Rifaqat Ali Khan Rao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Rifaqat Ali Khan Rao has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Mohammad Ajmal
Environmental Research Laboratory, Department of Applied Chemistry , Aligarh Muslim University , Aligarh, India
9 shared publications- Mohammad Kashif Uddin
Department of Chemistry, College of Science, Majmaah University, Al-Majmaah, Saudi Arabia
8 shared publications Fouzia Rehman
Environmental Research Laboratory, Department of Applied Chemistry, Faculty of Engineering and Technology , Aligarh Muslim University , Aligarh , 202002 , UP , India Phone: Tel. +91 0571 2703167x3000
6 shared publicationsJameel Ahmad
5 shared publicationsMoonis Ali Khan
Department of Environmental Engineering, Yonsei University, Wonju, Gangwon-do 220-710, South Korea
5 shared publications- Moonis Ali Khan
Department of Chemistry, College of Science, King Saud University, Riyadh, Saudi Arabia
3 shared publications
Latest Publications
- 1 August 2018
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 11, 1-14
Adsorptive remediation of Pb(II) from aqueous media using Schleichera oleosa bark
- 1 August 2018
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 11, 1-14
Adsorptive remediation of Pb(II) from aqueous media using Schleichera oleosa bark
- Top Cited PapersOpen Access
- 16 February 2018
- Published by Springer Nature in Journal of Nanobiotechnology
- Vol. 16 (1) , 1-28
A review on biosynthesis of silver nanoparticles and their biocidal properties
Use of silver and silver salts is as old as human civilization but the fabrication of silver nanoparticles (Ag NPs) has only recently been recognized. They have been specifically used in agriculture and medicine as antibacterial, antifungal and antioxidants. It has been demonstrated that Ag NPs arrest the growth and multiplication of many bacteria such as Bacillus cereus, Staphylococcus aureus, Citrobacter koseri, Salmonella typhii, Pseudomonas aeruginosa, Escherichia coli, Klebsiella pneumonia, Vibrio parahaemolyticus and fungus Candida albicans by binding Ag/Ag+ with the biomolecules present in the microbial cells. It has been suggested that Ag NPs produce reactive oxygen species and free radicals which cause apoptosis leading to cell death preventing their replication. Since Ag NPs are smaller than the microorganisms, they diffuse into cell and rupture the cell wall which has been shown from SEM and TEM images of the suspension containing nanoparticles and pathogens. It has also been shown that smaller nanoparticles are more toxic than the bigger ones. Ag NPs are also used in packaging to prevent damage of food products by pathogens. The toxicity of Ag NPs is dependent on the size, concentration, pH of the medium and exposure time to pathogens.
- 16 February 2018
- Published by Springer Nature in Journal of Nanobiotechnology
- Vol. 16 (1) , 1-28
Top Cited PapersOpen AccessA review on biosynthesis of silver nanoparticles and their biocidal properties
Use of silver and silver salts is as old as human civilization but the fabrication of silver nanoparticles (Ag NPs) has only recently been recognized. They have been specifically used in agriculture and medicine as antibacterial, antifungal and antioxidants. It has been demonstrated that Ag NPs arrest the growth and multiplication of many bacteria such as Bacillus cereus, Staphylococcus aureus, Citrobacter koseri, Salmonella typhii, Pseudomonas aeruginosa, Escherichia coli, Klebsiella pneumonia, Vibrio parahaemolyticus and fungus Candida albicans by binding Ag/Ag+ with the biomolecules present in the microbial cells. It has been suggested that Ag NPs produce reactive oxygen species and free radicals which cause apoptosis leading to cell death preventing their replication. Since Ag NPs are smaller than the microorganisms, they diffuse into cell and rupture the cell wall which has been shown from SEM and TEM images of the suspension containing nanoparticles and pathogens. It has also been shown that smaller nanoparticles are more toxic than the bigger ones. Ag NPs are also used in packaging to prevent damage of food products by pathogens. The toxicity of Ag NPs is dependent on the size, concentration, pH of the medium and exposure time to pathogens.
