Mohamad Zul Hilmey Makmud
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohamad Zul Hilmey Makmud has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Yanuar Zulardiansyah Arief
Department of Electrical and Electronic Engineering, Faculty of Engineering, Universiti Malaysia Sarawak, Kota Samarahan, Malaysia
11 shared publications - Hazlee Azil Illias
Universiti Malaya
8 shared publications - Zuhair Jamain
Organic Synthesis and Advanced Materials (OSAM) Research Group, Faculty of Science and Technology, Universiti Malaysia Sabah, Jalan UMS, Kota Kinabalu 88400, Malaysia
8 shared publications - Nor Asiah Muhamad
School of Electrical and Electronic Engineering, Universiti Sains Malaysia, Nibong Tebal, Penang, Malaysia
4 shared publications - Wan Akmal Izzati
Institute of High Voltage and High Current, Faculty of Electrical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
4 shared publications Aulia
Institute of High Voltage & High Current, Faculty of Electrical Engineering, Universiti Teknologi Malaysia Johor Bahru, Malaysia
3 shared publications
Latest Publications
- Open Access
- 16 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 41066-41089
Multifunctional Surface Coatings for Photovoltaic Modules: Anti-Soiling, Hydrophilic/Phobic, and Thermal Management
The performance and long-term reliability of photovoltaic (PV) systems are significantly challenged by three major factors: surface soiling, water or moisture interactions, and thermal stress. Dust and particulate deposition reduce light transmittance, while water-induced degradation and thermal accumulation accelerate module aging. These issues collectively diminish power output, reduce efficiency, and shorten the service life of PV installations, especially in regions with harsh climatic conditions. In recent years, multifunctional surface coatings have emerged as a promising solution to these challenges. Anti-soiling coatings minimize dust adhesion and facilitate natural cleaning through hydrophilic or hydrophobic mechanisms. Hydrophobic and superhydrophobic coatings further improve water repellency and reduce fouling, while thermally resistant coatings mitigate heat buildup and improve operational stability. Beyond enhancing efficiency, such coatings extend durability and reduce maintenance costs, making them vital for large-scale PV deployment. This review consolidates the latest advances in the development and characterization of anti-soiling, hydrophobic, and thermal resistance coatings for PV panels. Emphasis is placed on material categories, fabrication techniques, durability, and multifunctional integration. Furthermore, the paper highlights standardized characterization methods and comparative case studies between laboratory and field performance. Finally, existing research gaps, techno-economic barriers, and future prospects for next-generation PV technologies are discussed. The insights provided aim to guide both academic research and industrial applications toward sustainable, high-performance solar energy solutions.
- 16 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 41066-41089
Open AccessMultifunctional Surface Coatings for Photovoltaic Modules: Anti-Soiling, Hydrophilic/Phobic, and Thermal Management
The performance and long-term reliability of photovoltaic (PV) systems are significantly challenged by three major factors: surface soiling, water or moisture interactions, and thermal stress. Dust and particulate deposition reduce light transmittance, while water-induced degradation and thermal accumulation accelerate module aging. These issues collectively diminish power output, reduce efficiency, and shorten the service life of PV installations, especially in regions with harsh climatic conditions. In recent years, multifunctional surface coatings have emerged as a promising solution to these challenges. Anti-soiling coatings minimize dust adhesion and facilitate natural cleaning through hydrophilic or hydrophobic mechanisms. Hydrophobic and superhydrophobic coatings further improve water repellency and reduce fouling, while thermally resistant coatings mitigate heat buildup and improve operational stability. Beyond enhancing efficiency, such coatings extend durability and reduce maintenance costs, making them vital for large-scale PV deployment. This review consolidates the latest advances in the development and characterization of anti-soiling, hydrophobic, and thermal resistance coatings for PV panels. Emphasis is placed on material categories, fabrication techniques, durability, and multifunctional integration. Furthermore, the paper highlights standardized characterization methods and comparative case studies between laboratory and field performance. Finally, existing research gaps, techno-economic barriers, and future prospects for next-generation PV technologies are discussed. The insights provided aim to guide both academic research and industrial applications toward sustainable, high-performance solar energy solutions.
