Wenjing Su
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wenjing Su has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Manos M. Tentzeris
Georgia Institute of Technology
6 shared publications - Luca Roselli
University of Perugia
5 shared publications Manos M. Tentzeris
Georgia Institute of Technology, School of Electrical and Computer Engineering, Atlanta, GA 30332-250, USA
5 shared publicationsBenjamin S. Cook
Texas Instruments, Kilby Labs, Dallas, TX 75243, USA
3 shared publications- Jiang Zhu
Meta Platform
3 shared publications B. S. Cook
2 shared publications
Latest Publications
- Open Access
- 24 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 4, 207-215
Wearable Antennas for Virtual Reality Cross-Body Links
Cross-body link refers to the wireless connection between two wearable devices when they are both worn or near the body, such as that of a virtual reality (VR) headset and its controllers. It is one of the most challenging wireless scenarios in terms of link budget, due to severe shadowing effects when controllers are placed at the back side of the body. This is especially true when the users are in an outdoor environment where there is less reflection from the surrounding. This paper investigates the wireless propagation mechanism, including line-of-sight, ground reflection, and creeping waves. Based on that, through simulation and measurement experiments, this work analyzes the impact of different antenna designs on the cross-body link of VR/AR devices, including one novel compact low-profile antenna named Distributed Monopole (DM), and two conventional antennas. Due to the polarization advantages, both the novel DM antenna and the patch antenna shows significantly better performance than the dipole antenna. The DM antenna also shows a 2-4 dB advantage over the patch antenna due to its omni-directional field pattern. Time-domain analysis and statistical approaches are suggested to fully characterize the cross-body link of VR/AR antennas and body propagation.
- 24 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 4, 207-215
Open AccessWearable Antennas for Virtual Reality Cross-Body Links
Cross-body link refers to the wireless connection between two wearable devices when they are both worn or near the body, such as that of a virtual reality (VR) headset and its controllers. It is one of the most challenging wireless scenarios in terms of link budget, due to severe shadowing effects when controllers are placed at the back side of the body. This is especially true when the users are in an outdoor environment where there is less reflection from the surrounding. This paper investigates the wireless propagation mechanism, including line-of-sight, ground reflection, and creeping waves. Based on that, through simulation and measurement experiments, this work analyzes the impact of different antenna designs on the cross-body link of VR/AR devices, including one novel compact low-profile antenna named Distributed Monopole (DM), and two conventional antennas. Due to the polarization advantages, both the novel DM antenna and the patch antenna shows significantly better performance than the dipole antenna. The DM antenna also shows a 2-4 dB advantage over the patch antenna due to its omni-directional field pattern. Time-domain analysis and statistical approaches are suggested to fully characterize the cross-body link of VR/AR antennas and body propagation.
- Open Access
- 1 January 2022
- Published by HICSS Conference Office
Joint Planning of Natural Gas and Electric Power Transmission with Spatially Correlated Failures
- 1 January 2022
- Published by HICSS Conference Office
Open AccessJoint Planning of Natural Gas and Electric Power Transmission with Spatially Correlated Failures
- Open Access
- 24 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 58575-58584
Wearable Antennas for Cross-Body Communication and Human Activity Recognition
This paper proposes a novel miniaturized wearable antenna (mosaic antenna) for cross-body communication featuring a superior performance compared to five commonly utilized wearable antenna topologies. The proposed mosaic antenna optimally excites the surface waves to enable cross-body communication yet still with a low profile and a miniaturized size. As a proof-of-concept of the unique capabilities of this antenna, an inkjet-printed flexible wearable prototype on Polytetrafluoroethylene (PTFE, also known as Teflon) has been fabricated in a highly customizable, scalable and low-cost process and has been used as an enabler for human activities recognition coupled with machine learning techniques powered by Google TensorFlow. By utilizing proof-of-concept on-body networks consisting of mosaic antennas, human activity can be detected with an accuracy 91.9% for RF signal-based recognition techniques, despite the variability among different users and environments.
