Philip Krantz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Philip Krantz has a total of 148 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Bengtsson
Google Research, Mountain View, CA, USA
6 shared publications - Jonas Bylander
Chalmers University of Technology
6 shared publications - Per Delsing
Chalmers University of Technology
6 shared publications Simon Gustavsson
Research Laboratory of Electronics, Massachusetts Institute of Technology, Cambridge, MA, USA
6 shared publications- Michaël Simoen
Department of Microtechnology and Nanoscience (MC2), Chalmers University of Technology, Gothenburg SE-412 96, Sweden
5 shared publications - Morten Kjaergaard
Center for Quantum Devices, Niels Bohr Institute, University of Copenhagen, Copenhagen, Denmark
5 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (8) , 1700910
Designing Josephson Traveling-Wave Parametric Amplifiers: EM-Circuit Cosimulation and Experimental Validation
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (8) , 1700910
Designing Josephson Traveling-Wave Parametric Amplifiers: EM-Circuit Cosimulation and Experimental Validation
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
- 15 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (2) , 1-11
Modeling Flux-Quantizing Josephson Junction Circuits in Keysight ADS
We introduce Josephson junction and inductor models in Keysight Advanced Design System that feature an auxiliary flux port, and facilitate the expression of flux quantization conditions in simulation of superconducting microwave circuits. We present several examples that illustrate our methodology for constructing flux-quantizing circuits, including dc- andrf-SQUIDs, tunable couplers, and parametric amplifiers using superconducting nonlinear asymmetric inductive element and rf-SQUID arrays. We perform dc, S-parameter, and harmonic balance simulations to validate our models and methods against theory and published experimental results.
- 15 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (2) , 1-11
Modeling Flux-Quantizing Josephson Junction Circuits in Keysight ADS
We introduce Josephson junction and inductor models in Keysight Advanced Design System that feature an auxiliary flux port, and facilitate the expression of flux quantization conditions in simulation of superconducting microwave circuits. We present several examples that illustrate our methodology for constructing flux-quantizing circuits, including dc- andrf-SQUIDs, tunable couplers, and parametric amplifiers using superconducting nonlinear asymmetric inductive element and rf-SQUID arrays. We perform dc, S-parameter, and harmonic balance simulations to validate our models and methods against theory and published experimental results.
- Open Access
- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 054004
Microwave calibration of qubit drive line components at millikelvin temperatures
Systematic errors in qubit state preparation arise due to non-idealities in qubit control lines such as impedance mismatch. Using a data-based methodology of short-open-load calibration at a temperature of 30 mK, we report calibrated 1-port scattering parameter data of individual qubit drive line components. At 5 GHz, cryogenic return losses of a 20-dB-attenuator, a 10-dB-attenuator, a 230-mm-long 0.86-mm silver-plated cupronickel coaxial cable, and a 230-mm-long 0.86-mm NbTi coaxial cable were found to be dB, dB, dB, and dB, respectively. For the same frequency, we also extract cryogenic insertion losses of dB and dB for the coaxial cables. We interpret the results using master equation simulation of all XY gates performed on a single qubit. For example, we simulate a sequence of two 5 ns gate pulses (X and Y) through a two-element Fabry–Pérot cavity with 276-mm path length directly preceding the qubit and establish that the return loss of its reflective elements must be >9.7 dB (>14.7 dB) to obtain 99.9% (99.99%) gate fidelity.- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 054004
Open AccessMicrowave calibration of qubit drive line components at millikelvin temperatures
Systematic errors in qubit state preparation arise due to non-idealities in qubit control lines such as impedance mismatch. Using a data-based methodology of short-open-load calibration at a temperature of 30 mK, we report calibrated 1-port scattering parameter data of individual qubit drive line components. At 5 GHz, cryogenic return losses of a 20-dB-attenuator, a 10-dB-attenuator, a 230-mm-long 0.86-mm silver-plated cupronickel coaxial cable, and a 230-mm-long 0.86-mm NbTi coaxial cable were found to be dB, dB, dB, and dB, respectively. For the same frequency, we also extract cryogenic insertion losses of dB and dB for the coaxial cables. We interpret the results using master equation simulation of all XY gates performed on a single qubit. For example, we simulate a sequence of two 5 ns gate pulses (X and Y) through a two-element Fabry–Pérot cavity with 276-mm path length directly preceding the qubit and establish that the return loss of its reflective elements must be >9.7 dB (>14.7 dB) to obtain 99.9% (99.99%) gate fidelity. - Open Access