- Open Access
- 1 November 2016
- Published by Scientific Scholar in Arabian Journal of Chemistry
- Vol. 9, S1233-S1241
Adsorption studies of Cd(II) on ball clay: Comparison with other natural clays
Ball clay was found to exhibit excellent adsorption capacity toward Cd(II) ions over a wide concentration range. The adsorption capacity was studied by heating it at different temperatures. It was found that the sample heated at 200°C showed maximum adsorption capacity toward Cd(II) ions. This research was focused on the effect of pH, time, temperature, adsorbent doses and initial Cd(II) concentration by batch experiments. The equilibrium data of Cd(II) adsorption were explained well by Langmuir and Freundlich adsorption isotherms. The kinetics data for the adsorption process obeyed pseudo-first-order and pseudo-second-order models at lower initial concentrations of Cd(II) while with the increased concentration of Cd(II) pseudo-first-order model failed. The Cd(II) desorption was performed using batch process with various desorbing solutions and 100% desorption was achieved with HCl solution
- 1 November 2016
- Published by Scientific Scholar in Arabian Journal of Chemistry
- Vol. 9, S1233-S1241
Open AccessAdsorption studies of Cd(II) on ball clay: Comparison with other natural clays
Ball clay was found to exhibit excellent adsorption capacity toward Cd(II) ions over a wide concentration range. The adsorption capacity was studied by heating it at different temperatures. It was found that the sample heated at 200°C showed maximum adsorption capacity toward Cd(II) ions. This research was focused on the effect of pH, time, temperature, adsorbent doses and initial Cd(II) concentration by batch experiments. The equilibrium data of Cd(II) adsorption were explained well by Langmuir and Freundlich adsorption isotherms. The kinetics data for the adsorption process obeyed pseudo-first-order and pseudo-second-order models at lower initial concentrations of Cd(II) while with the increased concentration of Cd(II) pseudo-first-order model failed. The Cd(II) desorption was performed using batch process with various desorbing solutions and 100% desorption was achieved with HCl solution
- 30 August 2016
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 52 (3) , 435-446
Sorption studies for Cd(II) sequestration from aqueous solution on chemically modified Albizia lebbeck
In the present work, a new sorbent was successfully prepared by chemically modifying pods of Albizia lebbeck (AL) by Fenton’s reagent, followed by sodium silicate. Sorption studies were carried out by batch process. The optimum pH was found to be 6. Equilibrium isotherm data were analysed by non-linear curve fitting analysis, to fit Langmuir, Freundlich and Temkin isotherm models. Based on the Langmuir isotherm model, maximum monolayer sorption capacity (qm) was found to be 21.22 mg.g−1 at 50°C. Breakthrough and exhaustive capacities were found to be 10 and 50 mg.g−1, respectively. Desorption study showed 95% recovery of Cd(II) ions.
- 30 August 2016
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 52 (3) , 435-446
Sorption studies for Cd(II) sequestration from aqueous solution on chemically modified Albizia lebbeck
In the present work, a new sorbent was successfully prepared by chemically modifying pods of Albizia lebbeck (AL) by Fenton’s reagent, followed by sodium silicate. Sorption studies were carried out by batch process. The optimum pH was found to be 6. Equilibrium isotherm data were analysed by non-linear curve fitting analysis, to fit Langmuir, Freundlich and Temkin isotherm models. Based on the Langmuir isotherm model, maximum monolayer sorption capacity (qm) was found to be 21.22 mg.g−1 at 50°C. Breakthrough and exhaustive capacities were found to be 10 and 50 mg.g−1, respectively. Desorption study showed 95% recovery of Cd(II) ions.
- Open Access
- 1 August 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (38) , 17808-17825
Application of Terminalia arjuna as potential adsorbent for the removal of Pb(II) from aqueous solution: thermodynamics, kinetics and process design
The present work explored the adsorption properties of Terminalia arjuna fruit powder for the removal of Pb(II) from aqueous solution. Effect of concentration, contact time, pH, adsorbent dose, and temperature were studied using batch process to optimize conditions for maximum adsorption of Pb(II). Kinetic data showed that the pseudo-second-order model was the best fit for the experimental data over a wide range of concentrations. Thermodynamic parameters (∆H° and ∆G°) suggested endothermic and spontaneous nature of adsorption. Mean free energies at different temperatures were in between 10.1 and 14.3 kJ mol−1 indicating chemical nature of adsorption process. Equilibrium isotherm data were analyzed using Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D–R) isotherms models at 30, 40, and 50°C. The breakthrough and exhaustive capacities were found to be 5 and 15 mg g−1, respectively. Desorption studies were carried out by column method and 84% of Pb(II) ions were recovered when 0.05 N HCl was used. A single-stage batch adsorption design was proposed to predict the amount of adsorbent required for 98% removal of Pb(II) from different volumes of water.
