Jose Luis de Miguel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jose Luis de Miguel has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
M. C. Tamargo
Bellcore, 331 Newman Springs Road, Red Bank, New Jersey 07701
18 shared publicationsR. E. Nahory
Bellcore, 331 Newman Springs Road, Red Bank, New Jersey 07701
8 shared publicationsH. H. Farrell
Bellcore, 331 Newman Springs Road, Red Bank, New Jersey 07701
7 shared publicationsM.-H. Meynadier
6 shared publicationsD. M. Hwang
Bellcore, 331 Newman Springs Road, Red Bank, New Jersey 07701
5 shared publications- B. J. Skromme
Department of Electrical Engineering and Center for Solid State Electronics Research, Arizona State University, Tempe, AZ 85287-5706, USA
4 shared publications
Latest Publications
- Open Access
Experimental Demonstration of Low-Uncertainty Calibration Methods for Bragg Grating Interrogators
In this paper we propose and demonstrate two alternative methods for the high-precision calibration of fiber Bragg grating (FBG) interrogators. The first method is based on the direct comparison between the wavelength measurements of the interrogator under test and a calibrated wavemeter, while analyzing a simulated symmetric Bragg grating constructed by a tunable filter and a fiber mirror. This first method is applicable to most commercial systems but presents an uncertainty limited by the spectral width and the wavelength stability of the tunable filter. The second method consists in measuring multiple reference absorption lines of calibrated absorption gas cells. This second method presents lower uncertainties, limited only by the optical resolution of the interrogator and the wavelength uncertainty of the reference cell absorption lines. However, it imposes more restrictive requirements on the interrogator software. Both methods were experimentally demonstrated by calibrating multiple commercial systems, reaching uncertainties down to 0.63 pm at a central wavelength of 1550 nm.
Open AccessExperimental Demonstration of Low-Uncertainty Calibration Methods for Bragg Grating Interrogators
In this paper we propose and demonstrate two alternative methods for the high-precision calibration of fiber Bragg grating (FBG) interrogators. The first method is based on the direct comparison between the wavelength measurements of the interrogator under test and a calibrated wavemeter, while analyzing a simulated symmetric Bragg grating constructed by a tunable filter and a fiber mirror. This first method is applicable to most commercial systems but presents an uncertainty limited by the spectral width and the wavelength stability of the tunable filter. The second method consists in measuring multiple reference absorption lines of calibrated absorption gas cells. This second method presents lower uncertainties, limited only by the optical resolution of the interrogator and the wavelength uncertainty of the reference cell absorption lines. However, it imposes more restrictive requirements on the interrogator software. Both methods were experimentally demonstrated by calibrating multiple commercial systems, reaching uncertainties down to 0.63 pm at a central wavelength of 1550 nm.
- 1 May 1995
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 7 (5) , 546-548
Compressive strained multiquantum-well waveguide photodetectors for coherent receivers
Waveguide photodetectors (1.5 /spl mu/m) for polarization diversity coherent receivers have been fabricated on InP and characterized. They make use of the properties of multiquantum wells (MQW) to detect separately the TE and the TM polarized light. Diversity detection is achieved without the use of a polarization splitter or polarization controllers. The structure is compatible with the fabrication of DBR lasers and guided devices, so it is well suited for integration with other devices in the same chip.
- 1 May 1995
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 7 (5) , 546-548
Compressive strained multiquantum-well waveguide photodetectors for coherent receivers
Waveguide photodetectors (1.5 /spl mu/m) for polarization diversity coherent receivers have been fabricated on InP and characterized. They make use of the properties of multiquantum wells (MQW) to detect separately the TE and the TM polarized light. Diversity detection is achieved without the use of a polarization splitter or polarization controllers. The structure is compatible with the fabrication of DBR lasers and guided devices, so it is well suited for integration with other devices in the same chip.
