Ahmed M. Heikal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmed M. Heikal has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Farhat O. Hameed
Center for Nanotechnology, Zewail City of Science, Technology and Innovation, 6th of October City, Giza, Egypt
11 shared publications - Salah Sabry Ahmed Obayya
Centre for Photonics and Smart Materials, Zewail City of Science, Technology and Innovation, 6th of October City, Giza, Egypt
11 shared publications - Firas Faeq K. Hussain
Engineering Applications of Lasers Department, National Institute of Laser Enhanced Sciences, Cairo University, Giza, Egypt
2 shared publications - B. M. Azizur Rahman
School of Science and Technology, City University of London, London EC1V 0HB, UK
1 shared publication - B. M. Younis
Nanoelectronics Integrated Systems Center, Nile University, Giza, 12588, Egypt
1 shared publication Basel H. Almewafy
Department of Electronics and Communications Engineering Faculty of Engineering Mansoura University Mansoura 35516 Egypt
1 shared publication
Latest Publications
- 12 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 28 (1) , 59-62
Highly Sensitive Plasmonic Photonic Crystal Temperature Sensor Filled With Liquid Crystal
A novel highly sensitive surface plasmon resonance-based liquid crystal (LC) photonic crystal fiber (PCF) temperature sensor is presented and studied. Through this letter, the coupling characteristics between the core guided mode inside the PCF core infiltrated with nematic LC and surface plasmon mode on the surface of nano gold wire are studied in detail. The structural geometrical parameters of the proposed design, such as number of metal rods, core diameter, and metal rod diameter are optimized to achieve highly temperature sensitivity. The suggested sensor of compact device length of 20 μm proved to surpass the recent sensors with high sensitivity of 10 nm/°C. The results are calculated using a full-vectorial finite-element method with irregular meshing capabilities and perfectly matched layer boundary conditions.
- 12 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 28 (1) , 59-62
Highly Sensitive Plasmonic Photonic Crystal Temperature Sensor Filled With Liquid Crystal
A novel highly sensitive surface plasmon resonance-based liquid crystal (LC) photonic crystal fiber (PCF) temperature sensor is presented and studied. Through this letter, the coupling characteristics between the core guided mode inside the PCF core infiltrated with nematic LC and surface plasmon mode on the surface of nano gold wire are studied in detail. The structural geometrical parameters of the proposed design, such as number of metal rods, core diameter, and metal rod diameter are optimized to achieve highly temperature sensitivity. The suggested sensor of compact device length of 20 μm proved to surpass the recent sensors with high sensitivity of 10 nm/°C. The results are calculated using a full-vectorial finite-element method with irregular meshing capabilities and perfectly matched layer boundary conditions.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 33 (13) , 2868-2875
Efficient Polarization Filter Design Based on Plasmonic Photonic Crystal Fiber
A novel selectively metal-filled spiral photonic crystal fiber with an elliptic core is introduced and analyzed. The cladding air holes of the suggested design are arranged in spiral arms that are distributed in an elliptical form. In this paper, the dispersion characteristics and loss spectra of the reported design are studied through the full-vectorial finite-element method. The suggested design has advantages in terms of highly polarization-dependent coupling between x- and y-polarized core modes and higher order surface plasmon polariton (SPP) modes. It is evident from this study that the core modes can be separated from each other by changing the structure parameters. In addition, the resonance points at which the coupling between the core modes and SPP modes occurs can be tuned. Moreover, the coupling tunability of the proposed design can be increased by filling the cladding air hole with multiple metal wires. This novel structure is suitable for the design of filter-based applications. At wavelength λ = 1.013 μm, the loss of the x-polarized core mode is equal to 77.04 dB/mm, while it is only 2.765 dB/mm for the y-polarized core mode with single metal rod. However, for two metal rods, the losses for x- and y-polarized core modes are increased to 94.1 and 6.424 dB/mm, respectively, at λ = 0.98 μm.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 33 (13) , 2868-2875
Efficient Polarization Filter Design Based on Plasmonic Photonic Crystal Fiber
A novel selectively metal-filled spiral photonic crystal fiber with an elliptic core is introduced and analyzed. The cladding air holes of the suggested design are arranged in spiral arms that are distributed in an elliptical form. In this paper, the dispersion characteristics and loss spectra of the reported design are studied through the full-vectorial finite-element method. The suggested design has advantages in terms of highly polarization-dependent coupling between x- and y-polarized core modes and higher order surface plasmon polariton (SPP) modes. It is evident from this study that the core modes can be separated from each other by changing the structure parameters. In addition, the resonance points at which the coupling between the core modes and SPP modes occurs can be tuned. Moreover, the coupling tunability of the proposed design can be increased by filling the cladding air hole with multiple metal wires. This novel structure is suitable for the design of filter-based applications. At wavelength λ = 1.013 μm, the loss of the x-polarized core mode is equal to 77.04 dB/mm, while it is only 2.765 dB/mm for the y-polarized core mode with single metal rod. However, for two metal rods, the losses for x- and y-polarized core modes are increased to 94.1 and 6.424 dB/mm, respectively, at λ = 0.98 μm.
