Felipe Murphy Armando
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Felipe Murphy Armando has a total of 180 co-authors. Here are the top co-authors by number of shared publications:
S. Fahy
Tyndall National Institute University College Cork Ireland
12 shared publications- Ivana Savić
King's College London
4 shared publications - Michael Brian Clavel
Advanced Devices and Sustainable Energy Laboratory (ADSEL), Bradley Department of Electrical and Computer Engineering, Virginia Tech, Blacksburg, Virginia 24061, United States
4 shared publications Chang Liu
School of Electronic Science and Engineering Nanjing University 22 Hankou Rd Nanjing 210093 China
3 shared publicationsDzianis Saladukha
Tyndall National Institute (Ireland)
3 shared publications- Ray Duffy
Tyndall National Institute University College Cork Cork Ireland
3 shared publications
Latest Publications
- 23 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (25)
Gate-induced electron transfer effects in monolithic Al–Ge–Al nanostructures
Germanium (Ge) is recognized as a highly promising substrate for a broad spectrum of electronic, optical, and quantum applications, owing to its exceptional properties, including high charge carrier mobility, strong spin-orbit coupling, and its behavior as a quasi-direct semiconductor. However, the electron transfer effect in Ge, similar to the Gunn effect in GaAs, which induces negative differential resistance, has received relatively little attention thus far. This is likely due to the requirement for a well-defined material system and device architecture for its realization and usually at low temperatures.
- 23 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (25)
Gate-induced electron transfer effects in monolithic Al–Ge–Al nanostructures
Germanium (Ge) is recognized as a highly promising substrate for a broad spectrum of electronic, optical, and quantum applications, owing to its exceptional properties, including high charge carrier mobility, strong spin-orbit coupling, and its behavior as a quasi-direct semiconductor. However, the electron transfer effect in Ge, similar to the Gunn effect in GaAs, which induces negative differential resistance, has received relatively little attention thus far. This is likely due to the requirement for a well-defined material system and device architecture for its realization and usually at low temperatures.
- Open Access
First-Principles Calculation of Spin-Relaxation Due to Alloy and Electron-Phonon Scattering in Strained GeSn
GeSn has emerged as a promising material for spintronics due to its long spin-lifetime, compatibility with silicon technology, high mobility and tunable electronic properties. Of particular interest is the transition from an indirect to a direct band gap with increasing Sn content, which enhances optical properties, electron transport and we find also affects spin transport behaviour, which is critical for spintronics applications. We use first-principles electronic-structure theory to determine the spin-flip electron-alloy scattering parameters in n-type GeSn alloys. We also calculate the previously undetermined intervalley electron spin-phonon scattering parameters between the $L$ and $Γ$ valleys. These parameters are used to determine the electron-alloy and electron-phonon scattering contributions to the n-type spin-relaxation of GeSn, as a function of alloy content and temperature. As in the case of phonon scattering, alloy scattering reduces the spin-relaxation time. However, switching the spin transport from the typical $L$ valley of Ge to the $Γ$ valley by sufficient addition of Sn, the relaxation time can be substantially increased. For unstrained, room temperature GeSn, we find a Sn concentration of at least $10\%$ is required to achieve a spin-relaxation time greater than Ge, with $17\%$ Sn needed to increase the spin-relaxation time from the nanosecond range to the microsecond range. At low temperatures (30K), adding $10\%$ Sn can increase the spin-relaxation time from $10^{-7}$s to 0.1s. Applying biaxial tensile strain to GeSn further increases the spin-relaxation time and at a lower Sn content than in unstrained GeSn.Open AccessFirst-Principles Calculation of Spin-Relaxation Due to Alloy and Electron-Phonon Scattering in Strained GeSn
