ZWZhineng Wang

Zhineng Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhineng Wang has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Computational Fluid Dynamics–Population Balance Model (CFD–PBM) Study on the Performance and Bubble Evolution of an Air–water Airlift Pump

    by B. Duan, Z. Wang, H. Huang, G. Feng, F. Ye

    To investigate the coupled effects of submergence ratio and gas flow rate on the lifting performance and bubble evolution of a straight-pipe air–water airlift pump, a three-dimensional transient computational fluid dynamics model built upon the Eulerian–Eulerian two-fluid framework incorporated with a Population Balance Model (PBM) was developed and validated against experimental measurements. Over the ranges of submergence ratio of 0.3–0.7 and gas flow rate of 20–50 m³·h⁻¹, the variations in liquid flow rate, gas holdup, Sauter mean diameter, and mass lifting ratio were systematically examined. The results indicate that liquid flow rate generally increases with gas flow rate and submergence ratio, although its marginal increment diminishes significantly under high gas flow rate conditions. Gas holdup increases monotonically with gas flow rate, but such an increase fails to yield a continuous enhancement in liquid lifting capacity. The Sauter mean diameter initially decreases and subsequently increases with gas flow rate, reflecting the competing effects of bubble breakup and coalescence. The mass lifting ratio declines progressively with increasing gas flow rate but rises gradually with submergence ratio. Overall, submergence ratio serves as the fundamental driving force for system operation, whereas gas flow rate modulates two-phase transport by regulating the bubble swarm structure and the gas–liquid interfacial state. Proper matching of operating parameters is therefore critical for the synergistic optimization of lifting capacity and gas utilization efficiency.

  • Open Access

    Effect of die fillet radius on tube thinning in free bending

    by Yaochen Lin, Yunfeng Lin, Weiming Lin, Heng Liu, Shuyou Zhang, Zhineng Wang

    During the operation of a free-bending die, its fillets inevitably wear out, thereby reducing their “sharpness” and decreasing the forming accuracy of tubes. To clarify the influence law of fillet radius on the wall thickness of freely bent pipes, this study employs a combined approach of finite element simulation and experimental testing to systematically analyze the strain characteristics and wall thickness distribution of the pipes. The results indicate that the outer surface of the pipe exhibits the maximum thinning rate when the mold ceases upward movement. During the mold movement stage, increasing the fillet radius can mitigate tube wall thinning by expanding the contact area between the mold and the pipe. The thinnest region of the bent pipe is located at the end of the radius formation section, with a maximum thinning rate of 5.4%. Furthermore, an increase in mold offset distance, a rise in friction coefficient, and the adoption of thin-walled pipe structures all exacerbate the thinning phenomenon in this vulnerable region, which warrants special attention in engineering practice. With the increase of fillet radius, the maximum thinning rate presents a variation pattern of “first decreasing rapidly and then decreasing extremely slowly”. Within the range where the fillet radius-to-tube radius ratio (RB/r) is less than 0.33, the rate of decrease is significantly faster than that in the range where RB/r > 0.33. When RB/r = 0.33, a sudden enhancement of the thinning-inhibiting effect is observed. Subsequently, further increasing the fillet radius exerts no significant inhibitory effect on the maximum thinning rate. The findings of this study provide a theoretical basis and engineering guidance for the optimization of fillet parameters of free bending dies and the control of pipe forming accuracy.

  • The mechanism of compression and bending coupling effects on cross-sectional distortion under boosting conditions

    by Shuowen Shen, Zhineng Wang

    Push-Assist is commonly used to inhibit the thinning defect in the bending forming of aerospace tubes, but it tends to introduce distortion defects. The compression effect generated by Push-Assist is a type of inhomogeneous compression, which forms a coupled superposition effect of bending and inhomogeneous compression during the tube bending forming process, thus exerting a relatively complex influence on distortion. Therefore, this study theoretically analyzed the superposition mechanism of the compression effect of Push-Assist and the bending stress of the tube, and established a theoretical model of tube distortion under bending-compression conditions. By using the finite element simulation method and experimental verification method, the characteristics of tube distortion under different Push-Assist parameters were analyzed. The research conclusions show that: (1) The axial compression effect generated by Push-Assist at low speeds (v ≤ 0.9v0) has an inhibitory effect on bending distortion. The friction force of Push-Assist can generate a certain amount of compressive stress, which weakens the tensile stress on the outer wall during the bending process and thus effectively inhibits the cross-section distortion of the tube during bending. (2) An excessively high Push-Assist speed (0.9v0 < v ≤ 1.1v0) will aggravate tube distortion. This causes the tensile effect at the contact part between the lower side of the tube and the anti-wrinkling die to be gradually amplified, thereby further aggravating tube distortion. (3) The Push-Assist effect can enhance the tube’s forming limit. Under the condition where the Push-Assist speed is 0.9v0 and the friction coefficient μ at the contact surface between the pressure die and the tube is 0.4, the difference between the best and worst tube forming quality under the Push-Assist condition is 20.6%, with a 10.68% reduction in the maximum distortion rate of tube forming compared to the non-Push-Assist condition.

