MAMatthew P. Adams

Matthew P. Adams

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Matthew P. Adams has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Freeze–Thaw Cycling on the Mechanical and Durability Properties of Rapid Repair-Based Overlay Systems

    by Noah A. Thibodeaux, Maruf Hasan, Matthew J. Bandelt, Matthew P. Adams

    Rapid repair materials (RRMs) have been used in concrete overlay systems to rehabilitate infrastructure for many years. The bond performance between RRMs and a concrete substrate is crucial for maintaining the desired performance and can deteriorate due to freeze–thaw action. In the case of partial depth repairs (PDRs), the mechanical and durability properties at the interface between the substrate and repair materials have not been thoroughly studied resulting in frequent failures. There is limited research on the freeze–thaw durability of RRM overlay–substrate interface, and no standardized test methods exist for evaluating the performance under freeze–thaw cycling. The proposed experimental procedure combines freeze–thaw cycling of an overlay–substrate specimen with pull-off testing of the overlay. Three RRM overlay systems were used consisting of calcium sulfoaluminate cement and ordinary Portland cement (PC), and a ternary blend of PC, calcium aluminate cement, and calcium sulfate cement. A correlation between tensile bond strength and fundamental transverse frequency in composite specimens was observed, and the results demonstrated that RRMs can maintain robust adhesion following 300 cycles of freeze–thaw exposure. Furthermore, the employed testing methodology elicited bond-only failures, underscoring the necessity for continued investigation into optimal conditioning intervals and substrate integrity to enhance the durability of repair systems.


  • Open Access

    Service Life Prediction of RC and UHPC Bridge Decks Exposed to Regional Environments

    by Jin Fan, Matthew Adams, Matthew Bandelt

    The work presented in this paper is an investigation of bridge deck deterioration after exposure to regional environmental conditions and traffic loading. The service life of a set of bridge decks containing UHPC and normal strength reinforced concrete were studied through a twodimensional modeling technique that couples harmful material transport processes and structural deterioration in a time dependent manner. Regional environmental characteristics, such as periodically applying de-icing salts (chloride ions) and realistic local temperature fluctuations were considered in the simulations. Furthermore, mechanical damage induced by bridge deck traffic loading was considered in the chloride diffusion modeling approach. The simulation results show that the normal strength reinforced concrete bridge deck had cracks under traffic loading, while the reinforced UHPC bridge deck showed no observable damage at the same loading level. As such, the UHPC bridge deck had slower chloride penetration. Simulated chloride profiles confirmed that the material ingress process was influenced by the variation of temperature and deicing material concentrations. The normal strength reinforced concrete bridge deck experienced corrosion induced cracking and delamination under the combined effects of sustained traffic loading and regional environmental conditioning. In contrast, the reinforced UHPC bridge deck was sound and intact even after a much longer exposure time.


  • Open Access

    Strategic model reduction by analysing model sloppiness: a case study in coral calcification

    by Sarah A. Vollert, Christopher Drovandi, Gloria M. Monsalve-Bravo, Matthew P. Adams

    It can be difficult to identify ways to reduce the complexity of large models whilst maintaining predictive power, particularly where there are hidden parameter interdependencies. Here, we demonstrate that the analysis of model sloppiness can be a new invaluable tool for strategically simplifying complex models. Such an analysis identifies parameter combinations which strongly and/or weakly inform model behaviours, yet the approach has not previously been used to inform model reduction. Using a case study on a coral calcification model calibrated to experimental data, we show how the analysis of model sloppiness can strategically inform model simplifications which maintain predictive power. Additionally, when comparing various approaches to analysing sloppiness, we find that Bayesian methods can be advantageous when unambiguous identification of the best-fit model parameters is a challenge for standard optimisation procedures.

