Shigeya Kimura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shigeya Kimura has a total of 127 co-authors. Here are the top co-authors by number of shared publications:
S. Hasegawa
11 shared publicationsS. Emura
10 shared publicationsHisashi Yoshida
Corporate Research and Development Center, Toshiba Corporation 1 , 1 Komukai-Toshiba-cho, Saiwai-ku, Kawasaki, Kanagawa 212-8582, Japan
9 shared publications- Hajime Asahi
Osaka University
8 shared publications H. Asahi
Osaka University
6 shared publicationsHajime Asahi
The Institute of Scientific and Industrial Research, Osaka University, 8‐1 Mihoga‐oka, Ibaraki, Osaka 567‐0047, Japan
6 shared publications
Latest Publications
- Open Access
- 20 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 160903
Demonstration of a compact, self-contained, glass-encapsulated thermionic energy converter with an n-type AlGaN cathode
This study demonstrates a compact, self-contained, glass-encapsulated prototype thermionic energy converter (TEC) operating at around 300 °C, a remarkably low temperature for thermionic power generation. The device employs an n-type AlGaN thermionic cathode and is hermetically sealed in a glass-sealed Kovar package with a 3 cm‐diameter base. It consists of an AlGaN cathode, a perforated SUS anode, and a vacuum gap defined by insulating beads, together with an internal Cs accumulation region. Upon heating to 302 °C, the TEC produced an open-circuit voltage of 0.33 V and a short-circuit current density of 1.3 μA cm −2 .
- 20 August 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (16) , 160903
Open AccessDemonstration of a compact, self-contained, glass-encapsulated thermionic energy converter with an n-type AlGaN cathode
This study demonstrates a compact, self-contained, glass-encapsulated prototype thermionic energy converter (TEC) operating at around 300 °C, a remarkably low temperature for thermionic power generation. The device employs an n-type AlGaN thermionic cathode and is hermetically sealed in a glass-sealed Kovar package with a 3 cm‐diameter base. It consists of an AlGaN cathode, a perforated SUS anode, and a vacuum gap defined by insulating beads, together with an internal Cs accumulation region. Upon heating to 302 °C, the TEC produced an open-circuit voltage of 0.33 V and a short-circuit current density of 1.3 μA cm −2 .
- 15 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP02
Photon-enhanced thermionic emission characteristics of Cs deposited Mg-doped InGaN
The effect of Mg doping on photon-enhanced thermionic emission (PETE) of InGaN emitters was investigated to reduce the high operating temperatures of thermionic energy converters (TECs). Mg-doped In0.15Ga0.85N enabled TEC operation at 100 °C and enhanced power generation at lower temperatures (100-400°C). In contrast, In0.15Ga0.85N without Mg doping required temperatures above 300 °C. Notably, the output power of TEC using Mg-doped In0.15Ga0.85N was approximately 8.6 times higher at 400 °C than that of InGaN emitter without Mg doping. This enhancement is attributed to Mg doping, which reduces the energy barrier for electron emission and increase the quasi-Fermi level under light irradiation. However, the performance of Mg-doped InGaN decreased at temperatures exceeding 400 °C, due to the limited availability of thermally excited electrons in p-type semiconductors and the increased work function resulting from Cs desorption. Overall, Mg-doped InGaN demonstrates strong potential as a PETE emitter for low-temperature operation and visible-light-driven applications.
- 15 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP02
Photon-enhanced thermionic emission characteristics of Cs deposited Mg-doped InGaN
The effect of Mg doping on photon-enhanced thermionic emission (PETE) of InGaN emitters was investigated to reduce the high operating temperatures of thermionic energy converters (TECs). Mg-doped In0.15Ga0.85N enabled TEC operation at 100 °C and enhanced power generation at lower temperatures (100-400°C). In contrast, In0.15Ga0.85N without Mg doping required temperatures above 300 °C. Notably, the output power of TEC using Mg-doped In0.15Ga0.85N was approximately 8.6 times higher at 400 °C than that of InGaN emitter without Mg doping. This enhancement is attributed to Mg doping, which reduces the energy barrier for electron emission and increase the quasi-Fermi level under light irradiation. However, the performance of Mg-doped InGaN decreased at temperatures exceeding 400 °C, due to the limited availability of thermally excited electrons in p-type semiconductors and the increased work function resulting from Cs desorption. Overall, Mg-doped InGaN demonstrates strong potential as a PETE emitter for low-temperature operation and visible-light-driven applications.
