Wannarat Chueangchayaphan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wannarat Chueangchayaphan has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Narong Chueangchayaphan
Faculty of Science and Industrial Technology Prince of Songkla University Surat Thani Thailand
7 shared publications- Narong Chueangchayaphan
Faculty of Science and Industrial Technology, Prince of Songkla University, Surat Thani Campus, Surat Thani 84000, Thailand
5 shared publications Piyawadee Luangchuang
Faculty of Science and Industrial Technology Prince of Songkla University Surat Thani Thailand
3 shared publicationsWarisara Borapak
Faculty of Science and Industrial Technology, Prince of Songkla University, Surat Thani, Thailand
3 shared publicationsMuhammad Azwadi Sulaiman
Advanced Materials Research Cluster Faculty of Bioengineering and Technology, Universiti Malaysia Kelantan Jeli Malaysia
2 shared publicationsPhatchariya Nooun
Faculty of Science and Industrial Technology, Prince of Songkla University, Surat Thani Campus Surat Thani Thailand
2 shared publications
Latest Publications
- 4 March 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (22)
Incorporating Ginger Extract as a Bioactive Additive Into Eco‐Friendly Fertilizer Coatings Based on Natural Rubber‐Grafted‐Rice Starch: A Performance Evaluation
A polymeric coating was developed to minimize fertilizer loss and improve antifungal efficacy against Fusarium sp. by combining natural rubber‐grafted rice starch (NR‐g‐ST) with methanolic ginger extract (GE) for coating granular urea fertilizer. The coating was synthesized via in situ graft copolymerization, employing potassium persulfate as an initiator within an emulsion system. Fourier transform infrared (FT‐IR) spectroscopy confirmed successful grafting and molecular interactions between the hydroxyl groups of starch with both GE and natural rubber (NR). The NR:ST ratio was maintained at 70:30 wt%, while GE content was varied from 0 to 9 wt% relative to the polymer matrix. The coatings were characterized using thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and water contact angle (WCA) measurements. Increasing GE content enhanced the mechanical properties, storage modulus, and hydrophobicity while reducing biodegradability. The coating demonstrated antifungal efficacy through the inhibition of Fusarium sp. mycelial growth, suggesting its potential as a multifunctional agricultural solution.
- 4 March 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (22)
Incorporating Ginger Extract as a Bioactive Additive Into Eco‐Friendly Fertilizer Coatings Based on Natural Rubber‐Grafted‐Rice Starch: A Performance Evaluation
A polymeric coating was developed to minimize fertilizer loss and improve antifungal efficacy against Fusarium sp. by combining natural rubber‐grafted rice starch (NR‐g‐ST) with methanolic ginger extract (GE) for coating granular urea fertilizer. The coating was synthesized via in situ graft copolymerization, employing potassium persulfate as an initiator within an emulsion system. Fourier transform infrared (FT‐IR) spectroscopy confirmed successful grafting and molecular interactions between the hydroxyl groups of starch with both GE and natural rubber (NR). The NR:ST ratio was maintained at 70:30 wt%, while GE content was varied from 0 to 9 wt% relative to the polymer matrix. The coatings were characterized using thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and water contact angle (WCA) measurements. Increasing GE content enhanced the mechanical properties, storage modulus, and hydrophobicity while reducing biodegradability. The coating demonstrated antifungal efficacy through the inhibition of Fusarium sp. mycelial growth, suggesting its potential as a multifunctional agricultural solution.
- Open Access
Evaluating Oil Palm Trunk Biochar and Palm Oil as Environmentally Friendly Sustainable Additives in Green Natural Rubber Composites
This research examines the possibility of palm oil and oil palm trunk biochar (OPTB) from pyrolysis effectively serving as alternative processing oils and fillers, substituting petroleum-based counterparts in natural rubber (NR) composites. Chemical, elemental, surface and morphological analyses were used to characterize both carbon black (CB) and OPTB, by using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) gas porosimetry, and scanning electron microscopy (SEM). The influences of OPTB contents from 0 to 100 parts per hundred rubber (phr) on thermal, dielectric, dynamic mechanical, and cure characteristics, and the key mechanical properties of particulate NR-composites were investigated. OPTB enhanced the characteristics of the composites, as demonstrated by a rise in dielectric constant, thermal stability, storage modulus, glass transition temperature (Tg), hardness and modulus at 300% elongation, along with a decrease in the loss tangent (tan δ). Tear strength exhibited an increase with OPTB content up to a specific threshold, whereas tensile strength and elongation at break declined. This implies a compromise between the various mechanical properties when incorporating OPTB as a filler. This work supports the potential application of OPTB as a renewable substitute for CB in the rubber industry, particularly in tire production and other industrial rubber applications, which would also bring environmental, sustainability, and economic benefits for the palm oil-related industry.