- 24 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 58575-58584
Open AccessWearable Antennas for Cross-Body Communication and Human Activity Recognition
This paper proposes a novel miniaturized wearable antenna (mosaic antenna) for cross-body communication featuring a superior performance compared to five commonly utilized wearable antenna topologies. The proposed mosaic antenna optimally excites the surface waves to enable cross-body communication yet still with a low profile and a miniaturized size. As a proof-of-concept of the unique capabilities of this antenna, an inkjet-printed flexible wearable prototype on Polytetrafluoroethylene (PTFE, also known as Teflon) has been fabricated in a highly customizable, scalable and low-cost process and has been used as an enabler for human activities recognition coupled with machine learning techniques powered by Google TensorFlow. By utilizing proof-of-concept on-body networks consisting of mosaic antennas, human activity can be detected with an accuracy 91.9% for RF signal-based recognition techniques, despite the variability among different users and environments.
- Open Access
- 6 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 46585-46595
RFID Based Non-Contact Human Activity Detection Exploiting Cross Polarization
This paper explores antenna’s polarization for Radio-Frequency Identification (RFID) based non-contact human activity detection. For the first time, a cross circular polarization configuration between reader antenna and tag antenna is proposed to increase the sensing range and spatial sensitivity. Compared to conventional RFID configurations -linearly polarized (LP) tag and circularly polarized (CP) reader, a cross CP configuration can improve the signal-to-noise ratio (SNR) which leads to 230% increase in the detection area over traditional approach in our experiment. As the result of the improvement of spatial sensitivity, the proposed approach can detect subtle and small body movements at almost 4.5m from the reader, such as head movements or even respiration, which enables a low-cost, easy-to-use, non-contact and non-intrusive monitoring of the elderly and disabled peoples in places like hospitals and assisted living homes.
- 6 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 46585-46595
Open AccessRFID Based Non-Contact Human Activity Detection Exploiting Cross Polarization
This paper explores antenna’s polarization for Radio-Frequency Identification (RFID) based non-contact human activity detection. For the first time, a cross circular polarization configuration between reader antenna and tag antenna is proposed to increase the sensing range and spatial sensitivity. Compared to conventional RFID configurations -linearly polarized (LP) tag and circularly polarized (CP) reader, a cross CP configuration can improve the signal-to-noise ratio (SNR) which leads to 230% increase in the detection area over traditional approach in our experiment. As the result of the improvement of spatial sensitivity, the proposed approach can detect subtle and small body movements at almost 4.5m from the reader, such as head movements or even respiration, which enables a low-cost, easy-to-use, non-contact and non-intrusive monitoring of the elderly and disabled peoples in places like hospitals and assisted living homes.
- 25 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2716-2724
Additively Manufactured mm-Wave Multichip Modules With Fully Printed “Smart” Encapsulation Structures
This article presents the first time that an millimeter-wave (mm-wave) multichip module (MCM) with on-demand “smart” encapsulation has been fabricated utilizing additive manufacturing technologies. RF and dc interconnects were fabricated using inkjet printing, while the encapsulation was realized using 3-D printing. Inkjet-printed interconnects feature superior RF performance, better mechanical reliability, and on-demand, low-cost fabrication process. Numerous test vehicles were initially produced to evaluate these additive manufacturing technologies and compare them with traditional ribbon bonding, exhibiting a superior |S21| performance throughout the whole operation range up to 40 GHz with a peak of 3.3 dB better gain for a Ka-band low noise amplifier (LNA). A fully functioning front-end MCM was fabricated using the same inkjet-printed interconnect technology, which features smart encapsulation technology fabricated using the 3-D printing and integrated on-demand “smart” encapsulation for electromagnetic interference (EMI) mitigation. The proof-of-concept MCM demonstrates exceptional performance taking advantage of a lowcost, on-demand additive manufacturing method that requires minimal tooling and process steps, which can drastically accelerate the time to market for future 5G and Internet-of-Things applications. The methodologies presented in this article could potentially enable rapid production of high-performance, highfrequency customizable circuit packaging structures with ondemand “smart” features, such as self-diagnostics, EMI/EMC filtering, and integrated sensors.