- 1 May 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (5) , 051002
Surface activation of n-type AlGaN with cesium and oxygen to enhance thermionic emission
The aim of this study is to enhance the characteristics of thermionic emission of AlGaN surface through surface control employing cesium (Cs) and oxygen. Cs-deposited AlGaN has significant applications in thermionic energy converters. However, as the emitter temperature increases, the thermal desorption of Cs from AlGaN surface increases, resulting in a decrease in the thermionic emission current. Therefore, focusing on the high affinity between Cs and oxygen, we investigated the possibility of suppressing thermal desorption by depositing Cs and oxygen on AlGaN surface. The thermionic emission current measured when Cs and oxygen were alternately deposited on AlGaN surface was 1.9 × 10−3 A cm−2 at 500 °C. The thermionic emission current was significantly higher than that obtained with Cs-only deposition (2.0 × 10−5 A cm−2). In addition, we attempted to reproduce the effect of dynamic surface changes on thermionic emission employing a new thermionic emission model (modified Richardson–Dushman model) that considers the correlation between a specific surface reconstruction phase and its thermionic emission component. The results suggest that the adsorbed component of Cs-deposited AlGaN exhibits three Cs adsorption sites with different desorption energies, while the adsorbed component of Cs/O2 co-deposited AlGaN exhibits at least four Cs adsorption sites with different desorption energies. It is suggested that the increase in adsorption components with higher desorption energies, caused by the deposition of oxygen, may have reduced the thermal desorption and improved Cs coverage and stability.
- 1 May 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (5) , 051002
Surface activation of n-type AlGaN with cesium and oxygen to enhance thermionic emission
The aim of this study is to enhance the characteristics of thermionic emission of AlGaN surface through surface control employing cesium (Cs) and oxygen. Cs-deposited AlGaN has significant applications in thermionic energy converters. However, as the emitter temperature increases, the thermal desorption of Cs from AlGaN surface increases, resulting in a decrease in the thermionic emission current. Therefore, focusing on the high affinity between Cs and oxygen, we investigated the possibility of suppressing thermal desorption by depositing Cs and oxygen on AlGaN surface. The thermionic emission current measured when Cs and oxygen were alternately deposited on AlGaN surface was 1.9 × 10−3 A cm−2 at 500 °C. The thermionic emission current was significantly higher than that obtained with Cs-only deposition (2.0 × 10−5 A cm−2). In addition, we attempted to reproduce the effect of dynamic surface changes on thermionic emission employing a new thermionic emission model (modified Richardson–Dushman model) that considers the correlation between a specific surface reconstruction phase and its thermionic emission component. The results suggest that the adsorbed component of Cs-deposited AlGaN exhibits three Cs adsorption sites with different desorption energies, while the adsorbed component of Cs/O2 co-deposited AlGaN exhibits at least four Cs adsorption sites with different desorption energies. It is suggested that the increase in adsorption components with higher desorption energies, caused by the deposition of oxygen, may have reduced the thermal desorption and improved Cs coverage and stability.
- 27 May 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15 (6) , 061006
Diamond hollow cathode with axial magnetic field for high-density cold plasma source
We present a high-density plasma source using a hollow cathode with an axial magnetic field. The hollow cathode consists of molybdenum plates coated by polycrystalline boron-doped diamond (PBDD) with a high yield of ion-induced secondary electrons. Impact ionization was promoted by gyromotion in the hollow cathode with a magnetic field. A normalized current density four orders of magnitude larger than that of a planar cathode without a magnetic field was obtained. The high-quality PBDD cathode enables lower discharge sustain voltage and higher current density without glow-to-arc transition compared with low-quality PBDD and other cathode materials.
- 27 May 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15 (6) , 061006
Diamond hollow cathode with axial magnetic field for high-density cold plasma source
We present a high-density plasma source using a hollow cathode with an axial magnetic field. The hollow cathode consists of molybdenum plates coated by polycrystalline boron-doped diamond (PBDD) with a high yield of ion-induced secondary electrons. Impact ionization was promoted by gyromotion in the hollow cathode with a magnetic field. A normalized current density four orders of magnitude larger than that of a planar cathode without a magnetic field was obtained. The high-quality PBDD cathode enables lower discharge sustain voltage and higher current density without glow-to-arc transition compared with low-quality PBDD and other cathode materials.