- 7 January 2022
- Published by American Physical Society (APS) in Physical Review X
- Vol. 12 (1) , 011005
Demonstration of Density Matrix Exponentiation Using a Superconducting Quantum Processor
Density matrix exponentiation (DME) is a general technique for using a quantum state to enact the quantum operation on a target system. It was first proposed in the context of quantum machine learning, but has since been shown to have broad applications in quantum metrology and computation. No experimental demonstration of DME has been performed thus far due to its demanding circuit depths and the need to efficiently generate multiple identical copies of during the finite lifetime of the target system. In this work, we describe the first demonstration of the DME algorithm, which we accomplish using a superconducting quantum processor. Our demonstration relies on a 99.7% fidelity controlled-phase gate implemented using two tunable superconducting transmon qubits. We achieve a fidelity surpassing 90% at circuit depths exceeding 70 when comparing the output of the circuit executed on our quantum processor to a simulation assuming perfect operations and measurements.- 7 January 2022
- Published by American Physical Society (APS) in Physical Review X
- Vol. 12 (1) , 011005
Open AccessDemonstration of Density Matrix Exponentiation Using a Superconducting Quantum Processor
Density matrix exponentiation (DME) is a general technique for using a quantum state to enact the quantum operation on a target system. It was first proposed in the context of quantum machine learning, but has since been shown to have broad applications in quantum metrology and computation. No experimental demonstration of DME has been performed thus far due to its demanding circuit depths and the need to efficiently generate multiple identical copies of during the finite lifetime of the target system. In this work, we describe the first demonstration of the DME algorithm, which we accomplish using a superconducting quantum processor. Our demonstration relies on a 99.7% fidelity controlled-phase gate implemented using two tunable superconducting transmon qubits. We achieve a fidelity surpassing 90% at circuit depths exceeding 70 when comparing the output of the circuit executed on our quantum processor to a simulation assuming perfect operations and measurements. - Open Access
- 11 February 2021
- Published by Springer Nature in Nature Communications
- Vol. 12 (1) , 1-9
Multi-level quantum noise spectroscopy
System noise identification is crucial to the engineering of robust quantum systems. Although existing quantum noise spectroscopy (QNS) protocols measure an aggregate amount of noise affecting a quantum system, they generally cannot distinguish between the underlying processes that contribute to it. Here, we propose and experimentally validate a spin-locking-based QNS protocol that exploits the multi-level energy structure of a superconducting qubit to achieve two notable advances. First, our protocol extends the spectral range of weakly anharmonic qubit spectrometers beyond the present limitations set by their lack of strong anharmonicity. Second, the additional information gained from probing the higher-excited levels enables us to identify and distinguish contributions from different underlying noise mechanisms.
- 11 February 2021
- Published by Springer Nature in Nature Communications
- Vol. 12 (1) , 1-9
Open AccessMulti-level quantum noise spectroscopy
System noise identification is crucial to the engineering of robust quantum systems. Although existing quantum noise spectroscopy (QNS) protocols measure an aggregate amount of noise affecting a quantum system, they generally cannot distinguish between the underlying processes that contribute to it. Here, we propose and experimentally validate a spin-locking-based QNS protocol that exploits the multi-level energy structure of a superconducting qubit to achieve two notable advances. First, our protocol extends the spectral range of weakly anharmonic qubit spectrometers beyond the present limitations set by their lack of strong anharmonicity. Second, the additional information gained from probing the higher-excited levels enables us to identify and distinguish contributions from different underlying noise mechanisms.