- 25 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2716-2724
Additively Manufactured mm-Wave Multichip Modules With Fully Printed “Smart” Encapsulation Structures
This article presents the first time that an millimeter-wave (mm-wave) multichip module (MCM) with on-demand “smart” encapsulation has been fabricated utilizing additive manufacturing technologies. RF and dc interconnects were fabricated using inkjet printing, while the encapsulation was realized using 3-D printing. Inkjet-printed interconnects feature superior RF performance, better mechanical reliability, and on-demand, low-cost fabrication process. Numerous test vehicles were initially produced to evaluate these additive manufacturing technologies and compare them with traditional ribbon bonding, exhibiting a superior |S21| performance throughout the whole operation range up to 40 GHz with a peak of 3.3 dB better gain for a Ka-band low noise amplifier (LNA). A fully functioning front-end MCM was fabricated using the same inkjet-printed interconnect technology, which features smart encapsulation technology fabricated using the 3-D printing and integrated on-demand “smart” encapsulation for electromagnetic interference (EMI) mitigation. The proof-of-concept MCM demonstrates exceptional performance taking advantage of a lowcost, on-demand additive manufacturing method that requires minimal tooling and process steps, which can drastically accelerate the time to market for future 5G and Internet-of-Things applications. The methodologies presented in this article could potentially enable rapid production of high-performance, highfrequency customizable circuit packaging structures with ondemand “smart” features, such as self-diagnostics, EMI/EMC filtering, and integrated sensors.
- 22 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 18 (11) , 2272-2276
Read/Interrogation Enhancement of Chipless RFIDs Using Machine Learning Techniques
This work describes the implementation of a machine learning (ML) classification strategy for read/interrogation enhancement in chipless Radio Frequency Identification (RFID) applications. A novel ML-based approach for classification and of detection tag IDs has been presented which can perform effective transponder readings for a wide variety of ranges and contexts, while providing tag-ID detection accuracy of up to 98.3%. Four tags encoding the four 2-bit IDs were inkjetprinted onto a flexible low-cost PET substrate and interrogated without cross-talk or clutter interference deembedding at ranges up to 40cm, with different orientations and with and without the presence of scattering objects in the vicinity of the tags and reader. A Support Vector Machine (SVM) algorithm was then trained using 259 measurements and its accuracy was tested and characterized as a function of the included training data. Finally, the excellent performance of the approach, displaying reading accuracies ranging from 89.6% to 99.3%, is reported. This effort sets a precedent, opening the door to a rich and wide area of research for the implementation of ML methods for the enhancement of chipless RFID identification applications.
- 22 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 18 (11) , 2272-2276
Read/Interrogation Enhancement of Chipless RFIDs Using Machine Learning Techniques
This work describes the implementation of a machine learning (ML) classification strategy for read/interrogation enhancement in chipless Radio Frequency Identification (RFID) applications. A novel ML-based approach for classification and of detection tag IDs has been presented which can perform effective transponder readings for a wide variety of ranges and contexts, while providing tag-ID detection accuracy of up to 98.3%. Four tags encoding the four 2-bit IDs were inkjetprinted onto a flexible low-cost PET substrate and interrogated without cross-talk or clutter interference deembedding at ranges up to 40cm, with different orientations and with and without the presence of scattering objects in the vicinity of the tags and reader. A Support Vector Machine (SVM) algorithm was then trained using 259 measurements and its accuracy was tested and characterized as a function of the included training data. Finally, the excellent performance of the approach, displaying reading accuracies ranging from 89.6% to 99.3%, is reported. This effort sets a precedent, opening the door to a rich and wide area of research for the implementation of ML methods for the enhancement of chipless RFID identification applications.
- 27 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (7) , 1434-1447
3-D-Printing-Based Selective-Ink-Deposition Technique Enabling Complex Antenna and RF Structures for 5G Applications up to 6 GHz
This paper introduces a novel additivemanufacturing technique to obtain high-resolution selective-ink-deposition on complex 3-D objects, packages, and modules for 5G applications. The technique consists of embossing the desired pattern directly on the 3-D printed dielectric surface and then applying ink with a suitable tool. This approach is tested in combination with stereolithography 3-D printing technology to obtain selectively metallized 3-D circuits. In particular, the “clear” resin from FormLab is utilized for the 3-D printed dielectric, while the metallization is performed with silver nanoparticle ink from Suntronic. As a preliminary study, test samples containing lines with different widths are manufactured, demonstrating a pitch down to 135 μm and satisfactory sheet resistance of 0.011 Q/sq. (the electromagnetic characterization of the dielectric resin is reported in the Appendix). Then, two broadband multiport RF structures are developed to show the versatility of the proposed technology. First, an ultrawideband 3-D crossover, operating in the range 100 MHz-5 GHz, is conceived to test the suitability of the proposed technology to perform selective metallization on curved semi-enclosed areas. Then, the technology is applied to a multiple-input-multiple-output (MIMO) antenna system, based on four proximity-fed annular slot antennas, arranged on the lateral sides of a cube and decoupled by introducing a cross-shaped structure in the interior of the cube. This circuit offers a broad range of metallization challenges, as it features embossed and engraved parts, high-resolution patterns (line widths down to 0.7 mm) and sharp edges. Each slot radiates unidirectionally with the same polarization and uses the cube and its internal cross-shaped structure as a resonant cavity. The antenna system is designed to operate in the band 3.4-3.8 GHz, which is one of the sub-6-GHz 5G bands in Europe, and it is thought for hotspot and access-point applications. The final antenna topology is composed of only two blocks, weighs 21.29 g, and occupies a volume of 44.4 × 45.8 × 45.8 mm 3 , featuring an envelope correlation coefficient (ECC) lower than 0.005 and a total active reflection coefficient (TARC) lower than -6 dB in all the bands of interests.