- Open Access
- 1 April 2015
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 9 (2) , 37-42
Porous core photonic crystal fibre with metal‐coated central hole for terahertz applications
In this study, a novel design of porous octagonal photonic crystal fibre with a metal‐coated central hole is investigated and analysed in the terahertz (THz) range. The suggested structure is analysed near a frequency of 1.0 THz by using the full vectorial finite difference method. The effects of the structure geometrical parameters and bending radius on the mode effective index, effective mode area and attenuation of the proposed design are investigated. The numerical results reveal that the effective mode area with a metal‐coated central hole is smaller than that of porous core without a metal‐coated central hole by 80%. In addition, very low attenuation can be obtained because of the porosity inside the core region.
- 1 April 2015
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 9 (2) , 37-42
Open AccessPorous core photonic crystal fibre with metal‐coated central hole for terahertz applications
In this study, a novel design of porous octagonal photonic crystal fibre with a metal‐coated central hole is investigated and analysed in the terahertz (THz) range. The suggested structure is analysed near a frequency of 1.0 THz by using the full vectorial finite difference method. The effects of the structure geometrical parameters and bending radius on the mode effective index, effective mode area and attenuation of the proposed design are investigated. The numerical results reveal that the effective mode area with a metal‐coated central hole is smaller than that of porous core without a metal‐coated central hole by 80%. In addition, very low attenuation can be obtained because of the porosity inside the core region.
- 9 March 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (6) , 7007-7020
Ultra-high tunable liquid crystal-plasmonic photonic crystal fiber polarization filter
A novel ultra-high tunable photonic crystal fiber (PCF) polarization filter is proposed and analyzed using finite element method. The suggested design has a central hole infiltrated with a nematic liquid crystal (NLC) that offers high tunability with temperature and external electric field. Moreover, the PCF is selectively filled with metal wires into cladding air holes. Results show that the resonance losses and wavelengths are different in x and y polarized directions depending on the rotation angle φ of the NLC. The reported filter of compact device length 0.5 mm can achieve 600 dB / cm resonance losses at φ = 90° for x-polarized mode at communication wavelength of 1300 mm with low losses of 0.00751 dB / cm for y-polarized mode. However, resonance losses of 157.71 dB / cm at φ = 0° can be achieved for y-polarized mode at the same wavelength with low losses of 0.092 dB / cm for x-polarized mode.
- 9 March 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (6) , 7007-7020
Ultra-high tunable liquid crystal-plasmonic photonic crystal fiber polarization filter
A novel ultra-high tunable photonic crystal fiber (PCF) polarization filter is proposed and analyzed using finite element method. The suggested design has a central hole infiltrated with a nematic liquid crystal (NLC) that offers high tunability with temperature and external electric field. Moreover, the PCF is selectively filled with metal wires into cladding air holes. Results show that the resonance losses and wavelengths are different in x and y polarized directions depending on the rotation angle φ of the NLC. The reported filter of compact device length 0.5 mm can achieve 600 dB / cm resonance losses at φ = 90° for x-polarized mode at communication wavelength of 1300 mm with low losses of 0.00751 dB / cm for y-polarized mode. However, resonance losses of 157.71 dB / cm at φ = 0° can be achieved for y-polarized mode at the same wavelength with low losses of 0.092 dB / cm for x-polarized mode.
- 15 May 2014
- Published by SPIE-Intl Soc Optical Eng
- p. 91412D-91412D-7
Compact microring resonator sensor based on three-trenched channel plasmonic waveguide
- 15 May 2014
- Published by SPIE-Intl Soc Optical Eng
- p. 91412D-91412D-7
Compact microring resonator sensor based on three-trenched channel plasmonic waveguide
- 29 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 50 (6) , 474-482
Dispersion Characteristics of Asymmetric Channel Plasmon Polariton Waveguides
A novel asymmetric channel plasmon polaritons (CPPs) is proposed and analyzed. In this paper, the dispersion characteristics of asymmetric two and three-trenched CPPs structures are studied in detail. The suggested asymmetric structures have advantages in terms of propagation length and figure of merit over the symmetric CPP waveguides. In addition, a comparative study of various CPP metals including gold and silver is also presented. It is found that the propagation length and figure of merit of the silver-based structures are better than those of gold-based structures. In addition, the effect of bending on the asymmetric CPP waveguides is investigated. The simulation results are obtained by full-vectorial finite difference method with irregular meshing capabilities and perfectly matched layer boundary conditions.
