Sarah E. Sofia
Sarah E. Sofia has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Ian Marius Peters
Helmholtz-Institut Erlangen-Nürnberg for Renewable Energies, Forschungszentrum Jülich, Erlangen, Germany
3 shared publications - Tonio Buonassisi
Massachusetts Institute of Technology, Cambridge, USA
2 shared publications - Anna Osherov
Massachusetts Institute of Technology Cambridge, MA 02139 USA, and also with Singapore-MIT Alliance for Research and Technology, Singapore 138602
1 shared publication - Annalisa Bruno
School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798, Singapore
1 shared publication - Axel F. Palmstrom
National Renewable Energy Laboratory, Golden, USA
1 shared publication - Billy J. Stanbery
Clean Energy Institute, Department of Chemical Engineering, University of Washington, University of Washington, Seattle, USA
1 shared publication
Latest Publications
- Open Access
- 5 December 2025
- Published by Elsevier in Cell Reports Sustainability
- Vol. 3 (2)
Carbon impact of intra-regional transmission congestion
- 5 December 2025
- Published by Elsevier in Cell Reports Sustainability
- Vol. 3 (2)
Open AccessCarbon impact of intra-regional transmission congestion
- Open Access
- 1 September 2024
- Published by IOP Publishing in Environmental Research: Energy
- Vol. 1 (3) , 035008
Validating locational marginal emissions models with wind generation
Increasingly large amounts of electric supply and load are being deliberately operated or sited on the basis of marginal emissions factor (MEF) models. Validating and calibrating such models is therefore of growing policy importance. This paper uses a natural experiment involving variation in relative changes in wind generation potential at wind farms in the ERCOT power grid to create a benchmark MEF and examine the relative accuracy of several common classes of short term MEF models. This work focuses on MEFs at the level of a few individual generating nodes, a much smaller geographic scale than the Balancing Authority (BA) or load zone. Additionally, the use of wind generation potential as a regressor allows us to factor in wind curtailment, in contrast to previous work. We evaluate multiple prevalent existing MEF models and find that both dispatch and statistical MEF models have a high degree of agreement with the benchmark MEF, while heat rate and average emissions do not. We also find that the emissions reduction benefits of optimizing electricity with MEFs using a geographically granular model instead of a BA-wide model are 1.4, 1.3 and 1.5 times larger for dispatch, statistical and heat rate models, respectively.
- 1 September 2024
- Published by IOP Publishing in Environmental Research: Energy
- Vol. 1 (3) , 035008
Open AccessValidating locational marginal emissions models with wind generation
Increasingly large amounts of electric supply and load are being deliberately operated or sited on the basis of marginal emissions factor (MEF) models. Validating and calibrating such models is therefore of growing policy importance. This paper uses a natural experiment involving variation in relative changes in wind generation potential at wind farms in the ERCOT power grid to create a benchmark MEF and examine the relative accuracy of several common classes of short term MEF models. This work focuses on MEFs at the level of a few individual generating nodes, a much smaller geographic scale than the Balancing Authority (BA) or load zone. Additionally, the use of wind generation potential as a regressor allows us to factor in wind curtailment, in contrast to previous work. We evaluate multiple prevalent existing MEF models and find that both dispatch and statistical MEF models have a high degree of agreement with the benchmark MEF, while heat rate and average emissions do not. We also find that the emissions reduction benefits of optimizing electricity with MEFs using a geographically granular model instead of a BA-wide model are 1.4, 1.3 and 1.5 times larger for dispatch, statistical and heat rate models, respectively.
- Open Access
- 11 December 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 4 (2) , 852-862
Roadmap for cost-effective, commercially-viable perovskite silicon tandems for the current and future PV market
A techno-economic analysis of perovskite-silicon tandem solar modules is presented, outlining the most viable pathway for designing cost-effective, commercially viable tandems.
- 11 December 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 4 (2) , 852-862
Open AccessRoadmap for cost-effective, commercially-viable perovskite silicon tandems for the current and future PV market
A techno-economic analysis of perovskite-silicon tandem solar modules is presented, outlining the most viable pathway for designing cost-effective, commercially viable tandems.
- 30 April 2018
- Published by Springer Nature in Nature Energy
- Vol. 3 (5) , 387-394
Economic viability of thin-film tandem solar modules in the United States
- 30 April 2018
- Published by Springer Nature in Nature Energy
- Vol. 3 (5) , 387-394
Economic viability of thin-film tandem solar modules in the United States
- Open Access
- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 1023-1028
Developing a Robust Recombination Contact to Realize Monolithic Perovskite Tandems With Industrially Common p-Type Silicon Solar Cells
Although two-terminal perovskite-silicon tandem solar cells have rapidly increased in efficiency, they have only been demonstrated with n-type silicon, which currently constitutes less than 5% of the global photovoltaics market. In this paper, we realize the first two-terminal perovskite tandem with p-type silicon by developing a recombination contact that enables voltage addition without damaging either subcell. We find that silicon interband recombination contacts are limited by a $\text{SiO}_{x}$ charge-extraction barrier, which forms during oxidative top-cell fabrication. A sputtered 30-nm indium tin oxide layer is found to protect the silicon cell surface from oxidation, while forming a recombination contact with the p-type nickel oxide hole transport layer for the perovskite top cell. Using this recombination contact we achieve voltage addition between the perovskite top cell and aluminum back-surface field p-type silicon bottom cell. We also find that minimizing moisture on the nickel oxide surface is important for achieving a stable open-circuit voltage under illumination. The recombination contact developed herein could play an important role in near-future developments.- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 1023-1028
Open AccessDeveloping a Robust Recombination Contact to Realize Monolithic Perovskite Tandems With Industrially Common p-Type Silicon Solar Cells
Although two-terminal perovskite-silicon tandem solar cells have rapidly increased in efficiency, they have only been demonstrated with n-type silicon, which currently constitutes less than 5% of the global photovoltaics market. In this paper, we realize the first two-terminal perovskite tandem with p-type silicon by developing a recombination contact that enables voltage addition without damaging either subcell. We find that silicon interband recombination contacts are limited by a $\text{SiO}_{x}$ charge-extraction barrier, which forms during oxidative top-cell fabrication. A sputtered 30-nm indium tin oxide layer is found to protect the silicon cell surface from oxidation, while forming a recombination contact with the p-type nickel oxide hole transport layer for the perovskite top cell. Using this recombination contact we achieve voltage addition between the perovskite top cell and aluminum back-surface field p-type silicon bottom cell. We also find that minimizing moisture on the nickel oxide surface is important for achieving a stable open-circuit voltage under illumination. The recombination contact developed herein could play an important role in near-future developments.