Akanksha Tyagi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Akanksha Tyagi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Vishwas Abhimanyu Sawant
Department of Civil Engineering, Indian Institute of Technology Roorkee, Roorkee, India
5 shared publications - Manisha Yadav
Indian Institute of Technology Roorkee
4 shared publications - Fook-Hou Lee
National Univ. of Singapore
3 shared publications - Murapaka Swamynaidu
Department of Civil Engineering, Indian Institute of Technology Roorkee, Roorkee, India
3 shared publications Sudipta Sarkar
Indian Institute of Technology Roorkee
3 shared publicationsYatesh Thakur
Indian Institute of Technology Roorkee
3 shared publications
Latest Publications
- 28 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Shaking-table tests on the liquefaction-induced behaviour of a shallow rectangular tunnel under varying groundwater levels
- 28 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Shaking-table tests on the liquefaction-induced behaviour of a shallow rectangular tunnel under varying groundwater levels
- 27 October 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Engineering Sustainability
- p. 1-18
Freeze-thaw durability of clays treated with cement, slag and alkali-activated fly ash
This research examines the performance of cement-, cement-ground granulated blast furnace slag (GGBFS)-, and fly ash cement alkali-activated (FCAA)-stabilised high plastic clays by measuring mass loss, strength loss, and stress–strain behaviour under the impact of freeze–thaw (F–T) durability cycles. Twelve F–T cycles were conducted at freezing and thawing temperatures of −20°C and 20°C, respectively. For both the cement- and cement-GGBFS-stabilised clay mixes, the mass loss increased with the increase in F–T cycles, with a higher reduction rate up to 6 or 9 F–T cycles. Unconfined compressive strength (UCS) values reduced from the 1st to 6th F–T cycles, beyond which the values did not change significantly with additional F–T cycles. Final UCS at the end of the 12th F–T cycle for the cement-GGBFS-stabilised clays with 30% binder content and 50% GGBFS replacement was higher than 500 kPa. The mass loss and UCS measurements for most of the FCAA-stabilised clay mixes could not be recorded after the 1st F–T cycle because of the breakage of samples, indicative of insufficient durability. The results are helpful for adopting a suitable alternative binder for in situ ground improvement techniques such as deep soil mixing and jet grouting for stabilising high plastic clays in seasonally frozen zones.
- 27 October 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Engineering Sustainability
- p. 1-18
Freeze-thaw durability of clays treated with cement, slag and alkali-activated fly ash
This research examines the performance of cement-, cement-ground granulated blast furnace slag (GGBFS)-, and fly ash cement alkali-activated (FCAA)-stabilised high plastic clays by measuring mass loss, strength loss, and stress–strain behaviour under the impact of freeze–thaw (F–T) durability cycles. Twelve F–T cycles were conducted at freezing and thawing temperatures of −20°C and 20°C, respectively. For both the cement- and cement-GGBFS-stabilised clay mixes, the mass loss increased with the increase in F–T cycles, with a higher reduction rate up to 6 or 9 F–T cycles. Unconfined compressive strength (UCS) values reduced from the 1st to 6th F–T cycles, beyond which the values did not change significantly with additional F–T cycles. Final UCS at the end of the 12th F–T cycle for the cement-GGBFS-stabilised clays with 30% binder content and 50% GGBFS replacement was higher than 500 kPa. The mass loss and UCS measurements for most of the FCAA-stabilised clay mixes could not be recorded after the 1st F–T cycle because of the breakage of samples, indicative of insufficient durability. The results are helpful for adopting a suitable alternative binder for in situ ground improvement techniques such as deep soil mixing and jet grouting for stabilising high plastic clays in seasonally frozen zones.
- 24 October 2026
- Published by Springer Nature
- p. 74-81
Extreme Temperature Effects on Strength Behaviour of Slag-Cement Stabilized Himalayan River Borne Material
- 24 October 2026
- Published by Springer Nature
- p. 74-81
Extreme Temperature Effects on Strength Behaviour of Slag-Cement Stabilized Himalayan River Borne Material
- 11 May 2026
- Published by Springer Nature in Sādhanā
- Vol. 51 (2) , 124
Barrier walls to mitigate tunnelling-induced settlement: A review
- 11 May 2026
- Published by Springer Nature in Sādhanā
- Vol. 51 (2) , 124
Barrier walls to mitigate tunnelling-induced settlement: A review
- 1 May 2026
- Published by Springer Nature
- p. 119-130
Stability of Lateritic Soil Cutting of Maharashtra Subjected to Rainfall Infiltration
- 1 May 2026
- Published by Springer Nature
- p. 119-130
Stability of Lateritic Soil Cutting of Maharashtra Subjected to Rainfall Infiltration
- 2 April 2026
- Published by Elsevier in Reliability Engineering & System Safety
- Vol. 275
Deterministic and probabilistic stability analyses of single tunnel in a cohesive-frictional finite slope
- 2 April 2026
- Published by Elsevier in Reliability Engineering & System Safety
- Vol. 275
Deterministic and probabilistic stability analyses of single tunnel in a cohesive-frictional finite slope