Tatiane Marin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Tatiane Marin has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Jacopo Seccatore
Universidad Católica del Norte, Chile
14 shared publications - Giorgio de Tomi
Universidade de São Paulo, Brasil
7 shared publications Marcello Veiga
3 shared publications- Ana Carla de Melo Moreira Campelo
Universidade de São Paulo, Brasil
2 shared publications Giorgio Francesco Cesare de Tomi
2 shared publications- Guillermo Pozo
Department of Metallurgical and Mining Engineering, Universid Catolica del Norte, Antofagasta 1240000, Chile
2 shared publications
Latest Publications
- Open Access
- 3 August 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- Vol. 71 (2) , 219-230
A New Variable for Tunnel Blast Efficiency: the Angles of Breakage of Explosive Charges
Tunnel excavation by drill and blast requires creating an effective opening cut to provide a free surface for subsequent rock breakage. While numerous studies have examined blast design parameters, the exact shape and dimensions of the rock volume assigned to each blasthole have yet to be recognised as critical variables. This study introduces the angle of breakage as a measurable parameter and evaluates its influence on tunnel advance efficiency in blast rounds with parallel-hole cuts. More than 60 tunnel blast designs, as recorded in the Atlas of Blasting Rounds for Tunnel Driving, were analysed. The angles of breakage were determined from blast layouts by using CAD tools and following the delay sequence. Only holes with defined initiation timing were considered. Contour holes and simultaneous delays were excluded. For each blast, the average angle of breakage was calculated and correlated with advance efficiency, defined as the ratio between actual pull (PR) and designed pull (PD). Measured angles ranged from 35° to 140°, with typical industrial averages above 50°. The results show a clear inverse relationship between the average angle of breakage and advance efficiency. A threshold behaviour was identified at approximately 60°, above which efficiency decreases systematically. The highest efficiencies were observed for average angles near 65°. Statistical analysis indicates that the angle of breakage presents a stronger correlation with efficiency (R² up to 0.67 for homogeneous lithological sets) than conventional design parameters such as burden, spacing, powder factor, or hole diameter. Three lithological clusters were identified. A heterogeneous set shows scattered behaviour. A second set, representing the majority of cases across mixed lithologies, exhibits a consistent inverse trend. A third set, composed mainly of competent intrusive igneous rocks, displays a more defined correlation between increasing angle and decreasing efficiency. These results indicate that lithology modulates the sensitivity of efficiency to geometric design parameters. The findings demonstrate that the angle of breakage is a relevant design variable for tunnel blasting. Increasing the angular width of the rock prism assigned to each blasthole increases resistance to breakage and reduces advance efficiency. Blast designs based on narrower angles of breakage provide more favorable conditions for rock fragmentation and displacement. The results support the inclusion of this parameter in blast design methodologies and in the interpretation of tunnel excavation performance.
- 3 August 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- Vol. 71 (2) , 219-230
Open AccessA New Variable for Tunnel Blast Efficiency: the Angles of Breakage of Explosive Charges
Tunnel excavation by drill and blast requires creating an effective opening cut to provide a free surface for subsequent rock breakage. While numerous studies have examined blast design parameters, the exact shape and dimensions of the rock volume assigned to each blasthole have yet to be recognised as critical variables. This study introduces the angle of breakage as a measurable parameter and evaluates its influence on tunnel advance efficiency in blast rounds with parallel-hole cuts. More than 60 tunnel blast designs, as recorded in the Atlas of Blasting Rounds for Tunnel Driving, were analysed. The angles of breakage were determined from blast layouts by using CAD tools and following the delay sequence. Only holes with defined initiation timing were considered. Contour holes and simultaneous delays were excluded. For each blast, the average angle of breakage was calculated and correlated with advance efficiency, defined as the ratio between actual pull (PR) and designed pull (PD). Measured angles ranged from 35° to 140°, with typical industrial averages above 50°. The results show a clear inverse relationship between the average angle of breakage and advance efficiency. A threshold behaviour was identified at approximately 60°, above which efficiency decreases systematically. The highest efficiencies were observed for average angles near 65°. Statistical analysis indicates that the angle of breakage presents a stronger correlation with efficiency (R² up to 0.67 for homogeneous lithological sets) than conventional design parameters such as burden, spacing, powder factor, or hole diameter. Three lithological clusters were identified. A heterogeneous set shows scattered behaviour. A second set, representing the majority of cases across mixed lithologies, exhibits a consistent inverse trend. A third set, composed mainly of competent intrusive igneous rocks, displays a more defined correlation between increasing angle and decreasing efficiency. These results indicate that lithology modulates the sensitivity of efficiency to geometric design parameters. The findings demonstrate that the angle of breakage is a relevant design variable for tunnel blasting. Increasing the angular width of the rock prism assigned to each blasthole increases resistance to breakage and reduces advance efficiency. Blast designs based on narrower angles of breakage provide more favorable conditions for rock fragmentation and displacement. The results support the inclusion of this parameter in blast design methodologies and in the interpretation of tunnel excavation performance.
