Jan Loof
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jan Loof has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Henk Nijmeijer
Department of Mechanical Engineering, Eindhoven University of Technology, Eindhoven, Netherlands
1 shared publication- Henk Nijmeijer
Eindhoven University of Technology
1 shared publication - I. J. M. Besselink
Eindhoven University of Technology
1 shared publication Igo Besselink
Department of Mechanical Engineering, Eindhoven University of Technology, Eindhoven, Netherlands
1 shared publication
Latest Publications
- 28 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Vehicles
- Vol. 4 (4) , 578-587
Automated Lane Changing With a Controlled Steering-Wheel Feedback Torque for Low Lateral Acceleration Purposes
To bridge the gap between autonomous and normal steering during low lateral acceleration maneuvers, a steering-wheel torque controller is developed. It consists of three controllers in series, a high-gain feedback steering-wheel torque controller, a nonlinear steering-angle controller, and a linear yaw-rate controller. A validated two degrees of freedom steering-system model, in combination with a single-track vehicle model, is used to determine the controller parameters. Driving tests with different drivers have been executed to find a comfortable steering-wheel torque/angle relation. This relation is maintained throughout the lane change by specifying the steering-wheel torque as a function of the steering-wheel angle tracking error. Experiments show promising results regarding the driver/vehicle interaction, but also show that a system to detect the lanes and the vehicle position on the road is required for further improvement.
- 28 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Vehicles
- Vol. 4 (4) , 578-587
Automated Lane Changing With a Controlled Steering-Wheel Feedback Torque for Low Lateral Acceleration Purposes
To bridge the gap between autonomous and normal steering during low lateral acceleration maneuvers, a steering-wheel torque controller is developed. It consists of three controllers in series, a high-gain feedback steering-wheel torque controller, a nonlinear steering-angle controller, and a linear yaw-rate controller. A validated two degrees of freedom steering-system model, in combination with a single-track vehicle model, is used to determine the controller parameters. Driving tests with different drivers have been executed to find a comfortable steering-wheel torque/angle relation. This relation is maintained throughout the lane change by specifying the steering-wheel torque as a function of the steering-wheel angle tracking error. Experiments show promising results regarding the driver/vehicle interaction, but also show that a system to detect the lanes and the vehicle position on the road is required for further improvement.
- Open Access
- 14 March 2018
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 57 (1) , 86-107
Implementation and validation of a three degrees of freedom steering-system model in a full vehicle model
This paper describes the coupling between a three degrees of freedom steering-system model and a multi-body truck model. The steering-system model includes the king-pin geometry to provide the correct feedback torque from the road to the steering-system. The steering-system model is combined with a validated tractor semi-trailer model. An instrumented tractor semi-trailer has been tested on a proving ground and the steering-wheel torque, pitman-arm angle, king-pin angles and drag-link force have been measured during steady-state cornering, a step steer input and a sinusoidal steering input. It is shown that the steering-system model is able to accurately predict the steering-wheel torque for all tests and the vehicle model is accurate for vehicle motions up to a frequency where the lateral acceleration gain is minimum. Even though the vehicle response is not accurate above this frequency, the steering-wheel torque is still represented accurately.
- 14 March 2018
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 57 (1) , 86-107
Open AccessImplementation and validation of a three degrees of freedom steering-system model in a full vehicle model
This paper describes the coupling between a three degrees of freedom steering-system model and a multi-body truck model. The steering-system model includes the king-pin geometry to provide the correct feedback torque from the road to the steering-system. The steering-system model is combined with a validated tractor semi-trailer model. An instrumented tractor semi-trailer has been tested on a proving ground and the steering-wheel torque, pitman-arm angle, king-pin angles and drag-link force have been measured during steady-state cornering, a step steer input and a sinusoidal steering input. It is shown that the steering-system model is able to accurately predict the steering-wheel torque for all tests and the vehicle model is accurate for vehicle motions up to a frequency where the lateral acceleration gain is minimum. Even though the vehicle response is not accurate above this frequency, the steering-wheel torque is still represented accurately.