- Open Access
- 3 December 2025
- Published by Science Publishing Corporation in International Journal of Basic and Applied Sciences
- Vol. 14  (8) , 608-615
Effect of Nanocellulose Reinforcement on The Structural,Dielectric, and ‎Electrical Breakdown of Epoxy Nanocomposites
This study investigates the influence of nanocellulose (NC) on the dielectric and ‎electric field properties of epoxy-based nanocomposites for high-voltage insulation ‎applications. Two types of NC, cellulose nanocrystals (CNC) and cellulose ‎nanofibers (CNF), were incorporated into an epoxy matrix at loadings of 0.5–5.0 ‎wt.%. Morphological analysis by scanning electron microscopy revealed uniform ‎dispersion at low concentrations and increasing agglomeration at higher loadings, ‎particularly in CNF due to its fibrous structure. Electrochemical impedance ‎spectroscopy showed that composites containing 1.0 wt.% CNC and 0.5 wt.% CNF ‎achieved optimal dielectric performance, with reduced relative permittivity (εᵣ ≈ 5.07 ‎for CNC and 5.57 for CNF), suppressed conductivity, and stable capacitive ‎behaviour. COMSOL simulations supported these findings, demonstrating reduced ‎peak electric field intensity (25.8 MV/m) at optimal loadings, indicating improved ‎field uniformity. Breakdown strength tests further confirmed the trend, with CNC ‎at 1.0 wt.% exhibiting 57.9 kV/mm (39% higher than neat epoxy) and CNF at 0.5 ‎wt.% showing 46.7 kV/mm (12% higher than neat epoxy). At higher loadings, ‎aggregation increased permittivity, field crowding, and dielectric loss, leading to ‎reduced insulation performance. Overall, CNC provided broader reinforcement ‎potential than CNF, highlighting nanocellulose as a promising sustainable filler for ‎high-performance epoxy insulation‎.
- 3 December 2025
- Published by Science Publishing Corporation in International Journal of Basic and Applied Sciences
- Vol. 14  (8) , 608-615
Open AccessEffect of Nanocellulose Reinforcement on The Structural,Dielectric, and ‎Electrical Breakdown of Epoxy Nanocomposites
This study investigates the influence of nanocellulose (NC) on the dielectric and ‎electric field properties of epoxy-based nanocomposites for high-voltage insulation ‎applications. Two types of NC, cellulose nanocrystals (CNC) and cellulose ‎nanofibers (CNF), were incorporated into an epoxy matrix at loadings of 0.5–5.0 ‎wt.%. Morphological analysis by scanning electron microscopy revealed uniform ‎dispersion at low concentrations and increasing agglomeration at higher loadings, ‎particularly in CNF due to its fibrous structure. Electrochemical impedance ‎spectroscopy showed that composites containing 1.0 wt.% CNC and 0.5 wt.% CNF ‎achieved optimal dielectric performance, with reduced relative permittivity (εᵣ ≈ 5.07 ‎for CNC and 5.57 for CNF), suppressed conductivity, and stable capacitive ‎behaviour. COMSOL simulations supported these findings, demonstrating reduced ‎peak electric field intensity (25.8 MV/m) at optimal loadings, indicating improved ‎field uniformity. Breakdown strength tests further confirmed the trend, with CNC ‎at 1.0 wt.% exhibiting 57.9 kV/mm (39% higher than neat epoxy) and CNF at 0.5 ‎wt.% showing 46.7 kV/mm (12% higher than neat epoxy). At higher loadings, ‎aggregation increased permittivity, field crowding, and dielectric loss, leading to ‎reduced insulation performance. Overall, CNC provided broader reinforcement ‎potential than CNF, highlighting nanocellulose as a promising sustainable filler for ‎high-performance epoxy insulation‎.