- 26 May 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 43 (4) , 3557-3566
Impact of Copper Price Variability Compensation Mechanisms on Cut-Off Grade and Economic Extractability of Small-Scale Copper Deposits
- 26 May 2026
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 43 (4) , 3557-3566
Impact of Copper Price Variability Compensation Mechanisms on Cut-Off Grade and Economic Extractability of Small-Scale Copper Deposits
- Open Access
Reduction in Major Greenhouse Gas Emissions in Mineral Comminution Using Ultra-High-Intensity Blasting (UHIB)—A Study for the Chilean Mining Industry
Comminution is the most energy-intensive stage in mineral processing and a major source of indirect greenhouse gas (GHG) emissions in mining. This study evaluates the impact of Ultra-High-Intensity Blasting (UHIB) on downstream comminution energy demand and associated GHG emissions under conditions representative of large-scale Chilean mining. Fragmentation from conventional blasting and UHIB was simulated using JKSimBlast, and the resulting particle size distributions were used as input for four comminution circuit configurations modeled in JKSimMet. Two ore hardness scenarios were analyzed: hard ore (Bond Work Index, BWI = 19 kWh/t) and soft ore (BWI = 11 kWh/t). Power draw of crushers and mills was used to estimate specific energy consumption and GHG emissions based on the Chilean electrical system emission factor. Results show that UHIB enables significant reductions in comminution energy demand, reaching approximately 18% for hard ore and over 30% for soft ore. These reductions are primarily associated with circuit simplification, including the removal of energy-intensive stages such as primary crushing and SAG milling. The results demonstrate that improved fragmentation can reduce downstream energy demand and carbon intensity, highlighting UHIB as an effective mine-to-mill strategy for energy efficiency and emission reduction.
Open AccessReduction in Major Greenhouse Gas Emissions in Mineral Comminution Using Ultra-High-Intensity Blasting (UHIB)—A Study for the Chilean Mining Industry
Comminution is the most energy-intensive stage in mineral processing and a major source of indirect greenhouse gas (GHG) emissions in mining. This study evaluates the impact of Ultra-High-Intensity Blasting (UHIB) on downstream comminution energy demand and associated GHG emissions under conditions representative of large-scale Chilean mining. Fragmentation from conventional blasting and UHIB was simulated using JKSimBlast, and the resulting particle size distributions were used as input for four comminution circuit configurations modeled in JKSimMet. Two ore hardness scenarios were analyzed: hard ore (Bond Work Index, BWI = 19 kWh/t) and soft ore (BWI = 11 kWh/t). Power draw of crushers and mills was used to estimate specific energy consumption and GHG emissions based on the Chilean electrical system emission factor. Results show that UHIB enables significant reductions in comminution energy demand, reaching approximately 18% for hard ore and over 30% for soft ore. These reductions are primarily associated with circuit simplification, including the removal of energy-intensive stages such as primary crushing and SAG milling. The results demonstrate that improved fragmentation can reduce downstream energy demand and carbon intensity, highlighting UHIB as an effective mine-to-mill strategy for energy efficiency and emission reduction.