- 1 August 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (38) , 17808-17825
Open AccessApplication of Terminalia arjuna as potential adsorbent for the removal of Pb(II) from aqueous solution: thermodynamics, kinetics and process design
The present work explored the adsorption properties of Terminalia arjuna fruit powder for the removal of Pb(II) from aqueous solution. Effect of concentration, contact time, pH, adsorbent dose, and temperature were studied using batch process to optimize conditions for maximum adsorption of Pb(II). Kinetic data showed that the pseudo-second-order model was the best fit for the experimental data over a wide range of concentrations. Thermodynamic parameters (∆H° and ∆G°) suggested endothermic and spontaneous nature of adsorption. Mean free energies at different temperatures were in between 10.1 and 14.3 kJ mol−1 indicating chemical nature of adsorption process. Equilibrium isotherm data were analyzed using Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D–R) isotherms models at 30, 40, and 50°C. The breakthrough and exhaustive capacities were found to be 5 and 15 mg g−1, respectively. Desorption studies were carried out by column method and 84% of Pb(II) ions were recovered when 0.05 N HCl was used. A single-stage batch adsorption design was proposed to predict the amount of adsorbent required for 98% removal of Pb(II) from different volumes of water.
- Open Access
- 9 February 2016
- Published by Springer Nature in Applied Water Science
- Vol. 7 (4) , 2051-2061
Adsorption studies of Cu(II) on Boston fern (Nephrolepis exaltata Schott cv. Bostoniensis) leaves
- 9 February 2016
- Published by Springer Nature in Applied Water Science
- Vol. 7 (4) , 2051-2061
Open AccessAdsorption studies of Cu(II) on Boston fern (Nephrolepis exaltata Schott cv. Bostoniensis) leaves
- 7 January 2016
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 8 (4) , 869-879
Nylon 6,6 based fibrous composite: preparation, characterization and its utilization for the removal of hazardous Cr(vi) from aqueous solution
This study reports the synthesis of nylon 6,6-zirconium(IV)selenite (N6/ZS) fibrous composite as a promising adsorbent for the removal of Cr(VI), a known carcinogen and hazardous heavy metal. The formation of the N6/ZS composite was confirmed by Fourier transform infra-red spectroscopy (FTIR), Scanning electron microscopy (SEM), Energy-dispersive X-ray (EDX) and X-ray diffraction (XRD). The composite showed appreciable adsorption of Cr(VI). In addition, batch adsorption studies concerning the effect of pH, contact time, initial Cr(VI) concentration and temperature were performed. The monolayer adsorption capacity calculated from the Langmuir model for N6/ZS was found to be 59.171 mg g−1 at 50 °C and the negative free energy change confirms the adsorption of Cr(VI) as a spontaneous and endothermic process. The adsorption rate was considerably fast and followed pseudo-second-order kinetics suggesting that the adsorption mainly consisted of chemisorption. The intra-particle diffusion model indicated that intra-particle diffusion was not only the rate limiting step and hence, the adsorption of Cr(VI) was chemical in nature. Also, the adsorbent could be effectively regenerated and showed good reusability. The facile synthesis and the robust adsorption performance of this fibrous composite can reveal new avenues for the removal of environmental hazards.
- 7 January 2016
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 8 (4) , 869-879
Nylon 6,6 based fibrous composite: preparation, characterization and its utilization for the removal of hazardous Cr(vi) from aqueous solution
This study reports the synthesis of nylon 6,6-zirconium(IV)selenite (N6/ZS) fibrous composite as a promising adsorbent for the removal of Cr(VI), a known carcinogen and hazardous heavy metal. The formation of the N6/ZS composite was confirmed by Fourier transform infra-red spectroscopy (FTIR), Scanning electron microscopy (SEM), Energy-dispersive X-ray (EDX) and X-ray diffraction (XRD). The composite showed appreciable adsorption of Cr(VI). In addition, batch adsorption studies concerning the effect of pH, contact time, initial Cr(VI) concentration and temperature were performed. The monolayer adsorption capacity calculated from the Langmuir model for N6/ZS was found to be 59.171 mg g−1 at 50 °C and the negative free energy change confirms the adsorption of Cr(VI) as a spontaneous and endothermic process. The adsorption rate was considerably fast and followed pseudo-second-order kinetics suggesting that the adsorption mainly consisted of chemisorption. The intra-particle diffusion model indicated that intra-particle diffusion was not only the rate limiting step and hence, the adsorption of Cr(VI) was chemical in nature. Also, the adsorbent could be effectively regenerated and showed good reusability. The facile synthesis and the robust adsorption performance of this fibrous composite can reveal new avenues for the removal of environmental hazards.
