Marcelo Arau´jo Vitola
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marcelo Arau´jo Vitola has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Paulo de Tarso Themistocles Esperança
Federal University of Rio de Janeiro, Rio de Janeiro, Brazil
16 shared publications Sergio H. Sphaier
16 shared publications- Jassiel Vladimir Hernández Fontes
Grupo de Pesquisa Tecnologias Navais e Sustentáveis (TNS), Curso de Engenharia Naval, Escola Superior de Tecnologia, Universidade do Estado do Amazonas, Manaus 69050-020, Brazil
6 shared publications Carlos Levi
Federal University of Rio de Janeiro
4 shared publicationsJuan B. V. Wanderley
University of Rio de Janeiro, Rio de Janeiro, RJ, Brazil
4 shared publications- Mojtaba Maali Amiri
Ocean Engineering Department - Offshore Renewable Energy Group - GERO/COPPE, Federal University of Rio de Janeiro, Rio de Janeiro, Brazil
4 shared publications
Latest Publications
- 1 July 2019
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 76, 98-114
Investigation into the wave system of a generic submarine moving along a straight path beneath the free surface
- 1 July 2019
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 76, 98-114
Investigation into the wave system of a generic submarine moving along a straight path beneath the free surface
- 1 March 2019
- Published by Elsevier in Applied Ocean Research
- Vol. 84, 192-205
URANS investigation of the interaction between the free surface and a shallowly submerged underwater vehicle at steady drift
- 1 March 2019
- Published by Elsevier in Applied Ocean Research
- Vol. 84, 192-205
URANS investigation of the interaction between the free surface and a shallowly submerged underwater vehicle at steady drift
- 8 January 2019
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 31 (3) , 570-581
RANS feasibility study of using roughness to mimic transition strip effect on the crossflowseparation over a 6:1 prolate-spheroid
- 8 January 2019
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 31 (3) , 570-581
RANS feasibility study of using roughness to mimic transition strip effect on the crossflowseparation over a 6:1 prolate-spheroid
- 1 January 2019
- Published by Elsevier in Applied Ocean Research
- Vol. 82, 63-73
Assessing shipping water vertical loads on a fixed structure by convolution model and wet dam-break tests
- 1 January 2019
- Published by Elsevier in Applied Ocean Research
- Vol. 82, 63-73
Assessing shipping water vertical loads on a fixed structure by convolution model and wet dam-break tests
- 4 December 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 82, 415-429
Analytical convolution model for shipping water evolution on a fixed structure
- 4 December 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 82, 415-429
Analytical convolution model for shipping water evolution on a fixed structure
- 1 July 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 76, 34-50
How does the free surface affect the hydrodynamics of a shallowly submerged submarine?
- 1 July 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 76, 34-50
How does the free surface affect the hydrodynamics of a shallowly submerged submarine?
- 17 June 2018
- Published by ASME International
Wave Force on a Partially Submerged Fixed Horizontal Circular Cylinder
Circular cylinders are one of the most common geometries used in many structures, such as fixed platforms, risers, umbilical cables, offshore fish farms, floating offshore wind turbines, wave energy devices, plastic cleanup booms, and oil containment booms. Although partially submerged horizontal circular cylinders can be found in many offshore and marine structures, few works have investigated the influence of their positions beneath the free surface and the resulting wave force. The present work aimed to numerically study the wave force acting on a fixed horizontal circular cylinder near the free surface for different depths. The wave flow was modeled using a viscous model available in the StarCCM+ software using a two-dimensional numerical wave tank. The governing equations were solved using the finite volume in an unstructured mesh. A circular cylinder with a diameter (D) of 0.10 m and a regular wave with a steepness (H/L) of 0.025 were used in the present study. In this case, the cylinder diameter is much smaller than the wave length. Three different submerged depths were investigated, and the numerical results were compared with experimental data extracted from Dixon [1]. Good agreement was found for the first two cylinder positions (zc/D = 0 and −0.3). For the last case (zc/D = −0.5), a phase shift was observed. However, by correcting it, the agreement between the numerical and experimental data was also good.
- 17 June 2018
- Published by ASME International
Wave Force on a Partially Submerged Fixed Horizontal Circular Cylinder
Circular cylinders are one of the most common geometries used in many structures, such as fixed platforms, risers, umbilical cables, offshore fish farms, floating offshore wind turbines, wave energy devices, plastic cleanup booms, and oil containment booms. Although partially submerged horizontal circular cylinders can be found in many offshore and marine structures, few works have investigated the influence of their positions beneath the free surface and the resulting wave force. The present work aimed to numerically study the wave force acting on a fixed horizontal circular cylinder near the free surface for different depths. The wave flow was modeled using a viscous model available in the StarCCM+ software using a two-dimensional numerical wave tank. The governing equations were solved using the finite volume in an unstructured mesh. A circular cylinder with a diameter (D) of 0.10 m and a regular wave with a steepness (H/L) of 0.025 were used in the present study. In this case, the cylinder diameter is much smaller than the wave length. Three different submerged depths were investigated, and the numerical results were compared with experimental data extracted from Dixon [1]. Good agreement was found for the first two cylinder positions (zc/D = 0 and −0.3). For the last case (zc/D = −0.5), a phase shift was observed. However, by correcting it, the agreement between the numerical and experimental data was also good.
