Payam Molla-Abbasi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Payam Molla-Abbasi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Ehsan Danesh
Amirkabir University of Technology
3 shared publicationsSeyed Reza Ghaffarian
Amirkabir University of Technology
3 shared publicationsKamran Janghorban
Department of Chemical Engineering, Farahan Branch, Islamic Azad University, Farahan, Iran
2 shared publicationsMahsa S. Asgari
Arak University
2 shared publicationsMeisam Shabanian
Faculty of Chemistry and Petrochemical Engineering, Standard Research Institute (SRI), Karaj, Islamic Republic of Iran
2 shared publications- Seyed Reza Ghaffarian
Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran, Iran
2 shared publications
Latest Publications
- 4 January 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (3) , 1258-1273
Fabrication of a packaging film based on PLA blends: The evolution of physical, mechanical, and rheological properties
Today, the use of biodegradable polymers has become widespread in a wide range of industries. This research scrutinized the physical, mechanical, and rheological properties of poly (lactic acid)/poly (ethylene oxide)/carbon nanotube (PLA/PEO/CNTs) blend nanocomposites, as a good candidate for usage in the packaging industry. PEO and CNTs were added at various concentrations to improve the flexibility, toughness, gas permeability, thermal stability, and mechanical properties of PLA via solution blending. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Field Emission Scanning Electron Microscope (FESEM), water contact angle (WCA), rheometric mechanical spectrometer (RMS) test, gas permeability, and tensile characterization were performed to characterize the properties of the prepared blends and nanocomposites. The experimental results revealed that the addition of 25 wt% PEO to the PLA matrix made a partially miscible blend with a droplet‐matrix morphology. PEO at this concentration increased the elongation at break (from 2.2% to 18%) while reducing the modulus (from 25 to 6 MPa). Also, the experimental results indicated that the miscibility of PLA and PEO was enhanced by the addition of 1 wt% CNTs to the prepared blend, associated with diminished entropy of mixing in the LCST phase diagram. Theoretical calculations predicted that the CNTs would be localized in the PLA phase which increased the total crystallinity of the sample by 28%, considerably reducing the amount of gas permeation into the nanocomposite. In addition, the introduction of the CNTs to the blend increased the elongation at break and tensile strength by 13% compared to pure PLA and lowered the rate of thermal degradation effectively. Also, the final results showed that the COOH‐CNTs located in the PEO phase caused a decline in the crystallinity and an increase in the gas permeability of the prepared nanocomposite.Highlights: Improvement of physical properties of PLA by blending with PEO and CNTs. A deep investigation on rheological behavior of the prepared nanocomposite. Increasing the crystallinity degree of PLA/PEO blend by adding CNTs. Improvement of the miscibility between PLA and PEO in the presence of CNTs. Controlling the CNTs localization by surface modification.
- 4 January 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (3) , 1258-1273
Fabrication of a packaging film based on PLA blends: The evolution of physical, mechanical, and rheological properties
Today, the use of biodegradable polymers has become widespread in a wide range of industries. This research scrutinized the physical, mechanical, and rheological properties of poly (lactic acid)/poly (ethylene oxide)/carbon nanotube (PLA/PEO/CNTs) blend nanocomposites, as a good candidate for usage in the packaging industry. PEO and CNTs were added at various concentrations to improve the flexibility, toughness, gas permeability, thermal stability, and mechanical properties of PLA via solution blending. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Field Emission Scanning Electron Microscope (FESEM), water contact angle (WCA), rheometric mechanical spectrometer (RMS) test, gas permeability, and tensile characterization were performed to characterize the properties of the prepared blends and nanocomposites. The experimental results revealed that the addition of 25 wt% PEO to the PLA matrix made a partially miscible blend with a droplet‐matrix morphology. PEO at this concentration increased the elongation at break (from 2.2% to 18%) while reducing the modulus (from 25 to 6 MPa). Also, the experimental results indicated that the miscibility of PLA and PEO was enhanced by the addition of 1 wt% CNTs to the prepared blend, associated with diminished entropy of mixing in the LCST phase diagram. Theoretical calculations predicted that the CNTs would be localized in the PLA phase which increased the total crystallinity of the sample by 28%, considerably reducing the amount of gas permeation into the nanocomposite. In addition, the introduction of the CNTs to the blend increased the elongation at break and tensile strength by 13% compared to pure PLA and lowered the rate of thermal degradation effectively. Also, the final results showed that the COOH‐CNTs located in the PEO phase caused a decline in the crystallinity and an increase in the gas permeability of the prepared nanocomposite.Highlights: Improvement of physical properties of PLA by blending with PEO and CNTs. A deep investigation on rheological behavior of the prepared nanocomposite. Increasing the crystallinity degree of PLA/PEO blend by adding CNTs. Improvement of the miscibility between PLA and PEO in the presence of CNTs. Controlling the CNTs localization by surface modification.