Open AccessEvaluating Oil Palm Trunk Biochar and Palm Oil as Environmentally Friendly Sustainable Additives in Green Natural Rubber Composites
This research examines the possibility of palm oil and oil palm trunk biochar (OPTB) from pyrolysis effectively serving as alternative processing oils and fillers, substituting petroleum-based counterparts in natural rubber (NR) composites. Chemical, elemental, surface and morphological analyses were used to characterize both carbon black (CB) and OPTB, by using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) gas porosimetry, and scanning electron microscopy (SEM). The influences of OPTB contents from 0 to 100 parts per hundred rubber (phr) on thermal, dielectric, dynamic mechanical, and cure characteristics, and the key mechanical properties of particulate NR-composites were investigated. OPTB enhanced the characteristics of the composites, as demonstrated by a rise in dielectric constant, thermal stability, storage modulus, glass transition temperature (Tg), hardness and modulus at 300% elongation, along with a decrease in the loss tangent (tan δ). Tear strength exhibited an increase with OPTB content up to a specific threshold, whereas tensile strength and elongation at break declined. This implies a compromise between the various mechanical properties when incorporating OPTB as a filler. This work supports the potential application of OPTB as a renewable substitute for CB in the rubber industry, particularly in tire production and other industrial rubber applications, which would also bring environmental, sustainability, and economic benefits for the palm oil-related industry.
- Open Access
High Performance of Titanium Dioxide Reinforced Acrylonitrile Butadiene Rubber Composites
Recently, dielectric elastomer actuators (DEA) have emerged as one of the most promising materials for use in soft robots. However, DEA needs a high operating voltage and high mechanical properties. By increasing the dielectric constant of elastomeric materials, it is possible to decrease the operating voltage required. Thus, elastomeric composites with a high dielectric constant and strong mechanical properties are of interest. The aim of this research was to investigate the effect of titanium dioxide (TiO2) content ranging from 0 to 110 phr on the cure characteristics, and physical, dielectric, dynamic mechanical, and morphological properties of acrylonitrile butadiene rubber (NBR) composites. The addition of TiO2 reduced the scorch time (ts1) as well as the optimum cure time (tc90) but increased the cure rate index (CRI), minimum torque (ML), maximum torque (MH), and delta torque (MH − ML). The optimal TiO2 content for maximum tensile strength and elongation at break was 90 phr. Tensile strength and elongation at break were increased by 144.8% and 40.1%, respectively, over pure NBR. A significant mechanical property improvement was observed for TiO2-filled composites due to the good dispersion of TiO2 in the NBR matrix, which was confirmed by scanning electron microscopy (SEM). Moreover, incorporating TiO2 filler gave a higher storage modulus, a shift in glass transition temperature (Tg) to a higher temperature, and reduced damping in dynamic mechanical thermal analysis (DMTA). The addition of TiO2 to NBR rubber increased the dielectric constant of the resultant composites in the tested frequency range from 102 to 105 Hz. As a result, TiO2-filled NBR composite has a high potential for dielectric elastomer actuator applications.
Open AccessHigh Performance of Titanium Dioxide Reinforced Acrylonitrile Butadiene Rubber Composites
Recently, dielectric elastomer actuators (DEA) have emerged as one of the most promising materials for use in soft robots. However, DEA needs a high operating voltage and high mechanical properties. By increasing the dielectric constant of elastomeric materials, it is possible to decrease the operating voltage required. Thus, elastomeric composites with a high dielectric constant and strong mechanical properties are of interest. The aim of this research was to investigate the effect of titanium dioxide (TiO2) content ranging from 0 to 110 phr on the cure characteristics, and physical, dielectric, dynamic mechanical, and morphological properties of acrylonitrile butadiene rubber (NBR) composites. The addition of TiO2 reduced the scorch time (ts1) as well as the optimum cure time (tc90) but increased the cure rate index (CRI), minimum torque (ML), maximum torque (MH), and delta torque (MH − ML). The optimal TiO2 content for maximum tensile strength and elongation at break was 90 phr. Tensile strength and elongation at break were increased by 144.8% and 40.1%, respectively, over pure NBR. A significant mechanical property improvement was observed for TiO2-filled composites due to the good dispersion of TiO2 in the NBR matrix, which was confirmed by scanning electron microscopy (SEM). Moreover, incorporating TiO2 filler gave a higher storage modulus, a shift in glass transition temperature (Tg) to a higher temperature, and reduced damping in dynamic mechanical thermal analysis (DMTA). The addition of TiO2 to NBR rubber increased the dielectric constant of the resultant composites in the tested frequency range from 102 to 105 Hz. As a result, TiO2-filled NBR composite has a high potential for dielectric elastomer actuator applications.