- 1 October 1993
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 5 (10) , 1224-1227
Useful formulas for multimode interference power splitter/combiner design
Simple design formulas for optical power splitters with an arbitrary number of output ports (1*N) are presented. They are obtained using a model based on the interference of the confined modes of a multimode wide section. These formulas provide the correct dimensions of the device, plus the output phase relations and output guides location. The accuracy of these formulas is further demonstrated by the design and fabrication of a buried heterostructure waveguide power splitter on InP, compatible with laser integration, that yield compact and low insertion losses devices.<>
- 1 October 1993
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 5 (10) , 1224-1227
Useful formulas for multimode interference power splitter/combiner design
Simple design formulas for optical power splitters with an arbitrary number of output ports (1*N) are presented. They are obtained using a model based on the interference of the confined modes of a multimode wide section. These formulas provide the correct dimensions of the device, plus the output phase relations and output guides location. The accuracy of these formulas is further demonstrated by the design and fabrication of a buried heterostructure waveguide power splitter on InP, compatible with laser integration, that yield compact and low insertion losses devices.<>
- 16 February 1993
- Published by SPIE-Intl Soc Optical Eng
- Vol. 1788, 145-151
Dual pin photodetector with very low parasitic series interconnection
A dual back-illuminated photodetector for balanced coherent receivers applications is presented. The photodetectors have an InP/InGaAs/InP p-i-n structure. Several additional semiconductor layers have been added to fabricate the structure by selective wet etching. The material was grown by metalorganic vapor phase epitaxy (MOVPE) on a semiinsulating, Fe doped, InP substrate. The passivation and the insulation between contacts were obtained using polyimide. The contact structure is intended to connect the photodetector to the package by flip-chip. The measured photodetector capacitance was around 0.2 pF for a single photodetector (without series connection), the series resistance under 20 ohms, and the dark current under 10 nA.© (1993) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
- 16 February 1993
- Published by SPIE-Intl Soc Optical Eng
- Vol. 1788, 145-151
Dual pin photodetector with very low parasitic series interconnection
A dual back-illuminated photodetector for balanced coherent receivers applications is presented. The photodetectors have an InP/InGaAs/InP p-i-n structure. Several additional semiconductor layers have been added to fabricate the structure by selective wet etching. The material was grown by metalorganic vapor phase epitaxy (MOVPE) on a semiinsulating, Fe doped, InP substrate. The passivation and the insulation between contacts were obtained using polyimide. The contact structure is intended to connect the photodetector to the package by flip-chip. The measured photodetector capacitance was around 0.2 pF for a single photodetector (without series connection), the series resistance under 20 ohms, and the dark current under 10 nA.© (1993) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
- 15 May 1991
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 69 (10) , 7021-7028
‘‘Designer’’ interfaces in II-VI/III-V polar heteroepitaxy
The development of composite materials incorporating both II-VI and III-V compound semiconductors, such as ZnSe and GaAs, leads to the possibility of a variety of new devices of potential importance to the communications industry. In many cases, such as those involving resonant tunneling junctions and quantum well structures, the quality of the interface between the different compound semiconductors determines the ultimate quality of the device itself. Therefore, we have investigated the factors determining this interface quality for the GaAs/ZnSe system as prepared by molecular beam epitaxy. In this system, the stoichiometry of the substrate is of paramount importance. An excess of one constituent leads to high local electrical fields and poor interface morphology. Optimum growth of ZnSe on GaAs is achieved with GaAs substrate surfaces having a stoichiometry intermediate between the As- and Ga-rich extremes. We will describe a model that defines the conditions for good interface formation and summarize experimental evidence which supports the validity of this model.
- 15 May 1991
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 69 (10) , 7021-7028
‘‘Designer’’ interfaces in II-VI/III-V polar heteroepitaxy
The development of composite materials incorporating both II-VI and III-V compound semiconductors, such as ZnSe and GaAs, leads to the possibility of a variety of new devices of potential importance to the communications industry. In many cases, such as those involving resonant tunneling junctions and quantum well structures, the quality of the interface between the different compound semiconductors determines the ultimate quality of the device itself. Therefore, we have investigated the factors determining this interface quality for the GaAs/ZnSe system as prepared by molecular beam epitaxy. In this system, the stoichiometry of the substrate is of paramount importance. An excess of one constituent leads to high local electrical fields and poor interface morphology. Optimum growth of ZnSe on GaAs is achieved with GaAs substrate surfaces having a stoichiometry intermediate between the As- and Ga-rich extremes. We will describe a model that defines the conditions for good interface formation and summarize experimental evidence which supports the validity of this model.