- 27 May 2025
- Published by Springer Nature
- p. 61-66
Breakdown Strength and Fire Retardancy Performance of LLDPE/NR/SiO2 Nanocomposite as High Voltage Insulation
- 27 May 2025
- Published by Springer Nature
- p. 61-66
Breakdown Strength and Fire Retardancy Performance of LLDPE/NR/SiO2 Nanocomposite as High Voltage Insulation
- Open Access
- 11 July 2024
- Published by MDPI AG in Chemengineering
- Vol. 8  (4) , 71
Synthesis and Characterization of Azo-Based Cyclotriphosphazene Compounds: Liquid Crystalline and Dielectric Properties
The study examined the chemical structure of azo-based liquid crystalline compounds that were altered to form a branch of cyclotriphosphazene. Moreover, the research explored the interplay between their mesomorphic and dielectric properties. The structures of the compounds were defined by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, and CHN elemental analysis. Only intermediates 2a–e and cyclotriphosphazene compounds 4d–e were mesogenic with smectic A (SmA) and smectic C (SmC) phases, respectively. Intermediate 2d and compound 4d were used as representative samples to determine the type of liquid crystal, which was confirmed through X-ray diffraction (XRD). The calculated d/L ratios for both compounds were 1.69 and 0.76, respectively, indicating that d was approximately equal to L (d ≈ L ≈ 1). This finding suggests that the SmA and SmC phases observed under polarized optical microscope (POM) are arranged in a monolayer. For the dielectric study, only compounds 2d–e and 4d–e were proceeded and compared for dielectric characteristics testing. The dielectric constants and dielectric loss factors of these four compounds were measured over the frequency range of 100 Hz to 0.1 MHz at room temperature. The dielectric constant trend decreased with the increasing frequency. Meanwhile, the dielectric loss showed two types of trends. The first trend was identical to the dielectric constant trend, in which the dielectric loss decreased as the frequency increased. However, in the second trend, the dielectric loss began to rise with the increase in frequency and then began to fall gradually after reaching a certain peak. Meanwhile, compounds 4d and 4e had low dielectric constants and losses due to the effect of hexasubstituted cyclotriphosphazene that had been attached as a core.
- 11 July 2024
- Published by MDPI AG in Chemengineering
- Vol. 8  (4) , 71
Open AccessSynthesis and Characterization of Azo-Based Cyclotriphosphazene Compounds: Liquid Crystalline and Dielectric Properties
The study examined the chemical structure of azo-based liquid crystalline compounds that were altered to form a branch of cyclotriphosphazene. Moreover, the research explored the interplay between their mesomorphic and dielectric properties. The structures of the compounds were defined by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, and CHN elemental analysis. Only intermediates 2a–e and cyclotriphosphazene compounds 4d–e were mesogenic with smectic A (SmA) and smectic C (SmC) phases, respectively. Intermediate 2d and compound 4d were used as representative samples to determine the type of liquid crystal, which was confirmed through X-ray diffraction (XRD). The calculated d/L ratios for both compounds were 1.69 and 0.76, respectively, indicating that d was approximately equal to L (d ≈ L ≈ 1). This finding suggests that the SmA and SmC phases observed under polarized optical microscope (POM) are arranged in a monolayer. For the dielectric study, only compounds 2d–e and 4d–e were proceeded and compared for dielectric characteristics testing. The dielectric constants and dielectric loss factors of these four compounds were measured over the frequency range of 100 Hz to 0.1 MHz at room temperature. The dielectric constant trend decreased with the increasing frequency. Meanwhile, the dielectric loss showed two types of trends. The first trend was identical to the dielectric constant trend, in which the dielectric loss decreased as the frequency increased. However, in the second trend, the dielectric loss began to rise with the increase in frequency and then began to fall gradually after reaching a certain peak. Meanwhile, compounds 4d and 4e had low dielectric constants and losses due to the effect of hexasubstituted cyclotriphosphazene that had been attached as a core.