- 31 August 2020
- Published by Wiley in Polymer International
- Vol. 70 (1) , 154-161
Characterization of barium titanate reinforced acrylonitrile butadiene rubber composites for flexible electronic applications: influences of barium titanate content
The aim of this study was to develop high dielectric constant flexible polymers with a highly efficient and cost‐effective approach using acrylonitrile butadiene rubber (NBR) as the polymer matrix and barium titanate (BT) as the high dielectric constant filler. The BT powder was synthesized with a solid‐state reaction and was characterized using a particle size analyzer, XRD, SEM and Fourier transform infrared spectroscopy. NBR/BT composites were fabricated using an internal mixer with various BT loadings up to 160 phr. The influence of BT loading on the cure characteristics and mechanical, dynamic mechanical, thermal, dielectric and morphological properties was determined. The incorporation of BT in the NBR matrix shortened scorch time and increased delta torque. The mechanical properties, thermal stability and dielectric constant were greatly improved and increased with BT loading. The results suggest that the reinforcement effect was achieved due to strong hydrogen bonding or polar–polar interactions between NBR matrix and BT filler. This is further corroborated by the good dispersion of BT filler in the NBR matrix observed with SEM imaging. These findings can be applied to produce high‐performance dielectric elastomers. © 2020 Society of Industrial Chemistry
- 31 August 2020
- Published by Wiley in Polymer International
- Vol. 70 (1) , 154-161
Characterization of barium titanate reinforced acrylonitrile butadiene rubber composites for flexible electronic applications: influences of barium titanate content
The aim of this study was to develop high dielectric constant flexible polymers with a highly efficient and cost‐effective approach using acrylonitrile butadiene rubber (NBR) as the polymer matrix and barium titanate (BT) as the high dielectric constant filler. The BT powder was synthesized with a solid‐state reaction and was characterized using a particle size analyzer, XRD, SEM and Fourier transform infrared spectroscopy. NBR/BT composites were fabricated using an internal mixer with various BT loadings up to 160 phr. The influence of BT loading on the cure characteristics and mechanical, dynamic mechanical, thermal, dielectric and morphological properties was determined. The incorporation of BT in the NBR matrix shortened scorch time and increased delta torque. The mechanical properties, thermal stability and dielectric constant were greatly improved and increased with BT loading. The results suggest that the reinforcement effect was achieved due to strong hydrogen bonding or polar–polar interactions between NBR matrix and BT filler. This is further corroborated by the good dispersion of BT filler in the NBR matrix observed with SEM imaging. These findings can be applied to produce high‐performance dielectric elastomers. © 2020 Society of Industrial Chemistry
- 20 April 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (4) , 2009-2023
Cure characteristics and physico-mechanical properties of natural rubber/silica composites: effect of natural rubber-graft-poly(2-hydroxyethyl acrylate) content
- 20 April 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (4) , 2009-2023
Cure characteristics and physico-mechanical properties of natural rubber/silica composites: effect of natural rubber-graft-poly(2-hydroxyethyl acrylate) content
- 1 April 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (4) , 1755-1769
High permittivity ceramics-filled acrylonitrile butadiene rubber composites: influence of acrylonitrile content and ceramic type
- 1 April 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (4) , 1755-1769
High permittivity ceramics-filled acrylonitrile butadiene rubber composites: influence of acrylonitrile content and ceramic type
- 20 February 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (38) , 49136
Evaluation of cure characteristic, physico‐mechanical, and dielectric properties of calcium copper titanate filled acrylonitrile‐butadiene rubber composites: Effect of calcium copper titanate loading
Calcium copper titanate (CCTO) has been synthesized by high temperature solid‐state reaction from calcium carbonate, copper (II) oxide, and titanium dioxide as the starting materials. The formation and morphology of CCTO were confirmed by X‐ray diffraction, Fourier‐transformed infrared spectrophotometry, scanning electron microscopy (SEM), and particle size analysis. In order to develop flexible dielectric materials, acrylonitrile‐butadiene rubber (NBR)‐based composites were prepared with CCTO content varied from 0 to 120 phr (parts per hundred rubber). The cure characteristics of composites were assessed. High‐dielectric constant CCTO particles were blended into NBR to make composites with improved dielectric constant. Results showed that the NBR/CCTO composites had a high dielectric constant (10–20) with low dielectric loss (−3μS/cm) at frequencies up to 106Hz. However, the higher CCTO loadings had agglomeration in the NBR matrix, and thus tensile strength and elongation at break sharply deteriorated due to poor rubber‐filler interactions. The results showed lower storage modulusE′ and a reduction inTgwith the incorporation of CCTO in NBR matrix. Moreover, improved thermal stability of the NBR/CCTO composites was achieved. SEM was used to observe the dispersion of CCTO particles in NBR matrix.