- 27 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (7) , 1434-1447
3-D-Printing-Based Selective-Ink-Deposition Technique Enabling Complex Antenna and RF Structures for 5G Applications up to 6 GHz
This paper introduces a novel additivemanufacturing technique to obtain high-resolution selective-ink-deposition on complex 3-D objects, packages, and modules for 5G applications. The technique consists of embossing the desired pattern directly on the 3-D printed dielectric surface and then applying ink with a suitable tool. This approach is tested in combination with stereolithography 3-D printing technology to obtain selectively metallized 3-D circuits. In particular, the “clear” resin from FormLab is utilized for the 3-D printed dielectric, while the metallization is performed with silver nanoparticle ink from Suntronic. As a preliminary study, test samples containing lines with different widths are manufactured, demonstrating a pitch down to 135 μm and satisfactory sheet resistance of 0.011 Q/sq. (the electromagnetic characterization of the dielectric resin is reported in the Appendix). Then, two broadband multiport RF structures are developed to show the versatility of the proposed technology. First, an ultrawideband 3-D crossover, operating in the range 100 MHz-5 GHz, is conceived to test the suitability of the proposed technology to perform selective metallization on curved semi-enclosed areas. Then, the technology is applied to a multiple-input-multiple-output (MIMO) antenna system, based on four proximity-fed annular slot antennas, arranged on the lateral sides of a cube and decoupled by introducing a cross-shaped structure in the interior of the cube. This circuit offers a broad range of metallization challenges, as it features embossed and engraved parts, high-resolution patterns (line widths down to 0.7 mm) and sharp edges. Each slot radiates unidirectionally with the same polarization and uses the cube and its internal cross-shaped structure as a resonant cavity. The antenna system is designed to operate in the band 3.4-3.8 GHz, which is one of the sub-6-GHz 5G bands in Europe, and it is thought for hotspot and access-point applications. The final antenna topology is composed of only two blocks, weighs 21.29 g, and occupies a volume of 44.4 × 45.8 × 45.8 mm 3 , featuring an envelope correlation coefficient (ECC) lower than 0.005 and a total active reflection coefficient (TARC) lower than -6 dB in all the bands of interests.
- Open Access
- 7 October 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 35111
Fully inkjet-printed microfluidics: a solution to low-cost rapid three-dimensional microfluidics fabrication with numerous electrical and sensing applications
As the needs for low-cost rapidly-produced microfluidics are growing with the trend of Lab-on-a-Chip and distributed healthcare, the fully inkjet-printing of microfluidics can be a solution to it with numerous potential electrical and sensing applications. Inkjet-printing is an additive manufacturing technique featuring no material waste and a low equipment cost. Moreover, similar to other additive manufacturing techniques, inkjet-printing is easy to learn and has a high fabrication speed, while it offers generally a great planar resolution down to below 20 µm and enables flexible designs due to its inherent thin film deposition capabilities. Due to the thin film feature, the printed objects also usually obtain a high vertical resolution (such as 4.6 µm). This paper introduces a low-cost rapid three-dimensional fabrication process of microfluidics, that relies entirely on an inkjet-printer based single platform and can be implemented directly on top of virtually any substrates.