GeSn has emerged as a promising material for spintronics due to its long spin-lifetime, compatibility with silicon technology, high mobility and tunable electronic properties. Of particular interest is the transition from an indirect to a direct band gap with increasing Sn content, which enhances optical properties, electron transport and we find also affects spin transport behaviour, which is critical for spintronics applications. We use first-principles electronic-structure theory to determine the spin-flip electron-alloy scattering parameters in n-type GeSn alloys. We also calculate the previously undetermined intervalley electron spin-phonon scattering parameters between the $L$ and $Γ$ valleys. These parameters are used to determine the electron-alloy and electron-phonon scattering contributions to the n-type spin-relaxation of GeSn, as a function of alloy content and temperature. As in the case of phonon scattering, alloy scattering reduces the spin-relaxation time. However, switching the spin transport from the typical $L$ valley of Ge to the $Γ$ valley by sufficient addition of Sn, the relaxation time can be substantially increased. For unstrained, room temperature GeSn, we find a Sn concentration of at least $10\%$ is required to achieve a spin-relaxation time greater than Ge, with $17\%$ Sn needed to increase the spin-relaxation time from the nanosecond range to the microsecond range. At low temperatures (30K), adding $10\%$ Sn can increase the spin-relaxation time from $10^{-7}$s to 0.1s. Applying biaxial tensile strain to GeSn further increases the spin-relaxation time and at a lower Sn content than in unstrained GeSn. - 10 February 2025
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 162 (6)
Ultrafast dynamics of hot carriers: Theoretical approaches based on real-time propagation of carrier distributions
In recent years, computational approaches which couple density functional theory (DFT)-based description of the electron–phonon and phonon–phonon scattering rates with the Boltzmann transport equation have been shown to obtain the electron and thermal transport characteristics of many 3D and 2D semiconductors in excellent agreement with experimental measurements. At the same time, progress in the DFT-based description of the electron–phonon scattering has also allowed to describe the non-equilibrium relaxation dynamics of hot or photo-excited electrons in several materials, in very good agreement with time-resolved spectroscopy experiments. In the latter case, as the time-resolved spectroscopy techniques provide the possibility to monitor transient material characteristics evolving on the femtosecond and attosecond time scales, the time evolution of photo-excited, nonthermal carrier distributions has to be described. Similarly, reliable theoretical approaches are needed to describe the transient transport properties of devices involving high energy carriers. In this review, we aim to discuss recent progress in coupling the ab initio description of materials, especially that of the electron–phonon scattering, with the time-dependent approaches describing the time evolution of the out-of-equilibrium carrier distributions, in the context of time-resolved spectroscopy experiments as well as in the context of transport simulations. We point out the computational limitations common to all numerical approaches, which describe time propagation of strongly out-of-equilibrium carrier distributions in 3D materials, and discuss the methods used to overcome them.
- 10 February 2025
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 162 (6)
Ultrafast dynamics of hot carriers: Theoretical approaches based on real-time propagation of carrier distributions
In recent years, computational approaches which couple density functional theory (DFT)-based description of the electron–phonon and phonon–phonon scattering rates with the Boltzmann transport equation have been shown to obtain the electron and thermal transport characteristics of many 3D and 2D semiconductors in excellent agreement with experimental measurements. At the same time, progress in the DFT-based description of the electron–phonon scattering has also allowed to describe the non-equilibrium relaxation dynamics of hot or photo-excited electrons in several materials, in very good agreement with time-resolved spectroscopy experiments. In the latter case, as the time-resolved spectroscopy techniques provide the possibility to monitor transient material characteristics evolving on the femtosecond and attosecond time scales, the time evolution of photo-excited, nonthermal carrier distributions has to be described. Similarly, reliable theoretical approaches are needed to describe the transient transport properties of devices involving high energy carriers. In this review, we aim to discuss recent progress in coupling the ab initio description of materials, especially that of the electron–phonon scattering, with the time-dependent approaches describing the time evolution of the out-of-equilibrium carrier distributions, in the context of time-resolved spectroscopy experiments as well as in the context of transport simulations. We point out the computational limitations common to all numerical approaches, which describe time propagation of strongly out-of-equilibrium carrier distributions in 3D materials, and discuss the methods used to overcome them.