- Open Access
- 1 January 2024
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 32
Enhancement of structural and dielectric properties of PVC/CNC nanocomposites as electrical insulation materials
This work aims to introduce bio-based nanocomposite as high voltage electrical insulation material by using cellulose nanocrystal (CNC) isolated from filter paper as a filler of polymer matrix, in this case, polyvinyl chloride (PVC). CNC is obtained via acid hydrolysis treatment and incorporated into PVC by using the casting method at different concentrations. The structural and thermal characterization have been investigated using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The dielectric properties as a function of the alternating current (AC) sinusoidal frequency of PVC/CNC were examined by the electrical impedance spectroscopy (EIS) test method. Breakdown voltage tests according to the ASTM D149 standard were conducted to determine the dielectric strength of nanocomposites. Hence, the results indicate that the addition of CNC by 1 wt% is the best formulation to improve the base polymer structure, in this case PVC, as well as its dielectric insulation properties.
- 1 January 2024
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 32
Open AccessEnhancement of structural and dielectric properties of PVC/CNC nanocomposites as electrical insulation materials
This work aims to introduce bio-based nanocomposite as high voltage electrical insulation material by using cellulose nanocrystal (CNC) isolated from filter paper as a filler of polymer matrix, in this case, polyvinyl chloride (PVC). CNC is obtained via acid hydrolysis treatment and incorporated into PVC by using the casting method at different concentrations. The structural and thermal characterization have been investigated using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The dielectric properties as a function of the alternating current (AC) sinusoidal frequency of PVC/CNC were examined by the electrical impedance spectroscopy (EIS) test method. Breakdown voltage tests according to the ASTM D149 standard were conducted to determine the dielectric strength of nanocomposites. Hence, the results indicate that the addition of CNC by 1 wt% is the best formulation to improve the base polymer structure, in this case PVC, as well as its dielectric insulation properties.
- Open Access
Optimal Design of Corona Ring for 132 kV Insulator at High Voltage Transmission Lines Based on Optimisation Techniques
The installation of a corona ring on an insulator string on a transmission line is one of the solutions to reduce the electric field stress surrounding the energised end of the insulator string. However, installing a corona ring with an optimum design to reduce the electric field magnitude on an insulator string is a challenging task. Therefore, in this work, a method to achieve the optimum design of a corona ring for 132 kV composite non-ceramic insulator string was proposed using two optimisation methods: the Imperialist Competitive Algorithm (ICA) and Grey Wolf Optimisation (GWO). A composite non-ceramic insulator string geometry with and without a corona ring was modelled in finite element analysis and used to obtain the electric field distribution in the model geometry. The electric field distribution was evaluated using a variation in the corona ring’s dimensions, i.e., the ring diameter, the ring tube diameter and the vertical position of the ring along the insulator string. From the results achieved, a comparison of the minimum electric field magnitude along the insulator string with a corona ring design shows that the minimum electric field magnitude is found to be lower using optimisation techniques compared to without using optimisation techniques by between 3.724% and 3.827%. Hence, this indicates the capability and effectiveness of the proposed methods in achieving the optimum design of a corona ring on an insulator string.
Open AccessOptimal Design of Corona Ring for 132 kV Insulator at High Voltage Transmission Lines Based on Optimisation Techniques
The installation of a corona ring on an insulator string on a transmission line is one of the solutions to reduce the electric field stress surrounding the energised end of the insulator string. However, installing a corona ring with an optimum design to reduce the electric field magnitude on an insulator string is a challenging task. Therefore, in this work, a method to achieve the optimum design of a corona ring for 132 kV composite non-ceramic insulator string was proposed using two optimisation methods: the Imperialist Competitive Algorithm (ICA) and Grey Wolf Optimisation (GWO). A composite non-ceramic insulator string geometry with and without a corona ring was modelled in finite element analysis and used to obtain the electric field distribution in the model geometry. The electric field distribution was evaluated using a variation in the corona ring’s dimensions, i.e., the ring diameter, the ring tube diameter and the vertical position of the ring along the insulator string. From the results achieved, a comparison of the minimum electric field magnitude along the insulator string with a corona ring design shows that the minimum electric field magnitude is found to be lower using optimisation techniques compared to without using optimisation techniques by between 3.724% and 3.827%. Hence, this indicates the capability and effectiveness of the proposed methods in achieving the optimum design of a corona ring on an insulator string.