- 7 October 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 35111
Open AccessFully inkjet-printed microfluidics: a solution to low-cost rapid three-dimensional microfluidics fabrication with numerous electrical and sensing applications
As the needs for low-cost rapidly-produced microfluidics are growing with the trend of Lab-on-a-Chip and distributed healthcare, the fully inkjet-printing of microfluidics can be a solution to it with numerous potential electrical and sensing applications. Inkjet-printing is an additive manufacturing technique featuring no material waste and a low equipment cost. Moreover, similar to other additive manufacturing techniques, inkjet-printing is easy to learn and has a high fabrication speed, while it offers generally a great planar resolution down to below 20 µm and enables flexible designs due to its inherent thin film deposition capabilities. Due to the thin film feature, the printed objects also usually obtain a high vertical resolution (such as 4.6 µm). This paper introduces a low-cost rapid three-dimensional fabrication process of microfluidics, that relies entirely on an inkjet-printer based single platform and can be implemented directly on top of virtually any substrates.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 159-161
Additive manufacturing technologies for near-and far-field energy harvesting applications
This paper reviews the fabrication and design of two different types of energy harvesting systems, that utilize ambient energy to power up connected wireless modules. A 3D/inkjet-printed origami-style (morphing) cube with orthogonally-placed patch antennas is presented which enhances the nodes diversity reception capabilities. The cube changes its shape upon heating up to 60°C. In contrast, the presented near-field energy harvester utilizes the ambient RF energy of a handheld two-way radio to convert the RF signal with an efficiency of 82.5%. For proof-of-concept purposes, an E-field energy harvesting receiver is fabricated on a flexible LCP substrate with inkjet printing technology featuring an open-circuit voltage of 17.87V for an output power of 43.2 mW for the E-field energy harvester placed 7 cm away from a 1W Walkie-Talkie transmitter.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 159-161
Additive manufacturing technologies for near-and far-field energy harvesting applications
This paper reviews the fabrication and design of two different types of energy harvesting systems, that utilize ambient energy to power up connected wireless modules. A 3D/inkjet-printed origami-style (morphing) cube with orthogonally-placed patch antennas is presented which enhances the nodes diversity reception capabilities. The cube changes its shape upon heating up to 60°C. In contrast, the presented near-field energy harvester utilizes the ambient RF energy of a handheld two-way radio to convert the RF signal with an efficiency of 82.5%. For proof-of-concept purposes, an E-field energy harvesting receiver is fabricated on a flexible LCP substrate with inkjet printing technology featuring an open-circuit voltage of 17.87V for an output power of 43.2 mW for the E-field energy harvester placed 7 cm away from a 1W Walkie-Talkie transmitter.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Inkjet-printed dual microfluidic-based sensor integrated system
Demonstrated is a novel method to the fabrication of microfluidic devices utilizing a dual-sensor approach. The fabrication incorporates the use of poly(methyl-methacrylate) (PMMA) and inkjet-printing techniques. PMMA, a low-cost, robust material with low dielectric loss, is ideal for sensor fabrication. In addition, inkjet-printing polymer (SU-8) as a bonding layer dramatically improves the bonding strength and pressure handling. Furthermore, this system integrates two independent sensors in the same circuit, enabling concurrent calibration of two fluids. Based on the reaction in one sensor, response in another sensor for the same fluid can be predicted. The two sensors both have a sensitivity over 21 %/log(r) and a good independence in calibrating fluids. The sensor system works at microwave frequency, enabling applications in wireless sensing including various chemical analysis.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Inkjet-printed dual microfluidic-based sensor integrated system
Demonstrated is a novel method to the fabrication of microfluidic devices utilizing a dual-sensor approach. The fabrication incorporates the use of poly(methyl-methacrylate) (PMMA) and inkjet-printing techniques. PMMA, a low-cost, robust material with low dielectric loss, is ideal for sensor fabrication. In addition, inkjet-printing polymer (SU-8) as a bonding layer dramatically improves the bonding strength and pressure handling. Furthermore, this system integrates two independent sensors in the same circuit, enabling concurrent calibration of two fluids. Based on the reaction in one sensor, response in another sensor for the same fluid can be predicted. The two sensors both have a sensitivity over 21 %/log(r) and a good independence in calibrating fluids. The sensor system works at microwave frequency, enabling applications in wireless sensing including various chemical analysis.