Boris V. Sveshnikov
Research Subjects
Boris V. Sveshnikov has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
A.P. Shitvov
4 shared publicationsA. S. Bagdasaryan
P. N. Lebedev Center of Physical Studies
3 shared publicationsAleksey Koigerov
Saint Petersburg Electrotechnical University, St. Petersburg 198216, Russia
2 shared publications- Alexey Shitvov
Univ. College London (United Kingdom)
2 shared publications A. S.BAgdasaryan
P. N. Lebedev Center of Physical Studies
1 shared publicationK.K. Bhattacharjee
1 shared publication
Latest Publications
- 5 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 65 (11) , 2176-2183
Multitransducer SAW Device Architecture for Passive Wireless Sensor Tags
A new architecture of surface acoustic wave (SAW) sensor-tags with lower insertion loss and enhanced sensitivity is investigated. It efficiently employs two transducer arrays at the input and output of the acoustic channel, respectively. The improved sensitivity is attained due to a higher number of stronger constituent signals contributing constructively to the device response. An efficient matrix modeling approach is generalized to permit fast design and synthesis of the multitransducer sensor-tags with arbitrary topologies. The modeling approach consistency is validated by energy balance. Several simulation examples of new 6 GHz SAW sensor-tags, implemented on 128°YX-LiNbO3 substrate, are presented and compared against a conventional reflective delay line device. The effects of finite electrode resistivity and SAW beam diffraction are evaluated numerically and the SAW sensor-tag design tradeoffs and principles are established.
- 5 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 65 (11) , 2176-2183
Multitransducer SAW Device Architecture for Passive Wireless Sensor Tags
A new architecture of surface acoustic wave (SAW) sensor-tags with lower insertion loss and enhanced sensitivity is investigated. It efficiently employs two transducer arrays at the input and output of the acoustic channel, respectively. The improved sensitivity is attained due to a higher number of stronger constituent signals contributing constructively to the device response. An efficient matrix modeling approach is generalized to permit fast design and synthesis of the multitransducer sensor-tags with arbitrary topologies. The modeling approach consistency is validated by energy balance. Several simulation examples of new 6 GHz SAW sensor-tags, implemented on 128°YX-LiNbO3 substrate, are presented and compared against a conventional reflective delay line device. The effects of finite electrode resistivity and SAW beam diffraction are evaluated numerically and the SAW sensor-tag design tradeoffs and principles are established.
- 1 January 2018
- Published by Elsevier in Ultrasonics
- Vol. 82, 209-216
Unveiling the polarization of the multimode acoustic fields
- 1 January 2018
- Published by Elsevier in Ultrasonics
- Vol. 82, 209-216
Unveiling the polarization of the multimode acoustic fields
- 17 November 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (6) , 449-460
Generalized Discrete Model of Systems with Distributed Feedback Based on Surface Acoustic Waves
- 17 November 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (6) , 449-460
Generalized Discrete Model of Systems with Distributed Feedback Based on Surface Acoustic Waves
- 1 August 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (3) , 257
Erratum to: The Main Principles of Formation of the Transverse Modes in the Multilayered Waveguides of Surface Acoustic Waves
- 1 August 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (3) , 257
Erratum to: The Main Principles of Formation of the Transverse Modes in the Multilayered Waveguides of Surface Acoustic Waves
- 1 August 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (3) , 225-233
Scattering of the Transverse Waveguide Modes of Surface Acoustic Waves by the Finite-Aperture Electrode Structures
- 1 August 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (3) , 225-233
Scattering of the Transverse Waveguide Modes of Surface Acoustic Waves by the Finite-Aperture Electrode Structures
- 1 July 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (2) , 97-110
The Main Principles of Formation of the Transverse Modes in the Multilayered Waveguides of Surface Acoustic Waves
- 1 July 2016
- Published by Springer Nature in Radiophysics and Quantum Electronics
- Vol. 59 (2) , 97-110
The Main Principles of Formation of the Transverse Modes in the Multilayered Waveguides of Surface Acoustic Waves
- 19 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 83-85
Fundamental validation of the FEM based calculations concerning simulation of SAW and LSAW devices
A novel integral method is proposed to validate the simulation of devices based on surface (SAW) and leaky surface (LSAW) acoustic waves. This method requires the perfect satisfaction of the energy balance condition over the whole spectrum of analysis. It allows evaluating quantitatively the precision of calculations made using the software packages based on the finite element method (FEM).
- 19 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 83-85
Fundamental validation of the FEM based calculations concerning simulation of SAW and LSAW devices
A novel integral method is proposed to validate the simulation of devices based on surface (SAW) and leaky surface (LSAW) acoustic waves. This method requires the perfect satisfaction of the energy balance condition over the whole spectrum of analysis. It allows evaluating quantitatively the precision of calculations made using the software packages based on the finite element method (FEM).
- Open Access
- 29 August 2013
- Published by IntechOpen
On Universal Modeling of the Bulk Acoustic Wave Devices
On Universal Modeling of the Bulk Acoustic Wave Devices | InTechOpen, Published on: 2013-08-28. Authors: Boris Sveshnikov, Sergey Nikitov and Sergey Suchkov
- 29 August 2013
- Published by IntechOpen
Open AccessOn Universal Modeling of the Bulk Acoustic Wave Devices
On Universal Modeling of the Bulk Acoustic Wave Devices | InTechOpen, Published on: 2013-08-28. Authors: Boris Sveshnikov, Sergey Nikitov and Sergey Suchkov
- 1 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10510117,p. 1890-1893
Discrete analysis of regular systems
A novel technique is presented, allowing investigation of periodic interdigital transducers (IDTs) with better accuracy. Discrete analysis of regular systems (DARS) is based on the consistent approach demanding, as well as the Coupling-of Modes (COM) analysis, only the phenomenological knowledge of the reflection, transduction and attenuation coefficients per a grating pitch. Unlike the COM technique, dealing with the differential equations, a system of coupled difference equations (CDE) is applied now to describe the wave amplitudes at cross sections placed in the middle between neighbor pitches along an IDT. By solving CDE directly, one can find out all the desired terms of the transducer P-matrix in a very compact analytical form in the most general case.
- 1 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10510117,p. 1890-1893
Discrete analysis of regular systems
A novel technique is presented, allowing investigation of periodic interdigital transducers (IDTs) with better accuracy. Discrete analysis of regular systems (DARS) is based on the consistent approach demanding, as well as the Coupling-of Modes (COM) analysis, only the phenomenological knowledge of the reflection, transduction and attenuation coefficients per a grating pitch. Unlike the COM technique, dealing with the differential equations, a system of coupled difference equations (CDE) is applied now to describe the wave amplitudes at cross sections placed in the middle between neighbor pitches along an IDT. By solving CDE directly, one can find out all the desired terms of the transducer P-matrix in a very compact analytical form in the most general case.
- 1 September 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10510117,p. 1688-1690
SAW tags based on the self-matched unidirectional transducers
A use of self-matched unidirectional transducers (SMUDTs) is proposed in application to SAW tags. SMUDT provides simultaneously both high degree of its directionality and matching with the tag antenna without additional external circuitry. Numerical simulations of the tags, synthesized on 128° YX-LiNbO3, confirm an efficiency of the proposed technique.
- 1 September 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10510117,p. 1688-1690
SAW tags based on the self-matched unidirectional transducers
A use of self-matched unidirectional transducers (SMUDTs) is proposed in application to SAW tags. SMUDT provides simultaneously both high degree of its directionality and matching with the tag antenna without additional external circuitry. Numerical simulations of the tags, synthesized on 128° YX-LiNbO3, confirm an efficiency of the proposed technique.