- Open Access
- 28 January 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 23 (1)
First-principles calculation of alloy scattering and -type mobility in strainedWe use first-principles electronic-structure theory to determine the intra- and intervalley electron-alloy scattering parameters in -type Ge − Sn alloys. These parameters are used to determine the alloy scattering contributions to the -type electron mobility of Ge − Sn at 300 and 15 K using a first iteration of the Boltzmann transport equation in the relaxation-time approximation. For unstrained Ge − Sn , we find that an Sn concentration of at least 13.5 % is needed to achieve an electron mobility greater than that of Ge . Our results show that the mobility of Ge − Sn can be over 25 times that of Ge , or 10 5 cm 2 /(Vs). At 15 K , incorporation of less than 6 % Sn into Ge quadruples its mobility, which suggests that Ge − Sn has potential applications as a high-mobility 2D electron gas. Applying biaxial tensile strain to Ge − Sn further increases the mobility and achieves this improvement at lower Sn content than in unstrained Ge − Sn .
- 28 January 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 23 (1)
Open AccessFirst-principles calculation of alloy scattering and -type mobility in strainedWe use first-principles electronic-structure theory to determine the intra- and intervalley electron-alloy scattering parameters in -type Ge − Sn alloys. These parameters are used to determine the alloy scattering contributions to the -type electron mobility of Ge − Sn at 300 and 15 K using a first iteration of the Boltzmann transport equation in the relaxation-time approximation. For unstrained Ge − Sn , we find that an Sn concentration of at least 13.5 % is needed to achieve an electron mobility greater than that of Ge . Our results show that the mobility of Ge − Sn can be over 25 times that of Ge , or 10 5 cm 2 /(Vs). At 15 K , incorporation of less than 6 % Sn into Ge quadruples its mobility, which suggests that Ge − Sn has potential applications as a high-mobility 2D electron gas. Applying biaxial tensile strain to Ge − Sn further increases the mobility and achieves this improvement at lower Sn content than in unstrained Ge − Sn .
- Open Access
First-Principles Calculation of Alloy Scattering and n-type Mobility in Strained GeSn
We use first-principles electronic-structure theory to determine the intra- and inter-valley electron-alloy scattering parameters in n-type GeSn alloys. These parameters are used to determine the alloy scattering contributions to the n-type electron mobility of GeSn at $300K$ and $15K$ using a first iteration of the Boltzmann transport equation in the relaxation time approximation. For unstrained GeSn, we find that a Sn concentration of at least $13.5\%$ is needed to achieve an electron mobility greater than that of Ge. Our results show that the mobility of GeSn can be over $25$ times higher than the mobility of Ge, or $10^5$ cm$^2$/(Vs). At $15K$, less than $6\%$ Sn incorporation into Ge quadruples its mobility, which suggests GeSn has potential applications as a high mobility 2D electron gas. Applying biaxial tensile strain to GeSn further increases the mobility and at a lower Sn content than in unstrained GeSn.Open AccessFirst-Principles Calculation of Alloy Scattering and n-type Mobility in Strained GeSn
We use first-principles electronic-structure theory to determine the intra- and inter-valley electron-alloy scattering parameters in n-type GeSn alloys. These parameters are used to determine the alloy scattering contributions to the n-type electron mobility of GeSn at $300K$ and $15K$ using a first iteration of the Boltzmann transport equation in the relaxation time approximation. For unstrained GeSn, we find that a Sn concentration of at least $13.5\%$ is needed to achieve an electron mobility greater than that of Ge. Our results show that the mobility of GeSn can be over $25$ times higher than the mobility of Ge, or $10^5$ cm$^2$/(Vs). At $15K$, less than $6\%$ Sn incorporation into Ge quadruples its mobility, which suggests GeSn has potential applications as a high mobility 2D electron gas. Applying biaxial tensile strain to GeSn further increases the mobility and at a lower Sn content than in unstrained GeSn. - Open Access
- 14 October 2024
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 19 (1)
Strain‐Induced Effects on Band‐to‐Band Tunneling and Trap‐Assisted Tunneling in Si Examined by Experiment and Theory
Strain is commonly used in metal–oxide–semiconductor technologies to boost on‐state performance. This booster has been in production for at least a decade. Despite this, a systematic study of the impact of strain on off‐state leakage current has been lacking. Herein, experimental data and ab initio calculations are used to refine existing models to account for the impact of strain on band‐to‐band tunneling and trap‐assisted tunneling in silicon. It is observed that the strain may dramatically increase the leakage current, depending on the type of tunneling involved. For band‐to‐band and trap‐assisted tunneling, low uniaxial strains of 0.1% (or 180 MPa) can increase the leakage current by 60% and 10% compared to the unstrained case, respectively. Using models, it is predicted that compressive strain on the order of 1% (or 2 GPa) can increase the leakage current by 150 times. Conversely, tensile strain may diminish or at most double the leakage current in all observed cases. Though detrimental in conventional inversion‐mode metal‐oxide‐semiconductor field‐effect‐transistor, these processes may be used to boost the performance of tunnel field‐effect transistors, where on‐state current is defined by band‐to‐band tunneling.