- Open Access
- 10 March 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (6) , 2630
Experimental Evaluation of Agricultural Ammonium Nitrate as an Explosive in Underground Artisanal Mining
The use of agricultural-grade ammonium nitrate without fuel oil as an explosive has been empirically observed in underground artisanal mining in Ecuador. Despite its practical adoption, the explosive behaviour of this material has not been adequately characterized through experimental measurements. This study presents an experimental evaluation of agricultural ammonium nitrate used as an explosive in underground artisanal mining, with velocity of detonation (VOD) employed as the main control variable. Field-scale experiments were conducted under confined conditions and through in situ measurements in underground production tunnels, using configurations involving ammonium nitrate and commercial emulsion explosives. VOD measurements were performed using a high-sensitivity recording system suitable for short charge lengths. The results show that the emulsion explosive detonated reliably, whereas detonation transferred to the ammonium nitrate column rapidly weakened and collapsed. Detonation propagation within the ammonium nitrate was limited to short distances or extinguished entirely, indicating a non-ideal detonation regime in which sustained propagation cannot be maintained under underground artisanal mining conditions. The study provides rare field-scale data on the physical limits of detonation in low-sensitivity energetic materials, obtained under realistic underground artisanal mining conditions.
- 10 March 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (6) , 2630
Open AccessExperimental Evaluation of Agricultural Ammonium Nitrate as an Explosive in Underground Artisanal Mining
The use of agricultural-grade ammonium nitrate without fuel oil as an explosive has been empirically observed in underground artisanal mining in Ecuador. Despite its practical adoption, the explosive behaviour of this material has not been adequately characterized through experimental measurements. This study presents an experimental evaluation of agricultural ammonium nitrate used as an explosive in underground artisanal mining, with velocity of detonation (VOD) employed as the main control variable. Field-scale experiments were conducted under confined conditions and through in situ measurements in underground production tunnels, using configurations involving ammonium nitrate and commercial emulsion explosives. VOD measurements were performed using a high-sensitivity recording system suitable for short charge lengths. The results show that the emulsion explosive detonated reliably, whereas detonation transferred to the ammonium nitrate column rapidly weakened and collapsed. Detonation propagation within the ammonium nitrate was limited to short distances or extinguished entirely, indicating a non-ideal detonation regime in which sustained propagation cannot be maintained under underground artisanal mining conditions. The study provides rare field-scale data on the physical limits of detonation in low-sensitivity energetic materials, obtained under realistic underground artisanal mining conditions.
- Open Access
- 8 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 655
Macroscopic and Microscopic Investigation on Microfractures in Blast-Conditioned Rock and the Influence of Particle Size
In the mining industry, particle size reduction is the most energy-demanding activity. Blasting represents the first stage of comminution. Experimental and field observations have demonstrated that blasting produces two main effects on rock: (i) macroscopic fracturing and fragmentation, and (ii) microscopic fracturing, consisting of a network of microfractures that weaken the rock, reduce the specific Work Index, and make the material less resistant to crushing and milling. The present work represents an initial investigation into the relationship between blast-induced microfracturing, fragment size, and mechanical resistance. Blasted rock was analyzed using three approaches: macroscopic testing via point load tests, laboratory grinding tests using a Bond ball mill to determine the blasted Work Index, and microscopic optical observation of microfractures. The results show that macroscopic testing is unable to detect microscopic weakening, as no correlation was observed between point load strength and particle size. In contrast, laboratory ball mill tests and microscopic optical observations indicate a preliminary relationship between particle size and the internal weakening of particles. These results allow the formulation of a new hypothesis: that the Work Index may not be constant within a given volume of blasted rock and could depend on the particle size distribution.
- 8 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 655
Open AccessMacroscopic and Microscopic Investigation on Microfractures in Blast-Conditioned Rock and the Influence of Particle Size
In the mining industry, particle size reduction is the most energy-demanding activity. Blasting represents the first stage of comminution. Experimental and field observations have demonstrated that blasting produces two main effects on rock: (i) macroscopic fracturing and fragmentation, and (ii) microscopic fracturing, consisting of a network of microfractures that weaken the rock, reduce the specific Work Index, and make the material less resistant to crushing and milling. The present work represents an initial investigation into the relationship between blast-induced microfracturing, fragment size, and mechanical resistance. Blasted rock was analyzed using three approaches: macroscopic testing via point load tests, laboratory grinding tests using a Bond ball mill to determine the blasted Work Index, and microscopic optical observation of microfractures. The results show that macroscopic testing is unable to detect microscopic weakening, as no correlation was observed between point load strength and particle size. In contrast, laboratory ball mill tests and microscopic optical observations indicate a preliminary relationship between particle size and the internal weakening of particles. These results allow the formulation of a new hypothesis: that the Work Index may not be constant within a given volume of blasted rock and could depend on the particle size distribution.