- Open Access
- 8 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (6) , 064002
Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above s ( ). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty -cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.- 8 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (6) , 064002
Open AccessSimplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above s ( ). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty -cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer. - Open Access
Programming a quantum computer with quantum instructions
The equivalence between the instructions used to define programs and the input data on which the instructions operate is a basic principle of classical computer architectures and programming. Replacing classical data with quantum states enables fundamentally new computational capabilities with scaling advantages for many applications, and numerous models have been proposed for realizing quantum computation. However, within each of these models, the quantum data are transformed by a set of gates that are compiled using solely classical information. Conventional quantum computing models thus break the instruction-data symmetry: classical instructions and quantum data are not directly interchangeable. In this work, we use a density matrix exponentiation protocol to execute quantum instructions on quantum data. In this approach, a fixed sequence of classically-defined gates performs an operation that uniquely depends on an auxiliary quantum instruction state. Our demonstration relies on a 99.7% fidelity controlled-phase gate implemented using two tunable superconducting transmon qubits, which enables an algorithmic fidelity surpassing 90% at circuit depths exceeding 70. The utilization of quantum instructions obviates the need for costly tomographic state reconstruction and recompilation, thereby enabling exponential speedup for a broad range of algorithms, including quantum principal component analysis, the measurement of entanglement spectra, and universal quantum emulation.
Open AccessProgramming a quantum computer with quantum instructions
The equivalence between the instructions used to define programs and the input data on which the instructions operate is a basic principle of classical computer architectures and programming. Replacing classical data with quantum states enables fundamentally new computational capabilities with scaling advantages for many applications, and numerous models have been proposed for realizing quantum computation. However, within each of these models, the quantum data are transformed by a set of gates that are compiled using solely classical information. Conventional quantum computing models thus break the instruction-data symmetry: classical instructions and quantum data are not directly interchangeable. In this work, we use a density matrix exponentiation protocol to execute quantum instructions on quantum data. In this approach, a fixed sequence of classically-defined gates performs an operation that uniquely depends on an auxiliary quantum instruction state. Our demonstration relies on a 99.7% fidelity controlled-phase gate implemented using two tunable superconducting transmon qubits, which enables an algorithmic fidelity surpassing 90% at circuit depths exceeding 70. The utilization of quantum instructions obviates the need for costly tomographic state reconstruction and recompilation, thereby enabling exponential speedup for a broad range of algorithms, including quantum principal component analysis, the measurement of entanglement spectra, and universal quantum emulation.
- Open Access
- 3 September 2020
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 14 (3) , 034010
Improved Success Probability with Greater Circuit Depth for the Quantum Approximate Optimization Algorithm
Present-day, noisy, small or intermediate-scale quantum processors—although far from fault tolerant—support the execution of heuristic quantum algorithms, which might enable a quantum advantage, for example, when applied to combinatorial optimization problems. On small-scale quantum processors, validations of such algorithms serve as important technology demonstrators. We implement the quantum approximate optimization algorithm on our hardware platform, consisting of two superconducting transmon qubits and one parametrically modulated coupler. We solve small instances of the NP (nondeterministic polynomial time)-complete exact-cover problem, with 96.6% success probability, by iterating the algorithm up to level two.
- 3 September 2020
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 14 (3) , 034010
Open AccessImproved Success Probability with Greater Circuit Depth for the Quantum Approximate Optimization Algorithm
Present-day, noisy, small or intermediate-scale quantum processors—although far from fault tolerant—support the execution of heuristic quantum algorithms, which might enable a quantum advantage, for example, when applied to combinatorial optimization problems. On small-scale quantum processors, validations of such algorithms serve as important technology demonstrators. We implement the quantum approximate optimization algorithm on our hardware platform, consisting of two superconducting transmon qubits and one parametrically modulated coupler. We solve small instances of the NP (nondeterministic polynomial time)-complete exact-cover problem, with 96.6% success probability, by iterating the algorithm up to level two.
