Shan Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shan Yin has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Guilin Wen
10 shared publicationsJinchen Ji
8 shared publicationsHuidong Xu
5 shared publications- Huidong Xu
College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan, China
4 shared publications Sijin Zhang
4 shared publicationsXin Wu
4 shared publications
Latest Publications
- Open Access
- 22 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (20)
Suppressing multiband Lamb wave propagation using surface-mounted curved elastic metasurfaces
Vibration control in engineering structures is a critical and common challenge. Acoustic metasurfaces offer a novel approach for vibration control by manipulating acoustic wave propagation. However, conventional designs for controlling wave propagation often require material removal, such as holes or slots, which compromise structural integrity and complicate fabrication. This study introduces a surface-mounted curved elastic metasurface that effectively suppresses Lamb wave propagation without modifying the base material, thereby preserving its mechanical strength. By modulating the transmission path and adjusting the phase of Lamb wave transmission, this design achieves significant vibration amplitude reduction through destructive interferences. Structural dimension optimization enhances wave suppression across thin plates and curved beams, providing broadband suppression across multiple frequency bands. This metasurface design holds broad potential for wave manipulation and advanced acoustic device development.
- 22 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (20)
Open AccessSuppressing multiband Lamb wave propagation using surface-mounted curved elastic metasurfaces
Vibration control in engineering structures is a critical and common challenge. Acoustic metasurfaces offer a novel approach for vibration control by manipulating acoustic wave propagation. However, conventional designs for controlling wave propagation often require material removal, such as holes or slots, which compromise structural integrity and complicate fabrication. This study introduces a surface-mounted curved elastic metasurface that effectively suppresses Lamb wave propagation without modifying the base material, thereby preserving its mechanical strength. By modulating the transmission path and adjusting the phase of Lamb wave transmission, this design achieves significant vibration amplitude reduction through destructive interferences. Structural dimension optimization enhances wave suppression across thin plates and curved beams, providing broadband suppression across multiple frequency bands. This metasurface design holds broad potential for wave manipulation and advanced acoustic device development.
- Open Access
- 1 July 2024
- Published by AIP Publishing in Chaos: An Interdisciplinary Journal of Nonlinear Science
- Vol. 34 (7)
An optimization approach to establish dynamical equivalence for soft and rigid impact models
This paper studies a computational approach aimed at establishing equivalent dynamical responses within oscillatory impacting systems subject to soft and rigid constraints. The proposed method incorporates an adaptive differential evolution algorithm with the Metropolis criterion to determine the stiffness and damping parameters of the soft constraint for a prescribed coefficient of restitution governing the rigid constraint. The proposed algorithm aims to establish an equivalent dynamical response of the two models based on constraints regarding energy dissipation and contact time duration. Upon examining the dynamical responses of the two impact cases, they exhibit nearly identical outcomes in the two-parameter bifurcation diagrams when subjected to a large restitution coefficient. However, discrepancies arise between the results of the two models when the restitution coefficient is low. Detailed numerical tests, conducted using the proposed method, demonstrate enhanced effectiveness compared to previous techniques, such as the prediction formulas for the different related soft impact model outlined by Okolewski and Blazejczyk-Okolewska [Chaos 31(8), 083110 (2021)]. This method not only finds application in experimentally identifying the physical properties of an impact surface but also provides convenience in employing soft models within impacting systems, which could then avoid potential inaccuracies in handling discontinuities by some integrator during velocity jumps before and after impacts.
- 1 July 2024
- Published by AIP Publishing in Chaos: An Interdisciplinary Journal of Nonlinear Science
- Vol. 34 (7)
Open AccessAn optimization approach to establish dynamical equivalence for soft and rigid impact models
This paper studies a computational approach aimed at establishing equivalent dynamical responses within oscillatory impacting systems subject to soft and rigid constraints. The proposed method incorporates an adaptive differential evolution algorithm with the Metropolis criterion to determine the stiffness and damping parameters of the soft constraint for a prescribed coefficient of restitution governing the rigid constraint. The proposed algorithm aims to establish an equivalent dynamical response of the two models based on constraints regarding energy dissipation and contact time duration. Upon examining the dynamical responses of the two impact cases, they exhibit nearly identical outcomes in the two-parameter bifurcation diagrams when subjected to a large restitution coefficient. However, discrepancies arise between the results of the two models when the restitution coefficient is low. Detailed numerical tests, conducted using the proposed method, demonstrate enhanced effectiveness compared to previous techniques, such as the prediction formulas for the different related soft impact model outlined by Okolewski and Blazejczyk-Okolewska [Chaos 31(8), 083110 (2021)]. This method not only finds application in experimentally identifying the physical properties of an impact surface but also provides convenience in employing soft models within impacting systems, which could then avoid potential inaccuracies in handling discontinuities by some integrator during velocity jumps before and after impacts.