- Open Access
- 7 October 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (19) , 8894
Public Mining Governance for Sustainable Artisanal Gold Mining: Preventing Mercury Pollution in South America
Artisanal and small-scale gold mining (ASGM) constitutes an essential livelihood strategy for marginalized communities, yet it is also associated with severe environmental and social challenges. Persistent inequality and poverty underpin miners’ dependence on informal practices, where access to safer technologies is limited. Mercury use remains critical in ASGM, often mismanaged in processing, applied in amalgamation, and released into air, water, and soils. An estimated 1000–2000 tonnes are emitted annually despite Minamata Convention commitments. This paper examines how mining governance can foster sustainable transitions in ASGM, focusing on the Chilean National Mining Company (ENAMI) as a case study. ENAMI’s model—combining regulatory oversight, institutional support, and inclusive decision-making—shows how public governance can reduce mercury reliance, mitigate environmental degradation, and enhance social inclusion. Findings highlight the importance of regulation, community participation, capacity-building, and addressing structural inequalities as integral components of sustainability. The study argues that sustainable ASGM requires not only technical innovation but also culturally sensitive institutional reforms capable of overcoming resistance and promoting long-term behavioral change. By situating ASGM within the broader framework of sustainable rural development, this research provides insights for policymakers, practitioners, and scholars seeking to reconcile economic inclusion with environmental stewardship in vulnerable contexts.
- 7 October 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (19) , 8894
Open AccessPublic Mining Governance for Sustainable Artisanal Gold Mining: Preventing Mercury Pollution in South America
Artisanal and small-scale gold mining (ASGM) constitutes an essential livelihood strategy for marginalized communities, yet it is also associated with severe environmental and social challenges. Persistent inequality and poverty underpin miners’ dependence on informal practices, where access to safer technologies is limited. Mercury use remains critical in ASGM, often mismanaged in processing, applied in amalgamation, and released into air, water, and soils. An estimated 1000–2000 tonnes are emitted annually despite Minamata Convention commitments. This paper examines how mining governance can foster sustainable transitions in ASGM, focusing on the Chilean National Mining Company (ENAMI) as a case study. ENAMI’s model—combining regulatory oversight, institutional support, and inclusive decision-making—shows how public governance can reduce mercury reliance, mitigate environmental degradation, and enhance social inclusion. Findings highlight the importance of regulation, community participation, capacity-building, and addressing structural inequalities as integral components of sustainability. The study argues that sustainable ASGM requires not only technical innovation but also culturally sensitive institutional reforms capable of overcoming resistance and promoting long-term behavioral change. By situating ASGM within the broader framework of sustainable rural development, this research provides insights for policymakers, practitioners, and scholars seeking to reconcile economic inclusion with environmental stewardship in vulnerable contexts.
- Open Access
- 18 January 2025
- Published by MDPI AG in Preprints.org
Evidences of the Influence of Particle Size on the Incidence of Micro-Fractures in Blast-Conditioned Rock
In the mining industry the most energy/demanding activity is particle size reduction, i.e. comminution. Blasting is the first stage of comminution. It has been experimentally and by field observation demonstrated that blasting produces two effects on rock: i) it produces macroscopic fracturing, fragmentation; ii) it generates microscopic fracturing, a series of microfractures that weaken the rock, reducing the specific Work Index, therefore making it less resistant to crushing and milling. The present work is aimed to verify the following hypothesis: do smaller particles, having been macroscopically more affected by blasting, also possess a higher degree of microfractures, therefore being less resistant to grinding? To verify this hypothesis we analyzed blasted rock under three test dominions: macroscopic testing via point loading, laboratory grinding testing via Bond’s mill to determine the blasted Work Index and microscopic optical observation of microfractures. The results show that macroscopic testing cannot appreciate microscopic weakening (no correlation between point load results and particle size). On the other hand, laboratory ball mill and microscopic optical observation results show a direct correlation between particle size and internal weakening of particles. The results are evidence, albeit very preliminary, that the Work Index might not be a constant within a given volume of blasted rock, and it could be a function of particle size distribution.