- 18 January 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (3) , 1637-1655
Design and characterization of high‐performance epoxy adhesive with block copolymer and alumina nanoparticles in aluminum‐aluminum bonded joints: Mechanical properties, lap shear strength, and thermal stability
In this research, phenolic resin and poly (butyl‐acrylate‐block‐styrene) copolymer were used in the formulation of epoxy adhesive to improve its thermal stability and toughness. Also, in order to improve the mechanical properties such as the modulus and tensile strength, aluminum oxide nanoparticles (NPs) were added to the epoxy based resin. Effects of different factors such as percent contents of phenolic resin, toughening agent, and aluminum oxide NPs on the microstructure, mechanical properties, and thermal stability of the epoxy‐based adhesives were investigated. Thermogravimetric analysis, Fourier transform infrared spectroscopy, and field‐emission scanning electron microscopy were used to investigate the thermal, mechanical, and morphological properties of the prepared epoxy adhesive samples. In addition, the curing kinetics of the optimal specimens was studied based on differential scanning calorimetry (DSC). The experimental results indicated that the phenolic decreased strength of dog‐bone samples, while increased the adhesion strength in metal‐to‐metal single‐lap strength. On the other hand, addition of block‐copolymers as toughening agent led to a consistent decrease in the modulus as well as increasing the tensile strength. Also, results of single‐lap strength tests showed that, in the optimal quad system, the four components exhibit synergetic effects and show a single‐lap strength that is 152% higher than that of pure epoxy. The DSC analysis indicated that the presence of alumina NPs and block‐copolymers tend to reduce the initial curing temperature while increasing the curing reaction heat.
- 18 January 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (3) , 1637-1655
Design and characterization of high‐performance epoxy adhesive with block copolymer and alumina nanoparticles in aluminum‐aluminum bonded joints: Mechanical properties, lap shear strength, and thermal stability
In this research, phenolic resin and poly (butyl‐acrylate‐block‐styrene) copolymer were used in the formulation of epoxy adhesive to improve its thermal stability and toughness. Also, in order to improve the mechanical properties such as the modulus and tensile strength, aluminum oxide nanoparticles (NPs) were added to the epoxy based resin. Effects of different factors such as percent contents of phenolic resin, toughening agent, and aluminum oxide NPs on the microstructure, mechanical properties, and thermal stability of the epoxy‐based adhesives were investigated. Thermogravimetric analysis, Fourier transform infrared spectroscopy, and field‐emission scanning electron microscopy were used to investigate the thermal, mechanical, and morphological properties of the prepared epoxy adhesive samples. In addition, the curing kinetics of the optimal specimens was studied based on differential scanning calorimetry (DSC). The experimental results indicated that the phenolic decreased strength of dog‐bone samples, while increased the adhesion strength in metal‐to‐metal single‐lap strength. On the other hand, addition of block‐copolymers as toughening agent led to a consistent decrease in the modulus as well as increasing the tensile strength. Also, results of single‐lap strength tests showed that, in the optimal quad system, the four components exhibit synergetic effects and show a single‐lap strength that is 152% higher than that of pure epoxy. The DSC analysis indicated that the presence of alumina NPs and block‐copolymers tend to reduce the initial curing temperature while increasing the curing reaction heat.
- 23 November 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 33 (3) , 760-769
Organic compound gas detector based on polylactic acid/poly (styrene‐co‐acrylonitrile)/multi‐walled carbon nanotube blend composite with co‐continuous microstructure
A conductive polymer composite (CPC) based on polylactic acid (PLA)/poly (styrene‐co‐acrylonitrile) (SAN)/multi‐walled carbon nanotubes (MWNT) blend was prepared and used as a sensitive layer for detecting methanol, ethanol, toluene, and water vapor. The response behavior of polymer blend nanocomposite in comparison with PLA‐MWNT and SAN‐MWNT sensitive layers was studied as well as the influence of solution blending on the morphology, electrical behavior, and performance parameters of prepared sensitive layers. The scanning electron microscopy micrograph results showed that the PLA/SAN solution blended with a 50/50 wt% ratio had formed the co‐continuous morphology. In addition, the electrical conductivity investigation revealed that the percolation threshold of sensitive layers decreased from 1.5 vol%, related to PLA‐MWNT, to 0.8 vol%, related PLA/SAN blend nanocomposite. Thermodynamic investigation revealed that, in the solution blended conductive composites, MWNTs are preferentially localized in the PLA phase. The relative response (Rrel) of blended conductive composite, in comparison with PLA‐MWNT, was increased toward ethanol and toluene vapor while it was decreased against the methanol vapor. The sensitivity behavior of polymer blend composite was investigated based on the double percolated conductive network as well as the thermodynamic parameters such as Flory‐Huggins interaction parameter and solubility parameters.