- 1 June 2018
- Published by Elsevier in Ocean Engineering
- Vol. 157, 325-338
Water elevation measurements using binary image analysis for 2D hydrodynamic experiments
- 1 June 2018
- Published by Elsevier in Ocean Engineering
- Vol. 157, 325-338
Water elevation measurements using binary image analysis for 2D hydrodynamic experiments
- 21 May 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (5) , 051101
On the Generation of Isolated Green Water Events Using Wet Dam-Break
Green water occurs when an incoming wave exceeds the freeboard and propagates onto the deck of naval/offshore structures, such as floating production storage and offloading units and platforms. This water can affect the integrity of facilities and equipment that are installed on the deck, compromise the safety of the crew, and affect the dynamic stability of the structure. Traditionally, wave trains have been used to study the green water problem, which is a good approach to analyzing consecutive green water events. However, to carry out systematic studies that allow local details to be identified for different types of green water, an alternative method is to study isolated events generated by a single incoming wave. The purpose of this paper was to experimentally investigate the generation of different types of isolated green water events using the wet dam-break (DB) approach as an alternative to generating the incoming wave. Tests were carried out in a rectangular tank with a fixed internal structure. Different freeboard conditions were tested for two aspect ratios of the wet DB ( and 0.6). Conventional wave probes were used to measure the water levels in the tank, and a high-speed camera was set to capture details of the generated green water events. The results demonstrated the ability of this approach to represent different types of green water, similar to those obtained with unbroken regular waves in barge-shaped fixed structures, including DB, plunging-dam-break (PDB) and hammer-fist (HF).- 21 May 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (5) , 051101
On the Generation of Isolated Green Water Events Using Wet Dam-Break
Green water occurs when an incoming wave exceeds the freeboard and propagates onto the deck of naval/offshore structures, such as floating production storage and offloading units and platforms. This water can affect the integrity of facilities and equipment that are installed on the deck, compromise the safety of the crew, and affect the dynamic stability of the structure. Traditionally, wave trains have been used to study the green water problem, which is a good approach to analyzing consecutive green water events. However, to carry out systematic studies that allow local details to be identified for different types of green water, an alternative method is to study isolated events generated by a single incoming wave. The purpose of this paper was to experimentally investigate the generation of different types of isolated green water events using the wet dam-break (DB) approach as an alternative to generating the incoming wave. Tests were carried out in a rectangular tank with a fixed internal structure. Different freeboard conditions were tested for two aspect ratios of the wet DB ( and 0.6). Conventional wave probes were used to measure the water levels in the tank, and a high-speed camera was set to capture details of the generated green water events. The results demonstrated the ability of this approach to represent different types of green water, similar to those obtained with unbroken regular waves in barge-shaped fixed structures, including DB, plunging-dam-break (PDB) and hammer-fist (HF).- 22 February 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (4)
Numerical Uncertainty Analysis in Regular Wave Modeling
In recent decades, the use of computational fluid dynamics (CFD) in many areas of engineering as a research and development tool has seen remarkable growth. Recently, an increasing concern with the assessment of the quality of CFD results has been observed. Wave modeling is an important task in many ocean engineering applications. Although numerical modeling studies of waves can be found in the literature for many applications, it is hard to find studies that present the numerical uncertainties of the results. In this study, the numerical uncertainties in mean wave parameters simulated using a viscous model were estimated using a procedure based on grid/time refinement studies and power series expansions. starccm+ software was used to simulate wave propagation. The computational domain was discretized using a trimmer mesh. The results obtained for a regular wave with a wave steepness (H/L) equal to 0.025 are presented. The numerical uncertainties in mean wave height and mean wave period were estimated along the computational domain. The results indicate that the convergence properties of the mean wave parameters with the grid refinement depended on both position in the domain and the selected wave parameter.
- 22 February 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (4)
Numerical Uncertainty Analysis in Regular Wave Modeling
In recent decades, the use of computational fluid dynamics (CFD) in many areas of engineering as a research and development tool has seen remarkable growth. Recently, an increasing concern with the assessment of the quality of CFD results has been observed. Wave modeling is an important task in many ocean engineering applications. Although numerical modeling studies of waves can be found in the literature for many applications, it is hard to find studies that present the numerical uncertainties of the results. In this study, the numerical uncertainties in mean wave parameters simulated using a viscous model were estimated using a procedure based on grid/time refinement studies and power series expansions. starccm+ software was used to simulate wave propagation. The computational domain was discretized using a trimmer mesh. The results obtained for a regular wave with a wave steepness (H/L) equal to 0.025 are presented. The numerical uncertainties in mean wave height and mean wave period were estimated along the computational domain. The results indicate that the convergence properties of the mean wave parameters with the grid refinement depended on both position in the domain and the selected wave parameter.