- 1 November 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 39 (6) , 062207
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN/GaN cathodes
Enhanced thermionic emission (TE) and conversion characteristics are observed by controlling spontaneous and piezoelectric polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. Reduction in the electron affinity and work function by the insertion of an N-polarity thin n-type AlGaN (n-AlGaN) film including tensile biaxial strain is confirmed by an ultraviolet photoemission spectroscopy analysis. The obtained TE current from N-polarity n-AlGaN films grown on an n-type GaN (n-GaN) substrate is 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current is 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 1 November 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 39 (6) , 062207
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN/GaN cathodes
Enhanced thermionic emission (TE) and conversion characteristics are observed by controlling spontaneous and piezoelectric polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. Reduction in the electron affinity and work function by the insertion of an N-polarity thin n-type AlGaN (n-AlGaN) film including tensile biaxial strain is confirmed by an ultraviolet photoemission spectroscopy analysis. The obtained TE current from N-polarity n-AlGaN films grown on an n-type GaN (n-GaN) substrate is 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current is 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 5 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN cathodes
We observed enhancement of thermionic emission (TE) and conversion (TC) characteristics by controlling spontaneous and piezo polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. The obtained TE current from N-polarity n-AlGaN films grown on an n-GaN substrate was 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current was 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 5 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Enhancement of thermionic emission and conversion characteristics using polarization- and band-engineered n-type AlGaN cathodes
We observed enhancement of thermionic emission (TE) and conversion (TC) characteristics by controlling spontaneous and piezo polarization and the band diagram of n-type AlGaN/GaN thermionic cathodes. The obtained TE current from N-polarity n-AlGaN films grown on an n-GaN substrate was 0.29 mA at 500 °C in a Cs gas atmosphere in the vacuum gap between the cathode and a stainless steel anode. This TE current was 5.0 times and 1.6 times higher than that from the surface of Ga-polarity n-GaN substrate and that of the Ga-polarity n-AlGaN film on the substrate, respectively.
- 1 January 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 39 (1) , 014201
Surface polarity dependence of thermionic emission and conversion characteristics of n-type GaN cathodes
We observed the polarity-dependent thermionic emission (TE) and conversion characteristics of n-type GaN-based cathodes with Cs adsorbed on their surfaces. TE current from the surface of an n-GaN sample with N-polarity was 0.18 mA at an applied anode voltage of 30 V at 500 °C. This TE current was markedly higher than that of a sample with Ga-polarity, which had a corresponding TE current of 0.063 mA. We consider the N-polarity with spontaneous polarization to be the cause of the increase in electron density at the Cs/n-GaN interface. TE current was also detected from both samples with Ga- and N-polarity even when the applied anode voltage was 0 V or lower, indicating the presence of thermionic conversion characteristics. From the viewpoint of a thermionic converter, the electromotive force for TE was 0.12 V higher when using the N-polarity n-GaN cathode compared with the Ga-polarity cathode. The short-circuit currents at 500 °C were 4.8 and 0.97 μA for the sample with N-polarity and the one with Ga-polarity, respectively.
- 1 January 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 39 (1) , 014201
Surface polarity dependence of thermionic emission and conversion characteristics of n-type GaN cathodes
We observed the polarity-dependent thermionic emission (TE) and conversion characteristics of n-type GaN-based cathodes with Cs adsorbed on their surfaces. TE current from the surface of an n-GaN sample with N-polarity was 0.18 mA at an applied anode voltage of 30 V at 500 °C. This TE current was markedly higher than that of a sample with Ga-polarity, which had a corresponding TE current of 0.063 mA. We consider the N-polarity with spontaneous polarization to be the cause of the increase in electron density at the Cs/n-GaN interface. TE current was also detected from both samples with Ga- and N-polarity even when the applied anode voltage was 0 V or lower, indicating the presence of thermionic conversion characteristics. From the viewpoint of a thermionic converter, the electromotive force for TE was 0.12 V higher when using the N-polarity n-GaN cathode compared with the Ga-polarity cathode. The short-circuit currents at 500 °C were 4.8 and 0.97 μA for the sample with N-polarity and the one with Ga-polarity, respectively.