- 23 November 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 33 (3) , 760-769
Organic compound gas detector based on polylactic acid/poly (styrene‐co‐acrylonitrile)/multi‐walled carbon nanotube blend composite with co‐continuous microstructure
A conductive polymer composite (CPC) based on polylactic acid (PLA)/poly (styrene‐co‐acrylonitrile) (SAN)/multi‐walled carbon nanotubes (MWNT) blend was prepared and used as a sensitive layer for detecting methanol, ethanol, toluene, and water vapor. The response behavior of polymer blend nanocomposite in comparison with PLA‐MWNT and SAN‐MWNT sensitive layers was studied as well as the influence of solution blending on the morphology, electrical behavior, and performance parameters of prepared sensitive layers. The scanning electron microscopy micrograph results showed that the PLA/SAN solution blended with a 50/50 wt% ratio had formed the co‐continuous morphology. In addition, the electrical conductivity investigation revealed that the percolation threshold of sensitive layers decreased from 1.5 vol%, related to PLA‐MWNT, to 0.8 vol%, related PLA/SAN blend nanocomposite. Thermodynamic investigation revealed that, in the solution blended conductive composites, MWNTs are preferentially localized in the PLA phase. The relative response (Rrel) of blended conductive composite, in comparison with PLA‐MWNT, was increased toward ethanol and toluene vapor while it was decreased against the methanol vapor. The sensitivity behavior of polymer blend composite was investigated based on the double percolated conductive network as well as the thermodynamic parameters such as Flory‐Huggins interaction parameter and solubility parameters.
- 15 September 2020
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (1) , 391-401
Effect of nano‐size nodular structure induced by CNT‐promoted phase separation on the fabrication of superhydrophobic polyvinyl chloride films
The nonsolvent‐induced phase separation (NIPS) method was employed to fabricate the porous films based on polyvinyl chloride loaded with carbon nanotubes (CNTs). The combinational addition of CNTs and a proper nonsolvent (ethanol) resulted in a porous surface layer with the nano‐size nodular structure possessing an exact superhydrophobic behavior (water contact angle [WCA] = 157° and sliding angle [SA] <5°). The size of PVC nodules at the surface layer varies in the range of 200 to 800 nm depending on the nonsolvent concentrations, and polymer molecular weight. The effects of various nonsolvent concentrations as well as PVC molecular weight on the surface properties of the films were also investigated. Morphological and roughness analyses revealed the pronounced role of PVC molecular weight on the size of nodules, and the structural uniformity of the surface morphology based on the thermodynamic parameters such as relaxation time and dynamic of polymer chains. The concurrent use of CNTs and nonsolvent led to promote the NIPS process due to the nucleating role of CNTs, which were localized within the polymer‐rich phase leading to an ultra‐fine and packed nodular surface structure. Transmission electron microscopy results also proved the very well dispersion quality of CNTs. Glass transition temperature of PVC was also assessed, and the results were correlated to the associating ability of CNTs with polymer chains during the phase separation process. Overall, the promising potential of CNT/ethanol combination on the surface porosity and hydrophobicity of PVC nanocomposite films was revealed in this study, which could further extend its application window.
- 15 September 2020
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (1) , 391-401
Effect of nano‐size nodular structure induced by CNT‐promoted phase separation on the fabrication of superhydrophobic polyvinyl chloride films
The nonsolvent‐induced phase separation (NIPS) method was employed to fabricate the porous films based on polyvinyl chloride loaded with carbon nanotubes (CNTs). The combinational addition of CNTs and a proper nonsolvent (ethanol) resulted in a porous surface layer with the nano‐size nodular structure possessing an exact superhydrophobic behavior (water contact angle [WCA] = 157° and sliding angle [SA] <5°). The size of PVC nodules at the surface layer varies in the range of 200 to 800 nm depending on the nonsolvent concentrations, and polymer molecular weight. The effects of various nonsolvent concentrations as well as PVC molecular weight on the surface properties of the films were also investigated. Morphological and roughness analyses revealed the pronounced role of PVC molecular weight on the size of nodules, and the structural uniformity of the surface morphology based on the thermodynamic parameters such as relaxation time and dynamic of polymer chains. The concurrent use of CNTs and nonsolvent led to promote the NIPS process due to the nucleating role of CNTs, which were localized within the polymer‐rich phase leading to an ultra‐fine and packed nodular surface structure. Transmission electron microscopy results also proved the very well dispersion quality of CNTs. Glass transition temperature of PVC was also assessed, and the results were correlated to the associating ability of CNTs with polymer chains during the phase separation process. Overall, the promising potential of CNT/ethanol combination on the surface porosity and hydrophobicity of PVC nanocomposite films was revealed in this study, which could further extend its application window.