- Open Access
- 1 June 2015
- Published by Elsevier in Desalination and Water Treatment
- Vol. 54 (12) , 3358-3371
Removal of Cr(VI) from aqueous solution on seeds of Artimisia absinthium (novel plant material)
Artimisia absinthium, a medicinal plant material, showed excellent adsorption in removing mutagenic Cr(VI) from aqueous solution along with Cu(II), Ni(II), and Zn(II). Various parameters like effect of pH, contact time, temperature, and initial concentration were investigated using batch process to optimize conditions for maximum adsorption. A. absinthium was characterized using scanning electron microscopy (SEM). Adsorption of Cr(VI) was favorable at pH 2 as 96% of Cr(VI) could be removed from aqueous solution. However, adsorption of Cr(VI) decreased to 73% in presence of electrolyte (0.1 N KNO3) at pH 2. The point of zero charge of A. absinthium was 3.9 in double distilled water. The adsorption data were analyzed using Langmuir, Freundlich, Temkin, Hasley, and Dubinin–Redushkeuich isotherm models at 30, 40, and 50°C. The maximum monolayer adsorption capacity towards Cr(VI) was found to be 46.99 mg g−1 at 30°C which was relatively large compared to some other similar adsorbents reported earlier. The kinetic data showed that pseudo-second-order rate equation was better obeyed than pseudo-first-order. The intra-particle diffusion model showed that Cr(VI) adsorption involved three different stages. The breakthrough and exhaustive capacities of the adsorbent were found to be 35 and 45 mg g−1, respectively, at pH 2. Desorption study showed that 93.05% Cr(VI) could be desorbed by column operation with 0.01 N NaOH solution.
- 1 June 2015
- Published by Elsevier in Desalination and Water Treatment
- Vol. 54 (12) , 3358-3371
Open AccessRemoval of Cr(VI) from aqueous solution on seeds of Artimisia absinthium (novel plant material)
Artimisia absinthium, a medicinal plant material, showed excellent adsorption in removing mutagenic Cr(VI) from aqueous solution along with Cu(II), Ni(II), and Zn(II). Various parameters like effect of pH, contact time, temperature, and initial concentration were investigated using batch process to optimize conditions for maximum adsorption. A. absinthium was characterized using scanning electron microscopy (SEM). Adsorption of Cr(VI) was favorable at pH 2 as 96% of Cr(VI) could be removed from aqueous solution. However, adsorption of Cr(VI) decreased to 73% in presence of electrolyte (0.1 N KNO3) at pH 2. The point of zero charge of A. absinthium was 3.9 in double distilled water. The adsorption data were analyzed using Langmuir, Freundlich, Temkin, Hasley, and Dubinin–Redushkeuich isotherm models at 30, 40, and 50°C. The maximum monolayer adsorption capacity towards Cr(VI) was found to be 46.99 mg g−1 at 30°C which was relatively large compared to some other similar adsorbents reported earlier. The kinetic data showed that pseudo-second-order rate equation was better obeyed than pseudo-first-order. The intra-particle diffusion model showed that Cr(VI) adsorption involved three different stages. The breakthrough and exhaustive capacities of the adsorbent were found to be 35 and 45 mg g−1, respectively, at pH 2. Desorption study showed that 93.05% Cr(VI) could be desorbed by column operation with 0.01 N NaOH solution.
- 18 April 2014
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 2 (2) , 1155-1164
Removal of Cd(II) from aqueous solution by exploring the biosorption characteristics of gaozaban (Onosma bracteatum)
- 18 April 2014
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 2 (2) , 1155-1164
Removal of Cd(II) from aqueous solution by exploring the biosorption characteristics of gaozaban (Onosma bracteatum)