- 18 January 2025
- Published by MDPI AG in Preprints.org
Open AccessEvidences of the Influence of Particle Size on the Incidence of Micro-Fractures in Blast-Conditioned Rock
In the mining industry the most energy/demanding activity is particle size reduction, i.e. comminution. Blasting is the first stage of comminution. It has been experimentally and by field observation demonstrated that blasting produces two effects on rock: i) it produces macroscopic fracturing, fragmentation; ii) it generates microscopic fracturing, a series of microfractures that weaken the rock, reducing the specific Work Index, therefore making it less resistant to crushing and milling. The present work is aimed to verify the following hypothesis: do smaller particles, having been macroscopically more affected by blasting, also possess a higher degree of microfractures, therefore being less resistant to grinding? To verify this hypothesis we analyzed blasted rock under three test dominions: macroscopic testing via point loading, laboratory grinding testing via Bond’s mill to determine the blasted Work Index and microscopic optical observation of microfractures. The results show that macroscopic testing cannot appreciate microscopic weakening (no correlation between point load results and particle size). On the other hand, laboratory ball mill and microscopic optical observation results show a direct correlation between particle size and internal weakening of particles. The results are evidence, albeit very preliminary, that the Work Index might not be a constant within a given volume of blasted rock, and it could be a function of particle size distribution.
- Open Access
- 26 September 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 124 (7) , 407-414
Influence of blasting charge distribution on the energy required for communition of rock
The most energy-intensive process in the mining industry is particle size reduction - comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq's half-space size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.
- 26 September 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 124 (7) , 407-414
Open AccessInfluence of blasting charge distribution on the energy required for communition of rock
The most energy-intensive process in the mining industry is particle size reduction - comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq's half-space size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.
- Open Access
- 28 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (11) , 4657
The Role of Delays in the Performance of Blasting
When researching rock blasting, the design parameters typically used for analysis are the geometric and charging parameters. This study focuses on a different approach based on the effect of timing, specifically the role of delays in the initiation sequence. Data were obtained from the results of full-scale blasts. The experimental setting and location allowed us to consider all parameters, other than the number of delays, as constants. The experimental results were analyzed, relating the delay variables to the fragmentation and KPIs of downstream operations. It was found that increasing the number of delays per unit of blasted rock and reducing simultaneous adjacent holes produces finer fragmentation, reduces the amount of fines, facilitates secondary operations, and reduces the risk of flyrock.
- 28 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (11) , 4657
Open AccessThe Role of Delays in the Performance of Blasting
When researching rock blasting, the design parameters typically used for analysis are the geometric and charging parameters. This study focuses on a different approach based on the effect of timing, specifically the role of delays in the initiation sequence. Data were obtained from the results of full-scale blasts. The experimental setting and location allowed us to consider all parameters, other than the number of delays, as constants. The experimental results were analyzed, relating the delay variables to the fragmentation and KPIs of downstream operations. It was found that increasing the number of delays per unit of blasted rock and reducing simultaneous adjacent holes produces finer fragmentation, reduces the amount of fines, facilitates secondary operations, and reduces the risk of flyrock.
- Open Access
- 9 May 2024
- Published by MDPI AG in Preprints.org
The Role of Delays in the Performance of Blasting
When researching rock blasting, the design parameters used for the analysis are usually the ge-ometric and charging ones. This study is based on a different approach, and focuses on the effect of timing, in specific the role of delays in the initiation sequence. The data come from the results of full-scale blasts. The experimental setting and location allowed to consider all parameter other than the number of delays as a constant. The experimental results are analyzed relating the delay var-iables to fragmentation and KPIs of downstream operations. It is shown how increasing the number of delays per unit of blasted rock and reducing simultaneous adjacent holes produces finer fragmentation, reduces the amount of fines, facilitates the secondary operations and reduces the risk of flyrock.
- 9 May 2024
- Published by MDPI AG in Preprints.org
Open AccessThe Role of Delays in the Performance of Blasting
When researching rock blasting, the design parameters used for the analysis are usually the ge-ometric and charging ones. This study is based on a different approach, and focuses on the effect of timing, in specific the role of delays in the initiation sequence. The data come from the results of full-scale blasts. The experimental setting and location allowed to consider all parameter other than the number of delays as a constant. The experimental results are analyzed relating the delay var-iables to fragmentation and KPIs of downstream operations. It is shown how increasing the number of delays per unit of blasted rock and reducing simultaneous adjacent holes produces finer fragmentation, reduces the amount of fines, facilitates the secondary operations and reduces the risk of flyrock.