.
- 10 January 2012
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 26 (01)
DIRECTED ELECTROCHEMICAL NANOWIRE ASSEMBLY: PRECISE NANOSTRUCTURE ASSEMBLY VIA DENDRITIC SOLIDIFICATION
- 10 January 2012
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 26 (01)
DIRECTED ELECTROCHEMICAL NANOWIRE ASSEMBLY: PRECISE NANOSTRUCTURE ASSEMBLY VIA DENDRITIC SOLIDIFICATION
- 29 August 2011
- Published by AIP Publishing in Applied Physics Letters
- Vol. 99 (9) , 093702
Forces at individual pseudopod-filament adhesive contacts
On-chip cellular force sensors are fabricated from cantilever poly(3,4-ethylene dioxythiophene) filaments that visibly deflect under forces exerted at individual pseudopod-filament adhesive contacts. The shape of the deflected filaments and their ∼3 nN/μm spring constants are predicted by cantilever rod theory. Pulling forces exerted by Dictyostelium discoideum cells at these contacts are observed to reach ∼20 nN without breaking the contact.
- 29 August 2011
- Published by AIP Publishing in Applied Physics Letters
- Vol. 99 (9) , 093702
Forces at individual pseudopod-filament adhesive contacts
On-chip cellular force sensors are fabricated from cantilever poly(3,4-ethylene dioxythiophene) filaments that visibly deflect under forces exerted at individual pseudopod-filament adhesive contacts. The shape of the deflected filaments and their ∼3 nN/μm spring constants are predicted by cantilever rod theory. Pulling forces exerted by Dictyostelium discoideum cells at these contacts are observed to reach ∼20 nN without breaking the contact.
- 28 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 17 (4) , 979-984
Spatially Localized Enhancement of Evanescent Coupling to Whispering-Gallery Modes at 1550 nm Due to Surface Plasmon Resonances of Au Nanowires
We demonstrate a highly localized enhancement of evanescent coupling between a tapered optical fiber and a high-Q dielectric microresonator owing to the resonant evanescent excitation of localized surface plasmons of a gold nanowire placed on the microresonator's surface. This localized enhancement, at 1550 nm, is due to nanowire fragments that are confined to specific regions of the surface. The enhancement (of photon-tunneling probability) is measured by comparing properties of the whispering-gallery modes' throughput dips before and after deposition of the nanowire. The experimental results presented here show coupling enhancement by a factor of 10-700, depending on the position of fiber-microresonator contact in relation to the nanowire. These Au-nanowire-coated microresonators could provide enhanced sensitivity in various types of surface-plasmon-based gas, chemical, and biological-sensing applications within the telecommunication frequency bands.
- 28 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 17 (4) , 979-984
Spatially Localized Enhancement of Evanescent Coupling to Whispering-Gallery Modes at 1550 nm Due to Surface Plasmon Resonances of Au Nanowires
We demonstrate a highly localized enhancement of evanescent coupling between a tapered optical fiber and a high-Q dielectric microresonator owing to the resonant evanescent excitation of localized surface plasmons of a gold nanowire placed on the microresonator's surface. This localized enhancement, at 1550 nm, is due to nanowire fragments that are confined to specific regions of the surface. The enhancement (of photon-tunneling probability) is measured by comparing properties of the whispering-gallery modes' throughput dips before and after deposition of the nanowire. The experimental results presented here show coupling enhancement by a factor of 10-700, depending on the position of fiber-microresonator contact in relation to the nanowire. These Au-nanowire-coated microresonators could provide enhanced sensitivity in various types of surface-plasmon-based gas, chemical, and biological-sensing applications within the telecommunication frequency bands.