- Open Access
Fire Retardancy and Dielectric Strength of Cyclotriphosphazene Compounds with Schiff Base and Ester Linking Units Attached to the Electron-Withdrawing Side Arm
A series of compounds with Schiff base and ester linking units attached to the electron-withdrawing side arm (Cl, NO2, and OH) have been successfully synthesized through four schemes of the chemical route. These compounds were characterized using Fourier Transform Infrared spectroscopy (FTIR), Nuclear Magnetic Resonance spectroscopy (NMR), and Carbon, Hydrogen and Nitrogen (CHN) elemental analysis. The epoxy resin was used as a matrix of molding to observe the refinement of fire-retardant properties of the modified cyclotriphosphazene compounds. The fire-retardant testing was done using Limiting Oxygen Index (LOI). The LOI value of pure epoxy resin was increased from 22.75% to 24.71% when incorporated with 1 wt.% of hexasubstituted cyclotriphosphazene (HCCP). Interestingly, all the final compounds gave a positive increment in the LOI value and the highest LOI value was obtained from the compound containing a nitro side arm with LOI value of 26.90%. In order to understand the thermal stability of these compounds, Thermogravimetric Analysis (TGA) was carried out. The compound with the nitro group at the terminal end has the highest char residue which is 34.2% at 700 °C. This indicated that the presence of the nitro withdrawing group was able to enhance the fire retardancy of the materials. Based on SEM observation, the shape of the final compound’s char residue demonstrated the formation of a porous protective layer with a dense surface. The dielectric property was conducted according to ASTM D149 AC breakdown voltage to determine its dielectric strength. The results showed that the highest dielectric strength value belonged to the compound containing a nitro group side arm with 24.41 kV/mm−1 due to the π electron delocalization.
Open AccessFire Retardancy and Dielectric Strength of Cyclotriphosphazene Compounds with Schiff Base and Ester Linking Units Attached to the Electron-Withdrawing Side Arm
A series of compounds with Schiff base and ester linking units attached to the electron-withdrawing side arm (Cl, NO2, and OH) have been successfully synthesized through four schemes of the chemical route. These compounds were characterized using Fourier Transform Infrared spectroscopy (FTIR), Nuclear Magnetic Resonance spectroscopy (NMR), and Carbon, Hydrogen and Nitrogen (CHN) elemental analysis. The epoxy resin was used as a matrix of molding to observe the refinement of fire-retardant properties of the modified cyclotriphosphazene compounds. The fire-retardant testing was done using Limiting Oxygen Index (LOI). The LOI value of pure epoxy resin was increased from 22.75% to 24.71% when incorporated with 1 wt.% of hexasubstituted cyclotriphosphazene (HCCP). Interestingly, all the final compounds gave a positive increment in the LOI value and the highest LOI value was obtained from the compound containing a nitro side arm with LOI value of 26.90%. In order to understand the thermal stability of these compounds, Thermogravimetric Analysis (TGA) was carried out. The compound with the nitro group at the terminal end has the highest char residue which is 34.2% at 700 °C. This indicated that the presence of the nitro withdrawing group was able to enhance the fire retardancy of the materials. Based on SEM observation, the shape of the final compound’s char residue demonstrated the formation of a porous protective layer with a dense surface. The dielectric property was conducted according to ASTM D149 AC breakdown voltage to determine its dielectric strength. The results showed that the highest dielectric strength value belonged to the compound containing a nitro group side arm with 24.41 kV/mm−1 due to the π electron delocalization.