Yunli Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yunli Feng has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
Minghe Zhang
7 shared publicationsFucheng Zhang
5 shared publicationsGuolong Liu
Key Laboratory of the Ministry of Education for Modern Metallurgy Technology, Tangshan, P.R. China
5 shared publications- Liguang Wang
College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063009, China
3 shared publications - Minghe Zhang
College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063210, China
3 shared publications Dongmei Zhang
College of Metallurgy and Energy, North China University of Science and Technology, Tangshan, P.R. China
2 shared publications
Latest Publications
- Open Access
- 24 September 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 2262-2292
Strategies for achieving high strength and ductility in non-equiatomic high-entropy alloys: structural control and mechanistic insights
- 24 September 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 2262-2292
Open AccessStrategies for achieving high strength and ductility in non-equiatomic high-entropy alloys: structural control and mechanistic insights
- Open Access
Flow Stress Model of Hot Deformation for CoNiV Medium Entropy Alloy
Hot compression experiments were performed to characterize the high-temperature deformation behavior of CoNiV medium-entropy alloy (MEA). Hot compression tests were carried out using a Gleeble-3500 thermomechanical simulator over strain rates of 0.001 s−1 to 1 s−1 and temperatures ranging between 950 °C and 1100 °C. Based on the experimentally determined hot compression data, three models for predicting the flow stress of CoNiV MEA were established: the Zerilli-Armstrong (Z-A) constitutive model, an artificial neural network (ANN) model, and a gated recurrent unit (GRU) model. This study comprehensively evaluated the prediction accuracy of each model using the coefficient of determination (R2), mean absolute error (MAE), and root mean square error (RMSE). The results show that, compared with the other two models, the Z-A model cannot accurately predict the flow behavior of CoNiV MEA in the studied hot-working regime. The R2 value of the ANN model is 0.98974, while the GRU model exhibits the highest predictive capability, with an R2 value of 0.98981, an MAE of 6.29621, and an RMSE of 13.10832. The proposed model demonstrates superior prediction accuracy compared with other models, enabling high-precision characterization of the high-temperature evolution of the flow stress in the CoNiV MEA. This study provides a theoretical foundation for the design and optimization of hot working parameters for the CoNiV MEA.
Open AccessFlow Stress Model of Hot Deformation for CoNiV Medium Entropy Alloy
Hot compression experiments were performed to characterize the high-temperature deformation behavior of CoNiV medium-entropy alloy (MEA). Hot compression tests were carried out using a Gleeble-3500 thermomechanical simulator over strain rates of 0.001 s−1 to 1 s−1 and temperatures ranging between 950 °C and 1100 °C. Based on the experimentally determined hot compression data, three models for predicting the flow stress of CoNiV MEA were established: the Zerilli-Armstrong (Z-A) constitutive model, an artificial neural network (ANN) model, and a gated recurrent unit (GRU) model. This study comprehensively evaluated the prediction accuracy of each model using the coefficient of determination (R2), mean absolute error (MAE), and root mean square error (RMSE). The results show that, compared with the other two models, the Z-A model cannot accurately predict the flow behavior of CoNiV MEA in the studied hot-working regime. The R2 value of the ANN model is 0.98974, while the GRU model exhibits the highest predictive capability, with an R2 value of 0.98981, an MAE of 6.29621, and an RMSE of 13.10832. The proposed model demonstrates superior prediction accuracy compared with other models, enabling high-precision characterization of the high-temperature evolution of the flow stress in the CoNiV MEA. This study provides a theoretical foundation for the design and optimization of hot working parameters for the CoNiV MEA.
- Open Access
Effect of Torsion on Microstructure and Mechanical Properties of Medium Manganese Steel
In this study, a multi-gradient microstructure was introduced into medium-Mn steel through torsion following heat treatment at different annealing temperatures, and through investigations on the mechanical properties under two annealing temperatures, it has also been revealed that different annealing temperatures before torsion affect the stability of austenite after torsion, thereby leading to distinct variations in mechanical performance. The yield strengths of the studied steel after annealing at 600 °C and 620 °C were 762 MPa and 673 MPa, with total elongation of 47.4% and 44.1%, respectively. After 90° torsion, the yield strength of experimental steels increased to 834 MPa and 808 MPa, while the elongation decreased to 21.6% and 29.5%, respectively. The gradient distributions from the center to the edge were observed for the austenite volume fraction, average grain size, martensite volume fraction, GND density, and hardness. The comparative analysis of the two annealing temperatures indicates that the larger grain size in the 620—annealed sample leads to its lower yield strength, while its higher austenite volume fraction and moderate stability promote a more sustained TRIP effect during deformation, contributing to its enhanced elongation. This multi-gradient microstructure is responsible for the yield strength improvements of 72 MPa and 135 MPa in the torsioned samples annealed at 600 °C and 620 °C, respectively.
Open AccessEffect of Torsion on Microstructure and Mechanical Properties of Medium Manganese Steel
In this study, a multi-gradient microstructure was introduced into medium-Mn steel through torsion following heat treatment at different annealing temperatures, and through investigations on the mechanical properties under two annealing temperatures, it has also been revealed that different annealing temperatures before torsion affect the stability of austenite after torsion, thereby leading to distinct variations in mechanical performance. The yield strengths of the studied steel after annealing at 600 °C and 620 °C were 762 MPa and 673 MPa, with total elongation of 47.4% and 44.1%, respectively. After 90° torsion, the yield strength of experimental steels increased to 834 MPa and 808 MPa, while the elongation decreased to 21.6% and 29.5%, respectively. The gradient distributions from the center to the edge were observed for the austenite volume fraction, average grain size, martensite volume fraction, GND density, and hardness. The comparative analysis of the two annealing temperatures indicates that the larger grain size in the 620—annealed sample leads to its lower yield strength, while its higher austenite volume fraction and moderate stability promote a more sustained TRIP effect during deformation, contributing to its enhanced elongation. This multi-gradient microstructure is responsible for the yield strength improvements of 72 MPa and 135 MPa in the torsioned samples annealed at 600 °C and 620 °C, respectively.