- 29 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 50 (6) , 474-482
Dispersion Characteristics of Asymmetric Channel Plasmon Polariton Waveguides
A novel asymmetric channel plasmon polaritons (CPPs) is proposed and analyzed. In this paper, the dispersion characteristics of asymmetric two and three-trenched CPPs structures are studied in detail. The suggested asymmetric structures have advantages in terms of propagation length and figure of merit over the symmetric CPP waveguides. In addition, a comparative study of various CPP metals including gold and silver is also presented. It is found that the propagation length and figure of merit of the silver-based structures are better than those of gold-based structures. In addition, the effect of bending on the asymmetric CPP waveguides is investigated. The simulation results are obtained by full-vectorial finite difference method with irregular meshing capabilities and perfectly matched layer boundary conditions.
- Open Access
- 1 August 2013
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 7 (4) , 85-92
Analysis of polarisation conversion in cascaded bent photonic crystal fibre
A rigorous analysis of polarisation conversion in a novel design of cascaded bent silica photonic crystal fibre is proposed using full vectorial finite difference method as well as full vectorial finite difference beam propagation method. The influence of different structural geometrical parameters on the polarisation rotator performance is investigated. The numerical results reveal that by a careful adjustment of the structural geometrical parameters and bending radius, nearly a 100% polarisation conversion ratio with nine sections only and low bending losses can be achieved.
- 1 August 2013
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 7 (4) , 85-92
Open AccessAnalysis of polarisation conversion in cascaded bent photonic crystal fibre
A rigorous analysis of polarisation conversion in a novel design of cascaded bent silica photonic crystal fibre is proposed using full vectorial finite difference method as well as full vectorial finite difference beam propagation method. The influence of different structural geometrical parameters on the polarisation rotator performance is investigated. The numerical results reveal that by a careful adjustment of the structural geometrical parameters and bending radius, nearly a 100% polarisation conversion ratio with nine sections only and low bending losses can be achieved.
- 26 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 25 (16) , 1578-1581
Novel Passive Polarization Rotator Based on Spiral Photonic Crystal Fiber
In this letter, a novel design of a passive ultra-compact polarization rotator based on soft glass equiangular spiral photonic crystal fiber (ES-PCF) is proposed and analyzed using full vectorial finite difference approaches. The suggested ES-PCF has eight arms with a central elliptical air hole, which can be shifted in $x$ and $y$ directions to achieve complete polarization conversion. In addition, the major axis of the elliptical hole is rotated by 45 $^{\circ}$, which offers 99% polarization conversion ratio with ultra-compact device length of 96 $\mu{\rm m}$. It is also evident from the numerical results that the polarization rotation would be more than 98% over the 1.5–1.6 $\mu{\rm m}$ wavelength range.- 26 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 25 (16) , 1578-1581
Novel Passive Polarization Rotator Based on Spiral Photonic Crystal Fiber
In this letter, a novel design of a passive ultra-compact polarization rotator based on soft glass equiangular spiral photonic crystal fiber (ES-PCF) is proposed and analyzed using full vectorial finite difference approaches. The suggested ES-PCF has eight arms with a central elliptical air hole, which can be shifted in $x$ and $y$ directions to achieve complete polarization conversion. In addition, the major axis of the elliptical hole is rotated by 45 $^{\circ}$, which offers 99% polarization conversion ratio with ultra-compact device length of 96 $\mu{\rm m}$. It is also evident from the numerical results that the polarization rotation would be more than 98% over the 1.5–1.6 $\mu{\rm m}$ wavelength range.- 29 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 49 (8) , 621-627
Coupling Characteristic of a Novel Hybrid Long-Range Plasmonic Waveguide Including Bends
In this paper, the modal analysis of a novel design of a hybrid long-range plasmonic waveguide is introduced and analyzed using the full-vectorial finite difference method. The suggested design has high index material as a cap to reduce the propagation loss and optimum bending radius as well. The analyzed parameters are the real effective index and propagation loss. In addition, the bending analysis of the reported design is introduced. The coupling is performed between three different waveguides: straight dielectric waveguide, straight hybrid long-range plasmon waveguide, and uniformly bent hybrid one.
- 29 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 49 (8) , 621-627
Coupling Characteristic of a Novel Hybrid Long-Range Plasmonic Waveguide Including Bends
In this paper, the modal analysis of a novel design of a hybrid long-range plasmonic waveguide is introduced and analyzed using the full-vectorial finite difference method. The suggested design has high index material as a cap to reduce the propagation loss and optimum bending radius as well. The analyzed parameters are the real effective index and propagation loss. In addition, the bending analysis of the reported design is introduced. The coupling is performed between three different waveguides: straight dielectric waveguide, straight hybrid long-range plasmon waveguide, and uniformly bent hybrid one.