- 1 May 2020
- Published by Wiley in Polymer Engineering & Science
- Vol. 60 (7) , 1631-1641
An analytical investigation on the effect of porous conductive cellulose acetate composite morphology on the detection of organic compounds
A smart porous conductive polymer composite (CPC) consisting of cellulose acetate as matrix and multiwalled carbon nanotubes as conductive filler was prepared to detect a set of lung cancer biomarkers. The solvent evaporation‐induced phase separation was used to introduce porosity into the conductive composite. The prepared sensitive layers exhibited high response intensity, low response time, and good recovery behavior toward the mentioned analytes. A thorough investigation was conducted on the morphology, response behavior, sensitivity, and selectivity of the prepared CPC transducer. The selectivity of responses was considered based on the thermodynamic and kinetic characteristics of polymer and analytes such as Hansen solubility parameters, Flory‐Huggins interaction parameter, and diffusion coefficient of analytes into the polymer membrane. Moreover, the microstructure of porous layers was characterized by using SEM, contact angle, and BET. The volume porosity and specific surface area of the sensitive layers were increased by the introduction of porosity into the polymer composite, causing the improvement of sensing parameters. The obtained responses further confirmed the promising potential of the prepared porous CPC structure, for the detection of lung cancer biomarkers, from exhaled breath as an inexpensive, repeatable, accurate, and noninvasive method.
- 1 May 2020
- Published by Wiley in Polymer Engineering & Science
- Vol. 60 (7) , 1631-1641
An analytical investigation on the effect of porous conductive cellulose acetate composite morphology on the detection of organic compounds
A smart porous conductive polymer composite (CPC) consisting of cellulose acetate as matrix and multiwalled carbon nanotubes as conductive filler was prepared to detect a set of lung cancer biomarkers. The solvent evaporation‐induced phase separation was used to introduce porosity into the conductive composite. The prepared sensitive layers exhibited high response intensity, low response time, and good recovery behavior toward the mentioned analytes. A thorough investigation was conducted on the morphology, response behavior, sensitivity, and selectivity of the prepared CPC transducer. The selectivity of responses was considered based on the thermodynamic and kinetic characteristics of polymer and analytes such as Hansen solubility parameters, Flory‐Huggins interaction parameter, and diffusion coefficient of analytes into the polymer membrane. Moreover, the microstructure of porous layers was characterized by using SEM, contact angle, and BET. The volume porosity and specific surface area of the sensitive layers were increased by the introduction of porosity into the polymer composite, causing the improvement of sensing parameters. The obtained responses further confirmed the promising potential of the prepared porous CPC structure, for the detection of lung cancer biomarkers, from exhaled breath as an inexpensive, repeatable, accurate, and noninvasive method.
- 7 March 2020
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 29 (4) , 341-350
Tuning the polymer–graphene interfaces by picric acid molecules to improve the sensitivity of a prepared conductive polymer composite gas detector
- 7 March 2020
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 29 (4) , 341-350
Tuning the polymer–graphene interfaces by picric acid molecules to improve the sensitivity of a prepared conductive polymer composite gas detector
- 6 February 2019
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 28 (3) , 203-211
A bulky aromatic functional polyimide composite as a sensitive layer for the detection of organic compound biomarkers
- 6 February 2019
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 28 (3) , 203-211
A bulky aromatic functional polyimide composite as a sensitive layer for the detection of organic compound biomarkers
- Open Access
- 1 December 2017
- Vol. 3 (4) , 211-218
Modified CNTs/Nafion composite: The role of sulfonate groups on the performance of prepared proton exchange methanol fuel cell’s membrane
- 1 December 2017
- Vol. 3 (4) , 211-218
Open AccessModified CNTs/Nafion composite: The role of sulfonate groups on the performance of prepared proton exchange methanol fuel cell’s membrane
- 1 December 2017
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 27 (2) , 77-86
A novel heteropolyacid-doped carbon nanotubes/Nafion nanocomposite membrane for high performance proton-exchange methanol fuel cell applications
- 1 December 2017
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 27 (2) , 77-86
A novel heteropolyacid-doped carbon nanotubes/Nafion nanocomposite membrane for high performance proton-exchange methanol fuel cell applications