- 1 May 1991
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 3 (5) , 418-420
Short-cavity distributed Bragg reflector laser with an integrated tapered output waveguide
A distributed Bragg reflector strained-layer multiple-quantum-well laser at 1.5- mu m wavelength with an integrated tapered waveguide beam expander is discussed. The far-field FWHMs in the lateral and vertical directions are 10 and 15 degrees , respectively. A quantum efficiency of 17% out the tapered facet was measured with a corresponding threshold current of 28 mA. The alignment tolerances for coupling into a cleaved single-mode fiber are 9.5 and 7.5 mu m FWHM in the lateral and vertical directions, respectively. A 3-dB improvement for single-mode fiber coupling using a SELFOC lens was obtained.
- 1 May 1991
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 3 (5) , 418-420
Short-cavity distributed Bragg reflector laser with an integrated tapered output waveguide
A distributed Bragg reflector strained-layer multiple-quantum-well laser at 1.5- mu m wavelength with an integrated tapered waveguide beam expander is discussed. The far-field FWHMs in the lateral and vertical directions are 10 and 15 degrees , respectively. A quantum efficiency of 17% out the tapered facet was measured with a corresponding threshold current of 28 mA. The alignment tolerances for coupling into a cleaved single-mode fiber are 9.5 and 7.5 mu m FWHM in the lateral and vertical directions, respectively. A 3-dB improvement for single-mode fiber coupling using a SELFOC lens was obtained.
- Open Access
- 28 February 1991
- Published by Elsevier in Journal of Luminescence
- Vol. 48-49, 731-734
Type II indirect gap superlattices under intense optical excitation
- 28 February 1991
- Published by Elsevier in Journal of Luminescence
- Vol. 48-49, 731-734
Open AccessType II indirect gap superlattices under intense optical excitation
- 18 February 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 58 (7) , 780
Erratum: Electric field screening by photogenerated holes in multiple quantum wells: A new mechanism for absorption saturation [Appl. Phys. Lett. 57, 1081 (1990)]
- 18 February 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 58 (7) , 780
Erratum: Electric field screening by photogenerated holes in multiple quantum wells: A new mechanism for absorption saturation [Appl. Phys. Lett. 57, 1081 (1990)]
- 28 January 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 58 (4) , 355-357
Optimal GaAs(100) substrate terminations for heteroepitaxy
The quality of heteroepitaxial growth of II-VI materials on III-V substrates, such as ZnSe on GaAs(100), depends strongly on the atomic structure and stoichiometry of the substrate. We define and describe those structures that optimize heteroepitaxial interface growth on GaAs(100) and related surfaces, and propose specific models for the c(6×4), ‘‘3×1’’, (4×6), an As-lean version of the (2×4), and Se substitutional such as the (4×3). It is proposed that a good heteroepitaxial interface, with no extraneous fields and no charge imbalance, is achieved with substrate structures which lead directly to the appropriate interface stoichiometry.
- 28 January 1991
- Published by AIP Publishing in Applied Physics Letters
- Vol. 58 (4) , 355-357
Optimal GaAs(100) substrate terminations for heteroepitaxy
The quality of heteroepitaxial growth of II-VI materials on III-V substrates, such as ZnSe on GaAs(100), depends strongly on the atomic structure and stoichiometry of the substrate. We define and describe those structures that optimize heteroepitaxial interface growth on GaAs(100) and related surfaces, and propose specific models for the c(6×4), ‘‘3×1’’, (4×6), an As-lean version of the (2×4), and Se substitutional such as the (4×3). It is proposed that a good heteroepitaxial interface, with no extraneous fields and no charge imbalance, is achieved with substrate structures which lead directly to the appropriate interface stoichiometry.