- Open Access
- 15 April 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (6) , 1067-1077
Dependence of Mechanical Properties and Deformation Behavior of TRIP-FeMnCoCrAl Dual-phase High-entropy Alloy on Grain Size and Strain Rate
Fe50Mn30Co10Cr10 dual-phase metastable high-entropy alloys(HEAS) have gained significant attention for their outstanding mechanical properties. However, limited research has explored the relationship between grain size and strain rate sensitivity (SRS) in dual-phase HEAS. Current investigations primarily focus on pure metals and single-phase FCC HEAS. To address this gap, this study examines the impact of grain size on the deformation behavior and SRS of TRIP-(Fe50Mn30Co10Cr10)97Al3 dual-phase HEAS. Two variants of dual-phase HEAS were prepared, distinguished by their grain sizes (2.86 μm, labeled Fine Grain or FG, and 5.25 μm, termed Coarse Grain or CG), via the vacuum melting method. Subsequent tensile tests were conducted at varying strain rates, ranging from 0.001/s to 0.02/s. The findings unveil a robust grain size dependency in the phase transformation and deformation twinning of the (Fe50Mn30Co10Cr10)97Al3 dual-phase HEA during tensile deformation. Within the FeMnCoCrAl HEA system, characterized by a dual-phase structure, both TRIP (Transformation-Induced Plasticity) and TWIP (Twinning-Induced Plasticity) effects intensify with increasing grain size. Additionally, as the strain rate increases, the TRIP effect gradually diminishes while the TWIP effect strengthens. Notably, the strain rate sensitivity index 'm' exhibits a downward trend with an increase in grain size, distinguishing it from the behavior observed in single-phase FCC HEAS. This study conducts an in-depth analysis of grain size's impact on the SRS of (Fe50Mn30Co10Cr10)97Al3 dual-phase HEA, scrutinizing micro-level aspects encompassing phase transformation, deformation twinning, and grain boundary slip. The findings provide essential theoretical insights for designing HEAS tailored for applications requiring high strain rates.
- 15 April 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (6) , 1067-1077
Open AccessDependence of Mechanical Properties and Deformation Behavior of TRIP-FeMnCoCrAl Dual-phase High-entropy Alloy on Grain Size and Strain Rate
Fe50Mn30Co10Cr10 dual-phase metastable high-entropy alloys(HEAS) have gained significant attention for their outstanding mechanical properties. However, limited research has explored the relationship between grain size and strain rate sensitivity (SRS) in dual-phase HEAS. Current investigations primarily focus on pure metals and single-phase FCC HEAS. To address this gap, this study examines the impact of grain size on the deformation behavior and SRS of TRIP-(Fe50Mn30Co10Cr10)97Al3 dual-phase HEAS. Two variants of dual-phase HEAS were prepared, distinguished by their grain sizes (2.86 μm, labeled Fine Grain or FG, and 5.25 μm, termed Coarse Grain or CG), via the vacuum melting method. Subsequent tensile tests were conducted at varying strain rates, ranging from 0.001/s to 0.02/s. The findings unveil a robust grain size dependency in the phase transformation and deformation twinning of the (Fe50Mn30Co10Cr10)97Al3 dual-phase HEA during tensile deformation. Within the FeMnCoCrAl HEA system, characterized by a dual-phase structure, both TRIP (Transformation-Induced Plasticity) and TWIP (Twinning-Induced Plasticity) effects intensify with increasing grain size. Additionally, as the strain rate increases, the TRIP effect gradually diminishes while the TWIP effect strengthens. Notably, the strain rate sensitivity index 'm' exhibits a downward trend with an increase in grain size, distinguishing it from the behavior observed in single-phase FCC HEAS. This study conducts an in-depth analysis of grain size's impact on the SRS of (Fe50Mn30Co10Cr10)97Al3 dual-phase HEA, scrutinizing micro-level aspects encompassing phase transformation, deformation twinning, and grain boundary slip. The findings provide essential theoretical insights for designing HEAS tailored for applications requiring high strain rates.
- 11 September 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (6) , 1-13
Multiscale Microstructure Evolution and Subgrain Strengthening of Warm-Rolled Ultrafine Pearlite Steel
- 11 September 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (6) , 1-13
Multiscale Microstructure Evolution and Subgrain Strengthening of Warm-Rolled Ultrafine Pearlite Steel
- 15 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (4) , 1364-1378
Regulation on Annealing Multiscale Laminar Structure and Mechanical Characteristics of Plain Medium Carbon Steel by Warm Pre-deformation Extent
- 15 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (4) , 1364-1378
Regulation on Annealing Multiscale Laminar Structure and Mechanical Characteristics of Plain Medium Carbon Steel by Warm Pre-deformation Extent
- 11 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868
Strength and ductility enhancement of plain carbon steel by heterostructure design
- 11 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868
Strength and ductility enhancement of plain carbon steel by heterostructure design