- 1 January 2010
- Published by Elsevier in Journal of Power Sources
- Vol. 195 (2) , 674-679
Self-supported supercapacitor membranes: Polypyrrole-coated carbon nanotube networks enabled by pulsed electrodeposition
- 1 January 2010
- Published by Elsevier in Journal of Power Sources
- Vol. 195 (2) , 674-679
Self-supported supercapacitor membranes: Polypyrrole-coated carbon nanotube networks enabled by pulsed electrodeposition
- 18 May 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (23) , 235307
Directional growth of metallic and polymeric nanowires
This work delineates the mechanism by which directional nanowire growth occurs in the directed electrochemical nanowire assembly (DENA) technique for growing nanowires on micro-electrode arrays. Indium, polythiophene, and polypyrrole nanowires are the subjects of this study. This technique allows the user to specify the growth path without the use of a mechanical template. Nanowire growth from a user-selected electrode to within +/- 3 microm of the straight line path to a second electrode lying within a approximately 140 degrees angular range and a approximately 100 microm radius of the selected electrode is demonstrated. Theory for one-dimensional electrochemical diffusion in the inter-electrode region reveals that screening of the applied voltage is incomplete, allowing a long range voltage component to extend from the biased to the grounded electrode. Numerical analysis of two-dimensional multi-electrode arrays shows that a linear ridge of electric field maxima bridges the gap between selected electrodes but decays in all other directions. The presence of this anisotropic, long range voltage defines the wire growth path and suppresses the inherent tip splitting tendency of amorphous polymeric materials. This technology allows polythiophene and polypyrrole to be grown as wires rather than fractal aggregates or films, establishing DENA as an on-chip approach to both crystalline metallic and amorphous polymeric nanowire growth.
- 18 May 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (23) , 235307
Directional growth of metallic and polymeric nanowires
This work delineates the mechanism by which directional nanowire growth occurs in the directed electrochemical nanowire assembly (DENA) technique for growing nanowires on micro-electrode arrays. Indium, polythiophene, and polypyrrole nanowires are the subjects of this study. This technique allows the user to specify the growth path without the use of a mechanical template. Nanowire growth from a user-selected electrode to within +/- 3 microm of the straight line path to a second electrode lying within a approximately 140 degrees angular range and a approximately 100 microm radius of the selected electrode is demonstrated. Theory for one-dimensional electrochemical diffusion in the inter-electrode region reveals that screening of the applied voltage is incomplete, allowing a long range voltage component to extend from the biased to the grounded electrode. Numerical analysis of two-dimensional multi-electrode arrays shows that a linear ridge of electric field maxima bridges the gap between selected electrodes but decays in all other directions. The presence of this anisotropic, long range voltage defines the wire growth path and suppresses the inherent tip splitting tendency of amorphous polymeric materials. This technology allows polythiophene and polypyrrole to be grown as wires rather than fractal aggregates or films, establishing DENA as an on-chip approach to both crystalline metallic and amorphous polymeric nanowire growth.
- 19 January 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (3) , 033104
Directional growth of polypyrrole and polythiophene wires
This work establishes an innovative electrochemical approach to the template-free growth of conducting polypyrrole and polythiophene wires along predictable interelectrode paths up to in length. These wires have knobby structures with diameters as small as 98 nm. The conductivity of the polypyrrole wires is ; that of the polythiophene wires is . Controlling the growth path enables fabrication of electrode-wire-target assemblies where the target is a biological cell in the interelectrode gap. Such assemblies are of potential use in cell stimulation studies.- 19 January 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (3) , 033104
Directional growth of polypyrrole and polythiophene wires
This work establishes an innovative electrochemical approach to the template-free growth of conducting polypyrrole and polythiophene wires along predictable interelectrode paths up to in length. These wires have knobby structures with diameters as small as 98 nm. The conductivity of the polypyrrole wires is ; that of the polythiophene wires is . Controlling the growth path enables fabrication of electrode-wire-target assemblies where the target is a biological cell in the interelectrode gap. Such assemblies are of potential use in cell stimulation studies.- 1 January 2009
- Published by Optica Publishing Group
- p. JThE126
Spatially Localized Enhancement of Evanescent Coupling to Whispering-Gallery Modes at 1550 nm Due to Surface Plasmon Resonances of Au Nanowire Fragments
Spatially localized enhanced evanescent coupling between a tapered optical fiber and a high-Q dielectric microresonator results from the resonant excitation of surface plasmons of Au nanowire fragments deposited non-uniformly on the surface of the microresonator.
- 1 January 2009
- Published by Optica Publishing Group
- p. JThE126
Spatially Localized Enhancement of Evanescent Coupling to Whispering-Gallery Modes at 1550 nm Due to Surface Plasmon Resonances of Au Nanowire Fragments
Spatially localized enhanced evanescent coupling between a tapered optical fiber and a high-Q dielectric microresonator results from the resonant excitation of surface plasmons of Au nanowire fragments deposited non-uniformly on the surface of the microresonator.