Amitabha Das
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Amitabha Das has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Ma Qian
School of Engineering, RMIT University, Melbourne, Australia
7 shared publications H.R. Kotadia
6 shared publications- Indranil Manna
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
6 shared publications S.K. Pabi
Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302, India
4 shared publicationsZ. Fan
4 shared publications- Hiren Ramniklal Kotadia
School of Engineering, Liverpool John Moores University, Liverpool, UK
3 shared publications
Latest Publications
- Open Access
- 29 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Identification of the role of zinc in Sn–Cu solder and interfacial intermetallic growth through experimental results and phase-field simulations
- 29 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessIdentification of the role of zinc in Sn–Cu solder and interfacial intermetallic growth through experimental results and phase-field simulations
- 17 September 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (18) , 2157-2164
Microstructural modification of Sn–Bi and Sn–Bi–Al immiscible alloys by shearing
Sn–20 wt-%Bi and immiscible Sn–20 wt-%Bi–1 wt-%Al alloys were used to understand the effect of high-intensity shearing on microstructural refinement. Novel ACME (Axial Centrifugal Metal Expeller) shearing device, based on axial compressor and rotor–stator mechanism to generate high shear rate and intense turbulence, was used to condition the melts prior to solidification. Microstructure in the Sn–Bi alloy deviated from dendritic grains with coarse eutectic pockets under conventional solidification to compact grains with well-dispersed eutectic under semisolid-state shearing. Decreasing the shearing temperature and increasing shearing time increased the globularity of grains. Following shearing, remnant liquid solidified into fine grain structure. In the immiscible Sn–Bi–Al alloy, shearing produced uniform dispersion of refined Al-rich particles in Sn-rich matrix as opposed to severe segregation under conventional solidification. The primary effect of shearing appears to originate from the thermo-solutal homogenisation of the melt and its effect on interface stability during solidification.
- 17 September 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (18) , 2157-2164
Microstructural modification of Sn–Bi and Sn–Bi–Al immiscible alloys by shearing
Sn–20 wt-%Bi and immiscible Sn–20 wt-%Bi–1 wt-%Al alloys were used to understand the effect of high-intensity shearing on microstructural refinement. Novel ACME (Axial Centrifugal Metal Expeller) shearing device, based on axial compressor and rotor–stator mechanism to generate high shear rate and intense turbulence, was used to condition the melts prior to solidification. Microstructure in the Sn–Bi alloy deviated from dendritic grains with coarse eutectic pockets under conventional solidification to compact grains with well-dispersed eutectic under semisolid-state shearing. Decreasing the shearing temperature and increasing shearing time increased the globularity of grains. Following shearing, remnant liquid solidified into fine grain structure. In the immiscible Sn–Bi–Al alloy, shearing produced uniform dispersion of refined Al-rich particles in Sn-rich matrix as opposed to severe segregation under conventional solidification. The primary effect of shearing appears to originate from the thermo-solutal homogenisation of the melt and its effect on interface stability during solidification.
- 16 February 2019
- Published by Springer Nature
- p. 1589-1595
Effect of Ultrasonication on the Solidification Microstructure in Al and Mg-Alloys
- 16 February 2019
- Published by Springer Nature
- p. 1589-1595
Effect of Ultrasonication on the Solidification Microstructure in Al and Mg-Alloys
- Open Access
- 23 January 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (5) , 2731-2736
Influence of Zn Concentration on Interfacial Intermetallics During Liquid and Solid State Reaction of Hypo and Hypereutectic Sn-Zn Solder Alloys
- 23 January 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (5) , 2731-2736
Open AccessInfluence of Zn Concentration on Interfacial Intermetallics During Liquid and Solid State Reaction of Hypo and Hypereutectic Sn-Zn Solder Alloys
- Open Access
- 3 October 2018
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 71 (11) , 2681-2686
Solidification of Aluminium Alloys Under Ultrasonication: An Overview
- 3 October 2018
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 71 (11) , 2681-2686
Open AccessSolidification of Aluminium Alloys Under Ultrasonication: An Overview
- 1 October 2017
- Published by Elsevier in Materials & Design
- Vol. 132, 266-274
On the microstructural refinement in commercial purity Al and Al-10 wt% Cu alloy under ultrasonication during solidification
- 1 October 2017
- Published by Elsevier in Materials & Design
- Vol. 132, 266-274
On the microstructural refinement in commercial purity Al and Al-10 wt% Cu alloy under ultrasonication during solidification
- 1 January 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 620, 1-4
Modification of solidification microstructure in hypo- and hyper-eutectic Al–Si alloys under high-intensity ultrasonic irradiation
- 1 January 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 620, 1-4
Modification of solidification microstructure in hypo- and hyper-eutectic Al–Si alloys under high-intensity ultrasonic irradiation
- 1 December 2011
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 131 (1-2) , 241-249
A comparative study of ternary Al–Sn–Cu immiscible alloys prepared by conventional casting and casting under high-intensity ultrasonic irradiation
- 1 December 2011
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 131 (1-2) , 241-249
A comparative study of ternary Al–Sn–Cu immiscible alloys prepared by conventional casting and casting under high-intensity ultrasonic irradiation