- 14 October 2024
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 19 (1)
Open AccessStrain‐Induced Effects on Band‐to‐Band Tunneling and Trap‐Assisted Tunneling in Si Examined by Experiment and Theory
Strain is commonly used in metal–oxide–semiconductor technologies to boost on‐state performance. This booster has been in production for at least a decade. Despite this, a systematic study of the impact of strain on off‐state leakage current has been lacking. Herein, experimental data and ab initio calculations are used to refine existing models to account for the impact of strain on band‐to‐band tunneling and trap‐assisted tunneling in silicon. It is observed that the strain may dramatically increase the leakage current, depending on the type of tunneling involved. For band‐to‐band and trap‐assisted tunneling, low uniaxial strains of 0.1% (or 180 MPa) can increase the leakage current by 60% and 10% compared to the unstrained case, respectively. Using models, it is predicted that compressive strain on the order of 1% (or 2 GPa) can increase the leakage current by 150 times. Conversely, tensile strain may diminish or at most double the leakage current in all observed cases. Though detrimental in conventional inversion‐mode metal‐oxide‐semiconductor field‐effect‐transistor, these processes may be used to boost the performance of tunnel field‐effect transistors, where on‐state current is defined by band‐to‐band tunneling.
- Open Access
- 22 May 2023
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 5 (2) , L022035
Quantum spin Hall phase in GeSn heterostructures on silicon
Quantum phases of solid-state electron systems can sustain exotic phenomena and a very rich spin physics. We utilize model-solid theory to show that alloys, an emerging group IV semiconductor, can be engineered into heterostructures that demonstrate a broken-gap alignment. Furthermore, the eight-band method is used to disclose a quantum spin Hall phase in heterojunctions that accommodates the existence of gate-controlled chiral edge states. This proposal introduces a practical silicon-based architecture that spontaneously sustains topological properties, while being compatible with the high-volume manufacture of semiconductor technologies.- 22 May 2023
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 5 (2) , L022035
Open AccessQuantum spin Hall phase in GeSn heterostructures on silicon
Quantum phases of solid-state electron systems can sustain exotic phenomena and a very rich spin physics. We utilize model-solid theory to show that alloys, an emerging group IV semiconductor, can be engineered into heterostructures that demonstrate a broken-gap alignment. Furthermore, the eight-band method is used to disclose a quantum spin Hall phase in heterojunctions that accommodates the existence of gate-controlled chiral edge states. This proposal introduces a practical silicon-based architecture that spontaneously sustains topological properties, while being compatible with the high-volume manufacture of semiconductor technologies. - Open Access
- 2 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (1) , 012202
Electronic heat generation in semiconductors: Non-equilibrium excitation and evolution of zone-edge phonons via electron–phonon scattering in photo-excited germanium
We investigate experimentally and using first-principles theory the generation of phonons and the relaxation of carriers on picosecond timescales across the Brillouin zone of photo-excited Ge by inter-valley electron–phonon scattering. The phonons generated are typical of those generated in semiconductor devices, contributing to the accumulation of heat within the material. We simulate the time-evolution of phonon populations, based on first-principles band structure and electron–phonon and phonon–phonon matrix elements, and compare them to data from time-resolved x-ray diffuse scattering experiments, performed at the Linac Coherent Light Source x-ray free-electron laser facility, following photo-excitation by a 50 fs near-infrared optical pulse. We show that the intensity of the non-thermal x-ray diffuse scattering signal, which is observed to grow substantially near the L-point of the Brillouin zone over 3–5 ps, is due to phonons generated by scattering of carriers between the Δ and L valleys. These phonons have low group velocities, resulting in a heat bottleneck. With the inclusion of phonon decay through 3-phonon processes, the simulations also account for other non-thermal features observed in the x-ray diffuse scattering intensity, which are due to anharmonic phonon–phonon scattering of the phonons initially generated by electron–phonon scattering.