- 20 February 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (38) , 49136
Evaluation of cure characteristic, physico‐mechanical, and dielectric properties of calcium copper titanate filled acrylonitrile‐butadiene rubber composites: Effect of calcium copper titanate loading
Calcium copper titanate (CCTO) has been synthesized by high temperature solid‐state reaction from calcium carbonate, copper (II) oxide, and titanium dioxide as the starting materials. The formation and morphology of CCTO were confirmed by X‐ray diffraction, Fourier‐transformed infrared spectrophotometry, scanning electron microscopy (SEM), and particle size analysis. In order to develop flexible dielectric materials, acrylonitrile‐butadiene rubber (NBR)‐based composites were prepared with CCTO content varied from 0 to 120 phr (parts per hundred rubber). The cure characteristics of composites were assessed. High‐dielectric constant CCTO particles were blended into NBR to make composites with improved dielectric constant. Results showed that the NBR/CCTO composites had a high dielectric constant (10–20) with low dielectric loss (−3μS/cm) at frequencies up to 106Hz. However, the higher CCTO loadings had agglomeration in the NBR matrix, and thus tensile strength and elongation at break sharply deteriorated due to poor rubber‐filler interactions. The results showed lower storage modulusE′ and a reduction inTgwith the incorporation of CCTO in NBR matrix. Moreover, improved thermal stability of the NBR/CCTO composites was achieved. SEM was used to observe the dispersion of CCTO particles in NBR matrix.
- 21 November 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (22)
Natural rubber‐graft‐poly(2‐hydroxyethyl acrylate) on cure characteristics and mechanical properties of silica‐filled natural rubber composites
The grafting of poly(2‐hydroxyethyl acrylate) onto natural rubber (NR‐g‐PHEA) was used to compatibilize NR composites with silica filler. The NR/silica compounds were prepared with various grafting percentages of NR‐g‐PHEA (0, 6.5, 10.5, and 14.5%) and fixed amounts of 3 parts per hundred of rubber (phr) NR‐g‐PHEA and 20 phr silica. The cure characteristics were examined using a moving die rheometer. The physicomechanical properties of NR/silica composites were determined in terms of tensile strength, bound rubber content, and dynamic mechanical analysis. Thermal properties were assessed with thermogravimetric analysis. The results showed that scorch time and cure time tend to decrease with the level of grafting in NR‐g‐PHEA. The NR‐g‐PHEA decreased tan δ, whereas bound rubber content in NR/silica compounds increased, which indicates improved silica dispersion in the NR matrix. The mechanical properties improved with level of grafting in NR‐g‐PHEA. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48738.
- 21 November 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (22)
Natural rubber‐graft‐poly(2‐hydroxyethyl acrylate) on cure characteristics and mechanical properties of silica‐filled natural rubber composites
The grafting of poly(2‐hydroxyethyl acrylate) onto natural rubber (NR‐g‐PHEA) was used to compatibilize NR composites with silica filler. The NR/silica compounds were prepared with various grafting percentages of NR‐g‐PHEA (0, 6.5, 10.5, and 14.5%) and fixed amounts of 3 parts per hundred of rubber (phr) NR‐g‐PHEA and 20 phr silica. The cure characteristics were examined using a moving die rheometer. The physicomechanical properties of NR/silica composites were determined in terms of tensile strength, bound rubber content, and dynamic mechanical analysis. Thermal properties were assessed with thermogravimetric analysis. The results showed that scorch time and cure time tend to decrease with the level of grafting in NR‐g‐PHEA. The NR‐g‐PHEA decreased tan δ, whereas bound rubber content in NR/silica compounds increased, which indicates improved silica dispersion in the NR matrix. The mechanical properties improved with level of grafting in NR‐g‐PHEA. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48738.
- 29 January 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 76 (11) , 5889-5902
Influence of Al2O3 particle size on properties of thermoplastic starch–TiO2–Al2O3 composites
- 29 January 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 76 (11) , 5889-5902
Influence of Al2O3 particle size on properties of thermoplastic starch–TiO2–Al2O3 composites