  • Open Access

    A Novel Pressure Drop Model for Seabed Airlift Devices Considering the Particle Sinking Effect

    by H. Long, Z. N. Wang, X. W. Wang, C. T. Tran

    Existing pressure drop model (PDM) ignores the particle sinking phenomenon in airlift devices and predict a much lower value than the actual one, which causes poor performance in the design and operation of airlift device. To solve this problem, a new PDM was proposed by considering this sinking phenomenon. Firstly, the particle sinking velocity in the airlift device was analyzed. Then, the phase volumetric fraction and phase velocity were calculated by considering this sinking effect. At last, a new pressure drop was derived from the calculated volumetric fractions and velocities. A distribution calculation method was proposed for calculating this new method and an experiment was conducted to verify the correctness of this new model. It was found that this new model has a high prediction accuracy with an error margin of 11%, which improves 12% compared with traditional models. This investigation proposed an accurate PDM and illustrated the effects of the particle sinking phenomenon on the hydrodynamics of gas liquid particle flow, which not only fills the gap in the PDM for ore airlift device, but also is beneficial to improve pump performance for high-efficiency transportation in ocean engineering.

  • Analysis of Residual Stresses in Bending and Forming of Aerospace Titanium Alloy Tubes Influenced by Temperature Variations

    by Huitao Li, Zhineng Wang, Guangfu Bin, Jing Tian, Renzhen Chen, tran trieu

    Titanium alloy bent tubes are extensively utilized in the aerospace industry, with thermal bending being a commonly employed fabrication method in recent years. This study investigates the residual stress in thin-walled titanium alloy tubes after bending. Through theoretical modeling, numerical simulations, and experimental analysis, the residual stress distribution and magnitude post bending in aerospace-grade titanium alloy tubes are examined. Initially, an analytical model for residual stress in titanium alloy tubes post bending unloading is established, followed by the creation of a three-dimensional thermal bending model using the finite element method. Subsequently, by theoretically calculating and simulating the temperature and stress field variations during the warm bending process of titanium alloy, the residual stress distribution and numerical solutions post bending are determined. Finally, experimental validation of the numerical simulation results is conducted using a stress tester, yielding good agreement between experimental and numerical simulation outcomes. The aim of this research is to provide a comprehensive theoretical understanding and solution for the residual stress issue in the thermal bending of titanium alloy aerospace tubes, thereby promoting scientific development and technological advancement in related fields.


  • Open Access

    An analytic model for TC4 titanium alloy tube bending springback considering temperature effects

    by Huitao Li, Zhineng Wang, Guangfu Bin, Jing Tian, Renzhen Chen, Weiming Ling, Yaocheng Ling

    Existing theoretical models for tube bending springback can hardly accurately predict the springback under warm bending conditions. Thus, a springback model was proposed by considering temperature effects. Specifically, the influence of temperature on the material performance was analyzed. Secondly, the area formulas of the tensile plastic zone and elastic zone of the outside section as well as that of the compressive plastic zone of the inside section during the formation of tube bending under temperature effects were derived. Furthermore, the stress distribution characteristics of the above zones were calculated. Then, a theoretical springback model of tube warm bending springback angle was established according to the mechanical equilibrium equation in the springback process. This new model was verified by finite element simulations and warm bending forming experiments of TC4 titanium alloy tubes. Results show that the prediction accuracy of this new model has reached 93%. Moreover, a higher temperature results in a smaller springback angle because it reduces tubes’ elastic layer area and axial stress. Above all, this research clarifies the problem of the unclear springback mechanism under the effect of long-term temperature rise, which provides a reference for subsequent research.

  • Open Access

    The Influence of Innovative Resources on the Comprehensive Carrying Capacity of China’s Urban Agglomerations: A System Dynamics Perspective

    by Lifang Yan, Wenzhong Ye, Hui Long, Qiong Zhang

    The sustainable development of urban agglomerations greatly relies on their comprehensive carrying capacity (CCC). As society evolves, innovative resources emerge as core assets and serve as crucial pillars of this capacity. Despite existing CCC studies, the influence of innovative resources remains underexplored. This study analyzes the influence of innovative resources on the CCC of 19 urban agglomerations in China using a system dynamics approach. We find that innovative resources are an important subsystem of CCC. Increasing innovative resources is an effective strategy for enhancing CCC, yet the effects of different types of innovative resources vary. Merely increasing the number of universities and research institutions does not significantly improve the CCC level. Increasing the expenditures of higher education institutions, internal R&D, and the number of patents are effective approaches to enhance CCC. Moreover, these factors can form a virtuous cycle, mutually promoting innovation and CCC development, thus injecting new momentum into the sustainable development of urban agglomerations.