- Top Cited Papers
- 29 July 2020
- Published by Springer Nature in Nature
- Vol. 583 (7818) , 775-779
Waveguide quantum electrodynamics with superconducting artificial giant atoms
Models of light–matter interactions in quantum electrodynamics typically invoke the dipole approximation1,2, in which atoms are treated as point-like objects when compared to the wavelength of the electromagnetic modes with which they interact. However, when the ratio between the size of the atom and the mode wavelength is increased, the dipole approximation no longer holds and the atom is referred to as a ‘giant atom’2,3. So far, experimental studies with solid-state devices in the giant-atom regime have been limited to superconducting qubits that couple to short-wavelength surface acoustic waves4,5,6,7,8,9,10, probing the properties of the atom at only a single frequency. Here we use an alternative architecture that realizes a giant atom by coupling small atoms to a waveguide at multiple, but well separated, discrete locations. This system enables tunable atom–waveguide couplings with large on–off ratios3 and a coupling spectrum that can be engineered by the design of the device. We also demonstrate decoherence-free interactions between multiple giant atoms that are mediated by the quasi-continuous spectrum of modes in the waveguide—an effect that is not achievable using small atoms11. These features allow qubits in this architecture to switch between protected and emissive configurations in situ while retaining qubit–qubit interactions, opening up possibilities for high-fidelity quantum simulations and non-classical itinerant photon generation12,13.
- 29 July 2020
- Published by Springer Nature in Nature
- Vol. 583 (7818) , 775-779
Top Cited PapersWaveguide quantum electrodynamics with superconducting artificial giant atoms
Models of light–matter interactions in quantum electrodynamics typically invoke the dipole approximation1,2, in which atoms are treated as point-like objects when compared to the wavelength of the electromagnetic modes with which they interact. However, when the ratio between the size of the atom and the mode wavelength is increased, the dipole approximation no longer holds and the atom is referred to as a ‘giant atom’2,3. So far, experimental studies with solid-state devices in the giant-atom regime have been limited to superconducting qubits that couple to short-wavelength surface acoustic waves4,5,6,7,8,9,10, probing the properties of the atom at only a single frequency. Here we use an alternative architecture that realizes a giant atom by coupling small atoms to a waveguide at multiple, but well separated, discrete locations. This system enables tunable atom–waveguide couplings with large on–off ratios3 and a coupling spectrum that can be engineered by the design of the device. We also demonstrate decoherence-free interactions between multiple giant atoms that are mediated by the quasi-continuous spectrum of modes in the waveguide—an effect that is not achievable using small atoms11. These features allow qubits in this architecture to switch between protected and emissive configurations in situ while retaining qubit–qubit interactions, opening up possibilities for high-fidelity quantum simulations and non-classical itinerant photon generation12,13.
- Top Cited Papers
- 1 June 2019
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 6 (2) , 021318
A quantum engineer's guide to superconducting qubits
The aim of this review is to provide quantum engineers with an introductory guide to the central concepts and challenges in the rapidly accelerating field of superconducting quantum circuits. Over the past twenty years, the field has matured from a predominantly basic research endeavor to a one that increasingly explores the engineering of larger-scale superconducting quantum systems. Here, we review several foundational elements—qubit design, noise properties, qubit control, and readout techniques—developed during this period, bridging fundamental concepts in circuit quantum electrodynamics and contemporary, state-of-the-art applications in gate-model quantum computation.
- 1 June 2019
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 6 (2) , 021318
Top Cited PapersA quantum engineer's guide to superconducting qubits
The aim of this review is to provide quantum engineers with an introductory guide to the central concepts and challenges in the rapidly accelerating field of superconducting quantum circuits. Over the past twenty years, the field has matured from a predominantly basic research endeavor to a one that increasingly explores the engineering of larger-scale superconducting quantum systems. Here, we review several foundational elements—qubit design, noise properties, qubit control, and readout techniques—developed during this period, bridging fundamental concepts in circuit quantum electrodynamics and contemporary, state-of-the-art applications in gate-model quantum computation.