- Open Access
Crystallization-Inspired Design and Modeling of Self-Assembly Lattice-Formation Swarm Robotics
Self-assembly formation is a key research topic for realizing practical applications in swarm robotics. Due to its inherent complexity, designing high-performance self-assembly formation strategies and proposing corresponding macroscopic models remain formidable challenges and present an open research frontier. Taking inspiration from crystallization, this paper introduces a distributed self-assembly formation strategy by defining free, moving, growing, and solid states for robots. Robots in these states can spontaneously organize into user-specified two-dimensional shape formations with lattice structures through local interactions and communications. To address the challenges posed by complex spatial structures in modeling a macroscopic model, this work introduces the structural features estimation method. Subsequently, a corresponding non-spatial macroscopic model is developed to predict and analyze the self-assembly behavior, employing the proposed estimation method and a stock and flow diagram. Real-robot experiments and simulations validate the flexibility, scalability, and high efficiency of the proposed self-assembly formation strategy. Moreover, extensive experimental and simulation results demonstrate the model’s accuracy in predicting the self-assembly process under different conditions. Model-based analysis indicates that the proposed self-assembly formation strategy can fully utilize the performance of individual robots and exhibits strong self-stability.
Open AccessCrystallization-Inspired Design and Modeling of Self-Assembly Lattice-Formation Swarm Robotics
Self-assembly formation is a key research topic for realizing practical applications in swarm robotics. Due to its inherent complexity, designing high-performance self-assembly formation strategies and proposing corresponding macroscopic models remain formidable challenges and present an open research frontier. Taking inspiration from crystallization, this paper introduces a distributed self-assembly formation strategy by defining free, moving, growing, and solid states for robots. Robots in these states can spontaneously organize into user-specified two-dimensional shape formations with lattice structures through local interactions and communications. To address the challenges posed by complex spatial structures in modeling a macroscopic model, this work introduces the structural features estimation method. Subsequently, a corresponding non-spatial macroscopic model is developed to predict and analyze the self-assembly behavior, employing the proposed estimation method and a stock and flow diagram. Real-robot experiments and simulations validate the flexibility, scalability, and high efficiency of the proposed self-assembly formation strategy. Moreover, extensive experimental and simulation results demonstrate the model’s accuracy in predicting the self-assembly process under different conditions. Model-based analysis indicates that the proposed self-assembly formation strategy can fully utilize the performance of individual robots and exhibits strong self-stability.
- Open Access
Approximation-free control based on the bioinspired reference model for suspension systems with uncertainty and unknown nonlinearity
Uncertainty and unknown nonlinearity are often inevitable in the suspension systems, which were often solved using fuzzy logic system (FLS) or neural networks (NNs). However, these methods are restricted by the structural complexity of the controller and the huge computing cost. Meanwhile, the estimation error of such approximators is affected by adopted adaptive laws and learning gains. Thus, in view of the above problem, this paper proposes the approximation-free control based on the bioinspired reference model for a class of uncertain suspension systems with unknown nonlinearity. The proposed method integrates the superior vibration suppression of the bioinspired reference model and the structural advantage of the prescribed performance function (PPF) in approximation-free control. Then, the vibration suppression performance is improved, the calculation burden is relieved, and the transient performance is improved, which is analyzed theoretically in this paper. Finally, the simulation results validate the approach, and the comparisons show the advantages of the proposed control method in terms of good vibration suppression, fast convergence, and less calculation burden.
Open AccessApproximation-free control based on the bioinspired reference model for suspension systems with uncertainty and unknown nonlinearity
Uncertainty and unknown nonlinearity are often inevitable in the suspension systems, which were often solved using fuzzy logic system (FLS) or neural networks (NNs). However, these methods are restricted by the structural complexity of the controller and the huge computing cost. Meanwhile, the estimation error of such approximators is affected by adopted adaptive laws and learning gains. Thus, in view of the above problem, this paper proposes the approximation-free control based on the bioinspired reference model for a class of uncertain suspension systems with unknown nonlinearity. The proposed method integrates the superior vibration suppression of the bioinspired reference model and the structural advantage of the prescribed performance function (PPF) in approximation-free control. Then, the vibration suppression performance is improved, the calculation burden is relieved, and the transient performance is improved, which is analyzed theoretically in this paper. Finally, the simulation results validate the approach, and the comparisons show the advantages of the proposed control method in terms of good vibration suppression, fast convergence, and less calculation burden.