- 2 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (1) , 012202
Open AccessElectronic heat generation in semiconductors: Non-equilibrium excitation and evolution of zone-edge phonons via electron–phonon scattering in photo-excited germanium
We investigate experimentally and using first-principles theory the generation of phonons and the relaxation of carriers on picosecond timescales across the Brillouin zone of photo-excited Ge by inter-valley electron–phonon scattering. The phonons generated are typical of those generated in semiconductor devices, contributing to the accumulation of heat within the material. We simulate the time-evolution of phonon populations, based on first-principles band structure and electron–phonon and phonon–phonon matrix elements, and compare them to data from time-resolved x-ray diffuse scattering experiments, performed at the Linac Coherent Light Source x-ray free-electron laser facility, following photo-excitation by a 50 fs near-infrared optical pulse. We show that the intensity of the non-thermal x-ray diffuse scattering signal, which is observed to grow substantially near the L-point of the Brillouin zone over 3–5 ps, is due to phonons generated by scattering of carriers between the Δ and L valleys. These phonons have low group velocities, resulting in a heat bottleneck. With the inclusion of phonon decay through 3-phonon processes, the simulations also account for other non-thermal features observed in the x-ray diffuse scattering intensity, which are due to anharmonic phonon–phonon scattering of the phonons initially generated by electron–phonon scattering.
- 27 December 2022
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 18 (6) , 064083
Multivalley Electron Conduction at the Indirect-Direct Crossover Point in Highly Tensile-Strained Germanium
As forward-looking electron devices increasingly adopt high-mobility low-band-gap materials, such as germanium (), questions remain regarding the feasibility of strain engineering in low-band-gap systems. Particularly, the L-Γ valley separation (∼150 meV) can be overcome by introducing a high degree of tensile strain (ε ≥ 1.5%). It is therefore essential to understand the nature of highly strained transport, wherein multivalley electron conduction becomes a possibility. Here, we report on the competitiveness between L- and Γ-valley transport in highly tensile-strained (ε ∼ 1.6%) heterostructures. Temperature-dependent magnetotransport analysis reveals two contributing carrier populations, identified as lower- and higher-mobility L- and Γ-valley electrons (in ), using temperature-dependent Boltzmann transport modeling. Coupling this interpretation with electron-cyclotron-resonance studies, the effective mass (m*) of the higher-mobility Γ-valley electrons is probed, revealing m* = (0.049 ± 0.007). Moreover, a comparison of empirical and theoretical m* indicates that these electrons reside primarily in the first-two quantum sublevels of the Γ valley. Consequently, our results provide an insight into the strain-dependent carrier dynamics of , offering alternative pathways toward efficacious strain engineering.- 27 December 2022
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 18 (6) , 064083
Multivalley Electron Conduction at the Indirect-Direct Crossover Point in Highly Tensile-Strained Germanium
As forward-looking electron devices increasingly adopt high-mobility low-band-gap materials, such as germanium (), questions remain regarding the feasibility of strain engineering in low-band-gap systems. Particularly, the L-Γ valley separation (∼150 meV) can be overcome by introducing a high degree of tensile strain (ε ≥ 1.5%). It is therefore essential to understand the nature of highly strained transport, wherein multivalley electron conduction becomes a possibility. Here, we report on the competitiveness between L- and Γ-valley transport in highly tensile-strained (ε ∼ 1.6%) heterostructures. Temperature-dependent magnetotransport analysis reveals two contributing carrier populations, identified as lower- and higher-mobility L- and Γ-valley electrons (in ), using temperature-dependent Boltzmann transport modeling. Coupling this interpretation with electron-cyclotron-resonance studies, the effective mass (m*) of the higher-mobility Γ-valley electrons is probed, revealing m* = (0.049 ± 0.007). Moreover, a comparison of empirical and theoretical m* indicates that these electrons reside primarily in the first-two quantum sublevels of the Γ valley. Consequently, our results provide an insight into the strain-dependent carrier dynamics of , offering alternative pathways toward efficacious strain engineering.