  • Open Access

    Effect of Cold Plasma Treatment of Polymer Fibers on the Mechanical Behavior of Fiber-Reinforced Cementitious Composites

    by Noah Thibodeaux, Daniel E. Guerrero, Jose L. Lopez, Matthew J. Bandelt, Matthew P. Adams

    Fiber-reinforced cementitious composites (FRCC) are a class of materials made by adding randomly distributed fibers to a cementitious matrix, providing better material toughness through the crack bridging behavior of the fibers. One of the primary concerns with FRCCs is the behavior of the fiber when a crack is formed. The fibers provide a stress-bridging mechanism, which is largely determined by the bond that exists between the concrete and the fiber’s outer surface. While many studies have determined the properties of FRCCs and potential benefits of using specific fiber types, the effects of low temperature or cold plasma treatment of polymer fibers on the mechanical behavior of the composite material are limited. Polymer fibers are notable for their low density, ductility, ease of manufacture, and cost-effectiveness. Despite these advantages, the surface properties of polymers do not enable the bonding potential given by steel or glass fibers when used in untreated FRCC, resulting in pull-out failures before the full displacement capacity of the fiber is utilized. For this reason, modification of the surface characteristics of polymer fibers can aid in higher bonding potential. Plasma treatment is a process wherein surfaces are modified through the kinetics of electrically charged and reactive species in a gaseous discharge environment. This paper is a preliminary study on the use of atmospheric pressure plasma generated at approximately room temperature. This atmospheric, cold plasma treatment is a method for improving the mechanical properties of FRCC using polymeric fibers. In this study, polypropylene and polyvinyl-alcohol fibers were cold plasma treated for 0, 30, 60, and 120 s before being used in cementitious mortar mixtures. Compression and flexure tests were performed using a displacement-based loading protocol to examine the impact of plasma treatment time on the corresponding mechanical performance of the fiber-reinforced cementitious composite. The experimental results obtained from this study indicate that there is a positive correlation between fiber treatment time and post-peak load-carrying capacity, especially for specimens subjected to flexural loading.


  • Using Supplementary Cementitious Materials to Mitigate Alkali-Silica Reaction in Concrete with Recycled-Concrete Aggregate

    by Matthew P. Adams, Jason H. Ideker

    Recycled concrete aggregate (RCA) is a key tool for improving sustainability in the construction and demolition industries. The use of RCA in new concrete is, in part, obstructed by the dearth of research available on the durability of RCA systems. This paper investigates the efficacy of replacing portland cement with supplementary cementitious materials (SCM), known to mitigate alkali-silica reaction (ASR) in concrete with virgin aggregates, as a method for reducing expansions related to ASR from reactive RCA. Fly ash (Class F), silica fume, and metakaolin were all investigated for their ability to mitigate ASR. The results of modified accelerated mortar bar tests are presented for two different RCAs when using 100% portland cement, binary blends of portland cement and fly ash, and ternary blends of portland cement, fly ash, and either metakaolin or silica fume. The results indicated that SCM can mitigate ASR in concrete made with RCA, though not as effectively as for natural aggregate systems. Higher levels of mitigation may be required for some RCAs, compared to the level necessary to mitigate or prevent ASR in concrete made with the original aggregates, depending on composition of the RCA.


  • Generation and Numerical Analysis of Random Aggregate Structures in Recycled Concrete Aggregate Systems

    by Anuruddha Jayasuriya, Matthew P. Adams, Matthew J. Bandelt

    A computational modeling procedure for generating a random aggregate structure (RAS) for recycled concrete aggregate (RCA) materials is proposed in this paper. The two-dimensional aggregate generation was based on a convex hull algorithm to randomize arbitrary planar shapes of RCA particles. During the generation of RAS, randomizations of the maximum aggregate size and spatial distribution of RCA particles were considered. Finite-element models for RCA systems were generated based on an extensive image analysis procedure. Numerical analyses were performed for 12 different RCA systems including crushed-shape and rounded-shape aggregates by varying the morphological parameters of the RCA particles. The mechanical performance of RCA systems with different particle shapes, maximum aggregate sizes, adhered mortar content levels, and aggregate ratios were used as factors to evaluate the mechanical performance of RCA systems under simulated compressive loading. Numerical results were compared with experimental studies from a large statistical database. The numerical simulation results for the mechanical properties of RCA systems showed represented experimental behavior such as the simulated elastic moduli and compressive strengths were within one and two standard deviations, respectively, of experimental results from a robust data set obtained through a detailed literature investigation. The proposed aggregate generation approach and numerical simulation procedure can be used by researchers to better understand how aggregate morphological properties influence the mechanical behavior of concrete made with recycled aggregates.