- 1 April 2020
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 120
Novel two-parameter dynamics of impact oscillators near degenerate grazing points
- 1 April 2020
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 120
Novel two-parameter dynamics of impact oscillators near degenerate grazing points
- 17 March 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 234 (15) , 3116-3130
Fatigue life analysis of double-row tapered roller bearing in a modern wind turbine under oscillating external load and speed
Fatigue life analysis of roller bearing is usually performed for bearings under constant rotating speed and invariant loading conditions. For the bearings used in offshore floating direct-drive wind turbines, they often experience oscillating motions with varying loading patterns, for which the standard fatigue life analysis is not valid due to the presence of fluctuating loads. This paper presents the fatigue life analysis of a double-row tapered roller bearing under oscillating external load and speed conditions, which is used to support the main shaft of a large modern direct-drive wind turbine. First, a comprehensive quasi-static model of the double-row tapered roller bearing is developed for determining the internal load distribution of rollers. The contact pressure of rollers is then studied using an iterative scheme based on the elastic contact model. After that, the formulation of basic rating life of the double-row tapered roller bearing with oscillating external load and speed is given to calculate the fatigue life. Numerical simulations are carried out to investigate the effects of the oscillating load and speed, angular misalignment, and internal clearance on the fatigue life of the bearing.
- 17 March 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 234 (15) , 3116-3130
Fatigue life analysis of double-row tapered roller bearing in a modern wind turbine under oscillating external load and speed
Fatigue life analysis of roller bearing is usually performed for bearings under constant rotating speed and invariant loading conditions. For the bearings used in offshore floating direct-drive wind turbines, they often experience oscillating motions with varying loading patterns, for which the standard fatigue life analysis is not valid due to the presence of fluctuating loads. This paper presents the fatigue life analysis of a double-row tapered roller bearing under oscillating external load and speed conditions, which is used to support the main shaft of a large modern direct-drive wind turbine. First, a comprehensive quasi-static model of the double-row tapered roller bearing is developed for determining the internal load distribution of rollers. The contact pressure of rollers is then studied using an iterative scheme based on the elastic contact model. After that, the formulation of basic rating life of the double-row tapered roller bearing with oscillating external load and speed is given to calculate the fatigue life. Numerical simulations are carried out to investigate the effects of the oscillating load and speed, angular misalignment, and internal clearance on the fatigue life of the bearing.
- 7 January 2020
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 99 (4) , 2647-2656
Existence of invariant curves for a Fermi-type impact absorber
- 7 January 2020
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 99 (4) , 2647-2656
Existence of invariant curves for a Fermi-type impact absorber
- 1 January 2020
- Published by Elsevier in Tribology International
- Vol. 141
Internal loads and contact pressure distributions on the main shaft bearing in a modern gearless wind turbine
- 1 January 2020
- Published by Elsevier in Tribology International
- Vol. 141
Internal loads and contact pressure distributions on the main shaft bearing in a modern gearless wind turbine
- 23 September 2019
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 14 (11)
Multistability in the Centrifugal Governor System Under a Time-Delay Control Strategy
The centrifugal governor system plays an indispensable role in maintaining the near-constant speed of engines. Although different arrangements have been developed, the governor systems are still applied in many machines for its simple mechanical structure. Therefore, the large-amplitude vibrations of the governor system which can lead to the function failure of the system should be attenuated to guarantee reliable operation. This paper adopts a time-delay control strategy to suppress the undesirable large-amplitude motions in the centrifugal governor system, which can be regarded as the practical application of the delayed feedback controller in this system. The stability region of the trivial equilibrium of the controlled system is determined by investigating the characteristic equation and generic Hopf bifurcations. It is found that the dynamic behavior of multistability can be induced by the Bautin bifurcation, arising on the stability boundary of the trivial equilibrium with a constant delay. More specifically, a coexistence of two desirable stable motions, i.e., an equilibrium or a small-amplitude periodic motion, can be observed in the controlled centrifugal governor system without changing the physical parameters. This is a new feature of the motion control in the centrifugal governor systems, which has not yet been reported in the existing studies. Finally, the results of theoretical analyses are verified by numerical simulations.
- 23 September 2019
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 14 (11)
Multistability in the Centrifugal Governor System Under a Time-Delay Control Strategy
The centrifugal governor system plays an indispensable role in maintaining the near-constant speed of engines. Although different arrangements have been developed, the governor systems are still applied in many machines for its simple mechanical structure. Therefore, the large-amplitude vibrations of the governor system which can lead to the function failure of the system should be attenuated to guarantee reliable operation. This paper adopts a time-delay control strategy to suppress the undesirable large-amplitude motions in the centrifugal governor system, which can be regarded as the practical application of the delayed feedback controller in this system. The stability region of the trivial equilibrium of the controlled system is determined by investigating the characteristic equation and generic Hopf bifurcations. It is found that the dynamic behavior of multistability can be induced by the Bautin bifurcation, arising on the stability boundary of the trivial equilibrium with a constant delay. More specifically, a coexistence of two desirable stable motions, i.e., an equilibrium or a small-amplitude periodic motion, can be observed in the controlled centrifugal governor system without changing the physical parameters. This is a new feature of the motion control in the centrifugal governor systems, which has not yet been reported in the existing studies. Finally, the results of theoretical analyses are verified by numerical simulations.
- 1 June 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 156, 106-122
Complex near-grazing dynamics in impact oscillators
- 1 June 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 156, 106-122
Complex near-grazing dynamics in impact oscillators