- Open Access
- 9 April 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
Surface Electronic Properties of Si‐Doped AlGaN and Thermionic Emission Characteristics with Adsorption of Alkali Metal Atoms
- 9 April 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
Open AccessSurface Electronic Properties of Si‐Doped AlGaN and Thermionic Emission Characteristics with Adsorption of Alkali Metal Atoms
- Open Access
- 3 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGF01
Thermionic emission and conversion properties of n-type AlGaN thin film cathodes grown on 6H–SiC substrates
We observed the thermionic emission (TE) and conversion (TC) characteristics of Si-doped AlGaN thin film cathodes grown on n-type 6H-SiC substrates with Cs adsorption on the surfaces. The threshold temperatures of TE decreased as the AlN mole fraction was increased, with threshold temperatures of around 205 °C for Si–doped Al 0.5 Ga 0.5 N. TE was detected even when the applied external voltage was 0 V at 600 °C, which means that the cathodes had TC characteristics at a temperature dramatically lower than that of conventional systems with metal-based cathodes. In addition, we observed a notable enhancement of the emission current when the cathodes were irradiated with white light having energy lower than that of the bandgap of the AlGaN films at low temperatures. We suggest that the enhancement was caused by an internal photoelectron effect due to the absorption of the light in the n–type 6H–SiC substrate.
- 3 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGF01
Open AccessThermionic emission and conversion properties of n-type AlGaN thin film cathodes grown on 6H–SiC substrates
We observed the thermionic emission (TE) and conversion (TC) characteristics of Si-doped AlGaN thin film cathodes grown on n-type 6H-SiC substrates with Cs adsorption on the surfaces. The threshold temperatures of TE decreased as the AlN mole fraction was increased, with threshold temperatures of around 205 °C for Si–doped Al 0.5 Ga 0.5 N. TE was detected even when the applied external voltage was 0 V at 600 °C, which means that the cathodes had TC characteristics at a temperature dramatically lower than that of conventional systems with metal-based cathodes. In addition, we observed a notable enhancement of the emission current when the cathodes were irradiated with white light having energy lower than that of the bandgap of the AlGaN films at low temperatures. We suggest that the enhancement was caused by an internal photoelectron effect due to the absorption of the light in the n–type 6H–SiC substrate.
- 13 November 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
Surface Electronic Properties of Si‐Doped AlGaN and Thermionic Emission Characteristics with Adsorption of Alkali Metal Atoms
A thermionic energy converter (TEC) is a heat engine with a high theoretical efficiency, but a reduction in operating temperature is required for practical applications. Herein, the experimentally determined thermionic conversion characteristics of Si‐doped GaN films with Cs adsorption at 600 °C are reported. Low‐temperature thermionic emission around 300 °C is also reported for Si‐doped AlGaN surfaces with Cs adsorption. This emission temperature is considerably lower than the operating temperatures of conventional systems with a metal emitter. The AlGaN thin films are grown on n‐type 6H‐SiC substrates, and it is confirmed by ultraviolet photoelectron spectroscopy that the work function decreases as the AlN mole fraction x in the AlGaN samples is increased. Threshold temperatures of thermionic emission decrease with increasing AlN mole fraction and a corresponding reduction in the work function.
- 13 November 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
Surface Electronic Properties of Si‐Doped AlGaN and Thermionic Emission Characteristics with Adsorption of Alkali Metal Atoms
A thermionic energy converter (TEC) is a heat engine with a high theoretical efficiency, but a reduction in operating temperature is required for practical applications. Herein, the experimentally determined thermionic conversion characteristics of Si‐doped GaN films with Cs adsorption at 600 °C are reported. Low‐temperature thermionic emission around 300 °C is also reported for Si‐doped AlGaN surfaces with Cs adsorption. This emission temperature is considerably lower than the operating temperatures of conventional systems with a metal emitter. The AlGaN thin films are grown on n‐type 6H‐SiC substrates, and it is confirmed by ultraviolet photoelectron spectroscopy that the work function decreases as the AlN mole fraction x in the AlGaN samples is increased. Threshold temperatures of thermionic emission decrease with increasing AlN mole fraction and a corresponding reduction in the work function.