- Open Access
- 25 February 2021
- Published by American Physical Society (APS) in Physical Review B
- Vol. 103 (8) , 085310
Light emission from direct band gap germanium containing split-interstitial defects
The lack of useful and cost-efficient group-IV direct band gap light emitters still presents the main bottleneck for complementary metal-oxide semiconductor-compatible short-distance data transmission, single-photon emission, and sensing based on silicon photonics. Germanium, a group-IV element like Si, is already widely used in silicon fabs. While the energy band gap of Ge is intrinsically indirect, we predict that the insertion of Ge-Ge split-[110] interstitials into crystalline Ge can open up a direct band gap transmission path. Here, we calculate from first principles the band structure and optical emission properties of Ge, Sb, and Sn split-[110] interstitials in bulk and low-dimensional Ge at different doping concentrations. Two types of electronic states provide the light-emission enhancement below the direct band gap of Ge: a hybridized L- state at the Brillouin zone center and a conduction band of band character that couples to a raised valence band along the -X direction. Majority carrier introduced to the system through doping can enhance light emission by saturation of nonradiative paths. Ge-Sn split interstitials in Ge shift the top of the valence band towards the -X direction and increase the character of the L- state, which results in a shift to longer emission wavelengths. Key spectral regions for datacom and sensing applications can be covered by applying quantum confinement in defect-enhanced Ge quantum dots for an emission wavelength shift from the midinfrared to the telecom regime.- 25 February 2021
- Published by American Physical Society (APS) in Physical Review B
- Vol. 103 (8) , 085310
Open AccessLight emission from direct band gap germanium containing split-interstitial defects
The lack of useful and cost-efficient group-IV direct band gap light emitters still presents the main bottleneck for complementary metal-oxide semiconductor-compatible short-distance data transmission, single-photon emission, and sensing based on silicon photonics. Germanium, a group-IV element like Si, is already widely used in silicon fabs. While the energy band gap of Ge is intrinsically indirect, we predict that the insertion of Ge-Ge split-[110] interstitials into crystalline Ge can open up a direct band gap transmission path. Here, we calculate from first principles the band structure and optical emission properties of Ge, Sb, and Sn split-[110] interstitials in bulk and low-dimensional Ge at different doping concentrations. Two types of electronic states provide the light-emission enhancement below the direct band gap of Ge: a hybridized L- state at the Brillouin zone center and a conduction band of band character that couples to a raised valence band along the -X direction. Majority carrier introduced to the system through doping can enhance light emission by saturation of nonradiative paths. Ge-Sn split interstitials in Ge shift the top of the valence band towards the -X direction and increase the character of the L- state, which results in a shift to longer emission wavelengths. Key spectral regions for datacom and sensing applications can be covered by applying quantum confinement in defect-enhanced Ge quantum dots for an emission wavelength shift from the midinfrared to the telecom regime.